It actually means create here, so fix the typo.
Reported-by: Song Liu <liu.song.a23@gmail.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Previously, wb_info_pool and wb_list stuffs are introduced
to address potential data inconsistence issue for write
behind device.
Now rename them to serial related name, since the same
mechanism will be used to address reorder overlap write
issue for raid1.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
For super_90_load, we need to make sure 'desc_nr' less
than MD_SB_DISKS, avoiding invalid memory access of 'sb->disks'.
Fixes: 228fc7d76d ("md: avoid invalid memory access for array sb->dev_roles")
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
we need to gurantee 'desc_nr' valid before access array
of sb->dev_roles.
In addition, we should avoid .load_super always return '0'
when level is LEVEL_MULTIPATH, which is not expected.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1487373 ("Memory - illegal accesses")
Fixes: 6a5cb53aaa ("md: no longer compare spare disk superblock events in super_load")
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
We have a test case as follow:
mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] \
--assume-clean --bitmap=internal
mdadm -S /dev/md1
mdadm -A /dev/md1 /dev/sd[b-c] --run --force
mdadm --zero /dev/sda
mdadm /dev/md1 -a /dev/sda
echo offline > /sys/block/sdc/device/state
echo offline > /sys/block/sdb/device/state
sleep 5
mdadm -S /dev/md1
echo running > /sys/block/sdb/device/state
echo running > /sys/block/sdc/device/state
mdadm -A /dev/md1 /dev/sd[a-c] --run --force
When we readd /dev/sda to the array, it started to do recovery.
After offline the other two disks in md1, the recovery have
been interrupted and superblock update info cannot be written
to the offline disks. While the spare disk (/dev/sda) can continue
to update superblock info.
After stopping the array and assemble it, we found the array
run fail, with the follow kernel message:
[ 172.986064] md: kicking non-fresh sdb from array!
[ 173.004210] md: kicking non-fresh sdc from array!
[ 173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[ 173.022406] md1: failed to create bitmap (-5)
[ 173.023466] md: md1 stopped.
Since both sdb and sdc have the value of 'sb->events' smaller than
that in sda, they have been kicked from the array. However, the only
remained disk sda is in 'spare' state before stop and it cannot be
added to conf->mirrors[] array. In the end, raid array assemble
and run fail.
In fact, we can use the older disk sdb or sdc to assemble the array.
That means we should not choose the 'spare' disk as the fresh disk in
analyze_sbs().
To fix the problem, we do not compare superblock events when it is
a spare disk, as same as validate_super.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
If pers->make_request fails in md_flush_request(), the bio is lost. To
fix this, pass back a bool to indicate if the original make_request call
should continue to handle the I/O and instead of assuming the flush logic
will push it to completion.
Convert md_flush_request to return a bool and no longer calls the raid
driver's make_request function. If the return is true, then the md flush
logic has or will complete the bio and the md make_request call is done.
If false, then the md make_request function needs to keep processing like
it is a normal bio. Let the original call to md_handle_request handle any
need to retry sending the bio to the raid driver's make_request function
should it be needed.
Also mark md_flush_request and the make_request function pointer as
__must_check to issue warnings should these critical return values be
ignored.
Fixes: 2bc13b83e6 ("md: batch flush requests.")
Cc: stable@vger.kernel.org # # v4.19+
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Due to a bug introduced in Linux 3.14 we cannot determine the
correctly layout for a multi-zone RAID0 array - there are two
possibilities.
It is possible to tell the kernel which to chose using a module
parameter, but this can be clumsy to use. It would be best if
the choice were recorded in the metadata.
So add a feature flag for this purpose.
If it is set, then the 'layout' field of the superblock is used
to determine which layout to use.
If this flag is not set, then mddev->layout gets set to -1,
which causes the module parameter to be required.
