Hello,
this series first fixes the calculation of the clock rate. The driver will
round up to the nearest clock rate instead of rounding down. Resulting in SPI
devices accessed with a too high SPI clock.
The remaining patches improve the performance of the driver. The changes range
from micro-optimizations like reducing MMIO writes to the controller to
reducing the number of needed interrupts in some use cases.
regards,
Marc
changes since v1:
- added Maxime Ripard's to the existing patches
- 06/10: (was 05/10 in v1)
"spi: spi-sun6i: sun6i_spi_drain_fifo(): introduce sun6i_spi_get_rx_fifo_count() and make use of it"
use FIELD_GET instead of open coding it
(tnx: Maxime Ripard)
- 05/10: "spi: spi-sun6i: sun6i_spi_get_tx_fifo_count: Convert manual shift+mask to FIELD_GET()"
new patch
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
In sun6i_spi_transfer_one() the RX FIFO Ready (SUN6I_INT_CTL_RF_RDY) is
unconditionally enabled.
A RX interrupt is only needed, if more data than fits into the FIFO is going to
be received during this transfer. As the RX-FIFO is drained during transfer
complete interrupt, enable the RX FIFO Ready interrupt only if the data doesn't
fit into the FIFO.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-11-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the Interrupt Control Register is written three
times. This patch collates the three writes into one.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-10-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sun6i_spi_fill_fifo() is called with a length argument of
"sspi->fifo_depth" and "SUN6I_FIFO_DEPTH".
The driver reads the number of free bytes in the FIFO from the hardware and
uses the length argument to limit this value. This is not needed as the number
of free bytes in the FIFO is always less or equal the depth of the FIFO.
This patch removes the length argument and check.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-9-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sun6i_spi_drain_fifo() is called with a length argument of
"sspi->fifo_depth" and "SUN6I_FIFO_DEPTH".
The driver reads the number of available bytes to read from the FIFO from the
hardware and uses the length argument to limit this value. This is not needed
as the FIFO can contain only the fifo depth number of bytes.
This patch removes the length argument and check.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-8-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces the function sun6i_spi_get_rx_fifo_count(), similar to
the existing sun6i_spi_get_tx_fifo_count(), to make the sun6i_spi_drain_fifo()
function a bit easier to read.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-7-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the manual shift+mask in sun6i_spi_get_tx_fifo_count() to
make use of FIELD_GET()
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200706143443.9855-6-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the driver ensures that the length of the transfer
is smaller or equal to SUN6I_MAX_XFER_SIZE. This means the masking of the
length to SUN6I_MAX_XFER_SIZE can be skipped when writing the transfer length
into the registers.
This patch removes the useless masking of the transfer length to
SUN6I_MAX_XFER_SIZE.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-5-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes an useless goto at the end of
sun6i_spi_transfer_one().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A SPI transfer defines the _maximum_ speed of the SPI transfer. However the
driver doesn't take into account that the clock divider is always rounded down
(due to integer arithmetics). This results in a too high clock rate for the SPI
transfer.
E.g.: with a mclk_rate of 24 MHz and a SPI transfer speed of 10 MHz, the
original code calculates a reg of "0", which results in a effective divider of
"2" and a 12 MHz clock for the SPI transfer.
This patch fixes the issue by using DIV_ROUND_UP() instead of a plain
integer division.
While there simplify the divider calculation for the CDR1 case, use
order_base_2() instead of two ilog2() calculations.
Fixes: 3558fe900e ("spi: sunxi: Add Allwinner A31 SPI controller driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello!
Here's a set of 2 patches against Linus' repo. Renesas Reduced Pin Count
Interface (RPC-IF) allows a SPI flash or HyperFlash connected to the SoC
to be accessed via the external address space read mode or the manual mode.
The memory controller driver for RPC-IF registers either SPI or HyperFLash
subdevice, depending on the contents of the device tree subnode; it also
provides the abstract "back end" API that can be used by the "front end"
SPI/MTD drivers to talk to the real hardware...
