Switch to tab-delimited output from fixed-width columns
to make it simpler to import into spreadsheets.
As the fixed width columnns were 8-spaces wide,
the output on the screen should not change.
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat gives valid results across suspend to idle, aka freeze,
whether invoked in interval mode, or in command mode.
Indeed, this can be used to measure suspend to idle:
turbostat echo freeze > /sys/power/state
But this does not work across suspend to ACPI S3, because the
processor counters, including the TSC, are reset on resume.
Further, when turbostat detects a problem, it does't forgive
the hardware, and interval mode will print *'s from there on out.
Instead, upon detecting counters going backwards, simply
reset and start over.
Interval mode across ACPI S3: (observe TSC going backwards)
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 1 0.06 858 2294 0x0000000000000000
0 0 0.06 847 2294 0x0000002a254b98ac
1 1 0.06 878 2294 0x0000002a254efa3a
2 1 0.07 843 2294 0x0000002a2551df65
3 0 0.05 863 2294 0x0000002a2553fea2
turbostat: re-initialized with num_cpus 4
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 2 0.20 849 2294 0x0000000000000000
0 2 0.26 856 2294 0x0000000449abb60d
1 2 0.20 844 2294 0x0000000449b087ec
2 2 0.21 850 2294 0x0000000449b35d5d
3 1 0.12 839 2294 0x0000000449b5fd5a
^C
Command mode across ACPI S3:
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10 sleep 10
./turbostat: Counter reset detected
14.196299 sec
Signed-off-by: Len Brown <len.brown@intel.com>
The RAPL Joules counter is limited in capacity.
Turbostat estimates how soon it can roll-over
based on the max TDP of the processor --
which tells us the maximum increment rate.
eg.
RAPL: 2759 sec. Joule Counter Range, at 95 Watts
So if a sample duration is longer than 2759 seconds on this system,
'**' replace the decimal place in the display to indicate
that the results may be suspect.
But the display had an extra ' ' in this case, throwing off the columns.
Also, the -J "Joules" option appended an extra "time" column
to the display. While this may be useful, it printed the interval time,
which may not be the accurate time per processor. Remove this column,
which appeared only when using '-J',
as we plan to add accurate per-cpu interval times in a future commit.
Signed-off-by: Len Brown <len.brown@intel.com>
This is a test to verify that
bpf: fix states equal logic for varlen access
actually fixed the problem. The problem was if the register we added to our map
register was UNKNOWN in both the false and true branches and the only thing that
changed was the range then we'd incorrectly assume that the true branch was
valid, which it really wasnt. This tests this case and properly fails without
my fix in place and passes with it in place.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Link: http://lkml.kernel.org/r/1480372524-15181-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Track freed memory as well as allocations and show the net in the
summary.
Committer notes:
Testing it:
# perf kmem record usleep 1
[ perf record: Woken up 0 times to write data ]
[ perf record: Captured and wrote 1.626 MB perf.data (4208 samples) ]
[root@jouet ~]# perf kmem stat --slab
SUMMARY (SLAB allocator)
========================
Total bytes requested: 234,011
Total bytes allocated: 234,504
Total bytes freed: 213,328 <------
Net total bytes allocated: 21,176
Total bytes wasted on internal fragmentation: 493
Internal fragmentation: 0.210231%
Cross CPU allocations: 4/1,963
#
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1480110133-37039-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Having "test" in almost all test descriptions is redundant, simplify it
removing and rewriting tests with such descriptions.
End result:
# perf test
1: vmlinux symtab matches kallsyms : Ok
2: Detect openat syscall event : Ok
3: Detect openat syscall event on all cpus : Ok
4: Read samples using the mmap interface : Ok
5: Parse event definition strings : Ok
6: PERF_RECORD_* events & perf_sample fields : Ok
7: Parse perf pmu format : Ok
8: DSO data read : Ok
9: DSO data cache : Ok
10: DSO data reopen : Ok
11: Roundtrip evsel->name : Ok
12: Parse sched tracepoints fields : Ok
13: syscalls:sys_enter_openat event fields : Ok
14: Setup struct perf_event_attr : Ok
15: Match and link multiple hists : Ok
16: 'import perf' in python : Ok
17: Breakpoint overflow signal handler : Ok
18: Breakpoint overflow sampling : Ok
19: Number of exit events of a simple workload : Ok
20: Software clock events period values : Ok
21: Object code reading : Ok
22: Sample parsing : Ok
23: Use a dummy software event to keep tracking: Ok
24: Parse with no sample_id_all bit set : Ok
25: Filter hist entries : Ok
26: Lookup mmap thread : Ok
27: Share thread mg : Ok
28: Sort output of hist entries : Ok
29: Cumulate child hist entries : Ok
30: Track with sched_switch : Ok
31: Filter fds with revents mask in a fdarray : Ok
32: Add fd to a fdarray, making it autogrow : Ok
33: kmod_path__parse : Ok
34: Thread map : Ok
35: LLVM search and compile :
35.1: Basic BPF llvm compile : Ok
35.2: kbuild searching : Ok
35.3: Compile source for BPF prologue generation: Ok
35.4: Compile source for BPF relocation : Ok
36: Session topology : Ok
37: BPF filter :
37.1: Basic BPF filtering : Ok
37.2: BPF prologue generation : Ok
37.3: BPF relocation checker : Ok
38: Synthesize thread map : Ok
39: Synthesize cpu map : Ok
40: Synthesize stat config : Ok
41: Synthesize stat : Ok
42: Synthesize stat round : Ok
43: Synthesize attr update : Ok
44: Event times : Ok
45: Read backward ring buffer : Ok
46: Print cpu map : Ok
47: Probe SDT events : Ok
48: is_printable_array : Ok
49: Print bitmap : Ok
50: perf hooks : Ok
51: x86 rdpmc : Ok
52: Convert perf time to TSC : Ok
53: DWARF unwind : Ok
54: x86 instruction decoder - new instructions : Ok
55: Intel cqm nmi context read : Skip
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-rx2lbfcrrio2yx1fxcljqy0e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Perf hooks allow hooking user code at perf events. They can be used for
manipulation of BPF maps, taking snapshot and reporting results. In this
patch two perf hook points are introduced: record_start and record_end.
To avoid buggy user actions, a SIGSEGV signal handler is introduced into
'perf record'. It turns off perf hook if it causes a segfault and report
an error to help debugging.
A test case for perf hook is introduced.
Test result:
$ ./buildperf/perf test -v hook
50: Test perf hooks :
--- start ---
test child forked, pid 10311
SIGSEGV is observed as expected, try to recover.
Fatal error (SEGFAULT) in perf hook 'test'
test child finished with 0
---- end ----
Test perf hooks: Ok
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Stringer <joe@ovn.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161126070354.141764-5-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a new API to libbpf, caller is able to get bpf_map through the
offset of bpf_map_def to 'maps' section.
The API will be used to help jitted perf hook code find fd of a map.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Stringer <joe@ovn.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161126070354.141764-4-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Similar to other classes defined in libbpf.h (map and program), allow
'object' class has its own private data.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: He Kuang <hekuang@huawei.com>
Cc: Joe Stringer <joe@ovn.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161126070354.141764-3-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add more BPF map operations to libbpf. Also add bpf_obj_{pin,get}(). They
can be used on not only BPF maps but also BPF programs.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: He Kuang <hekuang@huawei.com>
Cc: Joe Stringer <joe@ovn.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161126070354.141764-2-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
1) The test_lru_map and test_lru_dist fails building on my machine since
the sys/resource.h header is not included.
2) test_verifier fails in one test case where we try to call an invalid
function, since the verifier log output changed wrt printing function
names.
3) Current selftest suite code relies on sysconf(_SC_NPROCESSORS_CONF) for
retrieving the number of possible CPUs. This is broken at least in our
scenario and really just doesn't work.
glibc tries a number of things for retrieving _SC_NPROCESSORS_CONF.
First it tries equivalent of /sys/devices/system/cpu/cpu[0-9]* | wc -l,
if that fails, depending on the config, it either tries to count CPUs
in /proc/cpuinfo, or returns the _SC_NPROCESSORS_ONLN value instead.
If /proc/cpuinfo has some issue, it returns just 1 worst case. This
oddity is nothing new [1], but semantics/behaviour seems to be settled.
_SC_NPROCESSORS_ONLN will parse /sys/devices/system/cpu/online, if
that fails it looks into /proc/stat for cpuX entries, and if also that
fails for some reason, /proc/cpuinfo is consulted (and returning 1 if
unlikely all breaks down).
While that might match num_possible_cpus() from the kernel in some
cases, it's really not guaranteed with CPU hotplugging, and can result
in a buffer overflow since the array in user space could have too few
number of slots, and on perpcu map lookup, the kernel will write beyond
that memory of the value buffer.
William Tu reported such mismatches:
[...] The fact that sysconf(_SC_NPROCESSORS_CONF) != num_possible_cpu()
happens when CPU hotadd is enabled. For example, in Fusion when
setting vcpu.hotadd = "TRUE" or in KVM, setting ./qemu-system-x86_64
-smp 2, maxcpus=4 ... the num_possible_cpu() will be 4 and sysconf()
will be 2 [2]. [...]
Documentation/cputopology.txt says /sys/devices/system/cpu/possible
outputs cpu_possible_mask. That is the same as in num_possible_cpus(),
so first step would be to fix the _SC_NPROCESSORS_CONF calls with our
own implementation. Later, we could add support to bpf(2) for passing
a mask via CPU_SET(3), for example, to just select a subset of CPUs.
BPF samples code needs this fix as well (at least so that people stop
copying this). Thus, define bpf_num_possible_cpus() once in selftests
and import it from there for the sample code to avoid duplicating it.
The remaining sysconf(_SC_NPROCESSORS_CONF) in samples are unrelated.
After all three issues are fixed, the test suite runs fine again:
# make run_tests | grep self
selftests: test_verifier [PASS]
selftests: test_maps [PASS]
selftests: test_lru_map [PASS]
selftests: test_kmod.sh [PASS]
[1] https://www.sourceware.org/ml/libc-alpha/2011-06/msg00079.html
[2] https://www.mail-archive.com/netdev@vger.kernel.org/msg121183.html
Fixes: 3059303f59 ("samples/bpf: update tracex[23] examples to use per-cpu maps")
Fixes: 86af8b4191 ("Add sample for adding simple drop program to link")
Fixes: df570f5772 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_ARRAY")
Fixes: e155967179 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_HASH")
Fixes: ebb676daa1 ("bpf: Print function name in addition to function id")
Fixes: 5db58faf98 ("bpf: Add tests for the LRU bpf_htab")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handlers for sched:sched_migrate_task event. Total number of
migrations is added to summary display and -M/--migrations can be used
to show migration events.
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1480091321-35591-1-git-send-email-dsa@cumulusnetworks.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To help in debugging when the wrong offset is being used, like in:
│13d98: ↓ jne 13dd1 <lzma_lzma_preset@@XZ_5.0+0x28e1>
That is the full line from objdump, and it seems what should be used is
13dd1, not 28e1.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-4nc0marsgst1ft6inmvqber7@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To print some values, like in the annotation code with invalid jump
offsets.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-1vk0g5twas2ioswn1mmvnvwq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is not correct to assimilate the elf data of the maps section to an
array of map definition. In fact the sizes differ. The offset provided
in the symbol section has to be used instead.
This patch fixes a bug causing a elf with two maps not to load
correctly.
Wang Nan added:
This patch requires a name for each BPF map, so array of BPF maps is not
allowed. This restriction is reasonable, because kernel verifier forbid
indexing BPF map from such array unless the index is a fixed value, but
if the index is fixed why not merging it into name?
