Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add HDMI support. As the DDC I2C pins are not connected due to
pin conflicts, we do not pass the 'ddc-i2c-bus' property in
this case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pinctrl-assert-gpios is an invalid pinctrl property. It was
probably sneaked from vendor tree. Remove it.
Fixes: 4e18a2243a ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The D9 LED controlled by gpio on the imx6qdl-sabreauto
CPU board is a debug LED according to the board design.
This patch adds the relevant device tree nodes to the
imx6qdl-sabreauto device tree file to support this LED.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6 sabreauto boards have Freescale PFUZE100 regulator, so add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds spdif support for imx6qdl-sabreauto by inserting the cpu dai
node with pinctrl group and its ASoC dai link node.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the WEIM NOR for imx6q{dl}-sabreauto boards.
For the pin conflict with SPI NOR, its status is set to "disabled".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The sabreauto and sabresd boards are common for imx6q and imx6dl.
Create imx6qdl-sabreauto.dtsi and imx6qdl-sabresd.dtsi for those
common parts.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
