The max number of allowed logical addresses was set to 1 in
vivid, for no good reason. This prevented testing with multiple
logical addresses for the same CEC device. Increase this number to
CEC_MAX_LOG_ADDRS.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
Signed-off-by: Krzysztof Halasa <khalasa@piap.pl>
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
deleted the repeated word 'the' in the comments.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SAMA5D2 does not have the YCYC field for the RLP (rounding, limiting,
packaging) module.
The YCYC field is supposed to work with interleaved YUV formats like YUYV.
In SAMA5D2, we have to use YYCC field, which is used for both planar
formats like YUV420 and interleaved formats like YUYV.
Fix the according rlp callback to replace the generic YCYC field (which
makes more sense from a logical point of view) with the required YYCC
field.
Fixes: debfa49687 ("media: atmel: atmel-isc-base: add support for more formats and additional pipeline modules")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/pci/ivtv/ivtv-i2c.c:245 ivtv_i2c_register() error: buffer overflow 'hw_devicenames' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:266 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:269 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:275 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:280 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
drivers/media/pci/ivtv/ivtv-i2c.c:290 ivtv_i2c_register() error: buffer overflow 'hw_addrs' 21 <= 31
The logic at ivtv_i2c_register() could let buffer overflows at
hw_devicenames and hw_addrs arrays.
This won't happen in practice due to a carefully-contructed
logic, but it is not error-prune.
Change the logic in a way that will make clearer that the
I2C hardware flags will affect the size of those two
arrays, and add an explicit check to avoid buffer overflows.
While here, use the bit macro.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
So, use a kmalloc'ed buffer.
Cc: stable@vger.kernel.org # Kernel 4.9 and upper
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The logic at delta_ipc_open() tries to copy past the size of
the name passed to it:
drivers/media/platform/sti/delta/delta-ipc.c:178 delta_ipc_open() error: __memcpy() 'name' too small (17 vs 32)
Basically,this function is called just one with:
ret = delta_ipc_open(pctx, "JPEG_DECODER_HW0", ...);
The string used there has just 17 bytes. Yet, the logic tries
to copy the entire name size (32 bytes), which is plain wrong.
Replace it by strscpy, which is good enough to copy the string,
warranting that this will be NUL-terminated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the "default m", as options should default to disabled.
No other media driver is enabled by default.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Geniatech MyGica T230C2_LITE and T230A as many people
are asking support for these devices on forums.
Link: https://lore.kernel.org/linux-media/YMuptIYFLdwSmw//@kali
Signed-off-by: Ján Čáni <pego149@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener
to another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance
(for pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require
jump labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast address
allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks
in NAPI context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and NXP
(our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm 60GHz WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LvtX
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
Merge misc updates from Andrew Morton:
"191 patches.
Subsystems affected by this patch series: kthread, ia64, scripts,
ntfs, squashfs, ocfs2, kernel/watchdog, and mm (gup, pagealloc, slab,
slub, kmemleak, dax, debug, pagecache, gup, swap, memcg, pagemap,
mprotect, bootmem, dma, tracing, vmalloc, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (191 commits)
mm,hwpoison: make get_hwpoison_page() call get_any_page()
mm,hwpoison: send SIGBUS with error virutal address
mm/page_alloc: split pcp->high across all online CPUs for cpuless nodes
mm/page_alloc: allow high-order pages to be stored on the per-cpu lists
mm: replace CONFIG_FLAT_NODE_MEM_MAP with CONFIG_FLATMEM
mm: replace CONFIG_NEED_MULTIPLE_NODES with CONFIG_NUMA
docs: remove description of DISCONTIGMEM
arch, mm: remove stale mentions of DISCONIGMEM
mm: remove CONFIG_DISCONTIGMEM
m68k: remove support for DISCONTIGMEM
arc: remove support for DISCONTIGMEM
arc: update comment about HIGHMEM implementation
alpha: remove DISCONTIGMEM and NUMA
mm/page_alloc: move free_the_page
mm/page_alloc: fix counting of managed_pages
mm/page_alloc: improve memmap_pages dbg msg
mm: drop SECTION_SHIFT in code comments
mm/page_alloc: introduce vm.percpu_pagelist_high_fraction
mm/page_alloc: limit the number of pages on PCP lists when reclaim is active
mm/page_alloc: scale the number of pages that are batch freed
...
vma_lookup() finds the vma of a specific address with a cleaner interface
and is more readable.
Link: https://lkml.kernel.org/r/20210521174745.2219620-15-Liam.Howlett@Oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hi Linus,
Please, pull the following patch that fixes an out-of-bounds
warning in the media subsystem. This is part of the ongoing
efforts to globally enable -Warray-bounds.
Thanks!