For example:
Program like this:
...
unsigned long cpu = get_smp_processor_id();
int *pval = map_lookup_elem(&map_array[cpu], &key);
...
Generates bytecode like this:
0: (b7) r1 = 0
1: (63) *(u32 *)(r10 -4) = r1
2: (b7) r1 = 680997
3: (63) *(u32 *)(r10 -8) = r1
4: (85) call 8
5: (67) r0 <<= 4
6: (18) r1 = 0x112dd000
8: (0f) r0 += r1
9: (bf) r2 = r10
10: (07) r2 += -4
11: (bf) r1 = r0
12: (85) call 1
Where instruction 8 is the computation, 8 and 11 render r1 to an invalid
value for function map_lookup_elem, causes verifier report error.
Signed-off-by: Eric Leblond <eric@regit.org>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Wang Nan <wangnan0@huawei.com>
[ Merge bpf_object__init_maps_name into bpf_object__init_maps.
Fix segfault for buggy BPF script Validate obj->maps ]
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161115040617.69788-5-wangnan0@huawei.com
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit 0b3c2264ae ("perf symbols: Fix kallsyms perf test on ppc64le")
refers struct symbol in probe_event.h, but forgets to include its
definition. Gcc will complain about it when that definition is not
added, by sheer luck, by some other header included before
probe_event.h.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161115040617.69788-4-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Before this patch perf panics if kptr_restrict is set to 1 and perf is
owned by root with suid set:
$ whoami
wangnan
$ ls -l ./perf
-rwsr-xr-x 1 root root 19781908 Sep 21 19:29 /home/wangnan/perf
$ cat /proc/sys/kernel/kptr_restrict
1
$ cat /proc/sys/kernel/perf_event_paranoid
-1
$ ./perf record -a
Segmentation fault (core dumped)
$
The reason is that perf assumes it is allowed to read kptr from
/proc/kallsyms when euid is root, but in fact the kernel doesn't allow
reading kptr when euid and uid do not match with each other:
$ cp /bin/cat .
$ sudo chown root:root ./cat
$ sudo chmod u+s ./cat
$ cat /proc/kallsyms | grep do_fork
0000000000000000 T _do_fork <--- kptr is hidden even euid is root
$ sudo cat /proc/kallsyms | grep do_fork
ffffffff81080230 T _do_fork
See lib/vsprintf.c for kernel side code.
This patch fixes this problem by checking both uid and euid.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161115040617.69788-3-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On ubuntu the internal kernel version code is different from what can
be retrived from uname:
$ uname -r
4.4.0-47-generic
$ cat /lib/modules/`uname -r`/build/include/generated/uapi/linux/version.h
#define LINUX_VERSION_CODE 263192
#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))
$ cat /lib/modules/`uname -r`/build/include/generated/utsrelease.h
#define UTS_RELEASE "4.4.0-47-generic"
#define UTS_UBUNTU_RELEASE_ABI 47
$ cat /proc/version_signature
Ubuntu 4.4.0-47.68-generic 4.4.24
The macro LINUX_VERSION_CODE is set to 4.4.24 (263192 == 0x40418), but
`uname -r` reports 4.4.0.
This mismatch causes LINUX_VERSION_CODE macro passed to BPF script become
an incorrect value, results in magic failure in BPF loading:
$ sudo ./buildperf/perf record -e ./tools/perf/tests/bpf-script-example.c ls
event syntax error: './tools/perf/tests/bpf-script-example.c'
\___ Failed to load program for unknown reason
According to Ubuntu document (https://wiki.ubuntu.com/Kernel/FAQ), the
correct kernel version can be retrived through /proc/version_signature, which
is ubuntu specific.
This patch checks the existance of /proc/version_signature, and returns
version number through parsing this file instead of uname. Version string
is untouched (value returns from uname) because `uname -r` is required
to be consistence with path of kbuild directory in /lib/module.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/20161115040617.69788-2-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For tracepoint events, callchains always contain certain functions.
Sometimes it'd be better to skip those functions as they have no value.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161124011114.7102-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
By using arch->init() to set up some regular expressions to associate
ins_ops to ARM instructions, ditching that old table that has
instructions not present on ARM.
Take advantage of having an arch->init() to hide more arm specific stuff
from the common code, like the objdump details.
The regular expressions comes from a patch written by Kim Phillips.
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-77m7lufz9ajjimkrebtg5ead@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arches like ARM will want to use regular expressions when deciding what
instructions to associate with what ins_ops, provide infrastructure for
that.
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-7dmnk9el2ipu3nxog092k9z5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Some arches may want to dynamically populate the table using regular
expressions on the instruction names to associate them with a set of
parsing/formatting/etc functions (struct ins_ops), so provide a fallback
for when the ins__find() method fails.
That fall back will be able to resize the arch->instructions, setting
arch->nr_instructions appropriately, helper functions to associate an
ins_ops to an instruction name, growing the arch->instructions if needed
and resorting it are provided, all the arch specific callback needs to
do is to decide if the missing instruction should be added to
arch->instructions with a ins_ops association.
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-auu13yradxf7g5dgtpnzt97a@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The disasm_line::name field is always equal to ins::name, being used
just to locate the instruction's ins_ops from the per-arch instructions
table.
Eliminate this duplication, nuking that field and instead make
ins__find() return an ins_ops, store it in disasm_line::ins.ops, and
keep just in disasm_line::ins.name what was in disasm_line::name, this
way we end up not keeping a reference to entries in the per-arch
instructions table.
This in turn will help supporting multiple ways to manage the per-arch
instructions table, allowing resorting that array, for instance, when
the entries will move after references to its addresses were made. The
same problem is avoided when one grows the array with realloc.
So architectures simply keeping a constant array will work as well as
architectures building the table using regular expressions or other
logic that involves resorting the table.
Reviewed-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-vr899azvabnw9gtuepuqfd9t@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
New tool:
- 'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------- ------ ---------------- --------- --------- --------
1.874569 [0011] gcc[31949] 0.014 0.000 1.148
1.874591 [0010] gcc[31951] 0.000 0.000 0.024
1.874603 [0010] migration/10[59] 3.350 0.004 0.011
1.874604 [0011] <idle> 1.148 0.000 0.035
1.874723 [0005] <idle> 0.016 0.000 1.383
1.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec. (David Ahern, Namhyung Kim)
Improvements:
- Make 'perf c2c report' support -f/--force, to allow skipping the
ownership check for root users, for instance, just like the other
tools (Jiri Olsa)
- Allow sorting cachelines by total number of HITMs, in addition to
local and remote numbers (Jiri Olsa)
Fixes:
- Make sure errors aren't suppressed by the TUI reset at the end of
a 'perf c2c report' session (Jiri Olsa)
Infrastructure:
- Initial work on having the annotate code better support multiple
architectures, including the ability to cross-annotate, i.e. to
annotate perf.data files collected on an ARM system on a x86_64
workstation (Arnaldo Carvalho de Melo, Ravi Bangoria, Kim Phillips)
- Use USECS_PER_SEC instead of hard coded number in libtraceevent (Steven Rostedt)
- Add retrieval of preempt count and latency flags in libtraceevent (Steven Rostedt)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gL8a
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-20161123' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New tool:
- 'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------- ------ ---------------- --------- --------- --------
1.874569 [0011] gcc[31949] 0.014 0.000 1.148
1.874591 [0010] gcc[31951] 0.000 0.000 0.024
1.874603 [0010] migration/10[59] 3.350 0.004 0.011
1.874604 [0011] <idle> 1.148 0.000 0.035
1.874723 [0005] <idle> 0.016 0.000 1.383
1.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec. (David Ahern, Namhyung Kim)
Improvements:
- Make 'perf c2c report' support -f/--force, to allow skipping the
ownership check for root users, for instance, just like the other
tools (Jiri Olsa)
- Allow sorting cachelines by total number of HITMs, in addition to
local and remote numbers (Jiri Olsa)
Fixes:
- Make sure errors aren't suppressed by the TUI reset at the end of
a 'perf c2c report' session (Jiri Olsa)
Infrastructure changes:
- Initial work on having the annotate code better support multiple
architectures, including the ability to cross-annotate, i.e. to
annotate perf.data files collected on an ARM system on a x86_64
workstation (Arnaldo Carvalho de Melo, Ravi Bangoria, Kim Phillips)
- Use USECS_PER_SEC instead of hard coded number in libtraceevent (Steven Rostedt)
- Add retrieval of preempt count and latency flags in libtraceevent (Steven Rostedt)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If callchains were recorded they are appended to the line with a default stack depth of 5:
1.874569 [0011] gcc[31949] 0.014 0.000 1.148 wait_for_completion_killable <- do_fork <- sys_vfork <- stub_vfork <- __vfork
1.874591 [0010] gcc[31951] 0.000 0.000 0.024 __cond_resched <- _cond_resched <- wait_for_completion <- stop_one_cpu <- sched_exec
1.874603 [0010] migration/10[59] 3.350 0.004 0.011 smpboot_thread_fn <- kthread <- ret_from_fork
1.874604 [0011] <idle> 1.148 0.000 0.035 cpu_startup_entry <- start_secondary
1.874723 [0005] <idle> 0.016 0.000 1.383 cpu_startup_entry <- start_secondary
1.874746 [0005] gcc[31949] 0.153 0.078 0.022 do_wait sys_wait4 <- system_call_fastpath <- __GI___waitpid
--no-call-graph can be used to not show the callchains. --max-stack is used
to control the number of frames shown (default of 5). -x/--excl options can
be used to collapse redundant callchains to get more relevant data on screen.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-7-namhyung@kernel.org
[ Add documentation based on above commit message ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The -s/--summary option is to show process runtime statistics. And the
-S/--with-summary option is to show the stats with the normal output.
$ perf sched timehist -s
Runtime summary
comm parent sched-in run-time min-run avg-run max-run stddev
(count) (msec) (msec) (msec) (msec) %
---------------------------------------------------------------------------------------------------------
ksoftirqd/0[3] 2 2 0.011 0.004 0.005 0.006 14.87
rcu_preempt[7] 2 11 0.071 0.002 0.006 0.017 20.23
watchdog/0[11] 2 1 0.002 0.002 0.002 0.002 0.00
watchdog/1[12] 2 1 0.004 0.004 0.004 0.004 0.00
...
Terminated tasks:
sleep[7220] 7219 3 0.770 0.087 0.256 0.576 62.28
Idle stats:
CPU 0 idle for 2352.006 msec
CPU 1 idle for 2764.497 msec
CPU 2 idle for 2998.229 msec
CPU 3 idle for 2967.800 msec
Total number of unique tasks: 52
Total number of context switches: 2532
Total run time (msec): 218.036
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-5-namhyung@kernel.org
[ Add documentation from last commit, so that docs comes with the cset that introduces the feature ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------------- ------ -------------------- --------- --------- ---------
79371.874569 [0011] gcc[31949] 0.014 0.000 1.148
79371.874591 [0010] gcc[31951] 0.000 0.000 0.024
79371.874603 [0010] migration/10[59] 3.350 0.004 0.011
79371.874604 [0011] <idle> 1.148 0.000 0.035
79371.874723 [0005] <idle> 0.016 0.000 1.383
79371.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec.
Committer note:
Add above explanation as the 'perf sched timehist' entry for 'man
perf-sched'.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The __symbol__fprintf_symname_offs() always shows symbol offsets. So
there's no difference between 'perf script -F ip,sym' and 'perf script
-F ip,sym,symoff'. I don't think it's a desired behavior..
