Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-27
This patchset is a proposal of how the Traffic Control subsystem can
be used to offload the configuration of the Credit Based Shaper
(defined in the IEEE 802.1Q-2014 Section 8.6.8.2) into supported
network devices.
As part of this work, we've assessed previous public discussions
related to TSN enabling: patches from Henrik Austad (Cisco), the
presentation from Eric Mann at Linux Plumbers 2012, patches from
Gangfeng Huang (National Instruments) and the current state of the
OpenAVNU project (https://github.com/AVnu/OpenAvnu/).
Overview
========
Time-sensitive Networking (TSN) is a set of standards that aim to
address resources availability for providing bandwidth reservation and
bounded latency on Ethernet based LANs. The proposal described here
aims to cover mainly what is needed to enable the following standards:
802.1Qat and 802.1Qav.
The initial target of this work is the Intel i210 NIC, but other
controllers' datasheet were also taken into account, like the Renesas
RZ/A1H RZ/A1M group and the Synopsis DesignWare Ethernet QoS
controller.
Proposal
========
Feature-wise, what is covered here is the configuration interfaces for
HW implementations of the Credit-Based shaper (CBS, 802.1Qav). CBS is
a per-queue shaper. Given that this feature is related to traffic
shaping, and that the traffic control subsystem already provides a
queueing discipline that offloads config into the device driver (i.e.
mqprio), designing a new qdisc for the specific purpose of offloading
the config for the CBS shaper seemed like a good fit.
For steering traffic into the correct queues, we use the socket option
SO_PRIORITY and then a mechanism to map priority to traffic classes /
Tx queues. The qdisc mqprio is currently used in our tests.
As for the CBS config interface, this patchset is proposing a new
qdisc called 'cbs'. Its 'tc' cmd line is:
$ tc qdisc add dev IFACE parent ID cbs locredit N hicredit M sendslope S \
idleslope I
Note that the parameters for this qdisc are the ones defined by the
802.1Q-2014 spec, so no hardware specific functionality is exposed here.
Per-stream shaping, as defined by IEEE 802.1Q-2014 Section 34.6.1, is
not yet covered by this proposal.
v2: Merged patch 6 of the original series into patch 4 based on feedback
from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
two extra #include are not necessary in tcp.h
Remove them.
Fixes: 40304b2a15 ("bpf: BPF support for sock_ops")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading the CBS algorithm to the controller,
if supported. Drivers wanting to support CBS offload must implement
the .ndo_setup_tc callback and handle the TC_SETUP_CBS (introduced
here) type.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Henrik Austad <henrik@austad.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes an enumerated type for the ports, we can use them
directly instead of checking bitmaps, which is more consistent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to know if a port is of type user, dsa_is_normal_port checks
that the given port is not of type DSA nor CPU. This is not enough
because a port can be unused.
Without the previous fix, this caused the unused mv88e6xxx ports to be
configured in normal mode.
The ds->enabled_port_mask reports the user ports, so check this instead.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that sysctl_tcp_thin_dupack was not used, I deleted it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* follow-up fixes for the WoWLAN security issue, to fix a
partial TKIP key material problem and to use crypto_memneq()
* a change for better enforcement of FQ's memory limit
* a disconnect/connect handling fix, and
* a user rate mask validation fix
-----BEGIN PGP SIGNATURE-----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=6b1o
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
pull-request: mac80211 2017-10-25
Here are:
* follow-up fixes for the WoWLAN security issue, to fix a
partial TKIP key material problem and to use crypto_memneq()
* a change for better enforcement of FQ's memory limit
* a disconnect/connect handling fix, and
* a user rate mask validation fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0da4af00b2 ("ipv6: only update __use and lastusetime
once per jiffy at most"), updating the dst lastuse field is an
unlikely action: it happens at most once per jiffy, out of
potentially millions of calls per second.
Mark explicitly the code as such, and let the compiler generate
better code.
Note: gcc 7.2 and several older versions do actually generate
different - better - code when the unlikely() hint is in place,
avoid jump in the fast path and keeping better code locality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC protocol [1] relies on the use of a new TCP experimental
option [2, 3]. With this option, SMC capabilities are exchanged
between peers during the TCP three way handshake. This patch adds
support for this experimental option to TCP.
References:
[1] SMC-R Informational RFC: http://www.rfc-editor.org/info/rfc7609
[2] Shared Use of TCP Experimental Options RFC 6994:
https://tools.ietf.org/rfc/rfc6994.txt
[3] IANA ExID SMCR:
http://www.iana.org/assignments/tcp-parameters/tcp-parameters.xhtml#tcp-exids
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my first attempt to fix the lockdep splat, I forgot we could
enter inet_csk_route_req() with a freshly allocated request socket,
for which refcount has not yet been elevated, due to complex
SLAB_TYPESAFE_BY_RCU rules.
We either are in rcu_read_lock() section _or_ we own a refcount on the
request.
Correct RCU verb to use here is rcu_dereference_check(), although it is
not possible to prove we actually own a reference on a shared
refcount :/
In v2, I added ireq_opt_deref() helper and use in three places, to fix other
possible splats.
[ 49.844590] lockdep_rcu_suspicious+0xea/0xf3
[ 49.846487] inet_csk_route_req+0x53/0x14d
[ 49.848334] tcp_v4_route_req+0xe/0x10
[ 49.850174] tcp_conn_request+0x31c/0x6a0
[ 49.851992] ? __lock_acquire+0x614/0x822
[ 49.854015] tcp_v4_conn_request+0x5a/0x79
[ 49.855957] ? tcp_v4_conn_request+0x5a/0x79
[ 49.858052] tcp_rcv_state_process+0x98/0xdcc
[ 49.859990] ? sk_filter_trim_cap+0x2f6/0x307
[ 49.862085] tcp_v4_do_rcv+0xfc/0x145
[ 49.864055] ? tcp_v4_do_rcv+0xfc/0x145
[ 49.866173] tcp_v4_rcv+0x5ab/0xaf9
[ 49.868029] ip_local_deliver_finish+0x1af/0x2e7
[ 49.870064] ip_local_deliver+0x1b2/0x1c5
[ 49.871775] ? inet_del_offload+0x45/0x45
[ 49.873916] ip_rcv_finish+0x3f7/0x471
[ 49.875476] ip_rcv+0x3f1/0x42f
[ 49.876991] ? ip_local_deliver_finish+0x2e7/0x2e7
[ 49.878791] __netif_receive_skb_core+0x6d3/0x950
[ 49.880701] ? process_backlog+0x7e/0x216
[ 49.882589] __netif_receive_skb+0x1d/0x5e
[ 49.884122] process_backlog+0x10c/0x216
[ 49.885812] net_rx_action+0x147/0x3df
Fixes: a6ca7abe53 ("tcp/dccp: fix lockdep splat in inet_csk_route_req()")
Fixes: c92e8c02fe ("tcp/dccp: fix ireq->opt races")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <fengguang.wu@intel.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some features it is necessary to instrument reads and
writes separately, which is not possible with ACCESS_ONCE(). This
distinction is critical to correct operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, this doesn't handle comments, leaving references
to ACCESS_ONCE() instances which have been removed. As a preparatory
step, this patch converts netlink and netfilter code and comments to use
{READ,WRITE}_ONCE() consistently.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Westphal <fw@strlen.de>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-7-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Liljestrand <ishkamiel@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: "Reshetova, Elena" <elena.reshetova@intel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patch 'rtnetlink: bring NETDEV_CHANGELOWERSTATE event
process back to rtnetlink_event', bond_lower_state_changed would
generate NETDEV_CHANGEUPPER event which would send a notification
to userspace in rtnetlink_event.
There's no need to call rtmsg_ifinfo to send the notification
any more. So this patch is to remove it from these places after
bond_lower_state_changed.
Besides, after this, rtmsg_ifinfo is not needed to be exported.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sock lock may be taken in the message timer function which is a
problem since timers run in BH. Instead of timers use delayed_work.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: bbb03029a8 ("strparser: Generalize strparser")
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently pass down the l4 protocol to the conntrack ->packet()
function, but the only user of this is the debug info decision.
Same information can be derived from struct nf_conn.
Add a wrapper for the previous patch that extracs the information
from nf_conn and passes it to nf_l4proto_log_invalid().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently pass down the l4 protocol to the conntrack ->packet()
function, but the only user of this is the debug info decision.
Same information can be derived from struct nf_conn.
