Some (defective) PCIe devices are not able to reliably do link retraining.
Check to see if ASPM is possible between link partners before configuring
common clocking, and doing the resulting link retraining. If ASPM is not
possible, there is no reason to risk losing access to a device due to an
unnecessary link retraining.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If an error occurs when enabling a slot, pciehp_power_thread() turns off
the power indicator. But if the only error is that the slot was already
enabled, we should leave the power indicator on.
Return success if called to enable an already-enabled slot.
This is in the same spirit of the special handling for EEXISTS when
pciehp_configure_device() determines the slot devices already exist.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
If Slot Status indicates changes in both Data Link Layer Status and
Presence Detect, prioritize the Link status change.
When both events are observed, pciehp currently relies on the Slot Status
Presence Detect State (PDS) to agree with the Link Status Data Link Layer
Active status. The Presence Detect State, however, may be set to 1 through
out-of-band presence detect even if the link is down, which creates
conflicting events.
Since the Link Status accurately reflects the reachability of the
downstream bus, the Link Status event should take precedence over a
Presence Detect event. Skip checking the PDC status if we handled a link
event in the same handler.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull the register resource lookup out of thunder_pem_init() so we can
easily add a corresponding lookup using ACPI. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Qualcomm Technologies QDF2432 SoC does not support accesses smaller
than 32 bits to the PCI configuration space. Register the appropriate
quirk.
[bhelgaas: add QCOM_ECAM32 macro, ifdef for ACPI and PCI_QUIRKS]
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most error branches following the call to pci_enable_device() contain a
call to pci_disable_device(). Add these calls where they are missing.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Hardware that supports only 32-bit config writes is not spec-compliant.
For example, if software performs a 16-bit write, we must do a 32-bit read,
merge in the 16 bits we intend to write, followed by a 32-bit write. If
the 16 bits we *don't* intend to write happen to have any RW1C (write-one-
to-clear) bits set, we just inadvertently cleared something we shouldn't
have.
Add a rate-limited warning when we do sub-32 bit config writes. Remove
similar probe-time warnings from some of the affected host bridge drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enthusiastically-Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com> # rockchip
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the revision isn't available via sysfs/libudev thus if one wants
to know the value one needs to read through the config file, which can be
quite time-consuming because it wakes/powers up the device.
There are at least two userspace components which could make use the new
file: libpciaccess and libdrm. The former wakes up _every_ PCI device,
which can be observed via glxinfo when using Mesa 10.0+ drivers. The
latter, in association with Mesa 13.0, can lead to 2-3 second delays while
starting firefox, thunderbird or chromium.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98502
Tested-by: Mauro Santos <registo.mailling@gmail.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch
CC: Greg KH <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the source
code, improves readability, and reduces the chance of inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Body of an "if" statement wasn't indented. Add a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Include the PCIE_HIP06_CTRL_OFF block base in the PCIE_SYS_STATE4 register
address so reads of PCIE_SYS_STATE4 don't have to mention both. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xilinx-nwl driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
xilinx_pcie_assign_msi() doesn't use the struct xilinx_pcie_port pointer
passed to it, so remove the argument completely. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xilinx driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the struct xgene_pcie_port pointer, not addresses, to setup functions.
This enables future simplifications. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xgene driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The tegra driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The tegra_pcie_phy_disable() path called pads_writel() with arguments in
the wrong order. Swap them to be the "value, offset" order expected by
pads_writel().
Fixes: 6fe7c187e0 ("PCI: tegra: Support per-lane PHYs")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
CC: stable@vger.kernel.org # v4.7+
The rockchip driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The DRV_NAME macro is only used once, so there's no real advantage to
having the macro at all. Remove it and use the "rcar-pcie" name directly
in the struct platform_driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
rcar_pcie_get_resources() doesn't use the platform_device pointer passed to
it, so remove it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The rcar driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Remove the struct qcom_pcie.dev member, which is a duplicate of the generic
pp.dev member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct qcom_pcie.dbi member, which is a duplicate of the generic
pp.dbi_base member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the existing "np" pointer instead of looking up dev->of_node again. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