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
[1/2] dt-bindings: memory: document Renesas RPC-IF bindings
[2/2] memory: add Renesas RPC-IF driver
MBR, Sergei
Hi all,
Although Florian was concerned about a trivial inline check to deal with
shared IRQs adding overhead, the reality is that it would be so small as
to not be worth even thinking about unless the driver was already tuned
to squeeze out every last cycle. And a brief look over the code shows
that that clearly isn't the case.
This is an example of some of the easy low-hanging fruit that jumps out
just from code inspection. Based on disassembly and ARM1176 cycle
timings, patch #2 should save the equivalent of 2-3 shared interrupt
checks off the critical path in all cases, and patch #3 possibly up to
about 100x more. I don't have any means to test these patches, let alone
measure performance, so they're only backed by the principle that less
code - and in particular fewer memory accesses - is almost always
better.
There is almost certainly a *lot* more to be had from careful use of
relaxed I/O accessors, not doing a read-modify-write of CS at every
reset, tweaking the loops further to avoid unnecessary writebacks to
variables, and so on. However since I'm not invested in this personally
I'm not going to pursue it any further; I'm throwing these patches out
as more of a demonstration to back up my original drive-by review
comments, so if anyone want to pick them up and run with them then
please do so.
Robin.
Robin Murphy (3):
spi: bcm3835: Tidy up bcm2835_spi_reset_hw()
spi: bcm2835: Micro-optimise IRQ handler
spi: bcm2835: Micro-optimise FIFO loops
drivers/spi/spi-bcm2835.c | 45 +++++++++++++++++++--------------------
1 file changed, 22 insertions(+), 23 deletions(-)
--
2.23.0.dirty
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
This switches the Lantiq SSC driver over to use GPIO descriptor
handling in the core.
The driver was already utilizing the core to look up and request
GPIOs from the device tree so this is a pretty small change
just switching it over to use descriptors directly instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200625202149.209276-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the IMG SPFI SPI driver to use GPIO descriptors
as obtained from the core instead of GPIO numbers.
The driver was already relying on the core code to look up
the GPIO numbers from the device tree and allocate memory for
storing state etc. By moving to use descriptors handled by
the core we can delete the setup/cleanup functions and
the device state handler that were only dealing with this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Link: https://lore.kernel.org/r/20200625201422.208640-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Nuvoton PSPI driver already uses the core to handle GPIO
chip selects but is using the old GPIO number method and
retrieveing the GPIOs in the probe() call.
Switch it over to using GPIO descriptors saving a bunch of
code and modernizing it.
Compile tested med ARMv7 multiplatform config augmented
with the Nuvoton arch and this driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200625225759.273911-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
On some SPI controllers (like spi-geni-qcom) setting the chip select
is a heavy operation. For instance on spi-geni-qcom, with the current
code, is was measured as taking upwards of 20 us. Even on SPI
controllers that aren't as heavy, setting the chip select is at least
something like a MMIO operation over some peripheral bus which isn't
as fast as a RAM access.
While it would be good to find ways to mitigate problems like this in
the drivers for those SPI controllers, it can also be noted that the
SPI framework could also help out. Specifically, in some situations,
we can see the SPI framework calling the driver's set_cs() with the
same parameter several times in a row. This is specifically observed
when looking at the way the Chrome OS EC SPI driver (cros_ec_spi)
works but other drivers likely trip it to some extent.
Let's solve this by caching the chip select state in the core and only
calling into the controller if there was a change. We check not only
the "enable" state but also the chip select mode (active high or
active low) since controllers may care about both the mode and the
enable flag in their callback.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200629164103.1.Ied8e8ad8bbb2df7f947e3bc5ea1c315e041785a2@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The field mspi->reg_base is annotated as an __iomem pointer. Good.
However, this field is often assigned to a temporary variable:
before being used. For example:
struct fsl_spi_reg *reg_base = mspi->reg_base;
But this variable is missing the __iomem annotation.
So, add the missing __iomem and make sparse & the bot happier.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Link: https://lore.kernel.org/r/20200622162611.83694-1-luc.vanoostenryck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the memory driver for Renesas RPC-IF which registers either SPI or
HyperFLash device depending on the contents of the device tree subnode.