As a first step, add and use a new log function for this, similar to
nf_ct_helper_log().
Add __cold annotation -- invalid packets should be infrequent so
gcc can consider all call paths that lead to such a function as
unlikely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already allow to enable TFO without a cookie by using the
fastopen-sysctl and setting it to TFO_SERVER_COOKIE_NOT_REQD (or
TFO_CLIENT_NO_COOKIE).
This is safe to do in certain environments where we know that there
isn't a malicous host (aka., data-centers) or when the
application-protocol already provides an authentication mechanism in the
first flight of data.
A server however might be providing multiple services or talking to both
sides (public Internet and data-center). So, this server would want to
enable cookie-less TFO for certain services and/or for connections that
go to the data-center.
This patch exposes a socket-option and a per-route attribute to enable such
fine-grained configurations.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark hlist node in sk rcu iterator as protected by the rcu.
hlist_next_rcu accomplishes this and silences the warnings
sparse throws.
Found with make C=1 net/ipv4/udp.o on linux-next tag
next-20171009.
Signed-off-by: Tim Hansen <devtimhansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring IPv6 in par with IPv4 :
- Use net_hash_mix() to spread addresses a bit more.
- Use 256 slots hash table instead of 16
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
These helpers are no longer in use by drivers, so remove them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the tc_setup_cb_call entrypoint function originally used only for
action egress devices callbacks to call per-block callbacks as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure that allows drivers to register callbacks that
are called whenever tc would offload inserted rule for a specific block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use previously introduced extended variants of block get and put
functions. This allows to specify a binder types specific to clsact
ingress/egress which is useful for drivers to distinguish who actually
got the block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new type of ndo_setup_tc message to propage binding/unbinding
of a block to driver. Call this ndo whenever qdisc gets/puts a block.
Alongside with this, there's need to propagate binder type from qdisc
code down to the notifier. So introduce extended variants of
block_get/put in order to pass this info.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New socket option TCP_FASTOPEN_KEY to allow different keys per
listener. The listener by default uses the global key until the
socket option is set. The key is a 16 bytes long binary data. This
option has no effect on regular non-listener TCP sockets.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to in_validator_info and in6_validator_info. Update the one
user of each, ipvlan, to return an error message for failures.
Only manual configuration of an address is plumbed in the IPv6 code path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=YkMB
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20171018' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Add bits for kernel services
Here are some patches that add a few things for kernel services to use:
(1) Allow service upgrade to be requested and allow the resultant actual
service ID to be obtained.
(2) Allow the RTT time of a call to be obtained.
(3) Allow a kernel service to find out if a call is still alive on a
server between transmitting a request and getting the reply.
(4) Allow data transmission to ignore signals if transmission progress is
being made in reasonable time. This is also usable by userspace by
passing MSG_WAITALL to sendmsg()[*].
[*] I'm not sure this is the right interface for this or whether a sockopt
should be used instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Florian Westphal <fw@strlen.de>
Cc: linux-wpan@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: coreteam@netfilter.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com> # for ieee802154
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: dccp@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: linux-decnet-user@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a couple of functions to allow cleaner handling of signals in a
kernel service. They are:
(1) rxrpc_kernel_get_rtt()
This allows the kernel service to find out the RTT time for a call, so
as to better judge how large a timeout to employ.
Note, though, that whilst this returns a value in nanoseconds, the
timeouts can only actually be in jiffies.
(2) rxrpc_kernel_check_life()
This returns a number that is updated when ACKs are received from the
peer (notably including PING RESPONSE ACKs which we can elicit by
sending PING ACKs to see if the call still exists on the server).
The caller should compare the numbers of two calls to see if the call
is still alive.
These can be used to provide an extending timeout rather than returning
immediately in the case that a signal occurs that would otherwise abort an
RPC operation. The timeout would be extended if the server is still
responsive and the call is still apparently alive on the server.
For most operations this isn't that necessary - but for FS.StoreData it is:
OpenAFS writes the data to storage as it comes in without making a backup,
so if we immediately abort it when partially complete on a CTRL+C, say, we
have no idea of the state of the file after the abort.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide support for a kernel service to make use of the service upgrade
facility. This involves:
(1) Pass an upgrade request flag to rxrpc_kernel_begin_call().
(2) Make rxrpc_kernel_recv_data() return the call's current service ID so
that the caller can detect service upgrade and see what the service
was upgraded to.
Signed-off-by: David Howells <dhowells@redhat.com>
The fq structure would fail to properly enforce the memory limit in the case
where the packet being enqueued was bigger than the packet being removed to
bring the memory usage down. So keep dropping packets until the memory usage is
back below the limit. Also, fix the statistics for memory limit violations.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to not dirty the cacheline too often, we try to only update
dst->__use and dst->lastusetime at most once per jiffy.
As dst->lastusetime is only used by ipv6 garbage collector, it should
be good enough time resolution.
And __use is only used in ipv6_route_seq_show() to show how many times a
dst has been used. And as __use is not atomic_t right now, it does not
show the precise number of usage times anyway. So we think it should be
OK to only update it at most once per jiffy.
According to my latest syn flood test on a machine with intel Xeon 6th
gen processor and 2 10G mlx nics bonded together, each with 8 rx queues
on 2 NUMA nodes:
With this patch, the packet process rate increases from ~3.49Mpps to
~3.75Mpps with a 7% increase rate.
Note: dst_use() is being renamed to dst_hold_and_use() to better specify
the purpose of the function.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@googl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf_block_q helper to get q pointer to be used for direct call of
sch_tree_lock/unlock instead of tcf_tree_lock/unlock.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the block->q is set, it can be used instead of tp->q as it
contains the same value. When it is not set, which can't happen now but
it might happen with the follow-up shared blocks introduction, the class
is not set in the result. That would lead to a class lookup instead
of direct class pointer use for classful qdiscs. However, it is not
planned to support classful qdisqs sharing filter blocks, so that may
never happen.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These helpers allows to get a q and netdev pointers
for given block easily.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store net pointer in the block structure. Along the way, introduce
qdisc_net helper which allows to easily obtain net pointer for
qdisc instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for removal of tp->q and store Qdisc pointer in the block
structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-13
This series contains updates to mqprio and i40e.
Amritha introduces a new hardware offload mode in tc/mqprio where the TCs,
the queue configurations and bandwidth rate limits are offloaded to the
hardware. The existing mqprio framework is extended to configure the queue
counts and layout and also added support for rate limiting. This is
achieved through new netlink attributes for the 'mode' option which takes
values such as 'dcb' (default) and 'channel' and a 'shaper' option for
QoS attributes such as bandwidth rate limits in hw mode 1. Legacy devices
can fall back to the existing setup supporting hw mode 1 without these
additional options where only the TCs are offloaded and then the 'mode'
and 'shaper' options defaults to DCB support. The i40e driver enables the
new mqprio hardware offload mechanism factoring the TCs, queue
configuration and bandwidth rates by creating HW channel VSIs.
In this new mode, the priority to traffic class mapping and the user
specified queue ranges are used to configure the traffic class when the
'mode' option is set to 'channel'. This is achieved by creating HW
channels(VSI). A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC (TC0)
which is for the main VSI. TC0 for the main VSI is also reconfigured as
per user provided queue parameters. Finally, bandwidth rate limits are set
on these traffic classes through the shaper attribute by sending these
rates in addition to the number of TCs and the queue configurations.
Colin Ian King makes an array of constant values "constant".
Alan fixes and issue where on some firmware versions, we were failing to
actually fill out the phy_types which caused ethtool to not report any
link types. Also hardened against a potentially malicious VF by not
letting the VF to reset itself after requesting to change the number of
queues (via ethtool), let the PF reset the VF to institute the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload types currently supported in mqprio are 0 (no offload) and
1 (offload only TCs) by setting these values for the 'hw' option. If
offloads are supported by setting the 'hw' option to 1, the default
offload mode is 'dcb' where only the TC values are offloaded to the
device. This patch introduces a new hardware offload mode called
'channel' with 'hw' set to 1 in mqprio which makes full use of the
mqprio options, the TCs, the queue configurations and the QoS parameters
for the TCs. This is achieved through a new netlink attribute for the
'mode' option which takes values such as 'dcb' (default) and 'channel'.
The 'channel' mode also supports QoS attributes for traffic class such as
minimum and maximum values for bandwidth rate limits.