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding support for cascading options added by Namhyung in:
commit 369a247897 ("tools lib subcmd: Support cascading options")
This way the report and record command share options with with c2c
command and can save some option duplicates. For now it's the 'v'
option.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-7-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently we display the cacheline list sorted on remote HITMs by
default.
The problem is that they might not be always counted and 'perf c2c
report' displays an empty output. Thus it's more convenient to display
and sort the cacheline list based on the total of HITMs and have the
best change to see data in the default report run.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-6-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Count total number of HITMs in a special field. This will ease up
addition of total HITM sorting into c2c report in the following patch.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-5-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding -f/--force option to go through ownership validation:
$ sudo perf c2c report
File perf.data not owned by current user or root (use -f to override)
$
$ sudo perf c2c report -f
< c2c report output >
$
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Because of the early browser switch we won't get possible error
messages, as it will clear the screen right after showing the message,
e.g.:
Before:
$ sudo perf c2c report -d lcl
$
After:
$ sudo perf c2c report -d lcl
File perf.data not owned by current user or root (use -f to override)
$
$ ls -la perf.data
-rw-------. 1 acme acme 26648 Nov 22 15:11 perf.data
$
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is useful for debug to see file descriptors for each event.
Before:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12146 cpu -1 group_fd -1 flags 0x8
...
sys_perf_event_open: pid 12146 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Now:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12858 cpu -1 group_fd -1 flags 0x8 = 3
...
sys_perf_event_open: pid 12858 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a way to retrieve the preempt count as well as the latency flags from a
pevent_record.
int pevent_data_preempt_count(pevent, record);
returns the preempt count of a record.
int pevent_data_flags(pevent, record);
returns the latency flags for a record.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161122113158.03a010a8@gandalf.local.home
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Instead of using 1000000, use the define in time64.h instead.
Also remove the the duplicate defines for NSECS_PER_SEC.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20161121114149.67111981@gandalf.local.home
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull RCU updates from Paul E. McKenney:
- Documentation updates, yet again just simple changes.
- Miscellaneous fixes, including a change to call_rcu()'s
rcu_head alignment check.
- Security-motivated list consistency checks, which are
disabled by default behind DEBUG_LIST.
- Torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a testcase for types of kprobe event. This checks
kprobe event can accept and correctly expressed the
arguments typed as s32, u32, x32 and bitfield.
Here is the test result.
-----
# ./ftracetest test.d/kprobe/kprobe_args_type.tc
=== Ftrace unit tests ===
[1] Kprobes event arguments with types [PASS]
# of passed: 1
# of failed: 0
# of unresolved: 0
# of untested: 0
# of unsupported: 0
# of xfailed: 0
# of undefined(test bug): 0
-----
Link: http://lkml.kernel.org/r/147928409063.22982.3499119203875115458.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add function filter glob matching test case.
This checks whether the kernel supports glob matching
(front match, end match, middle match, side match,
character class and '?').
Here is the test result.
-----
./ftracetest test.d/ftrace/func-filter-glob.tc
=== Ftrace unit tests ===
[1] ftrace - function glob filters [PASS]
# of passed: 1
# of failed: 0
# of unresolved: 0
# of untested: 0
# of unsupported: 0
# of xfailed: 0
# of undefined(test bug): 0
-----
Link: http://lkml.kernel.org/r/147928407589.22982.16364174511117104303.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Introduce TMPDIR variable which is removed after each test
is done, so that the test script can put their temporary
files in that.
Link: http://lkml.kernel.org/r/147928406116.22982.8761924340108532378.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Since histogram trigger id.syscall depends on CONFIG_FTRACE_SYSCALLS,
a testcase in trigger-modifier test fails if that config is disabled.
Fix this bug by using flexible pattern to check the histogram output.
Link: http://lkml.kernel.org/r/147928402670.22982.15589445159052676877.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If "snapshot" special file doesn't exist, that kernel does
not support snapshot and snapshot trigger too. In that case
snapshot trigger test results to unsupported instead of fail.
Link: http://lkml.kernel.org/r/147928401215.22982.10411665829041109794.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reset ftrace to initial state before running each test.
This fixes some test cases to enable tracing before starting
trace test. This can avoid false-positive failure when
previous testcase fails while disabling tracing.
Link: http://lkml.kernel.org/r/147928398192.22982.7767460638302113002.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uleds driver provides userspace LED devices. This tool is used to
create one of these devices and monitor the changes in brighness for
testing purposes.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
- Revert a recent ACPICA cleanup that attempted to get rid of all
FADT version 2 legacy, but broke ACPI thermal management on at
least one system (Rafael Wysocki).
- Fix cross-compiled builds of ACPI tools that stopped working
after a recent cleanup related to the handling of header files
in ACPICA (Lv Zheng).
- Fix a locking issue in the PCC channel initialization code that
invokes devm_request_irq() under a spinlock (among other things)
and causes lockdep to complain (Hoan Tran).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=9ZhJ
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"They fix an ACPI thermal management regression introduced by a recent
FADT handling cleanup, an ACPI tools build issue introduced by a
recent ACPICA commit and a PCC mailbox initialization bug causing
lockdep to complain loudly.
Specifics:
- Revert a recent ACPICA cleanup that attempted to get rid of all
FADT version 2 legacy, but broke ACPI thermal management on at
least one system (Rafael Wysocki).
- Fix cross-compiled builds of ACPI tools that stopped working after
a recent cleanup related to the handling of header files in ACPICA
(Lv Zheng).
- Fix a locking issue in the PCC channel initialization code that
invokes devm_request_irq() under a spinlock (among other things)
and causes lockdep to complain (Hoan Tran)"
* tag 'acpi-4.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power/acpi: Remove direct kernel source include reference
mailbox: PCC: Fix lockdep warning when request PCC channel
Revert "ACPICA: FADT support cleanup"
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
ARM64 hardware expects 64bit aligned address for watchpoint invocation.
However, it provides byte selection method to select any number of
consecutive byte set within the range of 1-8.
This patch adds support to test all such byte selection option for
different memory write sizes.
Patch also adds a test for handling the case when the cpu does not
report an address which exactly matches one of the regions we have
been watching (which is a situation permitted by the spec if an
instruction accesses both watched and unwatched regions). The test
was failing on a MSM8996pro before this patch series and is
passing now.
Signed-off-by: Pavel Labath <labath@google.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We only support breakpoint/watchpoint of length 1, 2, 4 and 8. If we can
support other length as well, then user may watch more data with less
number of watchpoints (provided hardware supports it). For example: if we
have to watch only 4th, 5th and 6th byte from a 64 bit aligned address, we
will have to use two slots to implement it currently. One slot will watch a
half word at offset 4 and other a byte at offset 6. If we can have a
watchpoint of length 3 then we can watch it with single slot as well.
ARM64 hardware does support such functionality, therefore adding these new
definitions in generic layer.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Another step in supporting cross annotation.
The arch specific tables are put in:
tools/perf/arch/$ARCH/annotation/instructions.c
which, so far, just plug instructions to a bunch of parsers/formatters,
but may have more as the need arises.
This is an alternative implementation to a previous attempt made by Ravi
Bangoria.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-g3wt282lfa51j4qd0813e3az@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This is to cope with an ARM specific kludge introduced in the original
patch supporting ARM annotation, cfef25b8da ("perf annotate: ARM
support") that made functions with a '+' in its name to be skipped when
processing call instructions.
With this patchkit it should be possible to collect a perf.data file on
a ARM machine and then annotate it on a x86 workstation and have those
ARM kludges used.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-2fi3sy7q3sssdi7m7cbe07gy@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introduce a 'struct arch', where arch specific stuff will live, starting
with objdump's choice of comment delimitation character, that is '#' in
x86 while a ';' in arm.
This has some bits and pieces from a patch submitted by Ravi.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chris Riyder <chris.ryder@arm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-f337tzjjcl8vtapgvjxmhrbx@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch adds ptrace interface test for TM SPR registers. This
also adds ptrace interface based helper functions related to TM
SPR registers access.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for VSX, VMX registers
inside TM context. This also adds ptrace interface based helper
functions related to chckpointed VSX, VMX registers access.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for VSX, VMX registers.
This also adds ptrace interface based helper functions related
to VSX, VMX registers access. This also adds some assembly
helper functions related to VSX and VMX registers.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for TAR, PPR, DSCR
registers inside TM context. This also adds ptrace
interface based helper functions related to checkpointed
TAR, PPR, DSCR register access.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for TAR, PPR, DSCR
registers. This also adds ptrace interface based helper
functions related to TAR, PPR, DSCR register access.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for GPR/FPR registers
inside suspended TM context.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for GPR/FPR registers
inside TM context. This adds ptrace interface based helper
functions related to checkpointed GPR/FPR access.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds ptrace interface test for GPR/FPR registers.
This adds ptrace interface based helper functions related to
GPR/FPR access and some assembly helper functions related to
GPR/FPR registers.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
[mpe: Add #defines for the new note types when headers don't define them]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are some functions, especially register related, which can
be shared across multiple selftests/powerpc test directories.
This patch creates a new include directory to store those shared
files, so that the file layout becomes more neat.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
[mpe: Reworked to move the headers only]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds SPR number for TAR, PPR, DSCR special
purpose registers. It also adds TM, VSX, VMX related
instructions which will then be used by patches later
in the series.
Now that the new DSCR register definitions (SPRN_DSCR_PRIV and
SPRN_DSCR) are defined outside this directory, use them instead.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Avoid breaking cross-compiled ACPI tools builds by rearranging the
handling of kernel header files.
This patch also contains OUTPUT/srctree cleanups in order to make above fix
working for various build environments.
Fixes: e323c02dee (ACPICA: MSVC9: Fix <sys/stat.h> inclusion order issue)
Reported-and-tested-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch has some unit tests and a test_lru_dist.
The test_lru_dist reads in the numeric keys from a file.
The files used here are generated by a modified fio-genzipf tool
originated from the fio test suit. The sample data file can be
found here: https://github.com/iamkafai/bpf-lru
The zipf.* data files have 100k numeric keys and the key is also
ranged from 1 to 100k.
The test_lru_dist outputs the number of unique keys (nr_unique).
F.e. The following means, 61239 of them is unique out of 100k keys.
nr_misses means it cannot be found in the LRU map, so nr_misses
must be >= nr_unique. test_lru_dist also simulates a perfect LRU
map as a comparison:
[root@arch-fb-vm1 ~]# ~/devshare/fb-kernel/linux/samples/bpf/test_lru_dist \
/root/zipf.100k.a1_01.out 4000 1
...
test_parallel_lru_dist (map_type:9 map_flags:0x0):
task:0 BPF LRU: nr_unique:23093(/100000) nr_misses:31603(/100000)
task:0 Perfect LRU: nr_unique:23093(/100000 nr_misses:34328(/100000)
....
test_parallel_lru_dist (map_type:9 map_flags:0x2):
task:0 BPF LRU: nr_unique:23093(/100000) nr_misses:31710(/100000)
task:0 Perfect LRU: nr_unique:23093(/100000 nr_misses:34328(/100000)
[root@arch-fb-vm1 ~]# ~/devshare/fb-kernel/linux/samples/bpf/test_lru_dist \
/root/zipf.100k.a0_01.out 40000 1
...
test_parallel_lru_dist (map_type:9 map_flags:0x0):
task:0 BPF LRU: nr_unique:61239(/100000) nr_misses:67054(/100000)
task:0 Perfect LRU: nr_unique:61239(/100000 nr_misses:66993(/100000)
...
test_parallel_lru_dist (map_type:9 map_flags:0x2):
task:0 BPF LRU: nr_unique:61239(/100000) nr_misses:67068(/100000)
task:0 Perfect LRU: nr_unique:61239(/100000 nr_misses:66993(/100000)
LRU map has also been added to map_perf_test:
/* Global LRU */
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 16 $i | awk '{r += $3}END{print r " updates"}'; done
1 cpus: 2934082 updates
4 cpus: 7391434 updates
8 cpus: 6500576 updates
/* Percpu LRU */
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 32 $i | awk '{r += $3}END{print r " updates"}'; done
1 cpus: 2896553 updates
4 cpus: 9766395 updates
8 cpus: 17460553 updates
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the --jitter flag specifies jitter for a --build-only
run, the system will obediently build a kernel, refuse to launch it,
launch the requested number of jitter processes, and wait for the
specified kernel run time, which defaults to 30 minutes. This is
of course quite pointless.
