Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix incorrect sockopts unregistration from error path,
from Florian Westphal.
2) A few patches to provide better error reporting when missing kernel
netfilter options are missing in .config.
3) Fix dormant table flag updates.
4) Memleak in IPVS when adding service with IP_VS_SVC_F_HASHED flag.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
ipvs: ignore IP_VS_SVC_F_HASHED flag when adding service
netfilter: nf_tables: fix table flag updates
netfilter: nf_tables: extended netlink error reporting for chain type
netfilter: nf_tables: missing error reporting for not selected expressions
netfilter: conntrack: unregister ipv4 sockopts on error unwind
====================
Link: https://lore.kernel.org/r/20210527190115.98503-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix current behavior of skipping template allocation in case the
ct action is in zone 0.
Skipping the allocation may cause the datapath ct code to ignore the
entire ct action with all its attributes (commit, nat) in case the ct
action in zone 0 was preceded by a ct clear action.
The ct clear action sets the ct_state to untracked and resets the
skb->_nfct pointer. Under these conditions and without an allocated
ct template, the skb->_nfct pointer will remain NULL which will
cause the tc ct action handler to exit without handling commit and nat
actions, if such exist.
For example, the following rule in OVS dp:
recirc_id(0x2),ct_state(+new-est-rel-rpl+trk),ct_label(0/0x1), \
in_port(eth0),actions:ct_clear,ct(commit,nat(src=10.11.0.12)), \
recirc(0x37a)
Will result in act_ct skipping the commit and nat actions in zone 0.
The change removes the skipping of template allocation for zone 0 and
treats it the same as any other zone.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/20210526170110.54864-1-lariel@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently established connections are not offloaded if the filter has a
"ct commit" action. This behavior will not offload connections of the
following scenario:
$ tc_filter add dev $DEV ingress protocol ip prio 1 flower \
ct_state -trk \
action ct commit action goto chain 1
$ tc_filter add dev $DEV ingress protocol ip chain 1 prio 1 flower \
action mirred egress redirect dev $DEV2
$ tc_filter add dev $DEV2 ingress protocol ip prio 1 flower \
action ct commit action goto chain 1
$ tc_filter add dev $DEV2 ingress protocol ip prio 1 chain 1 flower \
ct_state +trk+est \
action mirred egress redirect dev $DEV
Offload established connections, regardless of the commit flag.
Fixes: 46475bb20f ("net/sched: act_ct: Software offload of established flows")
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/1622029449-27060-1-git-send-email-paulb@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Physical port name, port number attributes do not belong to virtual port
flavour. When VF or SF virtual ports are registered they incorrectly
append "np0" string in the netdevice name of the VF/SF.
Before this fix, VF netdevice name were ens2f0np0v0, ens2f0np0v1 for VF
0 and 1 respectively.
After the fix, they are ens2f0v0, ens2f0v1.
With this fix, reading /sys/class/net/ens2f0v0/phys_port_name returns
-EOPNOTSUPP.
Also devlink port show example for 2 VFs on one PF to ensure that any
physical port attributes are not exposed.
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
pci/0000:06:00.3/196608: type eth netdev ens2f0v0 flavour virtual splittable false
pci/0000:06:00.4/262144: type eth netdev ens2f0v1 flavour virtual splittable false
This change introduces a netdevice name change on systemd/udev
version 245 and higher which honors phys_port_name sysfs file for
generation of netdevice name.
This also aligns to phys_port_name usage which is limited to switchdev
ports as described in [1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/tree/Documentation/networking/switchdev.rst
Fixes: acf1ee44ca ("devlink: Introduce devlink port flavour virtual")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20210526200027.14008-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to prevent
out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default
-----BEGIN PGP SIGNATURE-----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=peMK
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc4, including fixes from bpf, netfilter,
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface
ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to
prevent out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and
isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default"
* tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (172 commits)
net: phy: Document phydev::dev_flags bits allocation
mptcp: validate 'id' when stopping the ADD_ADDR retransmit timer
mptcp: avoid error message on infinite mapping
mptcp: drop unconditional pr_warn on bad opt
mptcp: avoid OOB access in setsockopt()
nfp: update maintainer and mailing list addresses
net: mvpp2: add buffer header handling in RX
bnx2x: Fix missing error code in bnx2x_iov_init_one()
net: zero-initialize tc skb extension on allocation
net: hns: Fix kernel-doc
sctp: fix the proc_handler for sysctl encap_port
sctp: add the missing setting for asoc encap_port
bpf, selftests: Adjust few selftest result_unpriv outcomes
bpf: No need to simulate speculative domain for immediates
bpf: Fix mask direction swap upon off reg sign change
bpf: Wrap aux data inside bpf_sanitize_info container
bpf: Fix BPF_LSM kconfig symbol dependency
selftests/bpf: Add test for l3 use of bpf_redirect_peer
bpftool: Add sock_release help info for cgroup attach/prog load command
net: dsa: microchip: enable phy errata workaround on 9567
...
