Marek Behún says:
====================
net: dsa: qca8k: fix qca8k driver for Turris 1.x
this is v2 of
https://lore.kernel.org/netdev/20231002104612.21898-1-kabel@kernel.org/
Changes since v1:
- fixed a typo in commit message noticed by Simon Horman
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd5485663 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c766e077d9 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d9 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fixes for lynx-28g PHY driver
This series fixes some issues in the Lynx 28G SerDes driver, namely an
oops when unloading the module, a race between the periodic workqueue
and the PHY API, and a race between phy_set_mode_ext() calls on multiple
lanes on the same SerDes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I didn't collect precise data but feels like we've got a lot
of 6.5 fixes here. WiFi fixes are most user-awaited.
Current release - regressions:
- Bluetooth: fix hci_link_tx_to RCU lock usage
Current release - new code bugs:
- bpf: mprog: fix maximum program check on mprog attachment
- eth: ti: icssg-prueth: fix signedness bug in prueth_init_tx_chns()
Previous releases - regressions:
- ipv6: tcp: add a missing nf_reset_ct() in 3WHS handling
- vringh: don't use vringh_kiov_advance() in vringh_iov_xfer(),
it doesn't handle zero length like we expected
- wifi:
- cfg80211: fix cqm_config access race, fix crashes with brcmfmac
- iwlwifi: mvm: handle PS changes in vif_cfg_changed
- mac80211: fix mesh id corruption on 32 bit systems
- mt76: mt76x02: fix MT76x0 external LNA gain handling
- Bluetooth: fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
- l2tp: fix handling of transhdrlen in __ip{,6}_append_data()
- dsa: mv88e6xxx: avoid EEPROM timeout when EEPROM is absent
- eth: stmmac: fix the incorrect parameter after refactoring
Previous releases - always broken:
- net: replace calls to sock->ops->connect() with kernel_connect(),
prevent address rewrite in kernel_bind(); otherwise BPF hooks may
modify arguments, unexpectedly to the caller
- tcp: fix delayed ACKs when reads and writes align with MSS
- bpf:
- verifier: unconditionally reset backtrack_state masks on global
func exit
- s390: let arch_prepare_bpf_trampoline return program size,
fix struct_ops offsets
- sockmap: fix accounting of available bytes in presence of PEEKs
- sockmap: reject sk_msg egress redirects to non-TCP sockets
- ipv4/fib: send netlink notify when delete source address routes
- ethtool: plca: fix width of reads when parsing netlink commands
- netfilter: nft_payload: rebuild vlan header on h_proto access
- Bluetooth: hci_codec: fix leaking memory of local_codecs
- eth: intel: ice: always add legacy 32byte RXDID in supported_rxdids
- eth: stmmac:
- dwmac-stm32: fix resume on STM32 MCU
- remove buggy and unneeded stmmac_poll_controller, depend on NAPI
- ibmveth: always recompute TCP pseudo-header checksum, fix use
of the driver with Open vSwitch
- wifi:
- rtw88: rtw8723d: fix MAC address offset in EEPROM
- mt76: fix lock dependency problem for wed_lock
- mwifiex: sanity check data reported by the device
- iwlwifi: ensure ack flag is properly cleared
- iwlwifi: mvm: fix a memory corruption due to bad pointer arithm
- iwlwifi: mvm: fix incorrect usage of scan API
Misc:
- wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JAtc
-----END PGP SIGNATURE-----
Merge tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth, netfilter, BPF and WiFi.
I didn't collect precise data but feels like we've got a lot of 6.5
fixes here. WiFi fixes are most user-awaited.