This commit therefore disables jitter on build-only runs.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
If the branch is 100% predicted then the "predicted" is hidden.
Similarly, if there is no branch tsx abort, the "abort" is hidden.
There is only cycles shown (cycle is supported on skylake platform,
older platform would be 0).
If no iterations, the "iterations" is hidden.
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/1477876794-30749-6-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If the branch is 100% predicted then the "predicted" is hidden.
Similarly, if there is no branch tsx abort, the "abort" is hidden.
There is only cycles shown (cycle is supported on skylake platform,
older platform would be 0).
If no iterations, the "iterations" is hidden.
For example:
|--29.93%--main div.c:39 (predicted:50.6%, cycles:1, iterations:18)
| main div.c:44 (predicted:50.6%, cycles:1)
| |
| --22.69%--main div.c:42 (cycles:2, iterations:17)
| compute_flag div.c:28 (cycles:2)
| |
| --10.52%--compute_flag div.c:27 (cycles:1)
| rand rand.c:28 (cycles:1)
| rand rand.c:28 (cycles:1)
| __random random.c:298 (cycles:1)
| __random random.c:297 (cycles:1)
| __random random.c:295 (cycles:1)
| __random random.c:295 (cycles:1)
| __random random.c:295 (cycles:1)
| __random random.c:295 (cycles:6)
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/1477876794-30749-5-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull perf fixes from Ingo Molnar:
"An uncore PMU driver hardware enablement change for Intel SkyLake
uncore PMUs (Skylake Y, U, H and S platforms), plus a number of
tooling fixes for the histogram handling/displaying code"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Add more Intel uncore IMC PCI IDs for SkyLake
perf hists: Fix column length on --hierarchy
perf hists browser: Fix column indentation on --hierarchy
perf hists browser: Show folded sign properly on --hierarchy
perf hists browser: Fix indentation of folded sign on --hierarchy
perf hist browser: Fix hierarchy column counts
Create some branch counters in per callchain list entry. Each counter
is for a branch flag. For example, predicted_count counts all the
*predicted* branches. The counters get updated by processing the
callchain cursor nodes.
It also provides functions to retrieve or print the values of counters
in callchain list.
Besides the counting for branch flags, it also counts and returns the
average number of iterations.
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/1477876794-30749-4-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Create a new flag show_branchflag_count in symbol_conf. The flag is used
to control if showing the branch flag counting information. The flag
depends on if the perf.data has branch data and if user chooses the
"branch-history" option in perf report command line.
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/1477876794-30749-3-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since the branch ip has been added to call stack for easier browsing,
this patch adds more branch information. For example, add a flag to
indicate if this ip is a branch, and also add with the branch flag.
Then we can know if the cursor node represents a branch and know what
the branch flag it has.
The branch history code has a loop detection pass that removes loops. It
would be nice for knowing how many loops were removed then in next
steps, we can compute out the average number of iterations.
For example:
Before remove_loops(),
entry0: from = 0x100, to = 0x200
entry1: from = 0x300, to = 0x250
entry2: from = 0x300, to = 0x250
entry3: from = 0x300, to = 0x250
entry4: from = 0x700, to = 0x800
After remove_loops()
entry0: from = 0x100, to = 0x200
entry1: from = 0x300, to = 0x250
entry2: from = 0x700, to = 0x800
The original entry2 and entry3 are removed. So the number of iterations
(from = 0x300, to = 0x250) is equal to removed number + 1 (2 + 1).
iterations = removed number + 1;
average iteractions = Sum(iteractions) / number of samples
This formula ignores other cases, for example, iterations cross multiple
buffers and one buffer contains 2+ loops. Because in practice, it's good
enough.
Signed-off-by: Yao Jin <yao.jin@linux.intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/n/1477876794-30749-2-git-send-email-yao.jin@linux.intel.com
[ Renamed 'iter' to 'nr_loop_iter' for clarity ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To write config items to a particular config file, we should know where
is each config section and item from.
Current setting functionality of perf-config use autogenerating way by
overwriting collected config items to a config file.
For example, when collecting config items from user and system config
files (i.e. ~/.perfconfig and $(sysconf)/perfconfig), perf_config_set
can contain both user and system config items. So we should know where
each value is from to avoid merging user and system config items on user
config file.
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Nambong Ha <over3025@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Wookje Kwon <aweee0@gmail.com>
Link: http://lkml.kernel.org/r/1478241862-31230-7-git-send-email-treeze.taeung@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add setting feature that can add config variables with their values to a
config file (i.e. user or system config file) or modify config key-value
pairs in a config file. For the syntax examples:
perf config [<file-option>] [section.name[=value] ...]
e.g. You can set the ui.show-headers to false with
# perf config ui.show-headers=false
If you want to add or modify several config items, you can do like
# perf config annotate.show_nr_jumps=false kmem.default=slab
Committer notes:
Testing it:
$ perf config -l
top.children=true
report.children=false
$
$ perf config top.children=false
$ perf config -l
top.children=false
report.children=false
$
$ perf config kmem.default=slab
$ perf config -l
top.children=false
report.children=false
kmem.default=slab
$
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Nambong Ha <over3025@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Wookje Kwon <aweee0@gmail.com>
Link: http://lkml.kernel.org/r/1478241862-31230-5-git-send-email-treeze.taeung@gmail.com
[ Combined patch with docs update with this one ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
You can show the values for several config items as below:
# perf config report.queue-size call-graph.record-mode
but it is necessary to more precisely check arguments, before passing
them to show_spec_config(). This validation function would be also used
when parsing config key-value pairs arguments in the near future.
Committer notes:
Testing it:
$ perf config bla.
The config variable does not contain a variable name: bla.
$ perf config .bla
The config variable does not contain a section name: .bla
$ perf config bla.bla
$
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Nambong Ha <over3025@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Wookje Kwon <aweee0@gmail.com>
Link: http://lkml.kernel.org/r/1478241862-31230-4-git-send-email-treeze.taeung@gmail.com
[ Fix some spelling errors ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a functionality getting specific config key-value pairs.
For the syntax examples,
perf config [<file-option>] [section.name ...]
e.g. To query config items 'report.queue-size' and 'report.children', do
# perf config report.queue-size report.children
Signed-off-by: Taeung Song <treeze.taeung@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Nambong Ha <over3025@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Wookje Kwon <aweee0@gmail.com>
Link: http://lkml.kernel.org/r/1478241862-31230-2-git-send-email-treeze.taeung@gmail.com
[ Combined patch with docs update with this one ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now when jvmti compilation is plugged into Makefile.perf, there's no
need for this makefile.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lkml.kernel.org/r/20161112121016.GA17194@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Compile jvmti agent as part of the perf build. The agent library is
called libperf-jvmti.so and is installed in default place together with
other files:
$ make libperf-jvmti.so
BUILD: Doing 'make -j4' parallel build
...
CC jvmti/libjvmti.o
CC jvmti/jvmti_agent.o
LD jvmti/jvmti-in.o
LINK libperf-jvmti.so
$ make DESTDIR=/tmp/krava/ install-bin
...
$ find /tmp/krava/ | grep libperf
/tmp/krava/lib64/libperf-jvmti.so
/tmp/krava/lib64/libperf-gtk.so
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lkml.kernel.org/r/1478093749-5602-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding support to detect jvmti support. It is not plugged into the
FEATURE_TESTS machinery, because it's quite rare and will be used
separately from perf via feature_check call.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lkml.kernel.org/r/1478093749-5602-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding support to remove options from final CFLAGS for both object file
and build target. It's now possible to remove CFLAGS options like:
CFLAGS_REMOVE_krava.o += -Wstrict-prototypes
Committer notes:
This comes from the kernel's kbuild infrastructure, the subset that is
supported in tools/ is being documented at tools/build/Documentation/Build.txt.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lkml.kernel.org/r/1478093749-5602-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Returning a negative value for a boolean function seem to have the
undesired effect of returning true. require_paranoia_below() is a
boolean function, but the variable used to store the return value is an
integer, receiving -1 or 0. This patch converts rc to bool, replaces -1
by false, and 0 by true.
mpe: This wasn't exhibiting in practice because the common case, where
we do the comparison of the desired level vs the current value, was
being compiled into a computation based on the result of the comparison,
ie. it wasn't using the default -1 value at all. However that was just
luck and the code is still wrong.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored won't be supported in POWER9, so PPC_FEATURE2_ARCH_3_00
(in HWCAP2) will no longer imply Load monitor support.
These Load monitored tests are enabled by PPC_FEATURE2_ARCH_3_00 so
they are now bogus and need to be removed.
This reverts commit 16c19a2e98 ("selftests/powerpc: Load Monitor
Register Tests").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This halves the exception table size on 64-bit builds, and it allows
build-time sorting of exception tables to work on relocated kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor asm fixups and bits to keep the selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is taken from s390, and allows more flexibility in
changing exception table format.
mpe: Put it in ppc_asm.h and only define one version using
stringinfy_in_c(). Add some empty definitions and headers to keep the
selftests happy.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the result returned by load_unaligned_zeropad() doesn't match what we
expect we should fail the test!
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the load unaligned zeropad test takes a SEGV which can't be handled,
we increment segv_error, print the offending NIP and then return without
taking any further action. In almost all cases this means we'll just
take the SEGV again, and loop eternally spamming the console.
Instead just abort(), it's a fatal error in the test. The test harness
will notice that the child died and print a nice message for us.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull in a version of Anton's null_syscall benchmark:
http://ozlabs.org/~anton/junkcode/null_syscall.c
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@au.ibm.com>
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- These are fixes for the --hierarchy view of perf top and report, fixing
output oddities, mostly related to scrolling. (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qT5b
-----END PGP SIGNATURE-----
Merge tag 'perf-hists-hierarchy-fixes-for-mingo-20161111' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes for perf {top,report} --hierarchy, from Arnaldo Carvalho de Melo:
- These are fixes for the --hierarchy view of perf top and report, fixing
output oddities, mostly related to scrolling. (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Markus reported that there's a weird behavior on perf top --hierarchy
regarding the column length.
Looking at the code, I found a dubious code which affects the symptoms.
When --hierarchy option is used, the last column length might be
inaccurate since it skips to update the length on leaf entries.
I cannot remember why it did and looks like a leftover from previous
version during the development.
Anyway, updating the column length often is not harmful. So let's move
the code out.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 1a3906a7e6 ("perf hists: Resort hist entries with hierarchy")
Link: http://lkml.kernel.org/r/20161108130833.9263-5-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When horizontall scrolling is used in hierarchy mode, the the right most
column has unnecessary indentation. Actually it's needed only if some
of left (overhead) columns were shown.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161108130833.9263-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When horizontal scrolling is used in hierarchy mode, the folded signed
disappears at the right most column.