Acked-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
Currently md raid0/linear are not provided with any mechanism to validate
if an array member got removed or failed. The driver keeps sending BIOs
regardless of the state of array members, and kernel shows state 'clean'
in the 'array_state' sysfs attribute. This leads to the following
situation: if a raid0/linear array member is removed and the array is
mounted, some user writing to this array won't realize that errors are
happening unless they check dmesg or perform one fsync per written file.
Despite udev signaling the member device is gone, 'mdadm' cannot issue the
STOP_ARRAY ioctl successfully, given the array is mounted.
In other words, no -EIO is returned and writes (except direct ones) appear
normal. Meaning the user might think the wrote data is correctly stored in
the array, but instead garbage was written given that raid0 does stripping
(and so, it requires all its members to be working in order to not corrupt
data). For md/linear, writes to the available members will work fine, but
if the writes go to the missing member(s), it'll cause a file corruption
situation, whereas the portion of the writes to the missing devices aren't
written effectively.
This patch changes this behavior: we check if the block device's gendisk
is UP when submitting the BIO to the array member, and if it isn't, we flag
the md device as MD_BROKEN and fail subsequent I/Os to that device; a read
request to the array requiring data from a valid member is still completed.
While flagging the device as MD_BROKEN, we also show a rate-limited warning
in the kernel log.
A new array state 'broken' was added too: it mimics the state 'clean' in
every aspect, being useful only to distinguish if the array has some member
missing. We rely on the MD_BROKEN flag to put the array in the 'broken'
state. This state cannot be written in 'array_state' as it just shows
one or more members of the array are missing but acts like 'clean', it
wouldn't make sense to write it.
With this patch, the filesystem reacts much faster to the event of missing
array member: after some I/O errors, ext4 for instance aborts the journal
and prevents corruption. Without this change, we're able to keep writing
in the disk and after a machine reboot, e2fsck shows some severe fs errors
that demand fixing. This patch was tested in ext4 and xfs filesystems, and
requires a 'mdadm' counterpart to handle the 'broken' state.
Cc: Song Liu <songliubraving@fb.com>
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Until revalidate_disk() has completed, the size of a new md array will
appear to be zero.
So we shouldn't report, through array_state, that the array is active
until that time.
udev rules check array_state to see if the array is ready. As soon as
it appear to be zero, fsck can be run. If it find the size to be
zero, it will fail.
So add a new flag to provide an interlock between do_md_run() and
array_state_show(). This flag is set while do_md_run() is active and
it prevents array_state_show() from reporting that the array is
active.
Before do_md_run() is called, ->pers will be NULL so array is
definitely not active.
After do_md_run() is called, revalidate_disk() will have run and the
array will be completely ready.
We also move various sysfs_notify*() calls out of md_run() into
do_md_run() after MD_NOT_READY is cleared. This ensure the
information is ready before the notification is sent.
Prior to v4.12, array_state_show() was called with the
mddev->reconfig_mutex held, which provided exclusion with do_md_run().
Note that MD_NOT_READY cleared twice. This is deliberate to cover
both success and error paths with minimal noise.
Fixes: b7b17c9b67 ("md: remove mddev_lock() from md_attr_show()")
Cc: stable@vger.kernel.org (v4.12++)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Since commit 4ad23a9764 ("MD: use per-cpu counter for
writes_pending"), set_in_sync() is substantially more expensive: it
can wait for a full RCU grace period which can be 10s of milliseconds.
So we should only call it when the cost is justified.
md_check_recovery() currently calls set_in_sync() every time it finds
anything to do (on non-external active arrays). For an array
performing resync or recovery, this will be quite often.
Each call will introduce a delay to the md thread, which can noticeable
affect IO submission latency.
In md_check_recovery() we only need to call set_in_sync() if
'safemode' was non-zero at entry, meaning that there has been not
recent IO. So we save this "safemode was nonzero" state, and only
call set_in_sync() if it was non-zero.
This measurably reduces mean and maximum IO submission latency during
resync/recovery.
Reported-and-tested-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Cc: stable@vger.kernel.org (v4.12+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().
But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.
So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When a disk is added to array, the following path is called in mdadm.