Current release - regressions:
- Bluetooth: fix hci_link_tx_to RCU lock usage
Current release - new code bugs:
- bpf: mprog: fix maximum program check on mprog attachment
- eth: ti: icssg-prueth: fix signedness bug in prueth_init_tx_chns()
Previous releases - regressions:
- ipv6: tcp: add a missing nf_reset_ct() in 3WHS handling
- vringh: don't use vringh_kiov_advance() in vringh_iov_xfer(), it
doesn't handle zero length like we expected
- wifi:
- cfg80211: fix cqm_config access race, fix crashes with brcmfmac
- iwlwifi: mvm: handle PS changes in vif_cfg_changed
- mac80211: fix mesh id corruption on 32 bit systems
- mt76: mt76x02: fix MT76x0 external LNA gain handling
- Bluetooth: fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
- l2tp: fix handling of transhdrlen in __ip{,6}_append_data()
- dsa: mv88e6xxx: avoid EEPROM timeout when EEPROM is absent
- eth: stmmac: fix the incorrect parameter after refactoring
Previous releases - always broken:
- net: replace calls to sock->ops->connect() with kernel_connect(),
prevent address rewrite in kernel_bind(); otherwise BPF hooks may
modify arguments, unexpectedly to the caller
- tcp: fix delayed ACKs when reads and writes align with MSS
- bpf:
- verifier: unconditionally reset backtrack_state masks on global
func exit
- s390: let arch_prepare_bpf_trampoline return program size, fix
struct_ops offsets
- sockmap: fix accounting of available bytes in presence of PEEKs
- sockmap: reject sk_msg egress redirects to non-TCP sockets
- ipv4/fib: send netlink notify when delete source address routes
- ethtool: plca: fix width of reads when parsing netlink commands
- netfilter: nft_payload: rebuild vlan header on h_proto access
- Bluetooth: hci_codec: fix leaking memory of local_codecs
- eth: intel: ice: always add legacy 32byte RXDID in supported_rxdids
- eth: stmmac:
- dwmac-stm32: fix resume on STM32 MCU
- remove buggy and unneeded stmmac_poll_controller, depend on NAPI
- ibmveth: always recompute TCP pseudo-header checksum, fix use of
the driver with Open vSwitch
- wifi:
- rtw88: rtw8723d: fix MAC address offset in EEPROM
- mt76: fix lock dependency problem for wed_lock
- mwifiex: sanity check data reported by the device
- iwlwifi: ensure ack flag is properly cleared
- iwlwifi: mvm: fix a memory corruption due to bad pointer arithm
- iwlwifi: mvm: fix incorrect usage of scan API
Misc:
- wifi: mac80211: work around Cisco AP 9115 VHT MPDU length"
* tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
MAINTAINERS: update Matthieu's email address
mptcp: userspace pm allow creating id 0 subflow
mptcp: fix delegated action races
net: stmmac: remove unneeded stmmac_poll_controller
net: lan743x: also select PHYLIB
net: ethernet: mediatek: disable irq before schedule napi
net: mana: Fix oversized sge0 for GSO packets
net: mana: Fix the tso_bytes calculation
net: mana: Fix TX CQE error handling
netlink: annotate data-races around sk->sk_err
sctp: update hb timer immediately after users change hb_interval
sctp: update transport state when processing a dupcook packet
tcp: fix delayed ACKs for MSS boundary condition
tcp: fix quick-ack counting to count actual ACKs of new data
page_pool: fix documentation typos
tipc: fix a potential deadlock on &tx->lock
net: stmmac: dwmac-stm32: fix resume on STM32 MCU
ipv4: Set offload_failed flag in fibmatch results
netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
netfilter: nf_tables: Deduplicate nft_register_obj audit logs
...
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQdXVVFGN5XqKr1Hj7LwZzRsCrn5QUCZR7WExQcem9oYXJAbGlu
dXguaWJtLmNvbQAKCRDLwZzRsCrn5dkMAQCH4MaQ8m9wJwoMnXMUQ0JU5hiwHNeG
eA8lyW2cFhFthAD+JH2phkC5Ka5shBIOusjHRNml/8d/gVhmuXUQKJADSwk=
=ggtG
-----END PGP SIGNATURE-----
Merge tag 'integrity-v6.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity fixes from Mimi Zohar:
"Two additional patches to fix the removal of the deprecated
IMA_TRUSTED_KEYRING Kconfig"
* tag 'integrity-v6.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: rework CONFIG_IMA dependency block
ima: Finish deprecation of IMA_TRUSTED_KEYRING Kconfig
- Potential build failure in CS42L43
- Device Tree bindings clean-up for a superseded patch
-----BEGIN PGP SIGNATURE-----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=g4wJ
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"A couple of small fixes:
- Potential build failure in CS42L43
- Device Tree bindings clean-up for a superseded patch"
* tag 'mfd-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
dt-bindings: mfd: Revert "dt-bindings: mfd: maxim,max77693: Add USB connector"
mfd: cs42l43: Fix MFD_CS42L43 dependency on REGMAP_IRQ
-----BEGIN PGP SIGNATURE-----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=r3VL
-----END PGP SIGNATURE-----
Merge tag 'ovl-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
- Fix for file reference leak regression
- Fix for NULL pointer deref regression
- Fixes for RCU-walk race regressions:
Two of the fixes were taken from Al's RCU pathwalk race fixes series
with his consent [1].
