of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240307114348.3643034-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously, during the MSDC calibration process, a full clock cycle
actually not be covered, which in some cases didn't yield the best
results and could cause CRC errors. This problem is particularly
evident when MSDC is used as an SDIO host. In fact, MSDC support
tuning up to a maximum of 64 steps, but by default, the step number
is 32. By increase the tuning step, we are more likely to cover more
parts of a clock cycle, and get better calibration result.
To illustrate, when tuning 32 steps, if the obtained window has a hole
near the middle, like this: 0xffc07ff (hex), then the selected delay
will be the 6 (counting from right to left).
(32 <- 1)
1111 1111 1100 0000 0000 0111 11(1)1 1111
However, if we tune 64 steps, the window obtained may look like this:
0xfffffffffffc07ff. The final selected delay will be 44, which is
safer as it is further away from the hole:
(64 <- 1)
1111 ... (1)111 1111 1111 1111 1111 1100 0000 0000 0111 1111 1111
In this case, delay 6 selected through 32 steps tuning is obviously
not optimal, and this delay is closer to the hole, using it would
easily cause CRC problems.
As per mesaurements taken on mediatek SoC platform, the tuning phase
will take:
eMMC - 32 steps: ~3ms
- 64 steps: ~6ms
SDIO - 32 steps: ~4ms
- 64 steos: ~7ms
Tuning more steps won't prolong boot times by any meaningful amount
of time, so for SD/SDIO the default tuning steps will be adjust to
64. But for eMMC, it is still preferred to use 32 steps tuning as
otherwise there would be performance lose when accessing the RPMB
partition(requiring retuning each time).
You can configure property "mediatek,tuning-step" in MSDC dts node
to adjust the step number.
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231207063535.29546-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This log message is necessary for debugging, so enable it by default to
debug issues that are hard to reproduce locally.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231201102747.3854573-1-treapking@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230727070051.17778-5-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230718143054.1065288-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.4-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.5.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 208489032b ("mmc: mediatek: Add Mediatek MMC driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-4-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQHCI_SSC1 indicates to CQE the polling period to use when using periodic
SEND_QUEUE_STATUS(CMD13) polling.
Since MSDC CQE uses msdc_hclk as ITCFVAL, so driver should use hclk
frequency to get the actual time.
The default value 0x1000 that corresponds to 150us for MediaTek SoCs, let's
decrease it to 0x40 that corresponds to 2.35us, which can improve the
performance of some eMMC devices.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230609101355.5220-2-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When I boot a kukui-kodama board, I see an ugly warning in my kernel
log:
mtk-msdc 11240000.mmc: error -ENXIO: IRQ sdio_wakeup not found
It's pretty normal not to have an "sdio_wakeup" IRQ defined. In fact,
no device trees in mainline seem to have it. Let's use the
platform_get_irq_byname_optional() to avoid the error message.
Fixes: 527f36f5ef ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230510064434.1.I935404c5396e6bf952e99bb7ffb744c6f7fd430b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace code with the already defined function. No functional changes.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221124080031.14690-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add crypto clock control and ungate it before CQHCI init.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221106033924.9854-2-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adding mt7986 own characteristics and of_device_id to have support
of MT7986 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221025132953.81286-7-linux@fw-web.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clk_disable_unprepare() should be called in the error handling
of devm_clk_bulk_get_optional, fix it by replacing devm_clk_get_optional
and clk_prepare_enable by devm_clk_get_optional_enabled.
Fixes: f5eccd94b6 ("mmc: mediatek: Add subsys clock control for MT8192 msdc")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221125090141.3626747-1-cuigaosheng1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both of_device_id compatible strings and platform data were partially
ordered by name. Fix the ordering.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220915120923.86038-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we don't clear MSDC interrupts when cqe off/disable, which led
to the data complete interrupt will be reserved for the next command.
