Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment, these values are wiped out anyway by the rps
enable/disable. That will be changed in the next patch though.
v2: Add post install setup to address issue found by Damien in the next
patch.
replaced
WARN_ON(dev_priv->rps.pm_iir != 0);
with rps.pm_iir = 0;
With the v2 of this patch and the deferred pm enabling (which changed
since the original patches) we're now able to get PM interrupts before
we've brought up enabled rps. At this point in boot, we don't want to do
anything about it, so we simply ignore it. Since writing the original
assertion, the code has changed quite a bit, and I believe removing this
assertion is perfectly safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: I don't agree with the justification to drop the WARN and
added a FIXME to that effect.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW has some special requirements for the VEBOX. Splitting out the
interrupt handler will make the code a bit nicer and less error prone
when we begin to handle those.
The slight functional change in this patch (queueing work while holding
the spinlock) is intentional as it makes a subsequent patch a bit nicer.
The change should also only effect HSW platforms.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was accidentally broken in the south error interrupt handling
work:
commit 8664281b64
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Apr 12 17:57:57 2013 -0300
drm/i915: report Gen5+ CPU and PCH FIFO underruns
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Well, as well as we can without completely revamping the drm vblank
code. The issue are that
- The vblank code needs to work on both ums and kms.
- It deals always deals with pipes.
- It doesn't take any of the kms locks.
The last part is not really fixable without revamping the drm vblank
code, since the drm core <-> driver interactions is a veritable pile
of spaghettis. But the other pieces can be fixed by switching on the
MODESET driver flag and either checking the hw state directly (ums
case) or just querying our sw tracking (with broken locking, but
that's not worse than what we've had).
Note that this essentially reverts
commit 702e7a56af
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Oct 23 18:29:59 2012 -0200
drm/i915: convert PIPECONF to use transcoder instead of pipe
for the ums case, which will fix a NULL deref (since we really don't
have any crtcs set up).
But the real reason to do this is to drop our reliance on the
cpu_transcoder: By only checking intel_crtc->active we don't need to
make sure that the pipe_config (or at least the cpu_transcoder)
contain safe values even when the pipe is off.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation to track per ring progress in hangcheck,
add i915_hangcheck_ring_hung.
v2: omit dev parameter (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of relying in acthd, track ring seqno progression
to detect if ring has hung.
v2: put hangcheck stuff inside struct (Chris Wilson)
v3: initialize hangcheck.seqno (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for next commit, pass seqno as a parameter
to i915_hangcheck_ring_idle as it will be used inside
i915_hangcheck_elapsed.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 142e239849
Author: Egbert Eich <eich@suse.de>
Date: Thu Apr 11 15:57:57 2013 +0200
drm/i915: Add bit field to record which pins have received HPD events (v3)
added a bit field for hotplug event tracking. There ended up being three
different v3 of the patch: [1], [2], and [3]. Apparently [1] was the
correct one, but some frankenstein combination of the three got
committed, which reversed the logic for setting the hotplug bits and
misplaced a continue statement, skipping the hotplug irq storm handling
altogether.
This lead to broken hotplug detection, bisected to
commit 321a1b3026
Author: Egbert Eich <eich@suse.de>
Date: Thu Apr 11 16:00:26 2013 +0200
drm/i915: Only reprobe display on encoder which has received an HPD event (v2)
which uses the incorrectly set hotplug event bits.
Fix the mess.
[1] http://mid.gmane.org/1366112220-7638-6-git-send-email-eich@suse.de
[2] http://mid.gmane.org/1365688677-13682-1-git-send-email-eich@suse.de
[3] http://mid.gmane.org/1365688996-13874-1-git-send-email-eich@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes "unclaimed register" messages when the power well is
disabled and there's a GPU hang.
v2: Use the new intel_display_power_enabled().
v3: Use the new domains for intel_display_power_enabled().
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both intel_opregion_enable_asle() and intel_enable_asle() have shrunk
considerably. Merge them together into a static function in i915_irq.c,
and rename to better reflect the purpose and the related platforms.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Realize that intel_enable_asle() is never called on PCH-split platforms
or on VLV. Rip out the GSE irq enable for PCH-split platforms, which
also happens to be incorrect for IVB+.