Manage_subdevs -> sysfs_freeze_array
-> Manage_add
-> sysfs_set_str(&info, NULL, "sync_action","idle")
Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.
Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When the 'last' device in a RAID1 or RAID10 reports an error,
we do not mark it as failed. This would serve little purpose
as there is no risk of losing data beyond that which is obviously
lost (as there is with RAID5), and there could be other sectors
on the device which are readable, and only readable from this device.
This in general this maximises access to data.
However the current implementation also stops an admin from removing
the last device by direct action. This is rarely useful, but in many
case is not harmful and can make automation easier by removing special
cases.
Also, if an attempt to write metadata fails the device must be marked
as faulty, else an infinite loop will result, attempting to update
the metadata on all non-faulty devices.
So add 'fail_last_dev' member to 'struct mddev', then we can bypasses
the 'last disk' checks for RAID1 and RAID10, and control the behavior
per array by change sysfs node.
Signed-off-by: NeilBrown <neilb@suse.de>
[add sysfs node for fail_last_dev by Guoqing]
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Pull percpu updates from Dennis Zhou:
"This includes changes to let percpu_ref release the backing percpu
memory earlier after it has been switched to atomic in cases where the
percpu ref is not revived.
This will help recycle percpu memory earlier in cases where the
refcounts are pinned for prolonged periods of time"
* 'for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu_ref: release percpu memory early without PERCPU_REF_ALLOW_REINIT
md: initialize percpu refcounters using PERCU_REF_ALLOW_REINIT
io_uring: initialize percpu refcounters using PERCU_REF_ALLOW_REINIT
percpu_ref: introduce PERCPU_REF_ALLOW_REINIT flag
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into for-5.3/block
Merge 5.2-rc6 into for-5.3/block, so we get the same page merge leak
fix. Otherwise we end up having conflicts with future patches between
for-5.3/block and master that touch this area. In particular, it makes
the bio_full() fix hard to backport to stable.
* tag 'v5.2-rc6': (482 commits)
Linux 5.2-rc6
Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"
Bluetooth: Fix regression with minimum encryption key size alignment
tcp: refine memory limit test in tcp_fragment()
x86/vdso: Prevent segfaults due to hoisted vclock reads
SUNRPC: Fix a credential refcount leak
Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
net :sunrpc :clnt :Fix xps refcount imbalance on the error path
NFS4: Only set creation opendata if O_CREAT
ARM: 8867/1: vdso: pass --be8 to linker if necessary
KVM: nVMX: reorganize initial steps of vmx_set_nested_state
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
habanalabs: use u64_to_user_ptr() for reading user pointers
nfsd: replace Jeff by Chuck as nfsd co-maintainer
inet: clear num_timeout reqsk_alloc()
PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
...
Now, there are two places need to consider about
the failure of destroy bitmap, so move the common
part between bitmap_abort and abort label.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Previously, we called rdev_init_wb to avoid potential data
inconsistency when array is created.
Now, we need to call the function and create mempool if a
device is added or just be flaged as "writemostly". So
mddev_create_wb_pool is introduced and called accordingly.
And for safety reason, we mark implicit GFP_NOIO allocation
scope for create mempool during mddev_suspend/mddev_resume.
And mempool should be removed conversely after remove a
member device or its's "writemostly" flag, which is done
by call mddev_destroy_wb_pool.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
For write-behind mode, we think write IO is complete once it has
reached all the non-writemostly devices. It works fine for single
queue devices.
But for multiqueue device, if there are lots of IOs come from upper
layer, then the write-behind device could issue those IOs to different
queues, depends on the each queue's delay, so there is no guarantee
that those IOs can arrive in order.
To address the issue, we need to check the collision among write
behind IOs, we can only continue without collision, otherwise wait
for the completion of previous collisioned IO.
And WBCollision is introduced for multiqueue device which is worked
under write-behind mode.
But this patch doesn't handle below cases which could have the data
inconsistency issue as well, these cases will be handled in later
patches.
1. modify max_write_behind by write backlog node.
