The `clkin_rate' member of `struct sifive_serial_port' now duplicates
`uartclk' from nested `struct uart_port', so use `uartclk' throughout
and remove `clkin_rate'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656150.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
We currently drive the device using its default oversampling rate of 16
and the clock prescaler disabled, consequently yielding the baud base of
3906250. This base is inadequate for some of the high-speed baud rates
such as 460800bps, for which the closest rate possible can be obtained
by dividing the baud base by 8, yielding the baud rate of 488281.25bps,
which is off by 5.9638%. This is enough for data communication to break
with the remote end talking actual 460800bps, where missed stop bits
have been observed.
We can do better however, by taking advantage of a reduced oversampling
rate, which can be set to any integer value from 4 to 16 inclusive by
programming the TCR register, and by using the clock prescaler, which
can be set to any value from 1 to 63.875 in increments of 0.125 in the
CPR/CPR2 register pair. The prescaler has to be explicitly enabled
though by setting bit 7 in the MCR or otherwise it is bypassed (in the
enhanced mode that we enable) as if the value of 1 was used.
Make use of these features then as follows:
- Set the baud base to 15625000, reflecting the minimum oversampling
rate of 4 with the clock prescaler and divisor both set to 1.
- Override the `set_mctrl' and set the MCR shadow there so as to have
MCR[7] always set and have the 8250 core propagate these settings.
- Override the `get_divisor' handler and determine a good combination of
parameters by using a lookup table with predetermined value pairs of
the oversampling rate and the clock prescaler and finding a pair that
divides the input clock such that the quotient, when rounded to the
nearest integer, deviates the least from the exact result. Calculate
the clock divisor accordingly.
Scale the resulting oversampling rate (only by powers of two) if
possible so as to maximise it, reducing the divisor accordingly, and
avoid a divisor overflow for very low baud rates by scaling the
oversampling rate and/or the prescaler even if that causes some
accuracy loss.
Also handle the historic spd_cust feature so as to allow one to set
all the three parameters manually to arbitrary values, by keeping the
low 16 bits for the divisor and then putting TCR in bits 19:16 and
CPR/CPR2 in bits 28:20, sanitising the bit pattern supplied such as
to clamp CPR/CPR2 values between 0.000 and 0.875 inclusive to 33.875.
This preserves compatibility with any existing setups, that is where
requesting a custom divisor that only has any bits set among the low
16 the oversampling rate of 16 and the clock prescaler of 33.875 will
be used as with the original 8250.
Finally abuse the `frac' argument to store the determined bit patterns
for the TCR, CPR and CPR2 registers.
- Override the `set_divisor' handler so as to set the TCR, CPR and CPR2
registers from the `frac' value supplied. Set the divisor as usual.
With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
limitation imposed by `serial8250_get_baud_rate' standard baud rates
below 300bps become unavailable in the regular way, e.g. the rate of
200bps requires the baud base to be divided by 78125 and that is beyond
the unsigned 16-bit range. The historic spd_cust feature can still be
used to obtain such rates if so required.
See Documentation/tty/device_drivers/oxsemi-tornado.rst for more details.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181519450.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make ICR access helpers available outside 8250_port.c, however retain
them as ordinary static functions so as not to regress code generation.
This is because `serial_icr_write' is currently automatically inlined by
GCC, however `serial_icr_read' is not. Making them both static inline
would grow code produced, e.g.:
$ i386-linux-gnu-size --format=gnu 8250_port-{old,new}.o
text data bss total filename
15065 3378 0 18443 8250_port-old.o
15289 3378 0 18667 8250_port-new.o
and:
$ riscv64-linux-gnu-size --format=gnu 8250_port-{old,new}.o
text data bss total filename
16980 5306 0 22286 8250_port-old.o
17124 5306 0 22430 8250_port-new.o
while making them external would needlessly add a new module interface
and lose the benefit from `serial_icr_write' getting inlined outside
8250_port.o.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181517500.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and uses the same sequence to determine the
number of ports available. Despite that we have duplicate code
specific to the EndRun device.