This should not cause any functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the previous work asle and gse interrupt handlers should now be
functionally the same. Drop the duplicated code.
v2: Drop intel_opregion_gse_intr() also in the !CONFIG_ACPI path. (Damien)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, the Punit doesn't automatically drop the GPU to it's minimum
voltage level when entering RC6, so we arm a timer to do it for us from
the RPS interrupt handler. It'll generally only fire when we go idle
(or if for some reason there's a long delay between RPS interrupts), but
won't be re-armed again until the next RPS event, so shouldn't affect
power consumption after we go idle and it triggers.
v2: use delayed work instead of timer + work queue combo (Ville)
v3: fix up delayed work cancel (must be outside lock) (Daniel)
fix up delayed work handling func for delayed work (Jesse)
v4: cancel delayed work before RPS shutdown (Jani)
pass delay not absolute time to mod_delayed_work (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of calling into the DRM helper layer to poll all connectors for
changes in connected displays probe only those connectors which have
received a hotplug event.
v2: Resolved conflicts with changes in previous commits.
Renamed function and and added a WARN_ON() to warn of
intel_hpd_irq_event() from being called without
mode_config.mutex held - suggested by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it is possible to limit 're'-detect() of displays to connectors
which have received an HPD event.
v2: Reordered drm_i915_private: Move hpd_event_bits to hpd state tracking.
v3: Fixed merge conflicts with previous patches.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is bad news and shouldn't be happening.
V2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable hoptplug detection when we encounter a hotplug event
storm. Still hotplug detection is required on some outputs (like
Display Port). The interrupt storm may be only temporary (on certain
Dell Laptops for instance it happens at certain charging states of
the system). Thus we enable it after a certain grace period (2 minutes).
Should the interrupt storm persist it will be detected immediately
and it will be disabled again.
v2: Reordered drm_i915_private: moved hotplug_reenable_timer to hpd state tracker.
v3: Clarified loop start value,
Removed superfluous test for Ivybridge and Haswell,
Restructured loop to avoid deep nesting (all suggested by Ville Syrjälä)
v4: Fixed two bugs pointed out by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch disables hotplug interrupts if an 'interrupt storm'
has been detected.
Noise on the interrupt line renders the hotplug interrupt useless:
each hotplug event causes the devices to be rescanned which will
will only increase the system load.
Thus disable the hotplug interrupts and fall back to periodic
device polling.
v2: Fixed cleanup typo.
v3: Fixed format issues, clarified a variable name,
changed pr_warn() to DRM_INFO() as suggested by
Jani Nikula <jani.nikula@linux.intel.com>.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To disable previously enabled HPD IRQs we need to reset them and
set the enabled ones individually.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a hotplug IRQ storm detection (triggered when a hotplug interrupt
fires more than 5 times / sec).
Rationale:
Despite of the many attempts to fix the problem with noisy hotplug
interrupt lines we are still seeing systems which have issues:
Once cause of noise seems to be bad routing of the hotplug line
on the board: cross talk from other signals seems to cause erronous
hotplug interrupts. This has been documented as an erratum for the
the i945GM chipset and thus hotplug support was disabled for this
chipset model but others seem to have this problem, too.
We have seen this issue on a G35 motherboard for example:
Even different motherboards of the same model seem to behave
differently: while some only see only around 10-100 interrupts/s
others seem to see 5k or more.
We've also observed a dependency on the selected video mode.
Also on certain laptops interrupt noise seems to occur duing
battery charging when the battery is at a certain charge levels.
Thus we add a simple algorithm here that detects an 'interrupt storm'
condition.
v2: Fixed comment.
v3: Reordered drm_i915_private: moved hpd state tracking to hotplug work stuff.
v4: Followed by Jesse Barnes to use a time_..() macro.
v5: Fixed coding style as suggested by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Increase the number of fence registers to 32 on IVB/HSW. VLV however
only has 16 fence registers according to the docs.
Increasing the number of fences was attempted before [1], but there was
some uncertainty about the maximum CPU fence number for FBC. Since then
BSpec has been updated to state that there are in fact 32 fence registers,
and the CPU fence number field in the SNB_DPFC_CTL_SA register is 5 bits,
and the CPU fence number field in the ILK_DPFC_CONTROL register must be
zero. So now it all makes sense.
[1] http://lists.freedesktop.org/archives/intel-gfx/2011-October/012865.html
v2: Include some background information based on the previous attempt
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Interrupts, clock gating, LVDS, and GMBUS are all within the, "this will
be bad for CPU" range when we have PCH_NOP.
There is a bit of a hack in init clock gating. We want to do most of the
clock gating, but the part we skip will hang the system. It could
probably be abstracted a bit better, but I don't feel it's too
unsightly.
v2: Use inverse HAS_PCH_NOP check (Jani)
v3: Actually do what I claimed in v2 (spotted by Daniel)
Merge Ivybridge IRQ handler PCH check to decrease whitespace (Daniel)
Move LVDS bail into this patch (Ben)
v4: logical rebase conflict resolution with SDEIIR (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Brush up patch a bit and resolve conflicts:
- Adjust PCH_NOP checks due to Egbert's hpd handling rework.