2. add or remove array's bitmap dynamically.
3. the change of member disk.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
This patch fix a spelling typo and add necessary space for code.
In addition, the patch get rid of the unnecessary 'if'.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit c42d324099
("md: return -ENODEV if rdev has no mddev assigned") changed
rdev_attr_store to return -ENODEV when rdev->mddev is NULL, now do the
same to rdev_attr_show.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version you should have received a copy of the gnu general
public license for example usr src linux copying if not write to the
free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 20 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Percpu reference counters should now be initialized with the
PERCPU_REF_ALLOW_REINIT in order to allow switching them to the
percpu mode from the atomic mode.
To make percpu_ref_switch_to_percpu() call in set_in_sync()
succeed,let's initialize percpu refcounters with the
PERCU_REF_ALLOW_REINIT flag.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Mdadm expects that setting drive as faulty will fail with -EBUSY only if
this operation will cause RAID to be failed. If this happens, it will
try to stop the array. Currently -EBUSY might also be returned if rdev
is in the middle of the removal process - for example there is a race
with mdmon that already requested the drive to be failed/removed.
If rdev does not contain mddev, return -ENODEV instead, so the caller
can distinguish between those two cases and behave accordingly.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Sparse complains that it has no external declaration, and it turns out
that it is never even used outside of md.c. So just mark it static
and drop the export.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If we want to convert from a little endian format we need to cast
to a little endian type, otherwise sparse will be unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If we want to convert from a little endian format we need to cast
to a little endian type, otherwise sparse will be unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
The on-disk value is little endian and we need to convert it to
native endian before storing the value in the in-core structure.
Fixes: 7564beda19 ("md-cluster/raid10: support add disk under grow mode")
Cc: <stable@vger.kernel.org> # 4.20+
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
When doing re-add, we need to ensure rdev->mddev->pers is not NULL,
which can avoid potential NULL pointer derefence in fallowing
add_bound_rdev().
Fixes: a6da4ef85c ("md: re-add a failed disk")
Cc: Xiao Ni <xni@redhat.com>
Cc: NeilBrown <neilb@suse.com>
Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 5a409b4f56.
This patch has two problems.
1/ it make multiple calls to submit_bio() from inside a make_request_fn.
The bios thus submitted will be queued on current->bio_list and not
submitted immediately. As the bios are allocated from a mempool,
this can theoretically result in a deadlock - all the pool of requests
could be in various ->bio_list queues and a subsequent mempool_alloc
could block waiting for one of them to be released.
2/ It aims to handle a case when there are many concurrent flush requests.
It handles this by submitting many requests in parallel - all of which
are identical and so most of which do nothing useful.
It would be more efficient to just send one lower-level request, but
allow that to satisfy multiple upper-level requests.
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_alloc_bioset returns a bio pointer or NULL, so we can avoid storing
the returned data into a new variable.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull the pending 4.21 changes for md from Shaohua.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
mempool_destroy() can handle NULL pointer correctly,
so there is no need to check NULL pointer before calling
mempool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/md/md.c: In function 'md_integrity_add_rdev':
drivers/md/md.c:2149:24: warning:
variable 'bi_rdev' set but not used [-Wunused-but-set-variable]
It not used any more after commit
1501efadc5 ("md/raid: only permit hot-add of compatible integrity profiles")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
All of part_stat_* and related methods are used with preempt disabled,
so there is no need to pass cpu around to allow of them. Just call
smp_processor_id() as needed.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
flush_pool is leaked when flush bio size is zero
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
I noticed kmemleak report memory leak when run create/stop
md in a loop, backtrace:
[<000000001ca975e7>] mempool_create_node+0x86/0xd0
[<0000000095576bcd>] md_run+0x1057/0x1410 [md_mod]
[<000000007b45c5fc>] do_md_run+0x15/0x130 [md_mod]
[<000000001ede9ec0>] md_ioctl+0x1f49/0x25d0 [md_mod]
[<000000004142cacf>] blkdev_ioctl+0x680/0xd00
The root cause is we alloc mddev->flush_pool and
mddev->flush_bio_pool in md_run, but from do_md_stop
will not call into md_stop but __md_stop, move the
mempool_destroy to __md_stop fixes the problem for me.