Remove redundant code then and factor out OxSemi Tornado device
detection.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181516220.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 PXA driver never used Runtime PM, so there was never a need to
include <linux/pm_runtime.h>.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/9fd96fba9bbbbdeb16af0dc07ae9dee21c8e297c.1651494971.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_platform_data is only used on DT platforms for now.
Fixes: 4a218b277f ("serial: 8250: dw: Create a generic platform data structure")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220502115621.77985-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys DesignWare UART can be configured to have HW support for
the RS485 protocol from IP version 4.0 onward. Add support for
hardware-controlled half duplex and full duplex modes.
HW will take care of managing DE and RE, the driver just gives it
permission to use either by setting both to 1.
To ask for full duplex mode, userspace sets SER_RS485_RX_DURING_TX flag
and HW will take care of the rest.
Set delay_rts_before_send and delay_rts_after_send to zero for now. The
granularity of that ABI is too coarse to be useful.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UART_CAP_NOTEMT for UARTs that lack interrupt on TEMT but want to
use em485. Em485 framework needs to ensure not only FIFO is empty but
also that tx shift register is empty.
This approach uses Uwe Kleine-König's suggestion on simply
using/incrementing stop_tx timer rather than adding another timer. When
UART_CAP_NOTEMT is set and THRE is present w/o TEMT, stop tx timer is
reused to wait for the emptying of the shift register.
This change does not add the UART_CAP_NOTEMT define as it already exist
but is currently no-op. See 7a107b2c6b (Revert "serial: 8250: Handle
UART without interrupt on TEMT using em485") for further details.
Vicente Bergas reported that RTS is deasserted roughly one bit too
early losing stop bit tx. To address this problem, stop_delay now
accounts for one extra bit using rough formula /7 (assumes worst-case
of 2+5 bits). I suspect this glitch had to do with when THRE is getting
asserted. If FIFO is emptied already during the tx of the stop bit,
perhaps it leads to HW asserting THRE early for the normal frame time
formula to work accurately.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Eric Tremblay <etremblay@distech-controls.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 DMA tx complete path lacks calls to normal 8250 stop handling. It
does not use THRE to detect true completion of the tx and also doesn't
call __stop_tx. This leads to problems with em485 that needs to handle
RTS timing.
Instead of handling tx stop internally within 8250 dma code, enable
THRE when tx'able data runs out and tweak serial8250_handle_irq to call
only __stop_tx when uart is using DMA.
It also seems bit early to call serial8250_rpm_put_tx from there while
tx is still underway(?).
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct uart_port currently stores FIFO timeout. Having character timing
information readily available is useful. Even serial core itself
determines char_time from port->timeout using inverse calculation.
Store frame_time directly into uart_port. Character time is stored in
nanoseconds to have reasonable precision with high rates. To avoid
overflow, 64-bit math is necessary.
It might be possible to determine timeout from frame_time by
multiplying it with fifosize as needed but only part of the users seem
to be protected by a lock. Thus, this patch does not pursue storing
only frame_time in uart_port.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220425143410.12703-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas RZ/N1 SoC features a slightly modified DW UART.
On this SoC, the CPR register value is known but not synthetized in
hardware. We hence need to provide a CPR value in the platform
data. This version of the controller also relies on acting as flow
controller when using DMA, so we need to provide the
"is dma flow controller" quirk.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW based controllers like the one on Renesas RZ/N1 must be programmed as
flow controllers when using DMA.
* Table 11.45 of the system manual, "Flow Control Combinations", states
that using UART with DMA requires setting the DMA in the peripheral
flow controller mode regardless of the direction.
* Chapter 11.6.1.3 of the system manual, "Basic Interface Definitions",
explains that the burst size in the above case must be configured in
the peripheral's register DEST/SRC_BURST_SIZE.
Experiments shown that upon Rx timeout, the DMA transaction needed to be
manually cleared as well.
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These accessors should be used instead of the regular readl/writel()
helpers. In order to use them also from 8250_dw.c in this directory,
move the helpers to 8250_dwlib.h
There is no functional change.