- Addd a PCH_NOP check in the irq uninstall code.
- Resolve conflicts with Paulo's SDE irq handling race fix.
v5: Drop the added hunks in the ilk irq handler again, they're bogus.
OOps.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- It's a static function
- I just added a few more users to it
- Its sister ironlake_enable_display_irq is not marked as inline
- The compiler will still inline if it thinks it should do
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now with Egbert Eich's hpd infrastructure rework merged this is dead
simple. And we need this to make output detection work on SDVO - with
the cleaned-up drm polling helpers outputs which claim to have hpd
support are no longer polled.
Now SDVO claims to do that, but it's not actually wired up. So just do
it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Noticed while reviewing the hotplug irq setup code. Just looks better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After
"Convert HPD interrupts to make use of HPD pin assignment in encoders."
This function is now basically the same as i915_hpd_irq_setup().
Consolidating both functions in one requires one more check for
I915_HAS_HOTPLUG(dev) in the i965 code path and one more check for
IS_G4X(dev) in the i915 code path. These are considered harmless.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup patch conflict and make it compile.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a regression introduced in
commit e5868a318d
Author: Egbert Eich <eich@suse.de>
Date: Thu Feb 28 04:17:12 2013 -0500
DRM/i915: Convert HPD interrupts to make use of HPD pin assignment in encode
Due to the irq setup rework in 3.9, see
commit 20afbda209
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 11 14:05:07 2012 +0100
drm/i915: Fixup hpd irq register setup ordering
Egbert Eich's hpd rework blows up on pch-split platforms - it walks
the encoder list before that has been set up completely. The new init
sequence is:
1. irq enabling
2. modeset init
3. hpd setup
We need to move around the ibx setup a bit to fix this.
Ville Syrjälä pointed out in his review that we can't touch SDEIER
after the interrupt handler is set up, since that'll race with Paulo
Zanoni's PCH interrupt race fix:
commit 44498aea29
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Feb 22 17:05:28 2013 -0300
drm/i915: also disable south interrupts when handling them
We fix that by unconditionally enabling all interrupts in SDEIER, but
masking them as-needed in SDEIMR. Since only the single-threaded
setup/teardown (or suspend/resume) code touches that, no further
locking is required.
While at it also simplify the mask handling - we start out with all
interrupts cleared in the postinstall hook, and never enable a hpd
interrupt before hpd_irq_setup is called.
And finally, for consistency rename the ibx hpd setup function to
ibx_hpd_irq_setup.
v2: Fix race around SDEIER writes (Ville).
v3: Remove the superflous posting read for SDEIER, spotted by Ville.
Ville also wondered whether we shouldn't clear SDEIIR, since now
SDE interrupts are enabled before we have an irq handler installed.
But the master interrupt control bit in DEIER is still cleared, so we
should be fine.
Cc: Egbert Eich <eich@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=62798
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to enable HPD interrupts for individual pins to only receive
hotplug events from lines which are connected and working.
v2: Restructured initailization of const arrays following a suggstion
by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't read it when capturing the error state. This solves
"unclaimed register" messages on Haswell when we have a GPU hang.
V2: Check for HAS_PCH_SPLIT instead of Gen5+ because VLV still has
this register.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once we thought we got semaphores working, we disabled kicking the ring
if hangcheck fired whilst waiting upon a ring as it was doing more harm
than good:
commit 4e0e90dcb8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Dec 14 13:56:58 2011 +0100
drm/i915: kicking rings stuck on semaphores considered harmful
However, life is never that easy and semaphores are still causing
problems whereby the value written by one ring (bcs) is not being
propagated to the waiter (rcs). Thus the waiter never wakes up and we
declare the GPU hung, which often has unfortunate consequences, even if
we successfully reset the GPU.
But the GPU is idle as it has completed the work, just didn't notify its
clients. So we can detect the incomplete wait during hang check and
probe the target ring to see if has indeed emitted the breadcrumb seqno
following the work and then and only then kick the waiter.
Based on a suggestion by Ben Widawsky.
v2: cross-check wait with iphdr. fix signaller calculation.
References: https://bugs.freedesktop.org/show_bug.cgi?id=54226
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid this:
[ 256.798060] [drm] capturing error event; look for more information
in/sys/kernel/debug/dri/0/i915_error_state
Ben Widawsky identified that this regression has been introduced in
commit 2f86f19165
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jan 28 15:32:15 2013 -0800
drm/i915: Error state should print /sys/kernel/debug
...