Committer note:
To test it, run 'perf top --hierarchy, see the '+' symbol at the first
column, then press the right arrow key, the '+' symbol will disappear,
this patch fixes that.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161108130833.9263-3-namhyung@kernel.org
[ Move 'width -= 2' invariant to right after the if/else ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It should indent 2 spaces for folded sign and a whitespace.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161108130833.9263-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The perf report/top on TUI supports horizontal scrolling using LEFT and
RIGHT keys.
But it calculate the number of columns incorrectly when hierarchy mode
is enabled so that keep pressing RIGHT key can make the output
disappeared.
In the hierarchy mode, all sort keys are collapsed into a single column,
so it needs to be applied when calculating column numbers.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161024162110.17918-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since 841e3558b2 ("perf callchain: Recording 'dwarf' callchains do not
need DWARF unwinding support"), --call-graph dwarf is allowed in 'perf
record' even without unwind support. A couple of other places don't
reflect this yet though: the help text should list dwarf as a valid
record mode and the dump_size config should be respected too.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Cc: He Kuang <hekuang@huawei.com>
Fixes: 841e3558b2 ("perf callchain: Recording 'dwarf' callchains do not need DWARF unwinding support")
Link: http://lkml.kernel.org/r/1470837148-7642-1-git-send-email-rabin.vincent@axis.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch removes checking of socket descriptor value in daemons.
It was checked to be less than FD_SETSIZE(1024 usually) but it's not
correct.
To be exact, the maximum value of descriptor comes from
rlimit(RLIMIT_NOFILE).
Following kernel code determines the value :
get_unused_fd_flags() : fs/files.c
__alloc_fd() : fs/files.c
expand_files() : fs/files.c
The defalut (soft limit) is defines as INR_OPEN_CUR(1024) in
include/linux/fs.h which is referenced form INIT_RLIMS in
include/asm-generic/resource.h. The value may be modified with ulimt,
sysctl, security configuration and etc.
With the kernel code above, when socket() system call returns positive
value, the value must be within rlimit(RLIMIT_NOFILE). No extra
checking is needed when socket() returns positive.
Without 'usbip: vhci number of ports extension' patch set, there's no
practical problem because of number of USB port restriction. With the
patch set, the value of socket descriptor can exceed FD_SETSIZE(1024
usually) if the rlimit is changed.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary header files and netlink related code as the daemons
do not use netlink to communicate with the kernel now.
Signed-off-by: Weibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hv_kvp_daemon.c: In function .kvp_mac_to_if_name.:
hv_kvp_daemon.c:705:2: warning: format not a string literal and no format arguments [-Wformat-security]
snprintf(dev_id, sizeof(dev_id), kvp_net_dir);
^
hv_kvp_daemon.c:705:2: warning: format not a string literal and no format arguments [-Wformat-security]
Signed-off-by: Weibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The link flag pthread is not needed.
Signed-off-by: Weibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the input file fd instead of spidev fd.
The spidev fd is supposed to be OK otherwise the transfer_file() function
would not be called at all.
Signed-off-by: Michal Vokáč <vokac.m@gmail.com>
Reviewed-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When converting to a shared library in ac5a181d06 ("cpupower: Add
cpuidle parts into library"), cpu_freq_cpu_exists() was converted to
cpupower_is_cpu_online(). cpu_req_cpu_exists() returned 0 on success and
-ENOSYS on failure whereas cpupower_is_cpu_online returns 1 on success.
Check for the correct return value in cpufreq-set.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1374212
Fixes: ac5a181d06 (cpupower: Add cpuidle parts into library)
Reported-by: Julian Seward <jseward@acm.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.com>
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Updating the event index has a memory barrier and causes more work
on the other side to actually signal the event. It is unnecessary
if a new buffer has already appeared on the ring, so poll once before
doing the update.
The effect of this on the 0.9 ring implementation is pretty much
invisible, but on the new-style ring it provides a consistent 3%
performance improvement.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide new primitives used_empty/avail_empty and
build poll_avail/poll_used on top of it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By using -flto and -fwhole-program, all functions from the ring implementation
can be treated as static and possibly inlined. Force this to happen through
the GCC flatten attribute.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ac12f6764c ("perf tools: Implement branch_type event parameter") we
started using the parse_branch_str() function from one of the files used
in the python binding, which caused this entry in 'perf test' to fail:
# perf test -v python
16: Try 'import perf' in python, checking link problems :
--- start ---
test child forked, pid 16667
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ImportError: /tmp/build/perf/python/perf.so: undefined symbol:
parse_branch_str
test child finished with -1
---- end ----
Try 'import perf' in python, checking link problems: FAILED!
#
I must've commited some mistake when running 'perf test' to send the
pull request for the perf-core-for-mingo-20161024 tag, to have let this
regression to pass, sigh.
Just add tools/perf/util/parse-branch-options.c and switch from using
ui__warning(), that is not available in the python binding, use
pr_warning() instead, which is good enough for this case.
Now:
# perf test python
16: Try 'import perf' in python, checking link problems : Ok
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Andi Kleen <ak@linux.intel.com>
Fixes: ac12f6764c ("perf tools: Implement branch_type event parameter")
Link: http://lkml.kernel.org/n/tip-9kn1ct1cx9ppwqlmzl6z0xhs@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Removing one more set of die() calls.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-6pyil685m5i2tugg56gcy0tg@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Both register_perl_scripting() and register_python_scripting() allocate
this variable, fix it by checking if it already was.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 7e4b21b84c ("perf/scripts: Add Python scripting engine")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introduced in commit f9afc6197e ("x86: Wire up protection keys system
calls")
This will make 'perf trace' aware of them on x86_64.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-s1ta2ttv2xacecqogmd3a9p1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To get the defines introduced in the commit e8c24d3a23 ("x86/pkeys:
Allocation/free syscalls")
Silencing this perf build warning:
Warning: tools/include/uapi/asm-generic/mman-common.h differs from kernel
Need to change 'perf trace' to beautify those syscalls, as soon as
booting with a kernel with it.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-yev9rexu02cl7cjeozzmrl9t@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ignore export.h and EXPORT_SYMBOL in:
784d5699ed ("x86: move exports to actual definitions")
We're not dragging this stuff, not useful in tools/
This silences the following warnings while building perf:
Warning: tools/arch/x86/lib/memcpy_64.S differs from kernel
Warning: tools/arch/x86/lib/memset_64.S differs from kernel
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-h9vw3pe0fq79zmyqsfr0s0mo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support in perf list topic to only show events belonging to a
specific vendor events topic. For example the following works now:
% perf list frontend
List of pre-defined events (to be used in -e):
stalled-cycles-frontend OR idle-cycles-frontend [Hardware event]
stalled-cycles-frontend OR cpu/stalled-cycles-frontend/ [Kernel PMU event]
frontend:
dsb2mite_switches.count
[Decode Stream Buffer (DSB)-to-MITE switches]
dsb2mite_switches.penalty_cycles
[Decode Stream Buffer (DSB)-to-MITE switch true penalty cycles]
dsb_fill.exceed_dsb_lines
[Cycles when Decode Stream Buffer (DSB) fill encounter more than 3 Decode Stream Buffer (DSB)
lines]
icache.hit
[Number of Instruction Cache, Streaming Buffer and Victim Cache Reads. both cacheable and
noncacheable, including UC fetches]
...
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1476902724-9586-2-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Joonwoo reported that there's a mismatch between timestamps in script
and sched commands. This was because of difference in printing the
timestamp. Factor out the code and share it so that they can be in
sync. Also I found that sched map has similar problem, fix it too.
Committer notes:
Fixed the max_lat_at bug introduced by Namhyung's original patch, as
pointed out by Joonwoo, and made it a function following the scnprintf()
model, i.e. returning the number of bytes formatted, and receiving as
the first parameter the object from where the data to the formatting is
obtained, renaming it from:
char *timestamp_in_usec(char *bf, size_t size, u64 timestamp)
to
int timestamp__scnprintf_usec(u64 timestamp, char *bf, size_t size)
Reported-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20161024020246.14928-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The following commit:
3732710ff6 ("objtool: Improve rare switch jump table pattern detection")
... improved objtool's ability to detect GCC switch statement jump
tables for GCC 6. However the check to allow short jumps with the
scanned range of instructions wasn't quite right. The pattern detection
should allow jumps to the indirect jump instruction itself.
This fixes the following warning:
drivers/infiniband/sw/rxe/rxe_comp.o: warning: objtool: rxe_completer()+0x315: sibling call from callable instruction with changed frame pointer
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 3732710ff6 ("objtool: Improve rare switch jump table pattern detection")
Link: http://lkml.kernel.org/r/20161026153408.2rifnw7bvoc5sex7@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I'd like to see the name of tasks with perf sched map, but it only shows
name of new tasks and then use short names after all. This is not good
for long running tasks since it's hard for users to track the short
names. This patch makes it show the names (except the idle task) when
-v option is used. Probably we may make it as default behavior.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20161024020246.14928-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Applying cpu color always doesn't help readability IMHO. Instead it
might be better to applying the color when there's an activity on those
CPUs.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20161024020246.14928-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The -i and -v options can be used in subcommands so enable cascading the
sched_options. This fixes the following inconvenience in 'perf sched':
$ perf sched -i perf.data.sched map
... (it works well) ...
$ perf sched map -i perf.data.sched
Error: unknown switch `i'
Usage: perf sched map [<options>]
--color-cpus <cpus>
highlight given CPUs in map
--color-pids <pids>
highlight given pids in map
--compact map output in compact mode
--cpus <cpus> display given CPUs in map
With this patch, the second command line works with the perf.data.sched
data file.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20161024030003.28534-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sometimes subcommand have common options and it can only handled in the
upper level command unless it duplicates the options.
This patch adds a parent field and fallback to the parent if the given
argument was not found in the current options.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20161024030003.28534-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The perf report/top on TUI supports horizontal scrolling using LEFT and
RIGHT keys.
But it calculate the number of columns incorrectly when hierarchy mode
is enabled so that keep pressing RIGHT key can make the output
disappeared.
In the hierarchy mode, all sort keys are collapsed into a single column,
so it needs to be applied when calculating column numbers.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161024162110.17918-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sebastian noted that overhead for worker thread ops (throughput)
accounting was producing 'perf' to appear in the profiles, consuming a
non-trivial (i.e. 13%) amount of CPU.
This is due to cacheline bouncing due to the increment of w->ops.
We can easily fix this by just working on a local copy and updating the
actual worker once done running, and ready to show the program summary.
There is no danger of the worker being concurrent, so we can trust that
no stale value is being seen by another thread.
This also gets rid of the unnecessary cache alignment hack; its not
worth it.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/1477342613-9938-2-git-send-email-dave@stgolabs.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add basic gpio operations. User could get/set gpio value for specific
line of gpiochip.
Reference "tools/gpio/gpio-hammer.c" or
"tools/testing/selftest/gpio/gpio-mockup-chardev.c" for how to use it.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the 'perf list' glob matching for vendor events case insensitive.
This allows to use the upper case vendor events with perf list too.
Now the following works:
% perf list LONGEST_LAT
...
cache:
longest_lat_cache.miss
[Core-originated cacheable demand requests missed LLC]
longest_lat_cache.reference
[Core-originated cacheable demand requests that refer to LLC]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1476899402-31460-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Instead of the one when another syscall takes place while another is being
processed (in another CPU, but we show it serialized, so need to "interrupt"
the other), and also when finally showing the sys_enter + sys_exit + duration,
where we were showing the sample->time for the sys_exit, duh.