-----BEGIN PGP SIGNATURE-----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=PfCd
-----END PGP SIGNATURE-----
Merge tag 'array-bounds-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull array-bounds fixes from Gustavo Silva:
"Fix an out-of-bounds warning in the media subsystem.
This is part of the ongoing efforts to globally enable -Warray-bounds"
* tag 'array-bounds-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
media: siano: Fix out-of-bounds warnings in smscore_load_firmware_family2()
v4l2_ctrl_new_std() fails if the caller provides no 'step' parameter for
integer control, so define it to fix following error:
s5p_mfc_dec_ctrls_setup:1166: Adding control (1) failed
Fixes: c3042bff91 ("media: s5p-mfc: Use display delay and display enable std controls")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the vpu is not running, we should not rely on VPU_IDLE_REG
value. In this case, the suspend cb should only unprepare the
clock. This fixes a system-wide suspend to ram failure:
[ 273.073363] PM: suspend entry (deep)
[ 273.410502] mtk-msdc 11230000.mmc: phase: [map:ffffffff] [maxlen:32] [final:10]
[ 273.455926] Filesystems sync: 0.378 seconds
[ 273.589707] Freezing user space processes ... (elapsed 0.003 seconds) done.
[ 273.600104] OOM killer disabled.
[ 273.603409] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 273.613361] mwifiex_sdio mmc2:0001:1: None of the WOWLAN triggers enabled
[ 274.784952] mtk_vpu 10020000.vpu: vpu idle timeout
[ 274.789764] PM: dpm_run_callback(): platform_pm_suspend+0x0/0x70 returns -5
[ 274.796740] mtk_vpu 10020000.vpu: PM: failed to suspend: error -5
[ 274.802842] PM: Some devices failed to suspend, or early wake event detected
[ 275.426489] OOM killer enabled.
[ 275.429718] Restarting tasks ...
[ 275.435765] done.
[ 275.447510] PM: suspend exit
Fixes: 1f565e263c ("media: mtk-vpu: VPU should be in idle state before system is suspended")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i.MX6 device tree include files contain dangling endpoints for the
board device tree writers' convenience. These are still included in
many existing device trees.
Treat dangling endpoints as non-existent to support them.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 612b385efb ("media: video-mux: Create media links in bound notifier")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The syscall bpf(BPF_PROG_QUERY, &attr) should use the prog_cnt field to
see how many entries user space provided and return ENOSPC if there are
more programs than that. Before this patch, this is not checked and
ENOSPC is never returned.
Note that one lirc device is limited to 64 bpf programs, and user space
I'm aware of -- ir-keytable -- always gives enough space for 64 entries
already. However, we should not copy program ids than are requested.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210623213754.632-1-sean@mess.org
Smatch static checker warns that "mdev" can be null:
sound/usb/media.c:287 snd_media_device_create()
warn: 'mdev' can also be NULL
If CONFIG_MEDIA_CONTROLLER is disabled, this file should not be included
in the build.
The below conditions in the sound/usb/Makefile are in place to ensure that
media.c isn't included in the build.
sound/usb/Makefile:
snd-usb-audio-$(CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER) += media.o
select SND_USB_AUDIO_USE_MEDIA_CONTROLLER if MEDIA_CONTROLLER &&
(MEDIA_SUPPORT=y || MEDIA_SUPPORT=SND_USB_AUDIO)
The following config check in include/media/media-dev-allocator.h is
in place to enable the API only when CONFIG_MEDIA_CONTROLLER and
CONFIG_USB are enabled.
#if defined(CONFIG_MEDIA_CONTROLLER) && defined(CONFIG_USB)
This check doesn't work as intended when CONFIG_USB=m. When CONFIG_USB=m,
CONFIG_USB_MODULE is defined and CONFIG_USB is not. The above config check
doesn't catch that CONFIG_USB is defined as a module and disables the API.
This results in sound/usb enabling Media Controller specific ALSA driver
code, while Media disables the Media Controller API.
Fix the problem requires two changes:
1. Change the check to use IS_ENABLED to detect when CONFIG_USB is enabled
as a module or static. Since CONFIG_MEDIA_CONTROLLER is a bool, leave
the check unchanged to be consistent with drivers/media/Makefile.
2. Change the drivers/media/mc/Makefile to include mc-dev-allocator.o
in mc-objs when CONFIG_USB is enabled.
Link: https://lore.kernel.org/alsa-devel/YLeAvT+R22FQ%2FEyw@mwanda/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10635 image sensor embedded in the camera module is currently
reset after the MAX9271 initialization with two long delays that were
most probably not correctly characterized.