Document the phydev::dev_flags bit allocation to allow bits 15:0 to
define PHY driver specific behavior, bits 23:16 to be reserved for now,
and bits 31:24 to hold generic PHY driver flags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210526184617.3105012-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-05-26
The following pull-request contains BPF updates for your *net* tree.
We've added 14 non-merge commits during the last 14 day(s) which contain
a total of 17 files changed, 513 insertions(+), 231 deletions(-).
The main changes are:
1) Fix bpf_skb_change_head() helper to reset mac_len, from Jussi Maki.
2) Fix masking direction swap upon off-reg sign change, from Daniel Borkmann.
3) Fix BPF offloads in verifier by reordering driver callback, from Yinjun Zhang.
4) BPF selftest for ringbuf mmap ro/rw restrictions, from Andrii Nakryiko.
5) Follow-up fixes to nested bprintf per-cpu buffers, from Florent Revest.
6) Fix bpftool sock_release attach point help info, from Liu Jian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
MPTCP fixes
Here are a few fixes for the -net tree.
Patch 1 fixes an attempt to access a tcp-specific field that does not
exist in mptcp sockets.
Patches 2 and 3 remove warning/error log output that could be flooded.
Patch 4 performs more validation on address advertisement echo packets
to improve RFC 8684 compliance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
when Linux receives an echo-ed ADD_ADDR, it checks the IP address against
the list of "announced" addresses. In case of a positive match, the timer
that handles retransmissions is stopped regardless of the 'Address Id' in
the received packet: this behaviour does not comply with RFC8684 3.4.1.
Fix it by validating the 'Address Id' in received echo-ed ADD_ADDRs.
Tested using packetdrill, with the following captured output:
unpatched kernel:
Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0xfd2e62517888fe29,mptcp dss ack 3007449509], length 0
In <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 1.2.3.4,mptcp dss ack 3013740213], length 0
Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0xfd2e62517888fe29,mptcp dss ack 3007449509], length 0
In <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 90 198.51.100.2,mptcp dss ack 3013740213], length 0
^^^ retransmission is stopped here, but 'Address Id' is 90
patched kernel:
Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
In <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 1.2.3.4,mptcp dss ack 1672384568], length 0
Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
In <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 90 198.51.100.2,mptcp dss ack 1672384568], length 0
Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
In <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 198.51.100.2,mptcp dss ack 1672384568], length 0
^^^ retransmission is stopped here, only when both 'Address Id' and 'IP Address' match
Fixes: 00cfd77b90 ("mptcp: retransmit ADD_ADDR when timeout")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another left-over. Avoid flooding dmesg with useless text,
we already have a MIB for that event.
Fixes: 648ef4b886 ("mptcp: Implement MPTCP receive path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a left-over of early day. A malicious peer can flood
the kernel logs with useless messages, just drop it.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use tcp_set_congestion_control() on an mptcp socket, as
such function can end-up accessing a tcp-specific field -
prior_ssthresh - causing an OOB access.
To allow propagating the correct ca algo on subflow, cache the ca
name at initialization time.
Additionally avoid overriding the user-selected CA (if any) at
clone time.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/182
Fixes: aa1fbd94e5 ("mptcp: sockopt: add TCP_CONGESTION and TCP_INFO")
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Netronome's activities and people have moved over to Corigine,
including NFP driver maintenance and myself.
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If Link Partner sends frames larger than RX buffer size, MAC mark it
as oversize but still would pass it to the Packet Processor.
In this scenario, Packet Processor scatter frame between multiple buffers,
but only a single buffer would be returned to the Buffer Manager pool and
it would not refill the poll.