Before:
# perf trace sleep 1
<SNIP>
0.373 ( 0.001 ms): close(fd: 3 ) = 0
1000.626 (1000.211 ms): nanosleep(rqtp: 0x7ffd6ddddfb0) = 0
1000.653 ( 0.003 ms): close(fd: 1 ) = 0
1000.657 ( 0.002 ms): close(fd: 2 ) = 0
1000.667 ( 0.000 ms): exit_group( )
#
After:
# perf trace sleep 1
<SNIP>
0.336 ( 0.001 ms): close(fd: 3 ) = 0
0.373 (1000.086 ms): nanosleep(rqtp: 0x7ffe303e9550) = 0
1000.481 ( 0.002 ms): close(fd: 1 ) = 0
1000.485 ( 0.001 ms): close(fd: 2 ) = 0
1000.494 ( 0.000 ms): exit_group( )
[root@jouet linux]#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ecbzgmu2ni6glc6zkw8p1zmx@git.kernel.org
Fixes: 752fde44fd ("perf trace: Support interrupted syscalls")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Not used at all, we need just the entry_time to calculate the syscall
duration.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-js6r09zdwlzecvaei7t4l3vd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It popped up in perf testing that the worker consumes some amount of
CPU. It boils down to the increment of `ops` which causes cache line
bouncing between the individual threads.
This patch aligns the struct by 256 bytes to ensure that not a cache
line is shared among CPUs. 128 byte is the x86 worst case and grep says
that L1_CACHE_SHIFT is set to 8 on s390.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161016190803.3392-1-bigeasy@linutronix.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We already have handling for errors when processing PERF_RECORD_ events,
so instead of calling die() when not being able to alloc, propagate the
error, so that the normal UI exit sequence can take place, the user be
warned and possibly the terminal be properly reset to a sane mode.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Brice Goglin <Brice.Goglin@inria.fr>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-r90je3c009a125dvs3525yge@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It already returns whatever strbuf_(grow|addch)() returns in case of
failure, so just return -ENOSPC in the only case where it was die()ing.
When it returns, its only caller will call die() anyway, so no need to
be so eager, die later.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-as05b7mbogprlwi8iarwns8e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Instead of having all tests perform alloc/free, do it in the code that
calls the do_cycles() and do_gettimeofday() functions.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-lywj4mbdb1m9x1z9asivwuuy@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In the perf wiki todo-list[1], there is an entry regarding initial-delay
and 'perf trace'; the following small patch tries to fulfill this point.
It has been generated against the branch tip/perf/core.
It has only been implemented in the "trace__run" case.
Ex.:
$ sudo strace -- ./perf trace --delay 5 sleep 1 2>&1
...
fcntl(7, F_SETFL, O_RDONLY|O_NONBLOCK) = 0
ioctl(7, PERF_EVENT_IOC_ID, 0x7ffc8fd35718) = 0
ioctl(11, PERF_EVENT_IOC_SET_OUTPUT, 0x7) = 0
fcntl(11, F_SETFL, O_RDONLY|O_NONBLOCK) = 0
ioctl(11, PERF_EVENT_IOC_ID, 0x7ffc8fd35718) = 0
write(6, "\0", 1) = 1
close(6) = 0
nanosleep({0, 5000000}, NULL) = 0 # DELAY OF 5 MS BEFORE ENABLING THE EVENTS
ioctl(3, PERF_EVENT_IOC_ENABLE, 0) = 0
ioctl(4, PERF_EVENT_IOC_ENABLE, 0) = 0
ioctl(5, PERF_EVENT_IOC_ENABLE, 0) = 0
ioctl(7, PERF_EVENT_IOC_ENABLE, 0) = 0
...
[1]: https://perf.wiki.kernel.org/index.php/Todo
Signed-off-by: Alexis Berlemont <alexis.berlemont@gmail.com>
Suggested-and-Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161010054328.4028-2-alexis.berlemont@gmail.com
[ Add entry to the manpage, cut'n'pasted from stat's and record's ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Here is a small patch which tries to fulfill a point in the perf todo
list:
* Make pressing 'V' multiple times to go on cycling thru various
verbosity levels in 'perf top', so that info that is present in
'perf top -v' can be obtained without having to restart the tool
(acme).
After a small grep in the code, the max verbosity level seems 3; so,
we cycle at 4; I did not dare define a MAX_VERBOSE_LEVEL constant.
Signed-off-by: Alexis Berlemont <alexis.berlemont@gmail.com>
Suggested-and-Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20161012214823.14324-2-alexis.berlemont@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The latter version occurs much more when running git grep.
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20161013161811.4939-1-alexander@alemayhu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
With uncore event aliases which are duplicated over multiple PMUs the
"Using CPUID" message with -v could be printed many times. Only print
it once.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1476393332-20732-3-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch adds a formal specification of the jitdump format. The goal
is to help jit runtime developers implement the jitdump support without
having to read the jvmti code.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-10-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Check the version number when opening a jitdump file. Accept older
versions, but not newer ones.
Signed-off-by: Stefano Sanfilippo <ssanfilippo@chromium.org>
Signed-off-by: Ross McIlroy <rmcilroy@chromium.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-9-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When the jit_buf_desc contains unwinding information, it is emitted as
eh_frame unwinding sections in the DSOs generated by perf inject.
The unwinding information is required to unwind of JITed code which do
not maintain the frame pointer register during function calls. It can
be emitted by V8 / Chromium when the --perf_prof_unwinding_info is
passed to V8.
The eh_frame and eh_frame_hdr sections are emitted immediately after the
.text.
The .eh_frame is aligned at a 8-byte boundary, and .eh_frame_hdr at a
4-byte one. Since size of the .eh_frame is required to be a multiple of
the word size, which means there will never be additional padding
between it and the .eh_frame_hdr on machines where the word size is 4 or
8 bytes.
However, additional padding might be inserted between .text and
.eh_frame to reach the correct alignment, which will always be 8 bytes,
also on 32bit machines. The reasoning behind this choice is that 4 extra
bytes of padding worst case are not a large cost for the advantage of
removing word-size dependent offset calculations when emitting the
jitdump.
Signed-off-by: Stefano Sanfilippo <ssanfilippo@chromium.org>
Signed-off-by: Ross McIlroy <rmcilroy@chromium.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-8-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This record is intended to provide unwinding information in the
eh_frame format. This is required to unwind JITed code which
does not maintain the frame pointer register during function calls.
The eh_frame unwinding information can be emitted by V8 / Chromium
when the --perf_prof_unwinding_info is passed.
A record of type jr_code_unwinding_info comes before the jr_code_load
it referred to and contains both the .eh_frame and .eh_frame_hdr.
The fields in the header have the following meaning:
* unwinding_size: size of the eh_frame and eh_frame_hdr, necessary
for distinguishing the content from the padding.
* eh_frame_hdr_size: as the name says.
* mapped_size: size of the payload that was in memory at runtime.
typically unwinding_size if the .eh_frame_hdr and .eh_frame were
mapped, or 0 if they weren't. It should always be the former case,
since the .eh_frame is guaranteed to be mapped in memory. However,
certain JITs might want to inject an .eh_frame_hdr with an empty LUT
to trigger fp-based unwinding fallback in libunwind. The only part
of the .eh_frame_hdr that libunwind reads from remote memory is the
LUT, and since there is none, mapping the unwinding info in memory
is not necessary, and 0 in this field signifies that it wasn't.
This practical hack allows to save bytes in code memory for those
JIT compilers that might or might not maintain a valid frame pointer.
The payload that follows is assumed to contain first the .eh_frame and
then the .eh_header_hdr, with no padding between the two.
Signed-off-by: Stefano Sanfilippo <ssanfilippo@chromium.org>
Signed-off-by: Ross McIlroy <rmcilroy@chromium.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-7-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When calculating .eh_frame_hdr base and LUT offsets do not always assume
that pgoff is zero.
The assumption is false for DSOs built from the jitdump by perf inject,
because the ELF header did not exist in memory at sampling time.
Signed-off-by: Stefano Sanfilippo <ssanfilippo@chromium.org>
Signed-off-by: Ross McIlroy <rmcilroy@chromium.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-6-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The behavior before this commit was to skip the remaining portion of the
jitdump in case an unknown record was found, including those records
that perf could handle.
With this change, parsing a record with an unknown id will cause a
warning to be emitted, the record will be skipped and parsing will
resume from the next (valid) one.
The patch aims at making perf more future proof, by extracting as much
information as possible from jitdumps.
Signed-off-by: Stefano Sanfilippo <ssanfilippo@chromium.org>
Signed-off-by: Ross McIlroy <rmcilroy@chromium.org>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-5-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch removes all the string padding generated in the jitdump file.
They are not necessary and were adding unnecessary complexity. Modern
processors can handle unaligned accesses quite well. The perf.data/
jitdump file are always post-processed, no need to add extra complexity
for no real gain.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-4-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch modifies the build dependencies on the jitdump support in
perf. As it stands jitdump was wrongfully made dependent 100% on using
DWARF. However, the dwarf dependency, only exist if generating the
source line table in genelf_debug.c. The rest of the support does not
need DWARF.
This patch removes the dependency on DWARF for the entire jitdump
support. It keeps it only for the genelf_debug.c support.
Signed-off-by: Maciej Debski <maciejd@google.com>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-3-git-send-email-eranian@google.com
Fixes: e12b202f8f ("perf jitdump: Build only on supported archs")
[ Make it build only if NO_LIBELF isn't defined, as jitdump.o will only be built in that case ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch improves the usefulness of error messages generated by the
JVMTI interfac.e This can help identify the root cause of a problem by
printing the actual error code. The patch adds a new helper function
called print_error().
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1476356383-30100-2-git-send-email-eranian@google.com
[ Handle failure to convert numeric error to a string in print_error() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Such as CentOS5, where such define is not present in elf.h.
This file, genelf.c, wasn't being built for several systems, because
it mistakenly was conditional on some DWARF features, now that it
is just needing libelf, after "perf jit: Enable jitdump support without
dwarf" it fails.
So, as preparation for "perf jit: Enable jitdump support without dwarf",
conditionally define it, if not available.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Maciej Debski <maciejd@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-k09qay1cmr0l3fzprmztzy3o@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When the loop body isn't executed at all, then the 'ret' local variable,
that is uninitialized will be used as the return value.
This triggers this error on Alpine Linux:
CC /tmp/build/perf/util/demangle-java.o
CC /tmp/build/perf/util/demangle-rust.o
CC /tmp/build/perf/util/jitdump.o
CC /tmp/build/perf/util/genelf.o
util/jitdump.c: In function 'jit_process':
util/jitdump.c:622:3: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
fprintf(stderr, "injected: %s (%d)\n", path, ret);
^
util/jitdump.c:584:6: note: 'ret' was declared here
int ret;
^
FLEX /tmp/build/perf/util/parse-events-flex.c
/ $ gcc -v
Using built-in specs.