Re-work the image sensor reset procedure by holding the chip in reset
during the MAX9271 configuration, removing the long sleep delays and
only wait after the chip exits from reset for 350-500 microseconds
interval, which is larger than the minimum (2048 * (1 / XVCLK)) timeout
characterized in the chip manual.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The camera module initialization routine does not check the return
value of a few functions. Fix that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the device is identified the driver currently reports the
names of the chips embedded in the camera module.
Report the name of the camera module itself instead.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the noise immunity threshold at the end of the rdacm20
initialization routine.
The rdacm20 camera module has been so far tested with a startup
delay that allowed the embedded MCU to program the serializer. If
the initialization routine is run before the MCU programs the
serializer and the image sensor and their addresses gets changed
by the rdacm20 driver it is required to manually enable the noise
immunity threshold to make the communication on the control channel
more reliable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no reason to allocate dynamically the 'serializer' field in
the driver structure.
Embed the field and adjust all its users in the driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current RDACM21 initialization routine powers up the OV10640 image
sensor after the OV490 ISP. The ISP is programmed with a firmware loaded
from an embedded serial flash that (most probably) tries to interact and
program also the image sensor connected to the ISP.
As described in commit "media: i2c: rdacm21: Fix OV10640 powerup" the
image sensor powerdown signal is kept high by an internal pull up
resistor and occasionally fails to startup correctly if the powerdown
line is not asserted explicitly. Failures in the OV10640 startup causes
the OV490 firmware to fail to boot correctly resulting in the camera
module initialization to fail consequentially.
Fix this by powering up the OV10640 image sensor before testing the
OV490 firmware boot completion, by splitting the ov10640_initialize()
function in an ov10640_power_up() one and an ov10640_check_id() one.
Also make sure the OV10640 identification procedure gives enough time to
the image sensor to resume after the programming phase performed by the
OV490 firmware by repeating the ID read procedure.
This commit fixes a sporadic start-up error triggered by a failure to
detect the OV490 firmware boot completion:
rdacm21 8-0054: Timeout waiting for firmware boot
[hverkuil: fixed two typos in commit log]
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV10640 image sensor powerdown signal is controlled by the first
line of the OV490 GPIO pad #1, but the pad #0 identifier
OV490_GPIO_OUTPUT_VALUE0 was erroneously used. As a result the image
sensor powerdown signal was never asserted but was left floating and
kept high by an internal pull-up resistor, causing sporadic failures
during the image sensor startup phase.
Fix this by using the correct GPIO pad identifier and wait the mandatory
1.5 millisecond delay after the powerup lane is asserted. The reset
delay is not characterized in the chip manual if not as "255 XVCLK +
initialization". Wait for at least 3 milliseconds to guarantee the SCCB
bus is available.
While at it also fix the reset sequence, as the reset line was released
before the powerdown one, and the line was not cycled.
This commit fixes a sporadic start-up error triggered by a failure to
read the OV10640 chip ID:
rdacm21 8-0054: OV10640 ID mismatch: (0x01)
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a delay after the OV490 chip is put in reset state. The reset
signal shall be held low for at least 250 useconds.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9271 chip manual prescribes a delay of 5 milliseconds
after the chip exits from low power state.
Add a new function to the max9271 library driver that wakes up the chip
with a dummy i2c transaction and implements the correct delay of 5
milliseconds after the chip exits from low power state.
Use the newly introduced function in the rdacm20 and rdacm21 camera
drivers. The former was not respecting the required delay while the
latter was waiting for a too-short timeout.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of the max9271_write() function in the
max9271 library driver.
While at it, modify an existing condition to be made identical
to other checks.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rephrase a comment in .bound() callback to make it clear we register
a subdev notifier and remove a redundant comment about disabling i2c
auto-ack.
No functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide a macro to define the reverse channel amplitude to
be used to compensate the remote serializer noise immunity.
