Add some debug messages for suspend/resume and to add a clear prefix to
s3c24xx-i2s and s3c24xx-pcm.
Signed-off-by: Tim Niemeyer <reddog@mastersword.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The irq handler of PCI drivers must be released before releasing other
resources since the handler for a shared irq can be still called and
may access the freed resource again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Tim Niemeyer <reddog@mastersword.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PXA3xx does not support the use of interrupts during reset and access
to the GPIO status requires similar handling to that for PXA27x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct some arguments in calls to snd_ice1712_gpio_write_bits() from
ap192_set_rate_val().
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some calls to snd_ice1712_gpio_write() go wrong, if
snd_ice1712_gpio_write_bits() ran before and changed the gpio mask register.
Read the actual gpio value and combine it with the to be set bits in the cpu
instead.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let "chip reset" become first. Increasement of the "chip reset" related timeout
leads to correctly read eeprom's contents here.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since unsigned active_offs < 0 is even true when DMAbuf_get_buffer_pointer()
returns negative
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs4270_hw_params does several times:
ret = snd_soc_write()
if (ret < 0)
...
This only works when ret is signed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the race at reconnection of the device.
The disconnected usb_chip[] must be cleared before the next probe
call properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A little clean up of snd_card_free*().
Removed snd_card_free_prepare() since it's actually almost identical
with snd_card_disconnect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the call of device_unregister() for the card instance in
snd_card_disconnect() to avoid the race of sysfs card entry, which
can be typically found on usb-audio reconnection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add mixer controls and correct headphone detection bits for PowerMac
G3 B&W and iMac G3 Tray-loading, both having Burgundy chipset.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable port change interrupt while initialising AWACS, Screamer, and
Burgundy chipsets.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
bps is unsigned, a negative snd_pcm_format_width() return value is not noticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last ALC889A hack may break on some devices with certain model presets
since patch_alc*() have different model tables. So, now it's handled in
the original patch_alc882() but fly to patch_alc883() in model=auto
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several 92hd7xxx and STAC9228 laptops have multiple headphone jacks,
the second headphone jack should be used for the 5.1 surround sound.
Add support for 'Headphone as Line Out' switch, which allows it be used
in 5.1 surround sound.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a pointer for DAC volume TLV data to the model structure so that the
model driver do not need to manually assign it in their control filter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add fields for the DAC volume limits to the module structure so that
model drivers do not need to install their own control info handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The empty hifier_mixer_init() function is useless; remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of AD1989A and AD1989B codecs.
These codecs can have multiple SPDIF devices, but currently we handle
only one SPDIF. If any real devices with two SPDIF interfaces (likely
one for SPDIF and one for HDMI), we'll fix this rightly.
Otherwise, these codecs are pretty similar with AD1988.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the GPIO 1 mixer control to enable I/O through the front panel
connector of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch for snd_usb_caiaq makes sample rates higher dann 48KHz work
with devices which have more than 2 stereo input/output pairs.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch corrects the input channel order of hardware supported by
snd_usb_caiaq.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes potential lockups in snd_usb_caiaq by refining the
locking mechanims and by using usb_kill_urb() in favor to
usb_unlink_urb().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Leave the power bit for the touch screen alone when suspending the WM9713
so that the touch screen driver can handle it. This allows the touch
screen to be used as a wakeup source when the system is suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound: kernel log levels are 0-7
Kernel log levels are 0-7, not 0-9.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds support for Quanta IL1 mini-notebook to alsa, defining a new model
for it. It comes with an ALC267 codec chip. Some notes about this model:
* In headphone automute, I use AC_VERB_SET_PIN_WIDGET_CONTROL instead of common
amp mute, to avoid conflict with mixer switch (mixer and automute use the
same nid).
* The only connected capture sources in the hardware are the internal mic and
external mic jack. So instead of using an input source selector like on other
ALC268 models, the mic automute automatically switch between captures.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable sound
platform drivers, to re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management support for EAPD enabled laptops, when headphones
are sensed it pulls the EAPD GPIO line low to power it down.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several laptops have have the SPDIF out defined as 'Digital other out'
when it should be 'SPDIF out' in the default config.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The legacy PC speaker signal was not routed to outputs. The codec is not
prevented from powering down in this patch, although I suppose one could
argue that perhaps it should be. Let me know if anyone feels strongly one
way or the other.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Please refer to [0003874] on the alsa mantis.