Patch add handling of oversize error with buffer header handling, so all
buffers would be returned to the Buffer Manager pool.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix function name in hns_ethtool.c kernel-doc comment
to remove these warnings found by clang_w1.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:202: warning: expecting
prototype for hns_nic_set_link_settings(). Prototype was for
hns_nic_set_link_ksettings() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:837: warning: expecting
prototype for get_ethtool_stats(). Prototype was for
hns_get_ethtool_stats() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:894: warning:
expecting prototype for get_strings(). Prototype was for
hns_get_strings() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 'commit 262b38cdb3 ("net: ethernet: hisilicon: hns: use phydev
from struct net_device")'
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_dointvec() cannot do min and max check for setting a value
when extra1/extra2 is set, so change it to proc_dointvec_minmax()
for sysctl encap_port.
Fixes: e8a3001c21 ("sctp: add encap_port for netns sock asoc and transport")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add the missing setting back for asoc encap_port.
Fixes: 8dba29603b ("sctp: add SCTP_REMOTE_UDP_ENCAPS_PORT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix another "confused deputy" weakness[1]. Writes to /proc/$pid/attr/
files need to check the opener credentials, since these fds do not
transition state across execve(). Without this, it is possible to
trick another process (which may have different credentials) to write
to its own /proc/$pid/attr/ files, leading to unexpected and possibly
exploitable behaviors.
[1] https://www.kernel.org/doc/html/latest/security/credentials.html?highlight=confused#open-file-credentials
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given we don't need to simulate the speculative domain for registers with
immediates anymore since the verifier uses direct imm-based rewrites instead
of having to mask, we can also lift a few cases that were previously rejected.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
In 801c6058d1 ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.
Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.
Fixes: 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask")
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Similarly as 6bdacdb48e ("bpf: Fix BPF_JIT kconfig symbol dependency") we
need to detangle the hard BPF_LSM dependency on NET. This was previously
implicit by its dependency on BPF_JIT which itself was dependent on NET (but
without any actual/real hard dependency code-wise). Given the latter was
lifted, so should be the former as BPF_LSMs could well exist on net-less
systems. This therefore also fixes a randconfig build error recently reported
by Randy:
ld: kernel/bpf/bpf_lsm.o: in function `bpf_lsm_func_proto':
bpf_lsm.c:(.text+0x1a0): undefined reference to `bpf_sk_storage_get_proto'
ld: bpf_lsm.c:(.text+0x1b8): undefined reference to `bpf_sk_storage_delete_proto'
[...]
Fixes: b24abcff91 ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
-----BEGIN PGP SIGNATURE-----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=poNo
-----END PGP SIGNATURE-----
Merge tag 'netfs-lib-fixes-20200525' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfs fixes from David Howells:
"A couple of fixes to the new netfs lib:
- Pass the AOP flags through from netfs_write_begin() into
grab_cache_page_write_begin().
- Automatically enable in Kconfig netfs lib rather than presenting an
option for manual enablement"
* tag 'netfs-lib-fixes-20200525' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Make CONFIG_NETFS_SUPPORT auto-selected rather than manual
netfs: Pass flags through to grab_cache_page_write_begin()
Add a test case for using bpf_skb_change_head() in combination with
bpf_redirect_peer() to redirect a packet from a L3 device to veth and back.
The test uses a BPF program that adds L2 headers to the packet coming
from a L3 device and then calls bpf_redirect_peer() to redirect the packet
to a veth device. The test fails as skb->mac_len is not set properly and
thus the ethernet headers are not properly skb_pull'd in cls_bpf_classify(),
causing tcp_v4_rcv() to point the TCP header into middle of the IP header.
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210525102955.2811090-1-joamaki@gmail.com
The help information was not added at the time when the function got added.
Fix this and add the missing information to its cli, documentation and bash
completion.
Fixes: db94cc0b48 ("bpftool: Add support for BPF_CGROUP_INET_SOCK_RELEASE")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20210525014139.323859-1-liujian56@huawei.com
- Fix 'perf script' decoding of Intel PT traces for abort handling and
sample instruction bytes.
- Add missing PERF_IP_FLAG_CHARS for VM-Entry and VM-Exit to Intel PT
'perf script' decoder.
- Fixes for the python based Intel PT trace viewer GUI.
- Sync UAPI copies (unwire quotactl_path, some comment fixes).
- Fix handling of missing kernel software events, such as the recently
added 'cgroup-switches', and add the trivial glue for it in the
tooling side, since it was added in this merge window.
