The fields for the number of rows and columns in the encode frame
response message are switched. This causes broken PPS, if the encoder
uses tiles for encoding and the number of rows and columns differ.
Write the fields of the response message into the correct fields of the
the internal data structure when parsing the response message.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The encoder buffer can have a negative impact on the quality of the
encoded video.
Add a control to allow user space to disable the encoder buffer per
channel if the VCU supports the encoder buffer but the quality is not
sufficient.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The encoder buffer serves as a cache for reference frames during the
encoding process. The encoder buffer significantly reduces the bandwidth
requirement for read accesses on the AXI ports of the VCU, but slightly
reduces the quality of the encoded video.
The encoder buffer must be configured as a whole during the firmware
initialization and later explicitly enabled for every channel that shall
use the encoder buffer.
Prior to firmware version 2019.2, it was necessary to explicitly set the
size of the encoder buffer for every channel. Since 2019.2 it is
sufficient to enable the encoder buffer and leave the rest to the
firmware. Therefore, only support the encoder buffer for firmware 2019.2
and later.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The allegro driver must ensure that the mcu and core clocks are enabled
and set to the expected clock rate before trying to load the firmware
and to reset the MCU.
Up until now, the driver assumed that the clocks are always enabled in
the PL (programming logic), because the xlnx_vcu driver did not export
the clocks to other drivers. This has changed and by explicitly enabling
the clocks in the driver, this assumption can be dropped.
It might even be possible to disable the clocks for the encoder if the
encoder is not used. However, the behavior is not documented and it
might be necessary to reinitialize the encoder after deactivating the
clocks. Play it safe by sticking to the current behavior.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VCU provides information about its configuration in a dedicated
register space. These settings include, for example, the expected clock
rates and the configuration of the encoder buffer. In the device tree,
the settings are described by the "xlnx,vcu-settings" compatible.
The settings are needed to correctly configure the clocks and the
encoder buffer.
Lookup the VCU settings in the device tree and make it accessible to the
driver via a regmap.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the module probe finished, but the firmware initialization failed,
removing the module must not revert the firmware initialization.
Add a field to track the status of the firmware initialization and only
roll it back, if the firmware was successfully initialized.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mailbox is initialized after the interrupt handler is installed. As
the firmware is loaded and started even later, it should not happen that
the interrupt occurs without the mailbox being initialized.
As the Linux Driver Verification project (linuxtesting.org) keeps
reporting this as an error, add a check to ignore interrupts before the
mailbox is initialized to fix this potential null pointer dereference.
Reported-by: Yuri Savinykh <s02190703@gse.cs.msu.ru>
Reported-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Save some power by disabling/enabling the jpeg clocks with
every stream stop/start.
Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains,
to ensure power domains are off after probe.
Signed-off-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver
supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2
receiver and VIN and filters the CSI-2 data based on VC/DT and directs
the video stream to different VIN IPs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Get the min buffer count required by FW from source event change
and use the same value to decide actual buffer count and for
buffer size calculation.
- Setup DPB and OPB buffers after session continue incase of
reconfig.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set work route to FW based on num of vpp pipes.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
AON register programming is used to set NOC to low power mode
during V6 power off sequence. However AON register memory map
is not applicable to 1pipe, hence skipping AON register programming.
Co-developed-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Co-developed-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V6 HW can have vpp pipes as 1 or 4, add num_vpp_pipes
to resource struture to differentiate.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In existing video driver implementation vpp frequency calculation in
calculate_inst_freq() is always zero because the value of vpp_freq_per_mb
is always zero for decoder.
Fixed this by correcting the calculating the vpp frequency calculation for
decoder.
Fixes: 3cfe5815ce ("media: venus: Enable low power setting for encoder")
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video driver maintains an internal context for the output buffer size.
During S_fmt() on capture plane, the output buffer size is not updated
in driver context. As a result, during buf_prepare(), the size of the
vb2_plane and internal size of the buffer, as maintained by the driver,
does not match. This leads to buf_prepare() failure.
Update the instance context for the output buffer size during s_fmt().
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In current video driver implementation in calculate_inst_freq()
frequency is calculated based on filled_len. The filled_len may
vary frame to frame, because of this in load_scale_v4() since
frequency is calculated for all instances, driver is throwing
false warning like "HW is overloaded".