This patch added the pci quirk.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To mute the output of Pin widget 15 in ALC880, we should use the
HDA_OUTPUT. However, current code looks like :
snd_hda_codec_amp_stereo(codec, 0x15, HDA_INPUT, 0, HDA_AMP_MUTE, bits);
It may be a misspelling.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Putting space between ! and variable is a strange coding style, fix
that, also make it fit into 80 columns where that is easy.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb audio contains useful debugging code, protected by #if
0. Unfortunately, it will not compile because variable names changed;
fix it.
Dallas workaround is formatted in a way where it is not quite obvious
what is normal code and what is quirk. Reformat it to make it obvious.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dallas USB speakers are buggy in more than one way. One of configs
they offer does not work at all.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
WARNING: braces {} are not necessary for single statement blocks
#40: FILE: sound/pci/es1968.c:1831:
+ if (diff > 1) {
+ __maestro_write(chip, IDR0_DATA_PORT, cp1);
+ }
total: 0 errors, 1 warnings, 35 lines checked
./patches/es1968-fix-jitter-on-some-maestro-cards.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Andreas Mueller <andreas@stapelspeicher.org>
Tested-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch suppresses jitter on several Maestro cards in stereo mode (ALSA of
course).
The patch is also incorporated in the *BSD drivers where I "ported" it from.
Without this patch most of the stereo audio gets out of sync and really
distorted (oss-emulation with mplayer at 48000khz worked somehow).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/rme9652/hdspm.c has unusually large number of static inline
functions - 22.
I looked through them and some of them seem to be too big to warrant inlining.
This patch removes "inline" from these static functions (regardless of number
of callsites - gcc nowadays auto-inlines statics with one callsite).
Size difference on 32bit x86:
text data bss dec hex filename
20437 2160 516 23113 5a49 linux-2.6-ALLYES/sound/pci/rme9652/hdspm.o
18036 2160 516 20712 50e8 linux-2.6.inline-ALLYES/sound/pci/rme9652/hdspm.o
[coding fix by Takashi Iwai <tiwai@suse.de>]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When logging register changes in DAPM debug output include the register
number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Please refer to [0003848] on the alsa mantis.
This patch adds the pci quirk and Mic-Int controller.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Xonar DX, initialize all bits of the two-wire control register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control for switching whatever it is that is connected to
GPIO pin 1 on the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the card model does not have a digital input or an AC97 codec,
disable the respective interrupt and mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When selecting the capture source on the Xonar DX, the input jack must
be routed to either the line input or the microphone input by setting a
GPIO pin. This requires an additional callback so that the model driver
can hook into the toggling of AC97 switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the card short name to show to show the card name instead of the
chip name.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When playing data at 96 kHz or higher, reduce the DAC oversampling rate
to 32.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the code that is common to all Xonar models to a separate function,
and make it more generic in preparation for another model.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename all CS5381 symbols to CS53x1 because they can also be used for
Xonar models with a CS5361.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use separate model structures for the D2 and D2X so that the init
function does not have to check for the model again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"GPL 2" does not mean that there have to be two MODULE_LICENSE("GPL")
entries. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for mic automute in clevo-m720r ALC883 model, and rename it
to more generic clevo-m720. Also change model entry in ALSA-Configuration.txt
accordingly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Forgot one more: 3stack-hp model also have now the same mixer as
3stack-6ch (after DAC assignment fix in ALC883), so use it avoiding
duplicating the same mixer definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, alc888_6st_dell_mixer is now the
same as alc883_base_mixer. Avoid duplicated code and use
alc883_base_mixer in 6stack-dell model, removing alc888_6st_dell_mixer
definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, the 6stack-hp model is now the same
as 6stack-dig. So just remove 6stack-hp model and replace its use with
6stack-dig.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* moving most of clock-specific code to card-specific routines
* support for ESI Juli
* to-be-researched - monitoring of analog/digital inputs
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc64:
sound/pci/pcxhr/pcxhr.c: In function `pcxhr_update_r_buffer':
sound/pci/pcxhr/pcxhr.c:459: warning: cast to pointer from integer of different size
sound/pci/pcxhr/pcxhr.c: In function `pcxhr_trigger_tasklet':
sound/pci/pcxhr/pcxhr.c:628: warning: long int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/pcxhr/pcxhr_core.c: In function `pcxhr_set_pipe_state':
sound/pci/pcxhr/pcxhr_core.c:899: warning: long int format, different type arg (arg 4)
suseconds_t is int on sparc64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/aw2/aw2-alsa.c: In function 'snd_aw2_create':
sound/pci/aw2/aw2-alsa.c:282: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
sound/pci/aw2/aw2-alsa.c:282: error: (Each undeclared identifier is reported only once
sound/pci/aw2/aw2-alsa.c:282: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disable the master clock outputs of any unused I2S inputs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When specifying which PCM devices to use, model drivers now use flags
that also specify the routing between PCM devices and DMA channels
instead of just DMA channel bits. This simplifies some code that checks
for these flags.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add controls to enable monitoring of the analog and digital inputs.