- Add missing initialization of zstd_data in 'perf buildid-list',
detected with valgrind's memcheck.
- Remove needless event enable/disable when all events uses BPF.
- Fix libpfm4 support (63) test error for nested event groups.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYKwENwAKCRCyPKLppCJ+
JxBWAP0UQ2Mm/STKDz4GpqJl1WsHF5oUUr8mFv+17ucyk4vdYgD/Xd5BaFNm6Y7E
/PgbNW9qze1ltWvHWGDpP/rFJfoNqg8=
=YzL3
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.13-2021-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix 'perf script' decoding of Intel PT traces for abort handling and
sample instruction bytes.
- Add missing PERF_IP_FLAG_CHARS for VM-Entry and VM-Exit to Intel PT
'perf script' decoder.
- Fixes for the python based Intel PT trace viewer GUI.
- Sync UAPI copies (unwire quotactl_path, some comment fixes).
- Fix handling of missing kernel software events, such as the recently
added 'cgroup-switches', and add the trivial glue for it in the
tooling side, since it was added in this merge window.
- Add missing initialization of zstd_data in 'perf buildid-list',
detected with valgrind's memcheck.
- Remove needless event enable/disable when all events uses BPF.
- Fix libpfm4 support (63) test error for nested event groups.
* tag 'perf-tools-fixes-for-v5.13-2021-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf stat: Skip evlist__[enable|disable] when all events uses BPF
perf script: Add missing PERF_IP_FLAG_CHARS for VM-Entry and VM-Exit
perf scripts python: exported-sql-viewer.py: Fix warning display
perf scripts python: exported-sql-viewer.py: Fix Array TypeError
perf scripts python: exported-sql-viewer.py: Fix copy to clipboard from Top Calls by elapsed Time report
tools headers UAPI: Sync files changed by the quotactl_path unwiring
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
perf parse-events: Check if the software events array slots are populated
perf tools: Add 'cgroup-switches' software event
perf intel-pt: Remove redundant setting of ptq->insn_len
perf intel-pt: Fix sample instruction bytes
perf intel-pt: Fix transaction abort handling
perf test: Fix libpfm4 support (63) test error for nested event groups
tools arch kvm: Sync kvm headers with the kernel sources
perf buildid-list: Initialize zstd_data
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.
backtrace:
[<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
[<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
[<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
[<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Cc: stable@kernel.vger.org
Reported-and-tested-by: syzbot+b558506ba8165425fee2@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr
in fill_frame_info") added the following which resulted in -EINVAL
always being returned:
if (skb->mac_len < sizeof(struct hsr_ethhdr))
return -EINVAL;
mac_len was not being set correctly so this check completely broke
HSR/PRP since it was always 14, not 20.
Set mac_len correctly and modify the mac_len checks to test in the
correct places since sometimes it is legitimately 14.
Fixes: 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr in fill_frame_info")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cops_probe1(), there is a write to dev->base_addr after requesting an
interrupt line and registering the interrupt handler cops_interrupt().
The handler might be called in parallel to handle an interrupt.
cops_interrupt() tries to read dev->base_addr leading to a potential
data race. So write to dev->base_addr before calling request_irq().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Saubhik Mukherjee <saubhik.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fixes for SJA1105 DSA driver
This series contains some minor fixes in the sja1105 driver:
- improved error handling in the probe path
- rejecting an invalid phy-mode specified in the device tree
- register access fix for SJA1105P/Q/R/S for the virtual links through
the dynamic reconfiguration interface
- handling 2 bridge VLANs where the second is supposed to overwrite the
first
- making sure that the lack of a pvid results in the actual dropping of
untagged traffic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When running this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp4 master br0
bridge vlan add dev swp4 vid 1
We observe the traffic sent on swp4 is still untagged, even though the
bridge has overwritten the existing VLAN entry:
port vlan ids
swp4 1 PVID
br0 1 PVID Egress Untagged
This happens because we didn't consider that the 'bridge vlan add'
command just overwrites VLANs like it's nothing. We treat the 'vid 1
pvid untagged' and the 'vid 1' as two separate VLANs, and the first
still has precedence when calling sja1105_build_vlan_table. Obviously
there is a disagreement regarding semantics, and we end up doing
something unexpected from the PoV of the bridge.
