New ASUS B650/B660/X670 boards firmware have not exposed WMI monitoring
GUID and entrypoint method WMBD could be implemented for different device
UID.
Implement the direct call to entrypoint method for monitoring the device
UID of B550/X570 boards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Co-developed-by: Ahmad Khalifa <ahmad@khalifa.ws>
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230111212241.7456-1-pauk.denis@gmail.com
[groeck: Fix multi-line formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GXP SoC can support up to 16 fans through the interface provided by
the CPLD. The current support is limited to 8 fans. The fans speeds are
controlled via 8 different PWMs which can vary in value from 0-255. The
fans are also capable of reporting if they have failed to the CPLD which
in turn reports the status to the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20230103203654.59322-2-nick.hawkins@hpe.com
[groeck: Improved alignment of defined, added missing include linux/bits.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for Ampere SMpro hwmon driver. This driver
supports accessing various CPU sensors provided by the SMpro co-processor
including temperature, power, voltages, and current.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a specific MFD_SY7636A config option.
As part of this change we can use MFD_SY7636A as a dependency for all
SY7636a components and also remove the name from MFD_SIMPLE_MFD_I2C as
it no longer needs to be selectable.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220525115554.430971-2-alistair@alistair23.me
MAX31760 is a precision fan speed controller with nonvolatile lookup table.
Device has one internal and one external temperature sensor support.
Controls two fans and measures their speeds. Generates hardware alerts when
programmable max and critical temperatures are exceeded.
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Reviewed-by: Nurettin Bolucu <Nurettin.Bolucu@analog.com>
Link: https://lore.kernel.org/r/20220910171945.48088-2-Ibrahim.Tilki@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The SENSORS_ASPEED is part of the Aspeed silicon so it makes
sense to depend on ARCH_ASPEED and for compile testing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20220916120936.372591-1-pbrobinson@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.
The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.
Additionally, serial number and firmware version are exposed through
debugfs.
Registry offsets were discovered and tested by users on Github [1] [2].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220907100739.806571-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for Microchip EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.
Modify Makefile and Kconfig to support Microchip EMC2305 RPM-based
PWM Fan Speed Controller.
Signed-off-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220810171552.56417-3-michaelsh@nvidia.com
[groeck: Drop unnecessary () around DIV_ROUND_CLOSEST()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Quadro fan controller, which communicates
through a proprietary USB HID protocol. Implemented by Jack Doan [1].
Four temperature sensors and PWM controllable fans are available. The
liquid flow sensor is also exposed, implemented by Leonard Anderweit [2].
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9
Originally-from: Jack Doan <me@jackdoan.com>
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile just fine on ARCH=arm. Allow to select
these drivers if COMPILE_TEST is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20220527153445.1871086-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The polynomial calculation function was moved into lib/ to be able to
reuse it. Move over to this one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-3-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This splits the nct6775 driver into an interface-independent core and
a separate platform driver that wraps inb/outb port I/O (or asuswmi
methods) around that core.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220427010154.29749-7-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware
temperature sensors of the Aquacomputer Farbwerk RGB controller, which
communicates through a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
Also, add Jack Doan to MAINTAINERS for this driver.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Until now, only the temperature sensors where exported thru
the thermal subsystem. Export the fans as "dell-smm-fan[1-3]" too
to make them available as cooling devices.
Also update Documentation and fix a minor issue with the alphabetic
ordering of the includes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220410163935.7840-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Octo fan controller, which communicates
through a proprietary USB HID protocol.
Four temperature sensors and eight PWM controllable fans are available.
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220404134212.9690-1-savicaleksa83@gmail.com
[groeck: Add missing "select CRC16"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a927 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
- Add support for Maxim MAX77714 PMIC
- Remove Drivers
- Remove support for ST-Ericsson AB8500 DebugFS
- New Device Support
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
- New Functionality
- Add support for Reboot to Rockchip RK808
- Fix-ups
- Device Tree changes (inc. YAML conversion); silergy,sy7636a, maxim,max77843,
google,cros-ec, maxim,max14577, maxim,max77802,
maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576
-----BEGIN PGP SIGNATURE-----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=1xnI
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TMP125 is a 2 degree Celsius accurate Digital
Temperature Sensor with a SPI interface.
The temperature register is a 16-bit, read-only register.
The MSB (Bit 15) is a leading zero and never set. Bits 14
to 5 are the 1+9 temperature data bits in a two's
complement format. Bits 4 to 0 are useless copies of
Bit 5 value and therefore ignored.