Hence to handle this, changed log level to low log message. Since the
actual session rejection is happening in decide_core() based on
load.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
gcc notices that the driver mixes 'dma_addr_t' 'u8 *' and 'u32'
to store DMA addresses:
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_vb2_prepare':
drivers/media/platform/omap/omap_vout.c:979:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->queued_buf_addr[vb->index] = (u8 *)buf_phy_addr;
^
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_create_video_devices':
drivers/media/platform/omap/omap_vout.c:1479:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
vout->fbuf.base = (void *)info.paddr;
Use dma_addr_t everywhere here to avoid the type conversions and document
what the address is used for. Assigning to vout->fbuf.base still requires
a cast, since that is part of the driver independent data structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V3U provides two VSPD instances, with a new update to the version
register to detect the new SoC.
Add the new version and model detection, and detail the features
available in this module.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In commit 6732f31393 ("media: v4l: vsp1: Fix uif null pointer access")
the handling of the UIF was over complicated, and the patch applied
before review.
Simplify it to keep the conditionals small.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The WPF IRQ enable and status macros have been incorrectly named WFP.
Fix them accordingly, and update all uses of the macros.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove soft reset between frames, which was merely a workaround,
actually replace it with something less aggressive: clearing of jpeg stream
buffer pointer, via STM_CTRL[BITBUF_PTR_CLR].
According to the reference manual, the BITBUF_PTR_CLR is performed on
context switch, but, per hardware team recommendation, it is also working
without context switch, which is the case for this driver, for now.
Without soft reset and without BITBUF_PTR_CLR, successive encoding jobs
continue from where the previous left off, basically writing past the
v4l2 buffer.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add some body to the dummy jpeg used to inject a default DHT.
Use jpeg_image_red as compressed image data, insert it at the
end of SOS, before EOI.
The pure dummy jpeg was occasionally not working well on
8qxp C0.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set recommend min/max bitrate range for MT8173 h264/vp8 encoder.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The access to the internal storage of the format rcar_csi2.mf should be
serialized, extend the existing lock mutex to also cover this.
While at it document the mutex.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The switch of jpeg 420/444 subsampling will update full jpeg header for
aspeed now.
Just update the 420/444 subsampling part of jpeg header is fine.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of a macro named 'RST' conflicts with one of the same name
in arch/mips/include/asm/mach-rc32434/rb.h. This causes build
warnings on some MIPS builds.
Change the names of the JPEG marker constants to be in their own
namespace to fix these build warnings and to prevent other similar
problems in the future.
Fixes these build warnings:
In file included from ../drivers/media/platform/s5p-jpeg/jpeg-hw-exynos3250.c:14:
../drivers/media/platform/s5p-jpeg/jpeg-core.h:43: warning: "RST" redefined
43 | #define RST 0xd0
|
../arch/mips/include/asm/mach-rc32434/rb.h:13: note: this is the location of the previous definition
13 | #define RST (1 << 15)
In file included from ../drivers/media/platform/s5p-jpeg/jpeg-hw-s5p.c:13:
../drivers/media/platform/s5p-jpeg/jpeg-core.h:43: warning: "RST" redefined
43 | #define RST 0xd0
../arch/mips/include/asm/mach-rc32434/rb.h:13: note: this is the location of the previous definition
13 | #define RST (1 << 15)
In file included from ../drivers/media/platform/s5p-jpeg/jpeg-hw-exynos4.c:12:
../drivers/media/platform/s5p-jpeg/jpeg-core.h:43: warning: "RST" redefined
43 | #define RST 0xd0
../arch/mips/include/asm/mach-rc32434/rb.h:13: note: this is the location of the previous definition
13 | #define RST (1 << 15)
In file included from ../drivers/media/platform/s5p-jpeg/jpeg-core.c:31:
../drivers/media/platform/s5p-jpeg/jpeg-core.h:43: warning: "RST" redefined
43 | #define RST 0xd0
../arch/mips/include/asm/mach-rc32434/rb.h:13: note: this is the location of the previous definition
13 | #define RST (1 << 15)
Also update the kernel-doc so that the word "marker" is not
repeated.
Link: https://lore.kernel.org/linux-media/20210907044022.30602-1-rdunlap@infradead.org
Fixes: bb677f3ac4 ("[media] Exynos4 JPEG codec v4l2 driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The runtime enabling of the ISPCK (internally clocks the pipeline inside
the ISC) has to be done after the pm_runtime for the ISC dev has been
started.
After the commit by Mauro:
the ISC failed to probe with the error:
atmel-sama5d2-isc f0008000.isc: failed to enable ispck: -13
atmel-sama5d2-isc: probe of f0008000.isc failed with error -13
This is because the enabling of the ispck is done too early in the probe,
and the PM runtime returns invalid request.
Thus, moved this clock enabling after pm_runtime_idle is called.