[danvet: split up long line.] <----- he did it
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Pimp commit message with the regression note. Also, order
more brown paper bags, I've run out.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From the docs:
"IIR can queue up to two interrupt events. When the IIR is cleared,
it will set itself again after one clock if a second event was
stored."
"Only the rising edge of the PCH Display interrupt will cause the
North Display IIR (DEIIR) PCH Display Interrupt even bit to be set,
so all PCH Display Interrupts, including back to back interrupts,
must be cleared before a new PCH Display interrupt can cause DEIIR
to be set".
The current code works fine because we don't get many interrupts, but
if we enable the PCH FIFO underrun interrupts we'll start getting so
many interrupts that at some point new PCH interrupts won't cause
DEIIR to be set.
The initial implementation I tried was to turn the code that checks
SDEIIR into a loop, but we can still get interrupts even after the
loop is done (and before the irq handler finishes), so we have to
either disable the interrupts or mask them. In the end I concluded
that just disabling the PCH interrupts is enough, you don't even need
the loop, so this is what this patch implements. I've tested it and it
passes the 2 "PCH FIFO underrun interrupt storms" I can reproduce:
the "ironlake_crtc_disable" case and the "wrong watermarks" case.
In other words, here's how to reproduce the problem fixed by this
patch:
1 - Enable PCH FIFO underrun interrupts (SERR_INT on SNB+)
2 - Boot the machine
3 - While booting we'll get tons of PCH FIFO underrun interrupts
4 - Plug a new monitor
5 - Run xrandr, notice it won't detect the new monitor
6 - Read SDEIIR and notice it's not 0 while DEIIR is 0
Q: Can't we just clear DEIIR before SDEIIR?
A: It doesn't work. SDEIIR has to be completely cleared (including the
interrupts stored on its back queue) before it can flip DEIIR's bit to
1 again, and even while you're clearing it you'll be getting more and
more interrupts.
Q: Why does it work by just disabling+enabling the south interrupts?
A: Because when we re-enable them, if there's something on the SDEIIR
register (maybe an interrupt stored on the queue), the re-enabling
will make DEIIR's bit flip to 1, and since we'll already have
interrupts enabled we'll get another interrupt, then run our irq
handler again to process the "back" interrupts.
v2: Even bigger commit message, added code comments.
Note that this fixes missed dp aux irqs which have been reported for
3.9-rc1. This regression has been introduced by switching to
irq-driven dp aux transactions with
commit 9ee32fea5f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Dec 1 13:53:48 2012 +0100
drm/i915: irq-drive the dp aux communication
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18588.html
References: https://lkml.org/lkml/2013/2/26/769
Tested-by: Imre Deak <imre.deak@intel.com>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp commit message with references for the dp aux irq
timeout regression this fixes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On error, this represents the state of the currently running context at
the time it was loaded.
Unfortunately, since we're hung and can't switch out the context this
may not tell us too much about the most current state of the context,
but does give clues about what has happened since loading.
Thanks to recent doc updates, we have a little more confidence regarding
what is actually in this memory, and perhaps it will help us gain more
insight into certain bugs. AFAICT, the most interesting info is in the
first page. To save space, we only capture the first page. In the
future, we might want to dump more.
Sample of the relevant part of error state:
render ring --- HW Context = 0x01b20000
[0000] 00000000 1100105f 00002028 ffff0880
[0010] 0000209c feff4040 000020c0 efdf0080
[0020] 00002178 00000001 0000217c 00145855
[0030] 00002310 00000000 00002314 00000000
v2: Move error collection to the ring error code
Change format of dump to not confuse intel_error_decode (Chris)
Put the context error object with the others (Chris)
Don't search bound_list instead of active_list (chris)
v3: extract and flatten context recording (daniel)
checkpatch related fixes for the copypasta in debugfs
v4: bug in v3 (Daniel)
- if ((ring->id == RCS) && error->ccid)
+ if ((ring->id != RCS) || !error->ccid)
References: https://bugs.freedesktop.org/show_bug.cgi?id=55845
Reviewed-by (v2): Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Bikeshed away the redudant parenthese around ring->id != RCS]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Actually use num_pages (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caching the PIPESTAT enable bits has been deemed pointless. Just
read them from the register itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The indentation is getting way too deep. Pull the vblank interupt
handling out to separate functions.
v2: Keep flip_mask handling in the main irq handler and
flatten {i8xx,i915}_handle_vblank() even further.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