This was tested on a Aerohive HiveAP-350.
Bonus: lm70 supports TMP122/TMP124 as well.
I added them to the Kconfig module description.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/43b19cbd4e7f51e9509e561b02b5d8d0e7079fac.1645175187.git.chunkeey@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is not the laptops, but the /proc/i8k interface that is legacy (or so
I think was the intention of the help text author). The old description
was confusing, fix this.
The phrase "Say Y if you intend to run this kernel on old Dell laptops
or want to use userspace package i8kutils." was introduced in 2015, in
commit 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
I think that "old laptops" was about hotkey and Fn key support - this
driver in the 2.4 kernels' era apparently had these capabilities
(see: https://github.com/vitorafsr/i8kutils , description of
"repeat_rate" kernel module parameter).
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Pali Rohár <pali@kernel.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Gross <markgross@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220212125654.357408-2-mat.jonczyk@o2.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In Kconfig, inside the "Processor type and features" menu, there is
the CONFIG_I8K option: "Dell i8k legacy laptop support". This is
very confusing - enabling CONFIG_I8K is not required for the kernel to
support old Dell laptops. This option is specific to the dell-smm-hwmon
driver, which mostly exports some hardware monitoring information and
allows the user to change fan speed.
This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig,
where it belongs.
Also, modify the dependency order - change
select SENSORS_DELL_SMM
to
depends on SENSORS_DELL_SMM
as it is just a configuration option of dell-smm-hwmon. This includes
changing the option type from tristate to bool. It was tristate because
it could select CONFIG_SENSORS_DELL_SMM=m .
When running "make oldconfig" on configurations with
CONFIG_SENSORS_DELL_SMM enabled , this change will result in an
additional question (which could be printed several times during
bisecting). I think that tidying up the configuration is worth it,
though.
Next patch tweaks the description of CONFIG_I8K.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Pali Rohár <pali@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Gross <markgross@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using regmap lets us use the regmap subsystem for SPI vs. I2C register
accesses. It lets us hide access differences in backend code and lets
the common code just access registers without knowing their size.
We can also use regmap for register caching.
Tested-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides the same data as the asus_wmi_ec_sensors driver
(and gets it from the same source) but does not use WMI, polling
the ACPI EC directly.
That provides two enhancements: sensor reading became quicker (on some
systems or kernel configuration it took almost a full second to read
all the sensors, that transfers less than 15 bytes of data), the driver
became more flexible. The driver now relies on ACPI mutex to lock access
to the EC in the same way as the WMI code does.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220124015658.687309-2-eugene.shalygin@gmail.com
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using local caching in this driver had few benefits. It used cached values
for two seconds and then re-read all registers from the chip even if the
user only accessed a single attribute. On top of that, alarm attributes
were stale for up to four seconds (the first status register read reports
and clears an alarm, the second reports it cleared). Use regmap instead
for caching. Do not re-read non-volatile registers, and do not cache
volatile registers.
As part of this change, handle register read and write address differences
in regmap code. This is necessary to avoid problems with caching in the
regmap core, and ultimately simplifies the code.
Also, errors observed when reading from and writing to registers are no
longer ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add peci-cputemp driver for Digital Thermal Sensor (DTS) thermal
readings of the processor package and processor cores that are
accessible via the PECI interface.
The main use case for the driver (and PECI interface) is out-of-band
management, where we're able to obtain the DTS readings from an external
entity connected with PECI, e.g. BMC on server platforms.
Co-developed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-11-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver implements monitoring and control of fans plugged into the
device. Besides typical speed monitoring and PWM duty cycle control,
voltage and current are reported for every fan.
The device also has 2 connectors for RGB LEDs, support for them isn't
implemented (mainly because there is no standardized sysfs interface).
Also, the device has a noise sensor, but the sensor seems to be completely
useless (and very imprecise), so support for it isn't implemented too.
The driver coexists with userspace tools that access the device through
hidraw interface with no known issues.
The driver has been tested on x86_64, built in and as a module.
Some changes/improvements were suggested by Jonas Malaco.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver has been augmented to just use device properties
so the OF dependency can be dropped.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211215142933.1409324-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only possible assignment of a function to get a voltage to
convert to a resistance is to use the internal function
ntc_adc_iio_read() which is only available when using IIO
and OF.
Bite the bullet and mandate OF and IIO, drop the read_uv()
callback abstraction and some ifdefs.
As no board is using the platform data, all users are using
OF and IIO anyway.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211125020841.3616359-4-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