COLLECT_GCC=gcc
COLLECT_LTO_WRAPPER=/usr/libexec/gcc/x86_64-alpine-linux-musl/5.3.0/lto-wrapper
Target: x86_64-alpine-linux-musl
Configured with: /home/buildozer/aports/main/gcc/src/gcc-5.3.0/configure --prefix=/usr --mandir=/usr/share/man --infodir=/usr/share/info
+--build=x86_64-alpine-linux-musl --host=x86_64-alpine-linux-musl --target=x86_64-alpine-linux-musl --with-pkgversion='Alpine 5.3.0' --enable-checking=release
+--disable-fixed-point --disable-libstdcxx-pch --disable-multilib --disable-nls --disable-werror --disable-symvers --enable-__cxa_atexit --enable-esp
+--enable-cloog-backend --enable-languages=c,c++,objc,java,fortran,ada --disable-libssp --disable-libmudflap --disable-libsanitizer --enable-shared
+--enable-threads --enable-tls --with-system-zlib
Thread model: posix
gcc version 5.3.0 (Alpine 5.3.0)
But this so far got under the radar, not causing any build problem, till the
"perf jit: enable jitdump support without dwarf" gets applied, when the above
problem takes place, some combination of inlining or whatever, the problem
is real, so fix it by initializing the variable to zero.
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Maciej Debski <maciejd@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lkml.kernel.org/r/20161013200437.GA12815@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It can be useful to specify branch type state per event, for example if
we want to collect both software trace points and last branch PMU events
in a single collection. Currently this doesn't work because the software
trace point errors out with -b.
There was already a branch-type parameter to configure branch sample
types per event in the parser, but it was stubbed out. This patch
implements the necessary plumbing to actually enable it.
Now:
$ perf record -e sched:sched_switch,cpu/cpu-cycles,branch_type=any/ ...
works.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1476306127-19721-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
- Some editing (params -> parameters)
- Point to the now more complete list of parameters in the perf list
manpage.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1476381433-22959-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Display name of feature instead of just the number
during recording data.
Before:
failed to write feature 13
Now:
failed to write feature HEADER_CPU_TOPOLOGY
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-k9d9trozi5kkx737cy8n5xh5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Display missing features in header info, like:
$ perf report --header-only
# ========
# captured on: Mon Oct 10 09:39:47 2016
...
# missing features: HEADER_TRACING_DATA HEADER_CPU_TOPOLOGY ...
To help in diagnosing problems.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-bh5gp84gobdmyl345dcp64se@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's not displayed in TUI now, putting it into generic part.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-5fk88kejqgi50ye7xdkhiloz@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding for_each_clear_bit macro plus all its the necessary backbone
functions. Taken from related kernel code. It will be used in following
patch.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-cayv2zbqi0nlmg5sjjxs1775@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding version support for libtraceevent.so object.
Using the existing EVENT_PARSE_VERSION variable to construct
the .so object version string, which now consists of:
$(EP_VERSION).$(EP_PATCHLEVEL).$(EP_EXTRAVERSION)
Looks like it was created for this purpose anyway.
The build will now produce following traeceevent libraries:
$ ll libtraceevent*
libtraceevent.a
libtraceevent.so -> libtraceevent.so.1.1.0
libtraceevent.so.1 -> libtraceevent.so.1.1.0
libtraceevent.so.1.1.0
Also the install target will carry them:
$ make DESTDIR=/tmp/krava prefix=/usr install
INSTALL trace_plugins
INSTALL libtraceevent.a
INSTALL libtraceevent.so.1.1.0
$ find /tmp/krava/ | xargs ls -l
...
/tmp/krava/usr/lib64:
total 572
libtraceevent.a
libtraceevent.so -> libtraceevent.so.1.1.0
libtraceevent.so.1 -> libtraceevent.so.1.1.0
libtraceevent.so.1.1.0
...
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-v64z62fh0dwt0ueie5usrnac@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To ease up following patch.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-zpv5gd8y7clwrhh6dq03ucd5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Decompose the do_install function to ease up
the following patch a little.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-zzs19yx8seyors532vuer37w@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding install_headers target to install all headers
under 'include/traceevent' path, like:
$ make DESTDIR=/tmp/krava prefix=/usr install_headers
$ find /tmp/krava/ -type f
/tmp/krava/usr/include/traceevent/kbuffer.h
/tmp/krava/usr/include/traceevent/event-utils.h
/tmp/krava/usr/include/traceevent/event-parse.h
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-if70lj3zhdc3csdqm5webjvc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To get up to the recent compat pread/pwrite changes, that albeit not
being used by 'perf trace' due to some raw_syscalls tracepoint
limitations, trigger this warning when building perf:
Warning: x86_64's syscall_64.tbl differs from kernel
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ilgqhxd9ubkg5f66bx0bht2t@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Change Intel PT and BTS to pass up the length and the instruction
bytes of the decoded or sampled instruction in the perf sample.
The decoder already knows this information, we just need to pass it
up. Since it is only a couple of movs it is not very expensive.
Handle instruction cache too. Make sure ilen is always initialized.
Used in the next patch.
[Adrian: re-base on top (and adjust for) instruction buffer size tidy-up]
[Adrian: add BTS support and adjust commit message accordingly]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/1475847747-30994-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tidy instruction buffer size usage in preparation for copying the
instruction bytes onto samples.
The instruction buffer is presently used for debugging, so rename its
size macro from INTEL_PT_INSN_DBG_BUF_SZ to INTEL_PT_INSN_BUF_SZ, and
use it everywhere.
Note that the maximum instruction size is 15 which is a less efficient size
to copy than 16, which is why a separate buffer size is used.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1475847747-30994-2-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
-----BEGIN PGP SIGNATURE-----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=ZRUt
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
Remove extra parentheses introduced in commit <73e176a tools: iio:
iio_generic_buffer: add -A to force-enable all channels>.
Suggested-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the type of 'force' flag from int to bool and at the same time
rename it to 'force_autochannels' for better readability.
Suggested-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If attribute/s is/are already enabled (by default or via scripts or
manual interaction), issuing -a will fail to enable the channels thereby
one has to manually disable the said attribute/s before proceeding with
auto-enabling.
Add a command-line option -A to force-activate all channels regardless
of their current state.
Suggested-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Normally we limit the main list to contain only entries with HITM %
value > 0.0005, but it might be useful to display all captured entries.
Adding --show-all option for that.
Requested-and-Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-nokgjdwikbegec5jzj4mxhqc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a possibility to disable source line column with new --no-source
option. It source line data could take lot of time to retrieve, so it
could be a performance burden for big data.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-8p6s2727fq8nbsm3it5gix3p@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add man page for c2c command and credits to builtin-c2c.c file.
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-twbp391v8v9f5idp584hlfov@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding help windows to display key/action mappings
for both browsers.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-zni4apopx6a9eyxsosm1ebh1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding TUI support to switch between Node entry versions
in real time with 'n' key.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-xqbw4h4dxig54wff7fd14lao@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The width of symbol and source line entries could get really long
and not convenient to display. Adding support to display only
patrt of such strings and possibility to switch to full length
by uing --full-symbols option or 's' key in TUI browser.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-yxf5hfteyfaoi8xrgczqtyha@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Using resort callbacks to compute the columns' width.
Computing only the global ones, c2c entries have fixed width only.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-zyayvq2u3dzyf3y7i9jza0lw@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Allowing user to configure the way the single cacheline
data are sorted after being sorted by offset.
Adding 'c' option to specify sorting fields for single cacheline:
-c, --coalesce <coalesce fields>
coalesce fields: pid,tid,iaddr,dso
It's allowed to use following combination of fields:
pid - process pid
tid - process tid
iaddr - code address
dso - shared object
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-aka8z31umxoq2gqr5mjd81zr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently we sort and limit displayed data based on the remote HITMs
count. Adding support to switch to local HITMs via --display option:
--display ... lcl,rmt
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-inykbom2f19difvsu1e18avr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a limit for entries number of the cachelines table entries. By
default now it's the 0.0005% minimum of remote HITMs.
Also display only cachelines with remote hitm or store data.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-inykbom2f19difvsu1e18avr@git.kernel.org
[ Disabled for now ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Display global shared cachelines related stats table as part of the
stdio output or when --stats option is speicified:
$ perf c2c report --stats
...
=================================================
Global Shared Cache Line Event Information
=================================================
Total Shared Cache Lines : 1384
Load HITs on shared lines : 5995
Fill Buffer Hits on shared lines : 1726
L1D hits on shared lines : 1943
L2D hits on shared lines : 0
LLC hits on shared lines : 1360
Locked Access on shared lines : 1993
Store HITs on shared lines : 1504
Store L1D hits on shared lines : 1446
Total Merged records : 3527
Original-patch-by: Dick Fowles <rfowles@redhat.com>
Original-patch-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-p0gty8ctbdzisrniwqxhqmhq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Display global stats table as part of the stdio output
or when --stats option is speicified:
$ perf c2c report --stats
=================================================
Trace Event Information
=================================================
Total records : 41237
Locked Load/Store Operations : 4075
Load Operations : 20526
Loads - uncacheable : 0
Loads - IO : 0
Loads - Miss : 552
Loads - no mapping : 31
Load Fill Buffer Hit : 7333
Load L1D hit : 6398
Load L2D hit : 144
Load LLC hit : 4889
Load Local HITM : 1185
Load Remote HITM : 838
Load Remote HIT : 52
Load Local DRAM : 183
Load Remote DRAM : 106
Load MESI State Exclusive : 289
Load MESI State Shared : 0
Load LLC Misses : 1179
LLC Misses to Local DRAM : 15.5%
LLC Misses to Remote DRAM : 9.0%
LLC Misses to Remote cache (HIT) : 4.4%
LLC Misses to Remote cache (HITM) : 71.1%
Store Operations : 20711
Store - uncacheable : 0
Store - no mapping : 1
Store L1D Hit : 20158
Store L1D Miss : 552
No Page Map Rejects : 7
Unable to parse data source : 0
Original-patch-by: Dick Fowles <rfowles@redhat.com>
Original-patch-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-qkyvao3qsrnwazf0w1jvsh7z@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding simple TUI cacheline browser. It triggers when you press 'd' in
the main browser on the specific cacheline.
It allows to navigate through cacheline's offsets and display callchains
(implemented in following patches).
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-fovjwgyusv3rz5qxk3hnahtl@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add the main cachelines TUI browser. It allows to navigate through
cachelines and display their details and callchains (implemented in the
following patches).
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-pk632k4h1uwc5t0lqc7k61zg@git.kernel.org
Link: http://lkml.kernel.org/r/20161021001706.GB23970@krava
[ Handle file with no entries, fixing segfault reported by Kim Phillips ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ACPICA commit bbcb58f7875381d5c7f3d614bad3bc628a3f5cc6
The following build errors can be seen for MacOSX builds:
.../osunixxf.c:882:9: error: 'sem_close' is deprecated [-Werror,-Wdeprecated-declarations]
.../acmacosx.h:122:29: note: expanded from macro 'sem_destroy'
#define sem_destroy sem_close
sem_destroy() issue is caused by the wrong order of the following lines:
#define #sem_destroy sem_close
#include <semaphore.h>
This patch fixes it by removing the buggy re-definitiion. Lv Zheng.
Linux is not affected by this change.
Link: https://github.com/acpica/acpica/commit/bbcb58f7
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 01eb9a58f4cf6300a0feb838a02bc4b1895c76e8
ACPICA commit de5b9c0ef1ccb264cbe57c88f6dd3fbf8229f907
The following build errors can be seen for MacOSX builds:
.../osunixxf.c:829:42: error: 'tmpnam' is deprecated: This function is provided for compatibility reasons only. Due to security concerns inherent in the design of tmpnam(3), it is highly recommended that you use mkstemp(3) instead. [-Werror,-Wdeprecated-declarations]
Using of temporal file name functions can easily result in bus errors on
MacOSX. This patch implements anonymous semaphore using an automatic
increasing number. Lv Zheng.