There is no need for declaring `struct uart_port` or even UPIO_MEM32BE
which both are already included in the 8250_dwlib.h header by 8250.h.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a next change we are going to need the same Rx timeout condition as
we already have in the IRQ handling code. Let's just create a boolean to
clarify what this operation does before reusing it.
There is no functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One situation where this could be used is when configuring the UART
controller to be the DMA flow controller. This is a typical case where
the driver might need to program a few more registers before starting a
DMA transfer. Provide the necessary infrastructure to support this
case.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART controllers can be synthesized without the CPR register.
In this case, allow to the platform information to provide a CPR value.
Co-developed-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This offset is a good candidate to pdata's because it changes depending
on the vendor implementation. Let's move the usr_reg entry from regular
to pdata. This way we can drop initializing it at run time.
Let's also use a define for it instead of defining only the default
value.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use device tree match data rather than multiple calls to
of_device_is_compatible() by introducing a platform data structure and
adding a quirks mask.
Provide a stub to the compatibles without quirks to simplify the
handling of the upcoming changes.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
[<miquel.raynal@bootlin.com: Minor changes + creation of a real pdata structure]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the per-device structure and a helper out of the main .c file, into
a shared header as they will both be reused from another .c file.
There is no functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
[miquel.raynal@bootlin.com: Extracted from a bigger change]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422180615.9098-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use if and else instead of if(A) and if (!A).
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20220426071041.168282-1-wanjiabing@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fe ("tty: n_gsm: fix invalid use of MSC in advanced option")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23 ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dynamic virtual tty registration was introduced to allow the user to handle
these cases with uevent rules. The following commits relate to this:
Commit 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Commit 0b91b53323 ("tty: n_gsm: Save dlci address open status when config requester")
Commit 46292622ad ("tty: n_gsm: clean up indenting in gsm_queue()")
However, the following behavior can be seen with this implementation:
- n_gsm ldisc is activated via ioctl
- all configuration parameters are set to their default value (initiator=0)
- the mux gets activated and attached and gsmtty0 is being registered in
in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control
channel)
- the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator
- this re-attaches the n_gsm mux
- no new gsmtty devices are registered in gsmld_attach_gsm() because the
mux is already active
- the initiator side registered only the control channel as gsmtty0
(which should never happen) and no user channel tty
The commits above make it impossible to operate the initiator side as no
user channel tty is or will be available.
On the other hand, this behavior will make it also impossible to allow DLCI
parameter negotiation on responder side in the future. The responder side
first needs to provide a device for the application before the application
can set its parameters of the associated DLCI via ioctl.
Note that the user application is still able to detect a link establishment
without relaying to uevent by waiting for DTR open on responder side. This
is the same behavior as on a physical serial interface. And on initiator
side a tty hangup can be detected if a link establishment request failed.
Revert the commits above completely to always register all user channels
and no control channel after mux attachment. No other changes are made.
Fixes: 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 927728a34f.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for KGDB in stm32 serial driver by implementing characters
polling callbacks (poll_init, poll_get_char and poll_put_char).
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework stm32_usart_console_putchar() function in order to anticipate
the case where the character can never be sent.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not set timeout to twice the approximate amount of time to send the
entire FIFO if CTS is enabled. If the caller requested no timeout, e.g.
when userspace program called tcdrain(), then wait without any timeout.
Premature return from tcdrain() was observed on imx based system which
has 32 character long transmitter FIFO with hardware CTS handling.
Simple userspace application that reproduces problem has to:
* Open tty device, enable hardware flow control (CRTSCTS)
* Write data, e.g. 26 bytes
* Call tcdrain() to wait for the transmitter
* Close tty device
The other side of serial connection has to:
* Receive some data, e.g. 10 bytes
* Set RTS output (CTS input from sender perspective) inactive for
at least twice the port timeout
* Try to receive remaining data
Without this patch, userspace application will finish without any error
while the other side of connection will never receive remaining data.
