The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.
Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.
Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