Linux is not affected by this change.
Link: https://github.com/acpica/acpica/commit/01eb9a58
Link: https://github.com/acpica/acpica/commit/de5b9c0e
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Set resort/display fields for both cachelines and single cacheline
displays.
Cachelines are sorted on:
rmt_hitm
will be made configurable in following patches.
Following fields are display for cachelines:
dcacheline
tot_recs
percent_hitm
tot_hitm,lcl_hitm,rmt_hitm
stores,stores_l1hit,stores_l1miss
dram_lcl,dram_rmt
ld_llcmiss
tot_loads
ld_fbhit,ld_l1hit,ld_l2hit
ld_lclhit,ld_rmthit
The single cacheline is sort by:
offset,rmt_hitm,lcl_hitm
will be made configurable in following patches.
Following fields are display for each cacheline:
percent_rmt_hitm
percent_lcl_hitm
percent_stores_l1hit
percent_stores_l1miss
offset
pid
tid
mean_rmt
mean_lcl
mean_load
cpucnt
symbol
dso
node
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-0rclftliywdq9qr2sjbugb6b@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Allow to setup number of header lines for c2c hists objects.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-4ilsf0ulubrd4y96g7tnpwzk@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
cl_srcline
It displays source line related to the code address that accessed
cacheline. It's a wrapper to global srcline sort entry.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-cmnzgm37mjz56ozsg4mnbgxq@git.kernel.org
[ Remove __maybe_unused from now used 'he' parameter in filter_cb() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
cpucnt
It displays number of distinct cpus that hit cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-ib2kdwam52fby9u2k3ij6lhm@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
median, mean_rmt, mean_lcl, mean_load, stddev
It displays statistics hits related to cacheline accesses.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-m1r4uc9lcykf1jhpvwk2gkj8@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
node
It displays nodes hits related to cacheline accesses.
The node filed comes in 3 flavors:
- node IDs separated by ','
- node IDs with stats for each ID, in following format:
Node{cpus %hitms %stores}
- node IDs with list of affected CPUs in following format:
Node{cpu list}
User can switch the flavor with -N option (-NN,-NNN).
It will be available in TUI to switch this with 'n' key.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-6742e6g0r7n63y5wc4rrgxx5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
They are to be displayed in the single cacheline output:
symbol, dso
They are wrappers for global sort_sym and sort_dso sort entries with c2c
specific headers.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-6742e6g0r7n63y5wc4rrgxx5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
tid
It's a wrapper for global sort_thread sort entry with c2c specific
header.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-fr0socae5skzvz5qbkl85prn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the single cacheline output:
pid
We currently don't have a single 'pid' sort/display entry, which would
output just pid number, hence adding it into c2c code.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3o23qrspxc99b04ci1swlzr6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
They are to be displayed in the main cachelines overall output:
dram_lcl, dram_rmt
They display DRAM rmt/lcl access numbers for specific cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-tl3qqi9ehk6g1fla4z7y0ykd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
They are to be displayed in the single cacheline output:
percent_rmt_hitm, percent_lcl_hitm, percent_stores_l1hit, percent_stores_l1miss
They display percentage of HITMs/stores for specific offset in the
cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-t365aosxtdut8sgrgn8mfoe4@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the main cachelines overall output:
percent_hitm
It displays HITMs percentage for cacheline.
It counts remote HITMs at the moment, but it is changed later to support
local as well, based on the sort configuration.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-czd17qsh5u5z0yc1estz9l2y@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the main cachelines overall output:
tot_loads
It displays sum of all load accesses for cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-czd17qsh5u5z0yc1estz9l2y@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the main cachelines overall output:
tot_recs
It displays sum of all cachelines accesses.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-wojujik7zzen770mxn295mxa@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is to be displayed in the main cachelines overall output:
ld_llcmiss
It displays bare number of LLC misses for cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-wojujik7zzen770mxn295mxa@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add 2 LLC load related dimension key wrappers.
They are to be displayed in the main cachelines overall output:
ld_lclhit, ld_rmthit
They display bare numbers of LLC and remote loads for cacheline.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-ahjg0voaufefboemjuj9yefh@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add 3 loads related dimension key wrappers.
They are to be displayed in the main cachelines overall output:
ld_fbhit, ld_l1hit, ld_l2hit
They all display bare numbers of loads for
FB (Fill Buffer), L1 and L2 cache.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-wxrzhy74zl8fvkvgjae3w1ju@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add 5 stores related dimension key wrappers.
First 3 are to be displayed in the main cachelines overall output:
stores, stores_l1hit, stores_l1miss
The latter 2 are to be displayed within single cacheline output:
cl_stores_l1hit, cl_stores_l1miss
They all display bare numbers of stores for cacheline or its related
offsets.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-qeml8v53v6q3wl5n8vgbf64r@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding 5 hitm related dimension key wrappers.
First 3 are to be displayed in the main cachelines overall output:
tot_hitm, lcl_hitm, rmt_hitm
The latter 2 are to be displayed within single cacheline output:
cl_rmt_hitm, cl_lcl_hitm
They all display bare numbers of remote/local/total HITMs for cacheline
or its related offsets.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-iju5239xa5heqqben65g1u7e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It displays the code address (as hex number) responsible for the
accesses.
Using c2c wrapper to standard 'symbol_iaddr' object to define own header
and simple (just address) code address output.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-rhshygbst6kr75kju0muwt5x@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It displays cacheline offset as hex number.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-m0424ye98lqveg5nopto8qww@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It displays cacheline address as hex number.
Using c2c wrapper to standard 'dcacheline' object to defined own header
and simple (just address) cacheline output.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-21-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding helping macros to define header objects. It will be used in
following patches, that add new dimensions.
The c2c report will support 2 line headers, hence we only define
line[0/1] in macros.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-20-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Decoding and storing c2c_stats for each hist entry. Changing related
function to work with c2c_* objects.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-19-git-send-email-jolsa@kernel.org
[ Add '.nr_entries = 0' to the c2c_stats initialization to fix the build on older distros ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Store cacheline related entries in nested hist object for each cacheline
data. Nested entries are sorted by 'offset' within related cacheline.
We will allow specific sort keys to be configured for nested cacheline
data entries in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-18-git-send-email-jolsa@kernel.org
[ he__get_hists() should return NULL when c2c_hists__init() fails ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding basic sample processing specific hist_entry allocation callbacks
(via hists__add_entry_ops).
Overloading 'struct hist_entry' object with new 'struct c2c_hist_entry'.
The new hist entry object will carry specific stats and nested hists
objects.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-17-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fallback to standard dimensions in case we don't find the dimension
within c2c ones.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-16-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Allow to reuse 'struct sort_entry' objects within c2c dimension support.
In case the 'struct sort_entry' object meets the need of c2c report we
will use it directly in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-15-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding bare bones of dimension support for c2c report.
Main interface functions are:
c2c_hists__init
c2c_hists__reinit
which re/initialize 'struct c2c_hists' object with sort/display entries
string, in a similar way that setup_sorting function does.
We overload the dimension to provide multi line header support for
sort/display entries.
Also we overload base 'struct perf_hpp_fmt' object with 'struct c2c_fmt'
to define c2c specific functions to deal with multi line headers and
spans.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-14-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding c2c report subcommand. It reads the perf.data and displays shared
data analysis.
This patch adds report basic wirings. It gets fully implemented in
following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-13-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding c2c command base wirings. Its implementation is going to be added
gradually in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-11-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introducing c2c_add_stats function helper to cumulate c2c_stats.
Original-patch-by: Dick Fowles <rfowles@redhat.com>
Original-patch-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introducing c2c_decode_stats function, which decodes
data_src data into new struct c2c_stats.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Original-patch-by: Dick Fowles <rfowles@redhat.com>
Original-patch-by: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1474558645-19956-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update nfit_test infrastructure to enable labels for the dimm on the
nfit_test.1 bus. This bus has a pmem region without aliased blk space,
so it is a candidate for dynamically enabling label support by writing
a namespace index block.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
AVX512_4VNNIW - Vector instructions for deep learning enhanced word
variable precision.
AVX512_4FMAPS - Vector instructions for deep learning floating-point
single precision.
These new instructions are to be used in future Intel Xeon & Xeon Phi
processors. The bits 2&3 of CPUID[level:0x07, EDX] inform that new
instructions are supported by a processor.
The spec can be found in the Intel Software Developer Manual (SDM) or in
the Instruction Set Extensions Programming Reference (ISE).
Define new feature flags to enumerate the new instructions in /proc/cpuinfo
accordingly to CPUID bits and add the required xsave extensions which are
required for proper operation.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161018150111.29926-1-piotr.luc@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A BPF program is required to check the return register of a
map_elem_lookup() call before accessing memory. The verifier keeps
track of this by converting the type of the result register from
PTR_TO_MAP_VALUE_OR_NULL to PTR_TO_MAP_VALUE after a conditional
jump ensures safety. This check is currently exclusively performed
for the result register 0.
In the event the compiler reorders instructions, BPF_MOV64_REG
instructions may be moved before the conditional jump which causes
them to keep their type PTR_TO_MAP_VALUE_OR_NULL to which the
verifier objects when the register is accessed:
0: (b7) r1 = 10
1: (7b) *(u64 *)(r10 -8) = r1
2: (bf) r2 = r10
3: (07) r2 += -8
4: (18) r1 = 0x59c00000
6: (85) call 1
7: (bf) r4 = r0
8: (15) if r0 == 0x0 goto pc+1
R0=map_value(ks=8,vs=8) R4=map_value_or_null(ks=8,vs=8) R10=fp
9: (7a) *(u64 *)(r4 +0) = 0
R4 invalid mem access 'map_value_or_null'
This commit extends the verifier to keep track of all identical
PTR_TO_MAP_VALUE_OR_NULL registers after a map_elem_lookup() by
assigning them an ID and then marking them all when the conditional
jump is observed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add JSON files with vendor event naming for Intel and Power8 processors,
allowing users of tools like oprofile to keep using the event names they
are used to, as well as people reading vendor documentation, where such
naming is used (Andi Kleen, Sukadev Bhattiprolu)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IZAQ
-----END PGP SIGNATURE-----
Merge tag 'perf-vendor_events-for-mingo-20161018' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/vendor_events event tables from Arnaldo Carvalho de Melo:
- Add JSON files with vendor event naming for Intel and Power8 processors,
allowing users of tools like oprofile to keep using the event names they
are used to, as well as people reading vendor documentation, where such
naming is used. (Andi Kleen, Sukadev Bhattiprolu)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Ingo Molnar:
"Four tooling fixes, two kprobes KASAN related fixes and an x86 PMU
driver fix/cleanup"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf jit: Fix build issue on Ubuntu
perf jevents: Handle events including .c and .o
perf/x86/intel: Remove an inconsistent NULL check
kprobes: Unpoison stack in jprobe_return() for KASAN
kprobes: Avoid false KASAN reports during stack copy
perf header: Set nr_numa_nodes only when we parsed all the data
perf top: Fix refreshing hierarchy entries on TUI
Add a start of a test suite for kernel selftests. This moves test_verifier
and test_maps over to tools/testing/selftests/bpf/ along with various
code improvements and also adds a script for invoking test_bpf module.
The test suite can simply be run via selftest framework, f.e.:
# cd tools/testing/selftests/bpf/
# make
# make run_tests
Both test_verifier and test_maps were kind of misplaced in samples/bpf/
directory and we were looking into adding them to selftests for a while
now, so it can be picked up by kbuild bot et al and hopefully also get
more exposure and thus new test case additions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