This patch enables configuring additional HW shaper attributes associated
with a traffic class. Currently the shaper for bandwidth rate limiting is
supported which takes options such as minimum and maximum bandwidth rates
and are offloaded to the hardware in the 'channel' mode. The min and max
limits for bandwidth rates are provided by the user along with the TCs
and the queue configurations when creating the mqprio qdisc. The interface
can be extended to support new HW shapers in future through the 'shaper'
attribute.
Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading
mqprio queue options and use this to be shared between the kernel and
device driver. This contains a copy of the existing data structure
for mqprio queue options. This new data structure can be extended when
adding new attributes for traffic class such as mode, shaper, shaper
parameters (bandwidth rate limits). The existing data structure for mqprio
queue options will be shared between the kernel and userspace.
Example:
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the parameter updating via RCU and not protected by a
spinlock anymore. This reduce the time that the spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make style of module alias name consistent with other subsystems in kernel,
for example net devices.
Fixes: 084e2f6566 ("Support to encoding decoding skb mark on IFE action")
Fixes: 200e10f469 ("Support to encoding decoding skb prio on IFE action")
Fixes: 408fbc22ef ("net sched ife action: Introduce skb tcindex metadata encap decap")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove three inline helpers that are no longer needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper and the struct field ares no longer used by any code,
so remove them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of cls_flower->egress_dev is mlx5. So do the conversion
there alongside with the code originating the call in cls_flower
function fl_hw_replace_filter to the newly introduced egress device
callback infrastucture.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure that allows drivers to register callbacks that
are called whenever tc would offload inserted rule and specified device
acts as tc action egress device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return dev directly, NULL if not possible. That is enough.
Makes no sense to pass struct net * to get_dev op, as there is only one
net possible, the one the action was created in. So just store it in
mirred priv and use directly.
Rename the mirred op callback function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yury reported crash with this signature :
[ 554.034021] [<ffff80003ccd5a58>] 0xffff80003ccd5a58
[ 554.034156] [<ffff00000888fd34>] skb_release_all+0x14/0x30
[ 554.034288] [<ffff00000888fd64>] __kfree_skb+0x14/0x28
[ 554.034409] [<ffff0000088ece6c>] tcp_sendmsg_locked+0x4dc/0xcc8
[ 554.034541] [<ffff0000088ed68c>] tcp_sendmsg+0x34/0x58
[ 554.034659] [<ffff000008919fd4>] inet_sendmsg+0x2c/0xf8
[ 554.034783] [<ffff0000088842e8>] sock_sendmsg+0x18/0x30
[ 554.034928] [<ffff0000088861fc>] SyS_sendto+0x84/0xf8
Problem is that skb->destructor contains garbage, and this is
because I accidentally removed tcp_skb_tsorted_anchor_cleanup()
from tcp_unlink_write_queue()
This would trigger with a write(fd, <invalid_memory>, len) attempt,
and we will add to packetdrill this capability to avoid future
regressions.
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Reported-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* port authorized event for 4-way-HS offload (Avi)
* enable MFP optional for such devices (Emmanuel)
* Kees's timer setup patch for mac80211 mesh
(the part that isn't trivially scripted)
* improve VLAN vs. TXQ handling (myself)
* load regulatory database as firmware file (myself)
* with various other small improvements and cleanups
I merged net-next once in the meantime to allow Kees's
timer setup patch to go in.
-----BEGIN PGP SIGNATURE-----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=gW8q
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Work continues in various areas:
* port authorized event for 4-way-HS offload (Avi)
* enable MFP optional for such devices (Emmanuel)
* Kees's timer setup patch for mac80211 mesh
(the part that isn't trivially scripted)
* improve VLAN vs. TXQ handling (myself)
* load regulatory database as firmware file (myself)
* with various other small improvements and cleanups
I merged net-next once in the meantime to allow Kees's
timer setup patch to go in.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to the FQ API a way to filter a given tin, in order to
remove frames that fulfil certain criteria according to a
filter function.
This will be used by mac80211 to remove frames belonging to
an AP VLAN interface that's being removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bpf_skb_set_tunnel_*() functions require allocation of per-cpu
metadata_dst. The allocation happens upon verification of the
first program using those helpers. In preparation for removing
the verifier lock, use cmpxchg() to make sure we only allocate
the metadata_dsts once.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phonet_protocol structs don't need to be written by anyone and
so can be marked as const.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, most of the rt6_stats are not hooked up correctly. As the
last part of this patch series, hook up all existing rt6_stats and add
one new stat fib_rt_uncache to indicate the number of routes in the
uncached list.
For details of the stats, please refer to the comments added in
include/net/ip6_fib.h.
Note: fib_rt_alloc and fib_rt_uncache are not guaranteed to be modified
under a lock. So atomic_t is used for them.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the preparation work before, we are now ready to replace rwlock
with rcu and spinlock in fib6_table.
That means now all fib6_node in fib6_table are protected by rcu. And
when freeing fib6_node, call_rcu() is used to wait for the rcu grace
period before releasing the memory.
When accessing fib6_node, corresponding rcu APIs need to be used.
And all previous sessions protected by the write lock will now be
protected by the spin lock per table.
All previous sessions protected by read lock will now be protected by
rcu_read_lock().
A couple of things to note here:
1. As part of the work of replacing rwlock with rcu, the linked list of
fn->leaf now has to be rcu protected as well. So both fn->leaf and
rt->dst.rt6_next are now __rcu tagged and corresponding rcu APIs are
used when manipulating them.
2. For fn->rr_ptr, first of all, it also needs to be rcu protected now
and is tagged with __rcu and rcu APIs are used in corresponding places.
Secondly, fn->rr_ptr is changed in rt6_select() which is a reader
thread. This makes the issue a bit complicated. We think a valid
solution for it is to let rt6_select() grab the tb6_lock if it decides
to change it. As it is not in the normal operation and only happens when
there is no valid neighbor cache for the route, we think the performance
impact should be low.
3. fib6_walk_continue() has to be called with tb6_lock held even in the
route dumping related functions, e.g. inet6_dump_fib(),
fib6_tables_dump() and ipv6_route_seq_ops. It is because
fib6_walk_continue() makes modifications to the walker structure, and so
are fib6_repair_tree() and fib6_del_route(). In order to do proper
syncing between them, we need to let fib6_walk_continue() hold the lock.
We may be able to do further improvement on the way we do the tree walk
to get rid of the need for holding the spin lock. But not for now.
4. When fib6_del_route() removes a route from the tree, we no longer
mark rt->dst.rt6_next to NULL to make simultaneous reader be able to
further traverse the list with rcu. However, rt->dst.rt6_next is only
valid within this same rcu period. No one should access it later.
5. All the operation of atomic_inc(rt->rt6i_ref) is changed to be
performed before we publish this route (either by linking it to fn->leaf
or insert it in the list pointed by fn->leaf) just to be safe because as
soon as we publish the route, some read thread will be able to access it.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_add() logic currently calls fib6_add_1() to figure out what node
should be used for the newly added route and then call
fib6_add_rt2node() to insert the route to the node.
And during the call of fib6_add_1(), fn_sernum is updated for all nodes
that share the same prefix as the new route.
This does not have issue in the current code because reader thread will
not be able to access the tree while writer thread is inserting new
route to it. However, it is not the case once we transition to use RCU.
Reader thread could potentially see the new fn_sernum before the new
route is inserted. As a result, reader thread's route lookup will return
a stale route with the new fn_sernum.
In order to solve this issue, we remove all the update of fn_sernum in
fib6_add_1(), and instead, introduce a new function that updates fn_sernum
for all related nodes and call this functions once the route is
successfully inserted to the tree.
Also, smp_wmb() is used after a route is successfully inserted into the
fib tree and right before the updated of fn->sernum. And smp_rmb() is
used right after fn->sernum is accessed in rt6_get_cookie_safe(). This
is to guarantee that when the reader thread sees the new fn->sernum, the
new route is already inserted in the tree in memory.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes use of the exception hash table implementation to
store dst caches created by pmtu discovery and ip redirect into the hash
table under the rt_info and no longer inserts these routes into fib6
tree.
This makes the fib6 tree only contain static configured routes and could
now be protected by rcu instead of a rw lock.
With this change, in the route lookup related functions, after finding
the rt6_info with the longest prefix, we also need to search for the
exception table before doing backtracking.
In the route delete function, if the route being deleted is not a dst
cache, deletion of this route also need to flush the whole hash table
under it. If it is a dst cache, then only delete the cached dst in the
hash table.