The bug was introduced in 5a409b4f56, the fixes should go to
4.18+
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to continue the reshaping if it was interrupted in
original node. So original node should call resync_bitmap
in case reshaping is aborted.
Then BITMAP_NEEDS_SYNC message is broadcasted to other nodes,
node which continues the reshaping should restart reshape from
mddev->reshape_position instead of from the first beginning.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
remove_and_add_spares is not needed if reshape is
happening in another node, because raid10_add_disk
called inside raid10_start_reshape would handle the
role changes of disk. Plus, remove_and_add_spares
can't deal with the role change due to reshape.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to change the capacity in all nodes after one node
finishs reshape. And as we did before, we can't change the
capacity directly in md_do_sync, instead, the capacity should
be only changed in update_size or received CHANGE_CAPACITY
msg.
So master node calls update_size after completes reshape in
md_reap_sync_thread, but we need to skip ops->update_size if
MD_CLOSING is set since reshaping could not be finish.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
For clustered raid10 scenario, we need to let all the nodes
know about that a new disk is added to the array, and the
reshape caused by add new member just need to be happened in
one node, but other nodes should know about the change.
Since reshape means read data from somewhere (which is already
used by array) and write data to unused region. Obviously, it
is awful if one node is reading data from address while another
node is writing to the same address. Considering we have
implemented suspend writes in the resyncing area, so we can
just broadcast the reading address to other nodes to avoid the
trouble.
For master node, it would call reshape_request then update sb
during the reshape period. To avoid above trouble, we call
resync_info_update to send RESYNC message in reshape_request.
Then from slave node's view, it receives two type messages:
1. RESYNCING message
Slave node add the address (where master node reading data from)
to suspend list.
2. METADATA_UPDATED message
Once slave nodes know the reshaping is started in master node,
it is time to update reshape position and call start_reshape to
follow master node's step. After reshape is done, only reshape
position is need to be updated, so the majority task of reshaping
is happened on the master node.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit d595567dc4 (MD: fix invalid stored role for a disk) broke linear
hotadd. Let's only fix the role for disks in raid1/10.
Based on Guoqing's original patch.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit 35bfc52187 ("md: allow metadata update while suspending.")
added support for allowing md_check_recovery() to still perform
metadata updates while the array is entering the 'suspended' state.
This is needed to allow the processes of entering the state to
complete.
Unfortunately, the patch doesn't really work. The test for
"mddev->suspended" at the start of md_check_recovery() means that the
function doesn't try to do anything at all while entering suspend.
This patch moves the code of updating the metadata while suspending to
*before* the test on mddev->suspended.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 35bfc52187 ("md: allow metadata update while suspending.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If we change the number of array's device after device is removed from array,
then add the device back to array, we can see that device is added as active
role instead of spare which we expected.
Please see the below link for details:
https://marc.info/?l=linux-raid&m=153736982015076&w=2
This is caused by that we prefer to use device's previous role which is
recorded by saved_raid_disk, but we should respect the new number of
conf->raid_disks since it could be changed after device is removed.
Reported-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Tested-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
Pull MD updates from Shaohua Li:
"A few MD fixes for 4.19-rc1:
- several md-cluster fixes from Guoqing
- a data corruption fix from BingJing
- other cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid5: fix data corruption of replacements after originals dropped
drivers/md/raid5: Do not disable irq on release_inactive_stripe_list() call
drivers/md/raid5: Use irqsave variant of atomic_dec_and_lock()
md/r5cache: remove redundant pointer bio
md-cluster: don't send msg if array is closing
md-cluster: show array's status more accurate
md-cluster: clear another node's suspend_area after the copy is finished
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand MD bitmap API is special case.
Adding 'md' prefix to it to avoid name space collision.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