It also provides the absract "back end" device APIs that can be used by
the "front end" SPI/MTD drivers to talk to the real hardware.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/9a3606ec-d4d0-c63a-4fb6-631ab38e621c@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas Reduced Pin Count Interface (RPC-IF) allows a SPI flash or
HyperFlash connected to the SoC to be accessed via the external address
space read mode or the manual mode.
Document the device tree bindings for the Renesas RPC-IF found in the R-Car
gen3 SoCs.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/54a84c75-fa17-9976-d9a6-a69ef67c418b@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The blind and counted loops are always called with nonzero count, so
convert them to do-while loops that lead to slightly more efficient
code generation. With GCC 8.3 this shaves off 1-2 instructions per
iteration in each case.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/9242863077acf9a64e4b3720e479855b88d19e82.1592261248.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ handler only needs the struct spi_controller for the sake of
the completion at the end of a transfer. Passing the struct bcm2835_spi
directly as the IRQ data allows that level of indirection to be pushed
into the completion path for the reverse lookup, and avoided entirely
in all other cases.
This saves one explicit load in the critical path, plus (for a GCC 8.3
build) two registers worth of stack frame overhead.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/6b401cb521539caffab21f05b4c8cba6c9d27c6e.1592261248.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMAP2 MCSPI has some kind of half-baked GPIO CS support:
it includes code like this:
if (gpio_is_valid(spi->cs_gpio)) {
ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
(...)
But it doesn't parse the "cs-gpios" attribute in the device
tree to count the number of GPIOs or pick out the GPIO numbers
and put these in the SPI master's .cs_gpios property.
We complete the implementation of supporting CS GPIOs
from the device tree and switch it over to use the SPI core
for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200625231257.280615-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the chip select on the Qualcomm geni SPI controller isn't
exactly cheap. Let's cache the current setting and avoid setting the
chip select if it's already right.
Using "flashrom" to read or write the EC firmware on a Chromebook
shows roughly a 25% reduction in interrupts and a 15% speedup.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626151946.1.I06134fd669bf91fd387dc6ecfe21d44c202bd412@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the MODULE_DEVICE_TABLE macro for the platform_device_id table to
allow proper creation of modalias strings and fix autoloading module for
this driver.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/1592962286-25752-3-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is expected to support device ID "spi_altera" for MMIO accessed
devices, device ID "subdev_spi_altera" for indirect accessed devices. But
the platform bus will not try driver name match anymore if the platform
driver has an id_table. So the "spi_altera" should also be added to
id_table.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/1592962286-25752-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback pio feature in case dma transfer failed before start.
Besides, another whole pio transfer including setup_transfer will be
issued by spi core, no need to restore jobs like commit bcd8e7761e ("spi:
imx: fallback to PIO if dma setup failure").
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-3-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback to pio mode in case dma transfer failed with error status
SPI_TRANS_FAIL_NO_START.
If spi client driver want to enable this feature please set xfer->error in
the proper place such as dmaengine_prep_slave_sg() failure detect(but no
any data put into spi bus yet). Besides, add master->fallback checking in
its can_dma() so that spi core could switch to pio next time. Please refer
to spi-imx.c.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-2-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To follow onto Doug's latest spi geni series[1] this simplifies and
reduces the code a little more.