Note: for fib6_walk_continue() function, w->root now is always pointing
to a root node considering that fib6_prune_clones() is removed from the
code. So we add a WARN_ON() msg to make sure w->root always points to a
root node and also removed the update of w->root in fib6_repair_tree().
This is a prerequisite for later patch because we don't need to make
w->root as rcu protected when replacing rwlock with RCU.
Also, we remove all prune related variables as it is no longer used.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_locate() is used to find the fib6_node according to the passed in
prefix address key. It currently tries to find the fib6_node with the
exact match of the passed in key. However, when we move cached routes
into the exception table, fib6_locate() will fail to find the fib6_node
for it as the cached routes will be stored in the exception table under
the fib6_node with the longest prefix match of the cache's dst addr key.
This commit adds a new parameter to let the caller specify if it needs
exact match or longest prefix match.
Right now, all callers still does exact match when calling
fib6_locate(). It will be changed in later commit where exception table
is hooked up to store cached routes.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all dst cache entries are stored in the exception table under the
main route, we have to go through them during fib6_age() when doing
garbage collecting.
Introduce a new function rt6_age_exception() which goes through all dst
entries in the exception table and remove those entries that are expired.
This function is called in fib6_age() so that all dst caches are also
garbage collected.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hash table into struct rt6_info in order to store dst caches
created by pmtu discovery and ip redirect in ipv6 routing code.
APIs to add dst cache, delete dst cache, find dst cache and update
dst cache in the hash table are implemented and will be used in later
commits.
This is a preparation work to move all cache routes into the exception
table instead of getting inserted into the fib6 tree.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function takes a route as input and tries to update the sernum in
the fib6_node this route is associated with. It will be used in later
commit when adding a cached route into the exception table under that
route.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a linear list to store all skbs in write queue has been okay
for quite a while : O(N) is not too bad when N < 500.
Things get messy when N is the order of 100,000 : Modern TCP stacks
want 10Gbit+ of throughput even with 200 ms RTT flows.
40 ns per cache line miss means a full scan can use 4 ms,
blowing away CPU caches.
SACK processing often can use various hints to avoid parsing
whole retransmit queue. But with high packet losses and/or high
reordering, hints no longer work.
Sender has to process thousands of unfriendly SACK, accumulating
a huge socket backlog, burning a cpu and massively dropping packets.
Using an rb-tree for retransmit queue has been avoided for years
because it added complexity and overhead, but now is the time
to be more resistant and say no to quadratic behavior.
1) RTX queue is no longer part of the write queue : already sent skbs
are stored in one rb-tree.
2) Since reaching the head of write queue no longer needs
sk->sk_send_head, we added an union of sk_send_head and tcp_rtx_queue
Tested:
On receiver :
netem on ingress : delay 150ms 200us loss 1
GRO disabled to force stress and SACK storms.
for f in `seq 1 10`
do
./netperf -H lpaa6 -l30 -- -K bbr -o THROUGHPUT|tail -1
done | awk '{print $0} {sum += $0} END {printf "%7u\n",sum}'
Before patch :
323.87
351.48
339.59
338.62
306.72
204.07
304.93
291.88
202.47
176.88
2840
After patch:
1700.83
2207.98
2070.17
1544.26
2114.76
2124.89
1693.14
1080.91
2216.82
1299.94
18053
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the upcoming rtx rbtree will add some extra code,
it is time to not inline this fat function anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit cc71b7b071 ("net/ipv6: remove unused err variable on
icmpv6_push_pending_frames") exposed icmpv6_push_pending_frames
return value not being used.
Remove now unnecessary int err declarations and uses.
Miscellanea:
o Remove unnecessary goto and out: labels
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging this brings in the timer_setup() change, which allows
me to apply Kees's mac80211 changes for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a new queue (list) that tracks the sent but not yet
acked or SACKed skbs for a TCP connection. The list is chronologically
ordered by skb->skb_mstamp (the head is the oldest sent skb).
This list will be used to optimize TCP Rack recovery, which checks
an skb's timestamp to judge if it has been lost and needs to be
retransmitted. Since TCP write queue is ordered by sequence instead
of sent time, RACK has to scan over the write queue to catch all
eligible packets to detect lost retransmission, and iterates through
SACKed skbs repeatedly.
Special cares for rare events:
1. TCP repair fakes skb transmission so the send queue needs adjusted
2. SACK reneging would require re-inserting SACKed skbs into the
send queue. For now I believe it's not worth the complexity to
make RACK work perfectly on SACK reneging, so we do nothing here.
3. Fast Open: currently for non-TFO, send-queue correctly queues
the pure SYN packet. For TFO which queues a pure SYN and
then a data packet, send-queue only queues the data packet but
not the pure SYN due to the structure of TFO code. This is okay
because the SYN receiver would never respond with a SACK on a
missing SYN (i.e. SYN is never fast-retransmitted by SACK/RACK).
In order to not grow sk_buff, we use an union for the new list and
_skb_refdst/destructor fields. This is a bit complicated because
we need to make sure _skb_refdst and destructor are properly zeroed
before skb is cloned/copied at transmit, and before being freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in the TCP code, the initialization sequence for cached
metrics, congestion control, BPF, etc, after successful connection
is very inconsistent. This introduces inconsistent bevhavior and is
prone to bugs. The current call sequence is as follows:
(1) for active case (tcp_finish_connect() case):
tcp_mtup_init(sk);
icsk->icsk_af_ops->rebuild_header(sk);
tcp_init_metrics(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_ACTIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_init_buffer_space(sk);
(2) for passive case (tcp_rcv_state_process() TCP_SYN_RECV case):
icsk->icsk_af_ops->rebuild_header(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_mtup_init(sk);
tcp_init_buffer_space(sk);
tcp_init_metrics(sk);
(3) for TFO passive case (tcp_fastopen_create_child()):
inet_csk(child)->icsk_af_ops->rebuild_header(child);
tcp_init_congestion_control(child);
tcp_mtup_init(child);
tcp_init_metrics(child);
tcp_call_bpf(child, BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB);
tcp_init_buffer_space(child);
This commit uniforms the above functions to have the following sequence:
tcp_mtup_init(sk);
icsk->icsk_af_ops->rebuild_header(sk);
tcp_init_metrics(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_ACTIVE/PASSIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_init_buffer_space(sk);
This sequence is the same as the (1) active case. We pick this sequence
because this order correctly allows BPF to override the settings
including congestion control module and initial cwnd, etc from
the route, and then allows the CC module to see those settings.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two state fields: socket->state and sock->sk_state. The
socket->state field uses SS_UNCONNECTED, SS_CONNECTED, etc while the
sock->sk_state typically uses values that match TCP state constants
(TCP_CLOSE, TCP_ESTABLISHED). AF_VSOCK does not follow this convention
and instead uses SS_* constants for both fields.
The sk_state field will be exposed to userspace through the vsock_diag
interface for ss(8), netstat(8), and other programs.
This patch switches sk_state to TCP state constants so that the meaning
of this field is consistent with other address families. Not just
AF_INET and AF_INET6 use the TCP constants, AF_UNIX and others do too.
The following mapping was used to convert the code:
SS_FREE -> TCP_CLOSE
SS_UNCONNECTED -> TCP_CLOSE
SS_CONNECTING -> TCP_SYN_SENT
SS_CONNECTED -> TCP_ESTABLISHED
SS_DISCONNECTING -> TCP_CLOSING
VSOCK_SS_LISTEN -> TCP_LISTEN
In __vsock_create() the sk_state initialization was dropped because
sock_init_data() already initializes sk_state to TCP_CLOSE.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsock_diag.ko module will need to check socket table membership.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket table symbols need to be exported from vsock.ko so that the
vsock_diag.ko module will be able to traverse sockets.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
no users in the tree.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces RFC Draft ndata section 3.2 Priority Based
Scheduler (SCTP_SS_RR).
Works by maintaining a list of enqueued streams and tracking the last
one used to send data. When the datamsg is done, it switches to the next
stream.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-sctp-ndata-13
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces RFC Draft ndata section 3.4 Priority Based
Scheduler (SCTP_SS_PRIO).
It works by having a struct sctp_stream_priority for each priority
configured. This struct is then enlisted on a queue ordered per priority
if, and only if, there is a stream with data queued, so that dequeueing
is very straightforward: either finish current datamsg or simply dequeue
from the highest priority queued, which is the next stream pointed, and
that's it.