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220228054911.1420221-1-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note: I am using a small test app + driver located at [0] for the
problem description. serco is a driver whose write function dispatches
to the serial controller. sertest is a user-mode app that writes n bytes
to the serial console using the serco driver.
While investigating a bug in the RHEL kernel, I noticed that the serial
console throughput is way below the configured speed of 115200 bps in
a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but
I got 2.5KB/s.
$ time ./sertest -n 2500 /tmp/serco
real 0m0.997s
user 0m0.000s
sys 0m0.997s
With the help of the function tracer, I then noticed the serial
controller was taking around 410us seconds to dispatch one single byte:
$ trace-cmd record -p function_graph -g serial8250_console_write \
./sertest -n 1 /tmp/serco
$ trace-cmd report
| serial8250_console_write() {
0.384 us | _raw_spin_lock_irqsave();
1.836 us | io_serial_in();
1.667 us | io_serial_out();
| uart_console_write() {
| serial8250_console_putchar() {
| wait_for_xmitr() {
1.870 us | io_serial_in();
2.238 us | }
1.737 us | io_serial_out();
4.318 us | }
4.675 us | }
| wait_for_xmitr() {
1.635 us | io_serial_in();
| __const_udelay() {
1.125 us | delay_tsc();
1.429 us | }
...
...
...
1.683 us | io_serial_in();
| __const_udelay() {
1.248 us | delay_tsc();
1.486 us | }
1.671 us | io_serial_in();
411.342 us | }
In another machine, I measured a throughput of 11.5KB/s, with the serial
controller taking between 80-90us to send each byte. That matches the
expected throughput for a configuration of 115200 bps.
This patch changes the serial8250_console_write to use the 16550 fifo
if available. In my benchmarks I got around 25% improvement in the slow
machine, and no performance penalty in the fast machine.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20220411174841.34936-2-wander@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of sysrq_key_table's elements, like sysrq_thaw_op and
sysrq_showallcpus_op are not consistent with sysrq_ftrace_dump_op,
Consistency makes code more readable.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Junwen Wu <wudaemon@gmail.com>
Link: https://lore.kernel.org/r/20220418153703.97705-1-wudaemon@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some more serial drivers can be compile-tested under certain
circumstances (when building a specific architecture). So allow for
that.
This reduces the need of zillion mach/subarch-specific configs. And
since the 0day bot has only allmodconfig's for some archs, this
increases build coverage there too.
Note that cpm needs a minor update in the header, so that it drags in
at least some defines (CPM2 ones).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pic32_uart contains this:
#ifdef CONFIG_SERIAL_PIC32_CONSOLE
...
console_initcall(pic32_console_init);
...
core_initcall(pic32_late_console_init);
...
#endif
...
arch_initcall(pic32_uart_init);
When the driver is built as module, all three above become
module_init(). So if SERIAL_PIC32_CONSOLE is set while SERIAL_PIC32=m,
it results in the following build error:
In file included from include/linux/device/driver.h:21,
from include/linux/device.h:32,
from include/linux/platform_device.h:13,
from drivers/tty/serial/pic32_uart.c:12:
include/linux/module.h:131:49: error: redefinition of '__inittest'
So make sure SERIAL_PIC32_CONSOLE can be set only when SERIAL_PIC32=y --
similar as for other drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code wants to know if the circ buffer is empty, so use the proper
macro.
No functional change intended, just saner function name used for that
use case.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_port::membase is declared as a pointer. So it should be
initialized by NULL, not zero constant.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cache port->state->xmit into a local variable (xmit) in
cdns_uart_handle_tx(). This reduces length of some lines there
significantly. I.e. makes the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return from the true branch of the 'if'. This saves one indentation
level and makes the code more readable.
The two comments about what obvious code does are removed too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports this issue
sunplus-uart.c:501:26: warning: symbol 'sunplus_console_ports' was not declared. Should it be static?
sunplus_console_ports is only used in sunplus-uart.c so change
its storage-class specifier to static
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220421152505.1531507-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
