Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.
HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is being deleted, "/proc/net/dev_snmp6/<interface name>"
is deleted.
The function for this is addrconf_ifdown() in the addrconf_notify() and
it is called by notification, which is NETDEV_UNREGISTER.
But, if NETDEV_CHANGEMTU is triggered after NETDEV_UNREGISTER,
this proc file will be created again.
This recreated proc file will be deleted by netdev_wati_allrefs().
Before netdev_wait_allrefs() is called, creating a new HSR interface
routine can be executed and It tries to create a proc file but it will
find an un-deleted proc file.
At this point, it warns about it.
To avoid this situation, it can use ->dellink() instead of
->ndo_uninit() to release resources because ->dellink() is called
before NETDEV_UNREGISTER.
So, a proc file will not be recreated.
Test commands
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 mtu 1300
#SHELL1
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
done
#SHELL2
while :
do
ip link del hsr0
done
Splat looks like:
[ 9888.980852][ T2752] proc_dir_entry 'dev_snmp6/hsr0' already registered
[ 9888.981797][ C2] WARNING: CPU: 2 PID: 2752 at fs/proc/generic.c:372 proc_register+0x2d5/0x430
[ 9888.981798][ C2] Modules linked in: hsr dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6x
[ 9888.981814][ C2] CPU: 2 PID: 2752 Comm: ip Tainted: G W 5.8.0-rc1+ #616
[ 9888.981815][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 9888.981816][ C2] RIP: 0010:proc_register+0x2d5/0x430
[ 9888.981818][ C2] Code: fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 65 01 00 00 49 8b b5 e0 00 00 00 48 89 ea 40
[ 9888.981819][ C2] RSP: 0018:ffff8880628dedf0 EFLAGS: 00010286
[ 9888.981821][ C2] RAX: dffffc0000000008 RBX: ffff888028c69170 RCX: ffffffffaae09a62
[ 9888.981822][ C2] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f75ac
[ 9888.981823][ C2] RBP: ffff888028c693f4 R08: ffffed100d9401bd R09: ffffed100d9401bd
[ 9888.981824][ C2] R10: ffffffffaddf406f R11: 0000000000000001 R12: ffff888028c69308
[ 9888.981825][ C2] R13: ffff8880663584c8 R14: dffffc0000000000 R15: ffffed100518d27e
[ 9888.981827][ C2] FS: 00007f3876b3b0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 9888.981828][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9888.981829][ C2] CR2: 00007f387601a8c0 CR3: 000000004101a002 CR4: 00000000000606e0
[ 9888.981830][ C2] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9888.981831][ C2] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9888.981832][ C2] Call Trace:
[ 9888.981833][ C2] ? snmp6_seq_show+0x180/0x180
[ 9888.981834][ C2] proc_create_single_data+0x7c/0xa0
[ 9888.981835][ C2] snmp6_register_dev+0xb0/0x130
[ 9888.981836][ C2] ipv6_add_dev+0x4b7/0xf60
[ 9888.981837][ C2] addrconf_notify+0x684/0x1ca0
[ 9888.981838][ C2] ? __mutex_unlock_slowpath+0xd0/0x670
[ 9888.981839][ C2] ? kasan_unpoison_shadow+0x30/0x40
[ 9888.981840][ C2] ? wait_for_completion+0x250/0x250
[ 9888.981841][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981842][ C2] ? dropmon_net_event+0x227/0x410
[ 9888.981843][ C2] ? notifier_call_chain+0x90/0x160
[ 9888.981844][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981845][ C2] notifier_call_chain+0x90/0x160
[ 9888.981846][ C2] register_netdevice+0xbe5/0x1070
[ ... ]
Reported-by: syzbot+1d51c8b74efa4c44adeb@syzkaller.appspotmail.com
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hsr_dev_change_mtu(), the 'dev' and 'master->dev' pointer are
same. So, the 'master' variable and some code are unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Splat looks like:
[ 236.066091][ T3286] list_add corruption. next->prev should be prev (ffff8880a5940300), but was ffff8880a5940d0.
[ 236.069617][ T3286] ------------[ cut here ]------------
[ 236.070545][ T3286] kernel BUG at lib/list_debug.c:25!