If there are multiple streams assigned with the same priority and with
data queued, it will do round robin amongst them while respecting
datamsgs boundaries (when not using idata chunks), to be reasonably
fair.
We intentionally don't maintain a list of priorities nor a list of all
streams with the same priority to save memory. The first would mean at
least 2 other pointers per priority (which, for 1000 priorities, that
can mean 16kB) and the second would also mean 2 other pointers but per
stream. As SCTP supports up to 65535 streams on a given asoc, that's
1MB. This impacts when giving a priority to some stream, as we have to
find out if the new priority is already being used and if we can free
the old one, and also when tearing down.
The new fields in struct sctp_stream_out_ext and sctp_stream are added
under a union because that memory is to be shared with other schedulers.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-sctp-ndata-13
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the hooks necessary to do stream scheduling, as
per RFC Draft ndata. It also introduces the first scheduler, which is
what we do today but now factored out: first come first served (FCFS).
With stream scheduling now we have to track which chunk was enqueued on
which stream and be able to select another other than the in front of
the main outqueue. So we introduce a list on sctp_stream_out_ext
structure for this purpose.
We reuse sctp_chunk->transmitted_list space for the list above, as the
chunk cannot belong to the two lists at the same time. By using the
union in there, we can have distinct names for these moments.
sctp_sched_ops are the operations expected to be implemented by each
scheduler. The dequeueing is a bit particular to this implementation but
it is to match how we dequeue packets today. We first dequeue and then
check if it fits the packet and if not, we requeue it at head. Thus why
we don't have a peek operation but have dequeue_done instead, which is
called once the chunk can be safely considered as transmitted.
The check removed from sctp_outq_flush is now performed by
sctp_stream_outq_migrate, which is only called during assoc setup.
(sctp_sendmsg() also checks for it)
The only operation that is foreseen but not yet added here is a way to
signalize that a new packet is starting or that the packet is done, for
round robin scheduler per packet, but is intentionally left to the
patch that actually implements it.
Support for I-DATA chunks, also described in this RFC, with user message
interleaving is straightforward as it just requires the schedulers to
probe for the feature and ignore datamsg boundaries when dequeueing.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-sctp-ndata-13
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to fetch the stream number from a given chunk.
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the stream schedulers, sctp_stream_out will become too big to be
allocated by kmalloc and as we need to allocate with BH disabled, we
cannot use __vmalloc in sctp_stream_init().
This patch moves out the stats from sctp_stream_out to
sctp_stream_out_ext, which will be allocated only when the application
tries to sendmsg something on it.
Just the introduction of sctp_stream_out_ext would already fix the issue
described above by splitting the allocation in two. Moving the stats
to it also reduces the pressure on the allocator as we will ask for less
memory atomically when creating the socket and we will use GFP_KERNEL
later.
Then, for stream schedulers, we will just use sctp_stream_out_ext.
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb parameter of skb_metadata_dst() and skb_tunnel_info()
const as they are not modified. This is in preparation for using
them in call-sites where skb is const.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an event that indicates that a connection is authorized
(i.e. the 4 way handshake was performed by the driver). This event
should be sent by the driver after sending a connect/roamed event.
This is useful for networks that require 802.1X authentication.
In cases that the driver supports 4 way handshake offload, but the
802.1X authentication is managed by user space, the driver needs to
inform user space right after the 802.11 association was completed
so user space can initialize its 802.1X state machine etc.
However, it is also possible that the AP will choose to skip the
802.1X authentication (e.g. when PMKSA caching is used) and proceed
with the 4 way handshake immediately. In this case the driver needs
to inform user space that 802.1X authentication is no longer required
(e.g. to prevent user space from disconnecting since it did not get
any EAPOLs from the AP).
This is also useful for roaming, in which case it is possible that
the driver used the Fast Transition protocol so 802.1X is not
required.
Since there will now be a dedicated notification indicating that the
connection is authorized, the authorized flag can be removed from the
roamed event. Drivers can send the new port authorized event right
after sending the roamed event to indicate the new AP is already
authorized. This therefore reserves the old PORT_AUTHORIZED attribute.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is unused, and furthermore it is buggy since it suffers
from the same issue that requires IP6_ECN_set_ce() to take a pointer
to the skb so that it may (in case of CHECKSUM_COMPLETE) update skb->csum
Instead of fixing it, let's just outright remove it.
Tested: builds, and 'git grep IP6_ECN_clear' comes up empty
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different time period in
second to disable Fastopen on active TCP sockets.
Tested:
Simulate following similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
And then print netstat of TCPFastOpenBlackhole, the counter increased as
expected when the firewall blackhole issue is detected and active TFO is
disabled.
# cat /proc/net/netstat | awk '{print $91}'
TCPFastOpenBlackhole
1
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different tcp_fastopen_key
independently of the host.
David Miller pointed out there is a leak without releasing the context
of tcp_fastopen_key during netns teardown. So add the release action in
exit_batch path.
Tested:
1. Container namespace:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
2817fff2-f803cf97-eadfd1f3-78c0992b
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: 1e5dd82a8c492ca9
2. Host:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
107d7c5f-68eb2ac7-02fb06e6-ed341702
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: e213c02bf0afbc8a
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'publish' logic is not necessary after commit dfea2aa654 ("tcp:
Do not call tcp_fastopen_reset_cipher from interrupt context"), because
in tcp_fastopen_cookie_gen，it wouldn't call tcp_fastopen_init_key_once.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require enable TCP Fast Open
feature independently of the host.
This patch series continues making more of the TCP Fast Open related
sysctl knobs be per net-namespace.
Reported-by: Luca BRUNO <lucab@debian.org>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_ptr is a dsa_port instance, there is no need to keep
the tag operations in the dsa_switch_tree structure. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make DSA master devices point to their corresponding
CPU port instead of the whole tree, add copies of dst and rcv in the
dsa_port structure so that we keep fast access in the receive hot path.
Also keep the copies at the beginning of the dsa_port structure in order
to ensure they are available in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging protocol operations are specific to each CPU port,
thus the dsa_device_ops pointer belongs to the dsa_port structure.
>From now on assign a slave's xmit copy from its CPU port tagging
operations. This will ease the future support for multiple CPU ports.
Also keep the tag_ops at the beginning of the dsa_port structure so that
we ensure copies for hot path are in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP early demux can leverate the rx dst cache even for
multicast unconnected sockets.
In such scenario the ipv4 source address is validated only on
the first packet in the given flow. After that, when we fetch
the dst entry from the socket rx cache, we stop enforcing
the rp_filter and we even start accepting any kind of martian
addresses.
Disabling the dst cache for unconnected multicast socket will
cause large performace regression, nearly reducing by half the
max ingress tput.
Instead we factor out a route helper to completely validate an
skb source address for multicast packets and we call it from
the UDP early demux for mcast packets landing on unconnected
sockets, after successful fetching the related cached dst entry.
This still gives a measurable, but limited performance
regression:
rp_filter = 0 rp_filter = 1
edmux disabled: 1182 Kpps 1127 Kpps
edmux before: 2238 Kpps 2238 Kpps
edmux after: 2037 Kpps 2019 Kpps
The above figures are on top of current net tree.
Applying the net-next commit 6e617de84e ("net: avoid a full
fib lookup when rp_filter is disabled.") the delta with
rp_filter == 0 will decrease even more.
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently no error is emitted, but this infrastructure will
used by the next patch to allow source address validation
for mcast sockets.
Since early demux can do a route lookup and an ipv4 route
lookup can return an error code this is consistent with the
current ipv4 route infrastructure.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_weight in fib_info is set but not used. Remove it and the
helpers for setting it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ipmr module register as a FIB notifier. To do that, implement both
the ipmr_seq_read and ipmr_dump ops.
The ipmr_seq_read op returns a sequence counter that is incremented on
every notification related operation done by the ipmr. To implement that,
add a sequence counter in the netns_ipv4 struct and increment it whenever a
new MFC route or VIF are added or deleted. The sequence operations are
protected by the RTNL lock.
The ipmr_dump iterates the list of MFC routes and the list of VIF entries
and sends notifications about them. The entries dump is done under RCU
where the VIF dump uses the mrt_lock too, as the vif->dev field can change
under RCU.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for an interface to forward packets according to the kernel
multicast routing table, it must be configured with a VIF index according
to the mroute user API. The VIF index is then used to refer to that
interface in the mroute user API, for example, to set the iif and oifs of
an MFC entry.
