Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
-----BEGIN PGP SIGNATURE-----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=bEhk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db865 ("usb: dwc3: of-simple: reset host controller at suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAltewsEdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQaV8BAAziA9QIT6to7Zzd7t
tsfU3chXUS2t+fZ6drADdHHwJTvjCT4D9FbpYFSNC9lanSLB+IwQ6rZGglyyPh5P
DVcWObi8wR1+w8gcx+NL65XuzM/oM8Sx+zSA+3hV7H8A1ePikd+wFpXcZhY0zoLS
00BoAf66CvRvGAGX8e1HouL4LPs/V5vllxcObKLrzcziCNziLhAy1MkONAwSagvP
JA50nh0Jau6p/+inF/931oeixmVvTV0xJjqveIf6cVsyv9jNy+I53rFwVsaiSVLz
dvzrnPmzWbT4F1yuLgqXccd68FF4Zm+Vl+uHyzaZ7b8e1JK7ABg9a7Us6CjP9HXq
aw63hUKmrsTsTyLCWkoU6ypeCYJF3Et49pzicLRFOdXufWJLTRa0iNbgyf8gNOQt
K8igJZkmHnb4RByLITtHot3Qdpn2Mr+8Cu/H4TpqQBAKom6mxdwkfm4lojBzLoRn
IIr81yTJD00uqgQ40IeoFyV5zz4CqMti3GQX8QXO2wdbrKlaLCr4UDuu4llE2AJ9
1cYV8SMoC2yXaGsshe2dvCq4/lhxiOXPBNoR/GvtvXd84AXaYCsuphUhSGTybYLG
a3LO72mn4R8hAnqzh3+xyC4Irs9hgVJUKOD7fFn0ZPvCXgLUQIYRimIprEQ0EsCI
/lcdOwOheSGM9Fq5U/fcWDdZcmE=
=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
endpoint->maxpacket is not updated after setting the
usb_set_maxpacket_limit() on endpoint enable. The MaxPacketSize can be
different than the endpoint->maxpacket_limit.
DWC3 has been consistently using MaxPacketSize from the endpoint's
descriptor, so let's keep it consistent and use the MaxPacketSize from
the endpoint's descriptor instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.
Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:
drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.
Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.
Fixes: ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.
The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.
Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.
This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.
Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.
The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.
I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.
The good news it that all boards (*) use the same GPIOs.
This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.
*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef guards around these are wrong, resulting in warnings
in certain configurations:
drivers/usb/dwc3/dwc3-qcom.c:244:12: error: 'dwc3_qcom_resume' defined but not used [-Werror=unused-function]
static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
^~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:223:12: error: 'dwc3_qcom_suspend' defined but not used [-Werror=unused-function]
static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
This replaces the guards with __maybe_unused annotations to shut up
the warnings and give better compile time coverage.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
adds support for handling clocks and resets in the DWC3 core, so that for
platforms following the standard devicetree bindings this does not need
to be duplicated in all the different glue layers.
These changes intended for devicetree based platforms introduce an
uncoditional clk_bulk_get() in the core probe path. This leads to the
following error being logged on x86/ACPI systems:
[ 26.276783] dwc3 dwc3.3.auto: Failed to get clk 'ref': -2
This commits wraps the clk_bulk_get() in an if (dev->of_node) check so
that it only is done on devicetree instantiated devices, fixing this
error.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0 ("usb: dwc3: add generic OF glue layer")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a "#define DEBUG" was left in on the recent patch
landed for the Qualcomm DWC3 glue driver. Let's remove it.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix sparse warning
Fixes: 5f0b74e548 ("USB: dwc3: get extcon device by OF graph bindings")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.
No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>