If the next command with data transfer after cqe off/disable, we process
the CMD ready interrupt and trigger DMA start for data, but the data
complete interrupt is already exists, then SW assume that the data transfer
is complete, SW will trigger DMA stop, but the data may not be transmitted
yet or is transmitting, so we may encounter the following error:
mtk-msdc 11230000.mmc: CMD bus busy detected.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220728080048.21336-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MediaTek IP requires that after dma stop, it need to wait this dma stop
bit auto-reset to 0. When bus is in high loading state, it will take a
while for the dma stop complete. If there is no waiting operation here,
when program runs to clear fifo and reset, bus will hang.
In addition, there should be no return in msdc_data_xfer_next() if
there is data need be transferred, because no matter what error occurs
here, it should continue to excute to the following mmc_request_done.
Otherwise the core layer may wait complete forever.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220609112239.18911-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make it unambiguous that the hw_reset callback is for cards and not
for controllers, we add 'card' to the callback name and convert all
users in one go. We keep the argument as mmc_host, though, because the
callback is used very early when mmc_card is not yet populated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220408080045.6497-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints the following log everytime data is written to RPMB:
mtk-msdc 11230000.mmc: phase: [map:ffffffff] [maxlen:32] [final:10]
dev_info is used to print that log but it seems that log is only
useful for debbuging. Use dev_dbg instead of dev_info.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220311103320.3072171-1-abailon@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 3c1a884436 ("mmc: mediatek: add support of source_cg clock")
an independent cg was introduced to avoid a hardware hang issue during
clock mode switches (subsequent commits will set that clock as optional).
When this clock is not present in device-tree, any operation is being
done on src_clk's parent (calling clk_get_parent()): to simplify this
and avoid checking for src_clk_cg presence everytime, just assign the
parent clock to src_clk_cg and remove the now useless checks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get an error during probe of an optional clock with function
devm_clk_get_optional(), this means that the clock was provided, but
an error occurred: this has to be escalated to the probe function
for the driver probe to fail accordingly, or unexpected hardware
behavior may happen.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver was unconditionally enabling support for SDIO mode,
but we do have a generic "no-sdio" DT parameter that sets caps2
MMC_CAP2_NO_SDIO.
Modify the HW initialization sequence to enable SDIO support only
if it hasn't been explicitly disabled in device-tree.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register fields are currently represented with open-coded bit
shifting: replace all occurrences of that to make use of kernel
provided macros BIT and GENMASK to increase human readability.
This patch provides no functional change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace all instances of open-coded while loops for polling registers
with calls to readl_poll_timeout() and, while at it, also fix some
possible infinite loop instances.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must enable clock before cqhci init, because crypto needs read
information from CQHCI registers, otherwise, it will hang in MediaTek mmc
host controller.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Acked-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20211028022049.22129-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.
In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases. But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_request structure(*mrq) is not used. //msdc_cmd_find_resp
I remove the unnecessary code related to the mmc_request structure.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20210827093119.32481-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'mrq->data' before calling these two functions, no
need to find it again via 'mrq->data' internally. Also remove local
data variable accordingly.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210517100900.1620-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac5 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDIO recheck fix is required for more of the supported variants. Let's
add it to those that needs it.
Reported-by: Fabien Parent <fparent@baylibre.com>
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/20201119030237.9414-1-yong.mao@mediatek.com
Fixes: 9e2582e574 ("mmc: mediatek: fix SDIO irq issue")
Cc: stable@vger.kernel.org
[Ulf: Clarified commitmsg ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It should use mmc_free_host to free mem in error patch of
msdc_drv_probe.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201112092530.32446-1-zhengliang6@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8192 msdc is an independent sub system, we need control more bus
clocks for it.
Add support for the additional subsys clocks to allow it to be
configured appropriately.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20201014030846.12428-5-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MediaTek MMC driver uses pointer to get from private
msdc_host structure to the generic mmc_host structure.
However mmc_host always precedes msdc_host in memory so compute
its address with a subtraction (which is cheaper than a dereference)
using mmc_from_priv() and drop the extra pointer.
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Link: https://lore.kernel.org/r/20200917192624.548720-1-ameynarkhede03@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQHCI_ENABLE bit in CQHCI_CFG should be disabled
after msdc_cqe_disable(), and should be enabled before
msdc_ceq_enable() for MTK platform.
Add hook functions for cqhci_host_ops->pre_enable() and
cqhci_host_ops->post_disable().
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