In order to allow drivers to be aware and offload multicast routes, they
have to be aware of the VIF add and delete notifications.
Due to the fact that a specific VIF can be deleted and re-added pointing to
another netdevice, and the MFC routes that point to it will forward the
matching packets to the new netdevice, a driver willing to offload MFC
cache entries must be aware of the VIF add and delete events in addition to
MFC routes notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper called is_tcf_gact_pass which could be used to
tell if the action is gact pass or not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key length can't be negative.
Leave comparisons against nla_len() signed just in case truncated attribute
can sneak in there.
Space savings:
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-7 (-7)
function old new delta
pneigh_delete 273 272 -1
mlx5e_rep_netevent_event 1415 1414 -1
mlx5e_create_encap_header_ipv6 1194 1193 -1
mlx5e_create_encap_header_ipv4 1071 1070 -1
cxgb4_l2t_get 1104 1103 -1
__pneigh_lookup 69 68 -1
__neigh_create 2452 2451 -1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_KASAN is enabled, the "--param asan-stack=1" causes rather large
stack frames in some functions. This goes unnoticed normally because
CONFIG_FRAME_WARN is disabled with CONFIG_KASAN by default as of commit
3f181b4d86 ("lib/Kconfig.debug: disable -Wframe-larger-than warnings with
KASAN=y").
The kernelci.org build bot however has the warning enabled and that led
me to investigate it a little further, as every build produces these warnings:
net/wireless/nl80211.c:4389:1: warning: the frame size of 2240 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1895:1: warning: the frame size of 3776 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1410:1: warning: the frame size of 2208 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/bridge/br_netlink.c:1282:1: warning: the frame size of 2544 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Most of this problem is now solved in gcc-8, which can consolidate
the stack slots for the inline function arguments. On older compilers
we can add a workaround by declaring a local variable in each function
to pass the inline function argument.
Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replay detection bitmaps can't have negative length.
Comparisons with nla_len() are left signed just in case negative value
can sneak in there.
Propagate unsignedness for code size savings:
add/remove: 0/0 grow/shrink: 0/5 up/down: 0/-38 (-38)
function old new delta
xfrm_state_construct 1802 1800 -2
xfrm_update_ae_params 295 289 -6
xfrm_state_migrate 1345 1339 -6
xfrm_replay_notify_esn 349 337 -12
xfrm_replay_notify_bmp 345 333 -12
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Key lengths can't be negative.
Comparison with nla_len() is left signed just in case negative value
can sneak in there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In linux-4.13, Wei worked hard to convert dst to a traditional
refcounted model, removing GC.
We now want to make sure a dst refcount can not transition from 0 back
to 1.
The problem here is that input path attached a not refcounted dst to an
skb. Then later, because packet is forwarded and hits skb_dst_force()
before exiting RCU section, we might try to take a refcount on one dst
that is about to be freed, if another cpu saw 1 -> 0 transition in
dst_release() and queued the dst for freeing after one RCU grace period.
Lets unify skb_dst_force() and skb_dst_force_safe(), since we should
always perform the complete check against dst refcount, and not assume
it is not zero.
Bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=197005
[ 989.919496] skb_dst_force+0x32/0x34
[ 989.919498] __dev_queue_xmit+0x1ad/0x482
[ 989.919501] ? eth_header+0x28/0xc6
[ 989.919502] dev_queue_xmit+0xb/0xd
[ 989.919504] neigh_connected_output+0x9b/0xb4
[ 989.919507] ip_finish_output2+0x234/0x294
[ 989.919509] ? ipt_do_table+0x369/0x388
[ 989.919510] ip_finish_output+0x12c/0x13f
[ 989.919512] ip_output+0x53/0x87
[ 989.919513] ip_forward_finish+0x53/0x5a
[ 989.919515] ip_forward+0x2cb/0x3e6
[ 989.919516] ? pskb_trim_rcsum.part.9+0x4b/0x4b
[ 989.919518] ip_rcv_finish+0x2e2/0x321
[ 989.919519] ip_rcv+0x26f/0x2eb
[ 989.919522] ? vlan_do_receive+0x4f/0x289
[ 989.919523] __netif_receive_skb_core+0x467/0x50b
[ 989.919526] ? tcp_gro_receive+0x239/0x239
[ 989.919529] ? inet_gro_receive+0x226/0x238
[ 989.919530] __netif_receive_skb+0x4d/0x5f
[ 989.919532] netif_receive_skb_internal+0x5c/0xaf
[ 989.919533] napi_gro_receive+0x45/0x81
[ 989.919536] ixgbe_poll+0xc8a/0xf09
[ 989.919539] ? kmem_cache_free_bulk+0x1b6/0x1f7
[ 989.919540] net_rx_action+0xf4/0x266
[ 989.919543] __do_softirq+0xa8/0x19d
[ 989.919545] irq_exit+0x5d/0x6b
[ 989.919546] do_IRQ+0x9c/0xb5
[ 989.919548] common_interrupt+0x93/0x93
[ 989.919548] </IRQ>
Similarly dst_clone() can use dst_hold() helper to have additional
debugging, as a follow up to commit 44ebe79149 ("net: add debug
atomic_inc_not_zero() in dst_hold()")
In net-next we will convert dst atomic_t to refcount_t for peace of
mind.
Fixes: a4c2fd7f78 ("net: remove DST_NOCACHE flag")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Bisected-by: Paweł Staszewski <pstaszewski@itcare.pl>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> net/ipv4/fib_frontend.c: In function 'fib_validate_source':
> net/ipv4/fib_frontend.c:411:16: error: 'struct netns_ipv4' has no member named 'fib_has_custom_local_routes'
> if (net->ipv4.fib_has_custom_local_routes)
> ^
> net/ipv4/fib_frontend.c: In function 'inet_rtm_newroute':
> net/ipv4/fib_frontend.c:773:12: error: 'struct netns_ipv4' has no member named 'fib_has_custom_local_routes'
> net->ipv4.fib_has_custom_local_routes = true;
> ^
Fixes: 6e617de84e ("net: avoid a full fib lookup when rp_filter is disabled.")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1dced6a854 ("ipv4: Restore accept_local behaviour
in fib_validate_source()") a full fib lookup is needed even if
the rp_filter is disabled, if accept_local is false - which is
the default.
What we really need in the above scenario is just checking
that the source IP address is not local, and in most case we
can do that is a cheaper way looking up the ifaddr hash table.
This commit adds a helper for such lookup, and uses it to
validate the src address when rp_filter is disabled and no
'local' routes are created by the user space in the relevant
namespace.
A new ipv4 netns flag is added to account for such routes.
We need that to preserve the same behavior we had before this
patch.
It also drops the checks to bail early from __fib_validate_source,
added by the commit 1dced6a854 ("ipv4: Restore accept_local
behaviour in fib_validate_source()") they do not give any
measurable performance improvement: if we do the lookup with are
on a slower path.
This improves UDP performances for unconnected sockets
when rp_filter is disabled by 5% and also gives small but
measurable performance improvement for TCP flood scenarios.
v1 -> v2:
- use the ifaddr lookup helper in __ip_dev_find(), as suggested
by Eric
- fall-back to full lookup if custom local routes are present
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function hasn't been used since the removal of iwmc3200wifi
in 2012. It also appears to have a bug when qos=True, since then
it'll copy uninitialized stack memory to the SKB.
Just remove the function entirely.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add documentation to ieee80211_rx_ba_offl() function and, while at it,
rename the bit argument to tid, for consistency.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current ieee80211_ie_split() implementation doesn't
account for elements that are sub-elements of the
EXTENSION IE. To extend support to these IEs as well,
treat the WLAN_EID_EXTENSION ids in the %ids array
as indicating that the next id in the array is a
sub-element of the EXTENSION IE.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having a global list of labels do not scale to thousands of
netns in the cloud era. This causes quadratic behavior on
netns creation and deletion.
This is time having a per netns list of ~10 labels.