[1] https://lore.kernel.org/r/20200618150626.237027-1-dianders@chromium.org
Stephen Boyd (2):
spi: spi-geni-qcom: Simplify setup_fifo_xfer()
spi: spi-geni-qcom: Don't set {tx,rx}_rem_bytes unnecessarily
drivers/spi/spi-geni-qcom.c | 55 +++++++++++++++++--------------------
1 file changed, 25 insertions(+), 30 deletions(-)
base-commit: 7ba9bdcb91
--
Sent by a computer, using git, on the internet
We only need to test for these counters being non-zero when we see the
end of a transfer. If we're doing a CS change then they will already be
zero. This implies that we don't need to set these to 0 if we're
cancelling an in flight transfer too, because we only care to test these
counters when the 'DONE' bit is set in the hardware and we've set them
to non-zero for a transfer.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of SPI_FULL_DUPLEX (3) is really SPI_TX_ONLY (1) ORed
with SPI_RX_ONLY (2). Let's drop the define and simplify the code here a
bit by collapsing the setting of 'm_cmd' into conditions that are the
same.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handler calls completion and is IRQ requested before the
completion is initialized. Logically it should be the other way.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During shutdown, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
shutdown reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: dc23482599 ("spi: spi-fsl-dspi: Adding shutdown hook")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: 05209f4570 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of SPI_FULL_DUPLEX (3) is really SPI_TX_ONLY (1) ORed
with SPI_RX_ONLY (2). Let's drop the define and simplify the code here a
bit by collapsing the setting of 'm_cmd' into conditions that are the
same.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200618233959.160032-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<vadivel.muruganx.ramuthevar@linux.intel.com> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Resend v3:
Rebased onto v5.7-c1
v3:
Split handling of probe deferral into separate patch (out of 5/6)
Split dropping of redundant WREN to separate patch (out of 5/6)
Fix a possible memleak due to lack of spi_master_put()
Parse all SPI slave nodes in cqspi_setup_flash()
Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next
v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.
Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/
Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path
drivers/mtd/spi-nor/controllers/Kconfig | 11 -
drivers/mtd/spi-nor/controllers/Makefile | 1 -
drivers/spi/Kconfig | 11 +
drivers/spi/Makefile | 1 +
.../spi-cadence-quadspi.c} | 541 +++++++-----------
5 files changed, 222 insertions(+), 343 deletions(-)
rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
base-commit: b3a9e3b962
--
2.26.2
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move cadence-quadspi driver to use spi-mem framework. This is required
to make the driver support for SPI NAND flashes in future.
Driver is feature compliant with existing SPI NOR version.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-8-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care
of sending WREN command before sending erase command.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-7-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider
is not yet probed. Currently driver just falls back to using PIO mode
(which is less efficient) in this case. Instead return probe deferral
error as is so that driver will be re probed once DMA provider is
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-6-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to undo the prior changes done by the driver when exiting due
to failure to acquire reset lines.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-5-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver fails to acquire DMA channel then don't initialize
rx_dma_complete struct as it won't be used.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-4-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently direct access mode is used on platforms that have AHB window
(memory mapped window) larger than flash size. This feature is limited
to TI platforms as non TI platforms have < 1MB of AHB window.
Therefore introduce a driver quirk to disable DAC mode and set it for
non TI compatibles. This is in preparation to move to spi-mem framework
where flash geometry cannot be known.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop configuration of Flash size, erase size and page size
configuration. Flash size is needed only if using AHB decoder (BIT 23 of
CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN
automatically. But since SPI NOR layer takes care of sending WREN, there
is no need to configure these fields either.
Therefore drop these in preparation to move the driver to spi-mem
framework where flash geometry is not visible to controller driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Updated the regmap & indirect access support for spi-altera.
Patch #1 is an 1:1 replacement of of readl/writel with regmap_read/write
Patch #2 introduced a new platform_device_id to support indirect access as
a sub device.
Patch #3 is a minor fix.
Main changes from v1:
- Split the regmap supporting patch to 2 patches.
- Add a new platform_device_id to support indirect access.
- Removed the v1 patch "move driver name string to header file". Now we
use driver name string directly.
- Add Yilun's Signed-off-by for Patch #3.
- Add Tom's Reviewed-by.
Matthew Gerlach (1):
spi: altera: fix size mismatch on 64 bit processors
Xu Yilun (2):
spi: altera: use regmap-mmio instead of direct mmio register access
spi: altera: support indirect access to the registers
drivers/spi/Kconfig | 1 +
drivers/spi/spi-altera.c | 127 +++++++++++++++++++++++++++++++++++++++--------
2 files changed, 107 insertions(+), 21 deletions(-)
--
2.7.4