To allow monitoring after loading the driver when nothing has been
played back or recorded yet, the I2S input and outputs are initialized
to a valid configuration.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the PCM1796 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the WM8786 register symbol definitions to their own header file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With commit 9004acc70e, include/sound/driver.h
is deprecated. This patch removes the #include from fsl_ssi.c and fsl_dma.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep the format verb at closing PCM streams.
Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/drivers/pcsp/pcsp.c: In function 'snd_pcsp_create':
sound/drivers/pcsp/pcsp.c:54: error: 'loops_per_jiffy' undeclared (first use in\ this function)
sound/drivers/pcsp/pcsp.c:54: error: (Each undeclared identifier is reported on\ ly once
sound/drivers/pcsp/pcsp.c:54: error: for each function it appears in.)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt handler always provide runtime->period_size data, so it
works correctly only if buffer_size was a multiple of period_size.
This patch fixes periodic click noise.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable is_capture is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to have snd_card_set_dev() in _probe(), but not a second one in
snd_ml403_ac97cr_create().
Signed-off-by: Joachim Foerster <JOFT@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AK4114 on Juli@ has the SPDIF input sample rate detection and
causes errors when an incompatible sample rate is chosen.
The patch adds the open hook to check the current rate and limit
the hw constraints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver has a problem at power-off on ASUS P5AD2.
It's caused when the position-buffer is enabled -- most likely a
hardware-specific problem.
This patch adds a quirk to avoid the unnecessary enablement of
position-buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the headphone controls are created as Master wrongly in
some cases, and this prevents the virtual master controls.
The patch fixes the problem by simply using "Headphone" always for
headphone controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed issue on some laptops that if the Master mixer and DAC mixers are
turned all the way up that will cause distortion. This is fixed by limiting
the max volume with the volume knob nid.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_lib_preallocate_free_for_all() is called from snd_pcm_free() just
after calling the private_free routine. So there should be no need to call
it in driver's private_free routine.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
aw2-tsl.h should be rather a C file to be included since it's referred
only in aw2-saa6146.c and includes a table data.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changed so that internal speakers point to the Front mixer instead of Surround.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for monaural playback to at73c213 driver. The sound will be apear
on L-channel. Tested on AT91SAM9260-EK.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The clk_round_rate() and clk_set_rate() will return int, so not store thier
return value to unsigned long variable. This bug hides real error on these
API.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
if (...) BUG(); should be replaced with BUG_ON(...) when the test has no
side-effects to allow a definition of BUG_ON that drops the code completely.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ disable unlikely @ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (unlikely(E)) { BUG(); }
+ BUG_ON(E);
)
@@ expression E,f; @@
(
if (<... f(...) ...>) { BUG(); }
|
- if (E) { BUG(); }
+ BUG_ON(E);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the Device IDs of nvidia MCP79 HD audio controller to hda_intel.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the model laptop-hpsense use the 0x12 as ExtMic,
and use 0x14 as Internal IntMic.
But the hp530 only have one ExtMic, the Pin widget is 0x14.
In this patch, I changed the mixer item for them.
I still reserved the IntMic item, it will be helpful if
other machine may use this model.
ALSA bug#3821.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- make pcsp_start_timer_tasklet static
- remove redundant includes. <asm/i8253.h> is not available on all platforms.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/hda/hda_intel.c: In function 'azx_create':
sound/pci/hda/hda_intel.c:1838: error: 'DMA_64BIT_MASK' undeclared (first use in this function)
sound/pci/hda/hda_intel.c:1838: error: (Each undeclared identifier is reported only once
sound/pci/hda/hda_intel.c:1838: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
GTA02 device has a speaker between LOUT2 & ROUT2 and in this mode ROUT2
needs to be inverted. This patch adds a mixer control for this.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added core_init[] for several 92hd73xxx laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management can't be enabled on fixed ports, since the presence
will always return false and prevent output.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Temp variable in the loop shadows the second argument (which is otherwise
unused in this function). Change this to defcfg as it is used to hold
the default config.
sound/pci/hda/patch_sigmatel.c:2759:18: warning: symbol 'cfg' shadows an earlier one
sound/pci/hda/patch_sigmatel.c:2734:26: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