Tested:
$ time perf record (for f in `seq 1 3000` ; do ip netns add tast$f; done)
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 3.637 MB perf.data (~158898 samples) ]
real 0m20.837s # instead of 0m24.227s
user 0m0.328s
sys 0m20.338s # instead of 0m23.753s
16.17% ip [kernel.kallsyms] [k] netlink_broadcast_filtered
12.30% ip [kernel.kallsyms] [k] netlink_has_listeners
6.76% ip [kernel.kallsyms] [k] _raw_spin_lock_irqsave
5.78% ip [kernel.kallsyms] [k] memset_erms
5.77% ip [kernel.kallsyms] [k] kobject_uevent_env
5.18% ip [kernel.kallsyms] [k] refcount_sub_and_test
4.96% ip [kernel.kallsyms] [k] _raw_read_lock
3.82% ip [kernel.kallsyms] [k] refcount_inc_not_zero
3.33% ip [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
2.11% ip [kernel.kallsyms] [k] unmap_page_range
1.77% ip [kernel.kallsyms] [k] __wake_up
1.69% ip [kernel.kallsyms] [k] strlen
1.17% ip [kernel.kallsyms] [k] __wake_up_common
1.09% ip [kernel.kallsyms] [k] insert_header
1.04% ip [kernel.kallsyms] [k] page_remove_rmap
1.01% ip [kernel.kallsyms] [k] consume_skb
0.98% ip [kernel.kallsyms] [k] netlink_trim
0.51% ip [kernel.kallsyms] [k] kernfs_link_sibling
0.51% ip [kernel.kallsyms] [k] filemap_map_pages
0.46% ip [kernel.kallsyms] [k] memcpy_erms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen estimator has been rewritten in commit 1c0d32fde5
("net_sched: gen_estimator: complete rewrite of rate estimators"),
the caller no longer needs to wait for a grace period. So this
patch gets rid of it.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a copy of the master ethtool ops, storing the
original pointer in DSA and the new one in the master netdev itself is
enough.
In the meantime, set orig_ethtool_ops to NULL when restoring the master
ethtool ops and check the presence of the master original ethtool ops as
well as its needed functions before calling them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->rbnode shares space with skb->next, skb->prev and skb->tstamp
Current uses (TCP receive ofo queue and netem) need to save/restore
tstamp, while skb->dev is either NULL (TCP) or a constant for a given
queue (netem).
Since we plan using an RB tree for TCP retransmit queue to speedup SACK
processing with large BDP, this patch exchanges skb->dev and
skb->tstamp.
This saves some overhead in both TCP and netem.
v2: removes the swtstamp field from struct tcp_skb_cb
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove tcp_may_send_now and tcp_snd_test that are no longer used
Fixes: 840a3cbe89 ("tcp: remove forward retransmit feature")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global function ipv6_rcv_saddr_equal and static functions
ipv6_rcv_saddr_equal and ipv4_rcv_saddr_equal currently return int.
bool is slightly more descriptive for these functions so change
their return type from int to bool.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86fdb3448c ("sctp: ensure ep is not destroyed before doing the
dump") tried to fix an use-after-free issue by checking !sctp_sk(sk)->ep
with holding sock and sock lock.
But Paolo noticed that endpoint could be destroyed in sctp_rcv without
sock lock protection. It means the use-after-free issue still could be
triggered when sctp_rcv put and destroy ep after sctp_sock_dump checks
!ep, although it's pretty hard to reproduce.
I could reproduce it by mdelay in sctp_rcv while msleep in sctp_close
and sctp_sock_dump long time.
This patch is to add another param cb_done to sctp_for_each_transport
and dump ep->assocs with holding tsp after jumping out of transport's
traversal in it to avoid this issue.
It can also improve sctp diag dump to make it run faster, as no need
to save sk into cb->args[5] and keep calling sctp_for_each_transport
any more.
This patch is also to use int * instead of int for the pos argument
in sctp_for_each_transport, which could make postion increment only
in sctp_for_each_transport and no need to keep changing cb->args[2]
in sctp_sock_filter and sctp_sock_dump any more.
Fixes: 86fdb3448c ("sctp: ensure ep is not destroyed before doing the dump")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code causes a static checker warning because Smatch doesn't trust
anything that comes from skb->data. I've reviewed this code and I do
think skb->data can be controlled by the user here.
The sctp_event_subscribe struct has 13 __u8 fields and we want to see
if ours is non-zero. sn_type can be any value in the 0-USHRT_MAX range.
We're subtracting SCTP_SN_TYPE_BASE which is 1 << 15 so we could read
either before the start of the struct or after the end.
This is a very old bug and it's surprising that it would go undetected
for so long but my theory is that it just doesn't have a big impact so
it would be hard to notice.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen estimator has been rewritten in commit 1c0d32fde5
("net_sched: gen_estimator: complete rewrite of rate estimators"),
the caller is no longer needed to wait for a grace period.
So this patch gets rid of it.
This also completely closes a race condition between action free
path and filter chain add/remove path for the following patch.
Because otherwise the nested RCU callback can't be caught by
rcu_barrier().
Please see also the comments in code.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix SCTP connection setup when IPVS module is loaded and any scheduler
is registered, from Xin Long.
2) Don't create a SCTP connection from SCTP ABORT packets, also from
Xin Long.
3) WARN_ON() and drop packet, instead of BUG_ON() races when calling
nf_nat_setup_info(). This is specifically a longstanding problem
when br_netfilter with conntrack support is in place, patch from
Florian Westphal.
4) Avoid softlock splats via iptables-restore, also from Florian.
5) Revert NAT hashtable conversion to rhashtable, semantics of rhlist
are different from our simple NAT hashtable, this has been causing
problems in the recent Linux kernel releases. From Florian.
6) Add per-bucket spinlock for NAT hashtable, so at least we restore
one of the benefits we got from the previous rhashtable conversion.
7) Fix incorrect hashtable size in memory allocation in xt_hashlimit,
from Zhizhou Tian.
8) Fix build/link problems with hashlimit and 32-bit arches, to address
recent fallout from a new hashlimit mode, from Vishwanath Pai.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 870190a9ec.
It was not a good idea. The custom hash table was a much better
fit for this purpose.
A fast lookup is not essential, in fact for most cases there is no lookup
at all because original tuple is not taken and can be used as-is.
What needs to be fast is insertion and deletion.
rhlist removal however requires a rhlist walk.
We can have thousands of entries in such a list if source port/addresses
are reused for multiple flows, if this happens removal requests are so
expensive that deletions of a few thousand flows can take several
seconds(!).
The advantages that we got from rhashtable are:
1) table auto-sizing
2) multiple locks
1) would be nice to have, but it is not essential as we have at
most one lookup per new flow, so even a million flows in the bysource
table are not a problem compared to current deletion cost.
2) is easy to add to custom hash table.
I tried to add hlist_node to rhlist to speed up rhltable_remove but this
isn't doable without changing semantics. rhltable_remove_fast will
check that the to-be-deleted object is part of the table and that
requires a list walk that we want to avoid.
Furthermore, using hlist_node increases size of struct rhlist_head, which
in turn increases nf_conn size.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196821
Reported-by: Ivan Babrou <ibobrik@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
-----BEGIN PGP SIGNATURE-----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=QYS4
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Back from a long absence, so we have a number of things:
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.
Reported-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a new link error in allmodconfig kernels after ftgmac100
started using the ncsi helpers:
ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
Related to that, we get another error when CONFIG_NET_NCSI is disabled:
drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?
This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.
Fixes: 51564585d8 ("ftgmac100: Support NCSI VLAN filtering when available")
Fixes: 21acf63013 ("net/ncsi: Configure VLAN tag filter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TXQs, the AP_VLAN interfaces are resolved to their owner AP
interface when enqueuing the frame, which makes sense since the
frame really goes out on that as far as the driver is concerned.
However, this introduces a problem: frames to be encrypted with
a VLAN-specific GTK will now be encrypted with the AP GTK, since
the information about which virtual interface to use to select
the key is taken from the TXQ.
Fix this by preserving info->control.vif and using that in the
dequeue function. This now requires doing the driver-mapping
in the dequeue as well.
Since there's no way to filter the frames that are sitting on a
TXQ, drop all frames, which may affect other interfaces, when an
AP_VLAN is removed.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for next-net (part 2)
The following patchset contains Netfilter updates for net-next. This
patchset includes updates for nf_tables, removal of
CONFIG_NETFILTER_DEBUG and a new mode for xt_hashlimit. More
specifically, they:
1) Add new rate match mode for hashlimit, this introduces a new revision
for this match. The idea is to stop matching packets until ratelimit
criteria stands true. Patch from Vishwanath Pai.
2) Add ->select_ops indirection to nf_tables named objects, so we can
choose between different flavours of the same object type, patch from
Pablo M. Bermudo.
3) Shorter function names in nft_limit, basically:
s/nft_limit_pkt_bytes/nft_limit_bytes, also from Pablo M. Bermudo.