The ISPCK is required only for sama5d2 type of ISC.
Thus, add a bool inside the isc struct that is platform dependent.
For the sama7g5-isc, the enabling of the ISPCK is wrong and does not make
sense. Removed it from the sama7g5 probe. In sama7g5-isc, there is only
one clock, the MCK, which also clocks the internal pipeline of the ISC.
Adapted the clk_prepare and clk_unprepare to request the runtime PM
for both clocks (MCK and ISPCK) in case of sama5d2-isc, and the single
clock (MCK) in case of sama7g5-isc.
Fixes: dd97908ee3 ("media: atmel: properly get pm_runtime")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Without this, I see a randconfig link failure:
aarch64-linux-ld: drivers/media/platform/rcar_drif.o: in function `rcar_drif_remove':
rcar_drif.c:(.text+0x2a8): undefined reference to `v4l2_async_notifier_unregister'
aarch64-linux-ld: rcar_drif.c:(.text+0x2b0): undefined reference to `v4l2_async_notifier_cleanup'
aarch64-linux-ld: drivers/media/platform/rcar_drif.o: in function `rcar_drif_sdr_probe':
rcar_drif.c:(.text+0x1444): undefined reference to `v4l2_async_notifier_init'
aarch64-linux-ld: rcar_drif.c:(.text+0x14a0): undefined reference to `v4l2_async_notifier_register'
aarch64-linux-ld: rcar_drif.c:(.text+0x14d8): undefined reference to `v4l2_async_notifier_cleanup'
aarch64-linux-ld: rcar_drif.c:(.text+0x15a8): undefined reference to `__v4l2_async_notifier_add_fwnode_subdev'
I could not easily figure out when this was introduced, as this code
has not changed in a while but I only saw the problem recently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When adding an internal scratch buffer to improve buffer handling when
stopping it was also erroneously used when syncing at capture start.
This led to that the first three buffers captured were always dropped
as they were captured in the scratch buffer instead of in a buffer
provided by the user.
Allow the hardware to be given user provided buffers when preparing for
capture in the stopped state. This still allows the driver to sync with
the hardware and always completes the buffers to user-space in the
correct order as no buffers are completed before the sync is complete.
This change improves the driver as buffers are completed and given to
the user three frames earlier than before.
The change also fixes a warning produced by v4l2-compliance,
warn: v4l2-test-buffers.cpp(448): got sequence number 3, expected 0
[hverkuil: fixed some typos in the Subject and the log message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously it was possible, but a recent fix for uninitialized
`ret` variable broke this behavior.
v4l2_fh_is_singular_file() check is there just to determine
whether the power needs to be enabled, and it's not a failure
if it returns false.
Fixes: ba9139116b ("media: sun6i-csi: add a missing return code")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vfe->ops->hw_version(vfe) is being called before vfe->base has been
assigned, and before the hardware has been powered up.
Fixes: b10b5334528a9 ("media: camss: vfe: Don't read hardware version needlessly")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A successful 'mxc_jpeg_attach_pm_domains()' call should be balanced by a
corresponding 'mxc_jpeg_detach_pm_domains()' call in the error handling
path of the probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
Update the error handling path accordingly.
Fixes: 3003a180ef ("[media] VPU: mediatek: support Mediatek VPU")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Static analysis reports this representative problem
camss-vfe-4-1.c:333: The result of the left shift is undefined because
the left operand is negative
reg |= (height - 1) << 4;
~~~~~~~~~ ^
The is a false positive. height is set in vfe_get_wm_sizes() which
has a switch statement without a default.
Reviewing the switch, the cases contain redundant assignments.
So simplify to assignments.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If of_device_get_match_data() return NULL,
then null pointer dereference occurs in s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As partially addressed in commit 65d270acb2 ("media: aspeed: clear
garbage interrupts"), the ASpeed video engine sometimes asserts
interrupts that the driver hasn't enabled. In addition to the
CAPTURE_COMPLETE and FRAME_COMPLETE interrupts dealt with in that
patch, COMP_READY has also been observed. Instead of playing
whack-a-mole with each one individually, we can instead just blanket
ignore everything we haven't explicitly enabled.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Lei YU <yulei.sh@bytedance.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Macros should not use a trailing semicolon，and it was used
the semicolon after macro cam_dbg called in viacam_vb2_prepare,
so deleted these redundant semicolons.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case vb2ops_venc_start_streaming fails, the error value
is overwritten by the ret value of pm_runtime_put which might
be 0. Fix it.
Fixes: 985c73693f (" media: mtk-vcodec: Separating mtk encoder driver")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