[ 236.071391][ T3286] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 236.072343][ T3286] CPU: 0 PID: 3286 Comm: arping Tainted: G W 5.5.0-rc1+ #209
[ 236.073463][ T3286] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 236.074695][ T3286] RIP: 0010:__list_add_valid+0x74/0xd0
[ 236.075499][ T3286] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 b
[ 236.078277][ T3286] RSP: 0018:ffff8880aaa97648 EFLAGS: 00010286
[ 236.086991][ T3286] RAX: 0000000000000075 RBX: ffff8880d4624c20 RCX: 0000000000000000
[ 236.088000][ T3286] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed1015552ebf
[ 236.098897][ T3286] RBP: ffff88809b53d200 R08: ffffed101b3c04f9 R09: ffffed101b3c04f9
[ 236.099960][ T3286] R10: 00000000308769a1 R11: ffffed101b3c04f8 R12: ffff8880d4624c28
[ 236.100974][ T3286] R13: ffff8880d4624c20 R14: 0000000040310100 R15: ffff8880ce17ee02
[ 236.138967][ T3286] FS: 00007f23479fa680(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 236.144852][ T3286] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 236.145720][ T3286] CR2: 00007f4a14bab210 CR3: 00000000a61c6001 CR4: 00000000000606f0
[ 236.146776][ T3286] Call Trace:
[ 236.147222][ T3286] hsr_add_node+0x314/0x490 [hsr]
[ 236.153633][ T3286] hsr_forward_skb+0x2b6/0x1bc0 [hsr]
[ 236.154362][ T3286] ? rcu_read_lock_sched_held+0x90/0xc0
[ 236.155091][ T3286] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 236.156607][ T3286] hsr_dev_xmit+0x70/0xd0 [hsr]
[ 236.157254][ T3286] dev_hard_start_xmit+0x160/0x740
[ 236.157941][ T3286] __dev_queue_xmit+0x1961/0x2e10
[ 236.158565][ T3286] ? netdev_core_pick_tx+0x2e0/0x2e0
[ ... ]
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching from ->priv_destructor to dellink() has an unexpected
consequence: existing RCU readers, that is, hsr_port_get_hsr()
callers, may still be able to read the port list.
Instead of checking the return value of each hsr_port_get_hsr(),
we can just move it to ->ndo_uninit() which is called after
device unregister and synchronize_net(), and we still have RTNL
lock there.
Fixes: b9a1e62740 ("hsr: implement dellink to clean up resources")
Fixes: edf070a0fb ("hsr: fix a NULL pointer deref in hsr_dev_xmit()")
Reported-by: syzbot+097ef84cdc95843fbaa8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_link_ops implements ->newlink() but not ->dellink(),
which leads that resources not released after removing the device,
particularly the entries in self_node_db and node_db.
So add ->dellink() implementation to replace the priv_destructor.
This also makes the code slightly easier to understand.
Reported-by: syzbot+c6167ec3de7def23d1e8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_del_port() should release all the resources allocated
in hsr_add_port().
As a consequence of this change, hsr_for_each_port() is no
longer safe to work with hsr_del_port(), switch to
list_for_each_entry_safe() as we always hold RTNL lock.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the path of hsr debugfs root directory to use the net device
name so that it can work with multiple interfaces. While at it,
also fix some typos.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the file name and functions to match with existing implementation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a debugfs interface to allow display the nodes learned
by the hsr master.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver code uses camel case in many places. This is
seen when ran checkpatch.pl -f on files under net/hsr. This
patch fixes the code to remove camel case usage.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all instance of NULL checks such as
if (foo == NULL) with if (!foo)
Also
if (foo != NULL) with if (foo)
This is seen when ran checkpatch.pl -f on files under net/hsr
and suggestion is to replace as above.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes function calls that ends with '(' in a line.
This is seen when ran checkpatch.pl -f option on files under
net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes alignment issues in code for functions. This is
seen when ran checkpatch.pl -f option on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes unnecessary paranthesis from the code. This is
seen when ran checkpatch.pl -f option on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple blank lines in the code. This is seen
when ran checkpatch.pl -f option for files under net/hsr
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() will free the sk_buff passed as reference in case of
errors, but we still need to check its return value and decide what to
do.
Detected by CoverityScan, CID#1416688 ("CHECKED_RETURN")
Fixes: ee1c279772 ("net/hsr: Added support for HSR v1")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make sure
dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function setup_timer combines the initialization of a timer with the
initialization of the timer's function and data fields. The mulitiline
code for timer initialization is now replaced with function setup_timer.
Also, quoting the mod_timer() function comment:
-> mod_timer() is a more efficient way to update the expire field of an
active timer (if the timer is inactive it will be activated).
Use setup_timer() and mod_timer() to setup and arm a timer, making the
code compact and aid readablity.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.
Main changes are in the supervision frame handling and its
ethertype field.
Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARN_ON_ONCE() takes a condition, it doesn't take an error message. I
have converted this to WARN() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To repeat:
$ sudo ip link del hsr0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff8187f495>] hsr_del_port+0x15/0xa0
etc...
Bug description:
As part of the hsr master device destruction, hsr_del_port() is called for each of
the hsr ports. At each such call, the master device is updated regarding features
and mtu. When the master device is freed before the slave interfaces, master will
be NULL in hsr_del_port(), which led to a NULL pointer dereference.
Additionally, dev_put() was called on the master device itself in hsr_del_port(),
causing a refcnt error.
A third bug in the same code path was that the rtnl lock was not taken before
hsr_del_port() was called as part of hsr_dev_destroy().
The reporter (Nicolas Dichtel) also said: "hsr_netdev_notify() supposes that the
port will always be available when the notification is for an hsr interface. It's
wrong. For example, netdev_wait_allrefs() may resend NETDEV_UNREGISTER.". As a
precaution against this, a check for port == NULL was added in hsr_dev_notify().
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: 51f3c60531 ("net/hsr: Move slave init to hsr_slave.c.")
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