4) Add new stateful limit named object type, this allows us to create
limit policies that you can identify via name, also from Pablo.
5) Remove unused hooknum parameter in conntrack ->packet indirection.
From Florian Westphal.
6) Patches to remove CONFIG_NETFILTER_DEBUG and macros such as
IP_NF_ASSERT and IP_NF_ASSERT. From Varsha Rao.
7) Add nf_tables_updchain() helper function and use it from
nf_tables_newchain() to make it more maintainable. Similarly,
add nf_tables_addchain() and use it too.
8) Add new netlink NLM_F_NONREC flag, this flag should only be used for
deletion requests, specifically, to support non-recursive deletion.
Based on what we discussed during NFWS'17 in Faro.
9) Use NLM_F_NONREC from table and sets in nf_tables.
10) Support for recursive chain deletion. Table and set deletion
commands come with an implicit content flush on deletion, while
chains do not. This patch addresses this inconsistency by adding
the code to perform recursive chain deletions. This also comes with
the bits to deal with the new NLM_F_NONREC netlink flag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support for overloading stateful objects operations
through the select_ops() callback, just as it is implemented for
expressions.
This change is needed for upcoming additions to the stateful objects
infrastructure.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-09-03
Here's one last bluetooth-next pull request for the 4.14 kernel:
- NULL pointer fix in ca8210 802.15.4 driver
- A few "const" fixes
- New Kconfig option for disabling legacy interfaces
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1d6119baf0.
After reverting commit 6d7b857d54 ("net: use lib/percpu_counter API
for fragmentation mem accounting") then here is no need for this
fix-up patch. As percpu_counter is no longer used, it cannot
memory leak it any-longer.
Fixes: 6d7b857d54 ("net: use lib/percpu_counter API for fragmentation mem accounting")
Fixes: 1d6119baf0 ("net: fix percpu memory leaks")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6d7b857d54.
There is a bug in fragmentation codes use of the percpu_counter API,
that can cause issues on systems with many CPUs.
The frag_mem_limit() just reads the global counter (fbc->count),
without considering other CPUs can have upto batch size (130K) that
haven't been subtracted yet. Due to the 3MBytes lower thresh limit,
this become dangerous at >=24 CPUs (3*1024*1024/130000=24).
The correct API usage would be to use __percpu_counter_compare() which
does the right thing, and takes into account the number of (online)
CPUs and batch size, to account for this and call __percpu_counter_sum()
when needed.
We choose to revert the use of the lib/percpu_counter API for frag
memory accounting for several reasons:
1) On systems with CPUs > 24, the heavier fully locked
__percpu_counter_sum() is always invoked, which will be more
expensive than the atomic_t that is reverted to.
Given systems with more than 24 CPUs are becoming common this doesn't
seem like a good option. To mitigate this, the batch size could be
decreased and thresh be increased.
2) The add_frag_mem_limit+sub_frag_mem_limit pairs happen on the RX
CPU, before SKBs are pushed into sockets on remote CPUs. Given
NICs can only hash on L2 part of the IP-header, the NIC-RXq's will
likely be limited. Thus, a fair chance that atomic add+dec happen
on the same CPU.
Revert note that commit 1d6119baf0 ("net: fix percpu memory leaks")
removed init_frag_mem_limit() and instead use inet_frags_init_net().
After this revert, inet_frags_uninit_net() becomes empty.
Fixes: 6d7b857d54 ("net: use lib/percpu_counter API for fragmentation mem accounting")
Fixes: 1d6119baf0 ("net: fix percpu memory leaks")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After ip_route_input() calls ip_route_input_noref(), another
check on skb_dst() is done, but if this fails, we shouldn't
override the return code from ip_route_input_noref(), as it
could have been more specific (i.e. -EHOSTUNREACH).
This also saves one call to skb_dst_force_safe() and one to
skb_dst() in case the ip_route_input_noref() check fails.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Fixes: 9df16efadd ("ipv4: call dst_hold_safe() properly")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listener registers to the FIB notification chain it receives a
dump of the FIB entries and rules from existing address families by
invoking their dump operations.
While we call into these modules we need to make sure they aren't
removed. Do that by increasing their reference count before invoking
their dump operations and decrease it afterwards.
Fixes: 04b1d4e50e ("net: core: Make the FIB notification chain generic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-09-01
This should be the last ipsec-next pull request for this
release cycle:
1) Support netdevice ESP trailer removal when decryption
is offloaded. From Yossi Kuperman.
2) Fix overwritten return value of copy_sec_ctx().
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv6 host table which will be introduced in the
following patches. The fields in the header are added per-use. This header
is global and can be reused by many drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC filters when used as classifiers are bound to TC classes.
However, there is a hidden difference when adding them in different
orders:
1. If we add tc classes before its filters, everything is fine.
Logically, the classes exist before we specify their ID's in
filters, it is easy to bind them together, just as in the current
code base.
2. If we add tc filters before the tc classes they bind, we have to
do dynamic lookup in fast path. What's worse, this happens all
the time not just once, because on fast path tcf_result is passed
on stack, there is no way to propagate back to the one in tc filters.
This hidden difference hurts performance silently if we have many tc
classes in hierarchy.
This patch intends to close this gap by doing the reverse binding when
we create a new class, in this case we can actually search all the
filters in its parent, match and fixup by classid. And because
tcf_result is specific to each type of tc filter, we have to introduce
a new ops for each filter to tell how to bind the class.
Note, we still can NOT totally get rid of those class lookup in
->enqueue() because cgroup and flow filters have no way to determine
the classid at setup time, they still have to go through dynamic lookup.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In conjunction with crypto offload [1], removing the ESP trailer by
hardware can potentially improve the performance by avoiding (1) a
cache miss incurred by reading the nexthdr field and (2) the necessity
to calculate the csum value of the trailer in order to keep skb->csum
valid.
This patch introduces the changes to the xfrm stack and merely serves
as an infrastructure. Subsequent patch to mlx5 driver will put this to
a good use.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg175733.html
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Typically, each TC filter has its own action. All the actions of the
same type are saved in its hash table. But the hash buckets are too
small that it degrades to a list. And the performance is greatly
affected. For example, it takes about 0m11.914s to insert 64K rules.
If we convert the hash table to IDR, it only takes about 0m1.500s.
The improvement is huge.
But please note that the test result is based on previous patch that
cls_flower uses IDR.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 45f119bf93.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf93 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change was a followup to the header prediction removal,
so first revert this as a prerequisite to back out hp removal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian reported UDP xmit drops that could be root caused to the
too small neigh limit.
Current limit is 64 KB, meaning that even a single UDP socket would hit
it, since its default sk_sndbuf comes from net.core.wmem_default
(~212992 bytes on 64bit arches).
Once ARP/ND resolution is in progress, we should allow a little more
packets to be queued, at least for one producer.
Once neigh arp_queue is filled, a rogue socket should hit its sk_sndbuf
limit and either block in sendmsg() or return -EAGAIN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSH (Network Service Header)[1] is a new protocol for service
function chaining, it can be handled as a L3 protocol like
IPv4 and IPv6, Eth + NSH + Inner packet or VxLAN-gpe + NSH +
Inner packet are two typical use cases.
This patch adds NSH header structures and helpers for NSH GSO
support and Open vSwitch NSH support.
[1] https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/
[Jiri: added nsh_hdr() helper and renamed the header struct to "struct
nshhdr" to match the usual pattern. Removed packet type defines, these are
now shared with VXLAN-GPE.]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1. This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.
Two new functions are provided:
(1) rxrpc_kernel_check_call() - This is used to find out the completion
state of a call to guess whether it can be retried and whether it
should be retried.
(2) rxrpc_kernel_retry_call() - Disconnect the call from its current
connection, reset the state and submit it as a new client call to a
new address. The new address need not match the previous address.
A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected. msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.
This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.
Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: David Howells <dhowells@redhat.com>
Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI
stack process new VLAN tags and configure the channel VLAN filter
appropriately.
Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent
for each one, meaning the ncsi_dev_state_config_svf state must be
repeated. An internal list of VLAN tags is maintained, and compared
against the current channel's ncsi_channel_filter in order to keep track
within the state. VLAN filters are removed in a similar manner, with the
introduction of the ncsi_dev_state_config_clear_vids state. The maximum
number of VLAN tag filters is determined by the "Get Capabilities"
response from the channel.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