While at it, update a comment.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cache the current channel amplitude in a driver variable
to skip updating it if the newly requested value is the same
as the currently configured one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the reverse_channel_mv variable to init_rev_chan_mv as
the next patch will cache the reverse channel amplitude in
a new driver variable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following kerneldoc warnings:
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_INIT' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_SET_PARAM' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_ENCODE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'AP_IPIMSG_ENC_DEINIT' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_INIT_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_SET_PARAM_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_ENCODE_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Enum value 'VPU_IPIMSG_ENC_DEINIT_DONE' not described in enum 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Excess enum value 'VPU_IPIMSG_ENC_XXX_DONE' description in 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:31: warning: Excess enum value 'AP_IPIMSG_ENC_XXX' description in 'venc_ipi_msg_id'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:120: warning: Enum value 'VENC_IPI_MSG_STATUS_OK' not described in enum 'venc_ipi_msg_status'
drivers/media/platform/mtk-vcodec/venc_ipi_msg.h:120: warning: Enum value 'VENC_IPI_MSG_STATUS_FAIL' not described in enum 'venc_ipi_msg_status'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_MISC' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_LD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_TOP' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_CM' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_AD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_AV' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_PP' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWD' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWQ' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWB' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VDEC_HWG' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'NUM_MAX_VDEC_REG_BASE' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VENC_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'VENC_LT_SYS' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:50: warning: Enum value 'NUM_MAX_VCODEC_REG_BASE' not described in enum 'mtk_hw_reg_idx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:58: warning: Enum value 'MTK_INST_DECODER' not described in enum 'mtk_instance_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:58: warning: Enum value 'MTK_INST_ENCODER' not described in enum 'mtk_instance_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_NONE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_BITRATE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_FRAMERATE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_INTRA_PERIOD' not described in enum
'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_FORCE_INTRA' not described in enum
'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:87: warning: Enum value 'MTK_ENCODE_PARAM_GOP_SIZE' not described in enum 'mtk_encode_param'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'fourcc' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'type' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'num_planes' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:103: warning: Function parameter or member 'flags' not described in 'mtk_video_fmt'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:112: warning: Function parameter or member 'fourcc' not described in 'mtk_codec_framesizes'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:112: warning: Function parameter or member 'stepwise' not described in 'mtk_codec_framesizes'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:120: warning: Enum value 'MTK_Q_DATA_SRC' not described in enum 'mtk_q_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:120: warning: Enum value 'MTK_Q_DATA_DST' not described in enum 'mtk_q_type'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'visible_width' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'visible_height' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'coded_width' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'coded_height' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'field' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'bytesperline' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'sizeimage' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:134: warning: Function parameter or member 'fmt' not described in 'mtk_q_data'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:177: warning: Function parameter or member 'clk_name' not described in 'mtk_vcodec_clk_info'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:177: warning: Function parameter or member 'vcodec_clk' not described in
'mtk_vcodec_clk_info'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:185: warning: Function parameter or member 'clk_info' not described in 'mtk_vcodec_clk'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:185: warning: Function parameter or member 'clk_num' not described in 'mtk_vcodec_clk'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'vdec_clk' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'larbvdec' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'venc_clk' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'larbvenc' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'dev' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:198: warning: Function parameter or member 'mtkdev' not described in 'mtk_vcodec_pm'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:300: warning: Function parameter or member 'decoded_frame_cnt' not described in
'mtk_vcodec_ctx'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:332: warning: Function parameter or member 'min_bitrate' not described in
'mtk_vcodec_enc_pdata'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:405: warning: Function parameter or member 'venc_pdata' not described in 'mtk_vcodec_dev'
drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h:405: warning: Function parameter or member 'decode_workqueue' not described in
'mtk_vcodec_dev'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_INIT' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_START' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_END' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_DEINIT' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'AP_IPIMSG_DEC_RESET' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_INIT_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_START_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_END_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_DEINIT_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Enum value 'VPU_IPIMSG_DEC_RESET_ACK' not described in enum 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Excess enum value 'AP_IPIMSG_XXX' description in 'vdec_ipi_msgid'
drivers/media/platform/mtk-vcodec/vdec_ipi_msg.h:27: warning: Excess enum value 'VPU_IPIMSG_XXX_ACK' description in 'vdec_ipi_msgid'
In some cases I just changed /** to /*, in other cases the missing
field descriptions were added.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to use & to get the start address of an array.
Fix the size of vga_edid.edid to a single block (128 bytes) to fix
this smatch error:
adv7842.c:2538 adv7842_set_edid() error: memcpy() '&state->vga_edid.edid' too small (128 vs 512)
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It is only read-from, so make it const. In order to be able to do this,
constify all places where mxc_jpeg_fmt is used, in function arguments,
return values and pointers. On top of that, make the name a pointer to
const char.
On aarch64, this shrinks object code size with 550 bytes with gcc 11.1.0,
and almost 2kB with clang 12.0.0.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of mxc_jpeg_m2m_ops is to pass its address to
v4l2_m2m_init() which takes a pointer to const struct v4l2_m2m_ops. Make
it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for two new media bus formats, Y10 and Y8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Prefer 'unsigned int' to bare use of 'unsigned'.
So modified variable type 'unsigned' to 'unsigned int' in v4l2-event.c.
Signed-off-by: lijian <lijian@yulong.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixed all the Coding style issues generated by checkpatch.pl.
The changes made considering the --strict option.
Signed-off-by: Piyush Thange <pthange19@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The m2m_ctx resources was allocated by v4l2_m2m_ctx_init() in g2d_open()
should be freed from g2d_release() when it's not used.
Fix it
Fixes: 918847341a ("[media] v4l: add G2D driver for s5p device family")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When i2c_new_client_device() fails, cafe_pci_probe() cleans up all
resources and returns 0. The patch sets the error code on the
corresponding path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