Let's actually consider an "existing VLAN" to be one which is on the
same port, and has the same VLAN ID, as one we already have, and update
it if it has different flags than we do.
The first blamed commit is the one introducing the bug, the second one
is the latest on top of which the bugfix still applies.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Fixes: 5899ee367a ("net: dsa: tag_8021q: add a context structure")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing became visible when writing the blamed commit, and that was
that STP and PTP frames injected by net/dsa/tag_sja1105.c using the
deferred xmit mechanism are always classified to the pvid of the CPU
port, regardless of whatever VLAN there might be in these packets.
So a decision needed to be taken regarding the mechanism through which
we should ensure that delivery of STP and PTP traffic is possible when
we are in a VLAN awareness mode that involves tag_8021q. This is because
tag_8021q is not concerned with managing the pvid of the CPU port, since
as far as tag_8021q is concerned, no traffic should be sent as untagged
from the CPU port. So we end up not actually having a pvid on the CPU
port if we only listen to tag_8021q, and unless we do something about it.
The decision taken at the time was to keep VLAN 1 in the list of
priv->dsa_8021q_vlans, and make it a pvid of the CPU port. This ensures
that STP and PTP frames can always be sent to the outside world.
However there is a problem. If we do the following while we are in
the best_effort_vlan_filtering=true mode:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1
Then untagged and pvid-tagged frames should be dropped. But we observe
that they aren't, and this is because of the precaution we took that VID
1 is always installed on all ports.
So clearly VLAN 1 is not good for this purpose. What about VLAN 0?
Well, VLAN 0 is managed by the 8021q module, and that module wants to
ensure that 802.1p tagged frames are always received by a port, and are
always transmitted as VLAN-tagged (with VLAN ID 0). Whereas we want our
STP and PTP frames to be untagged if the stack sent them as untagged -
we don't want the driver to just decide out of the blue that it adds
VID 0 to some packets.
So what to do?
Well, there is one other VLAN that is reserved, and that is 4095:
$ ip link add link swp2 name swp2.4095 type vlan id 4095
Error: 8021q: Invalid VLAN id.
$ bridge vlan add dev swp2 vid 4095
Error: bridge: Vlan id is invalid.
After we made this change, VLAN 1 is indeed forwarded and/or dropped
according to the bridge VLAN table, there are no further alterations
done by the sja1105 driver.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver continues probing when a port is configured for an
unsupported PHY interface type, instead it should stop.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any of sja1105_static_config_load(), sja1105_clocking_setup() or
sja1105_devlink_setup() fails, we can't just return in the middle of
sja1105_setup() or memory will leak. Add a cleanup path.
Fixes: 0a7bdbc23d ("net: dsa: sja1105: move devlink param code to sja1105_devlink.c")
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other drivers which pretty much end their .probe() execution with
dsa_register_switch(), the sja1105 does some extra stuff. When that
fails with -ENOMEM, the driver is quick to return that, forgetting to
call dsa_unregister_switch(). Not critical, but a bug nonetheless.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Fixes: a68578c20a ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of the sja1105_dynamic_config.c file there is a diagram
of the dynamic config interface layout:
packed_buf
|
V
+-----------------------------------------+------------------+
| ENTRY BUFFER | COMMAND BUFFER |
+-----------------------------------------+------------------+
<----------------------- packed_size ------------------------>
So in order to pack/unpack the command bits into the buffer,
sja1105_vl_lookup_cmd_packing must first advance the buffer pointer by
the length of the entry. This is similar to what the other *cmd_packing
functions do.
This bug exists because the command packing function for P/Q/R/S was
copied from the E/T generation, and on E/T, the command was actually
embedded within the entry buffer itself.
Fixes: 94f94d4acf ("net: dsa: sja1105: add static tables for virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify some fields of the USB descriptor to make sure the driver
could be used by the device.
Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.
BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943e3 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
- "cgroup_disable=" boot param was being applied too late confusing
some subsystems. Fix it by moving application to __setup() time.
- Comment spelling fixes. Included here to lower the chance of trivial
future merge conflicts.
* 'for-5.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix spelling mistakes
cgroup: disable controllers at parse time
Pull workqueue fix from Tejun Heo:
"One commit to fix spurious workqueue stall warnings across VM
suspensions"
* 'for-5.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
wq: handle VM suspension in stall detection