Note that unlike most of Al's series, these two patches are not about
racing with ->kill_sb() and they are also very recent regressions
from v6.5, so I think it's worth getting them into v6.5.y.
There is also a fix for an RCU pathwalk race with ->kill_sb(), which
may have been solved in vfs generic code as you suggested, but it
also rids overlayfs from a nasty hack, so I think it's worth anyway.
Link: https://lore.kernel.org/linux-fsdevel/20231003204749.GA800259@ZenIV/ [1]
* tag 'ovl-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix NULL pointer defer when encoding non-decodable lower fid
ovl: make use of ->layers safe in rcu pathwalk
ovl: fetch inode once in ovl_dentry_revalidate_common()
ovl: move freeing ovl_entry past rcu delay
ovl: fix file reference leak when submitting aio
Mat Martineau says:
====================
mptcp: Fixes and maintainer email update for v6.6
Patch 1 addresses a race condition in MPTCP "delegated actions"
infrastructure. Affects v5.19 and later.
Patch 2 removes an unnecessary restriction that did not allow additional
outgoing subflows using the local address of the initial MPTCP subflow.
v5.16 and later.
Patch 3 updates Matthieu's email address.
====================
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-0-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use my kernel.org account instead.
The other one will bounce by the end of the year.
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-3-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch drops id 0 limitation in mptcp_nl_cmd_sf_create() to allow
creating additional subflows with the local addr ID 0.
There is no reason not to allow additional subflows from this local
address: we should be able to create new subflows from the initial
endpoint. This limitation was breaking fullmesh support from userspace.
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/391
Cc: stable@vger.kernel.org
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-2-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The delegated action infrastructure is prone to the following
race: different CPUs can try to schedule different delegated
actions on the same subflow at the same time.
Each of them will check different bits via mptcp_subflow_delegate(),
and will try to schedule the action on the related per-cpu napi
instance.
Depending on the timing, both can observe an empty delegated list
node, causing the same entry to be added simultaneously on two different
lists.
The root cause is that the delegated actions infra does not provide
a single synchronization point. Address the issue reserving an additional
bit to mark the subflow as scheduled for delegation. Acquiring such bit
guarantee the caller to own the delegated list node, and being able to
safely schedule the subflow.
Clear such bit only when the subflow scheduling is completed, ensuring
proper barrier in place.
Additionally swap the meaning of the delegated_action bitmask, to allow
the usage of the existing helper to set multiple bit at once.
Fixes: bcd9773431 ("mptcp: use delegate action to schedule 3rd ack retrans")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-1-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034 ("netpoll: make ndo_poll_controller() optional")
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 47dd7a540b ("net: add support for STMicroelectronics Ethernet controllers")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While searching for possible refactor of napi_schedule_prep and
__napi_schedule it was notice that the mtk eth driver disable the
interrupt for rx and tx AFTER napi is scheduled.
While this is a very hard to repro case it might happen to have
situation where the interrupt is disabled and never enabled again as the
napi completes and the interrupt is enabled before.
This is caused by the fact that a napi driven by interrupt expect a
logic with:
1. interrupt received. napi prepared -> interrupt disabled -> napi
scheduled
2. napi triggered. ring cleared -> interrupt enabled -> wait for new
interrupt
To prevent this case, disable the interrupt BEFORE the napi is
scheduled.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231002140805.568-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Handle the case when GSO SKB linear length is too large.
MANA NIC requires GSO packets to put only the header part to SGE0,
otherwise the TX queue may stop at the HW level.
So, use 2 SGEs for the skb linear part which contains more than the
packet header.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
sizeof(struct hop_jumbo_hdr) is not part of tso_bytes, so remove
the subtraction from header size.
Cc: stable@vger.kernel.org
Fixes: bd7fc6e195 ("net: mana: Add new MANA VF performance counters for easier troubleshooting")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.
Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- Timerlat is reporting thread interference time without thread noise
events occurrence. It was caused because the thread interference variable
was not reset after the analysis of a timerlat activation that did not
hit the threshold.
- The IRQ handler delay is estimated from the delta of the IRQ latency
reported by timerlat, and the timestamp from IRQ handler start event.
If the delta is near-zero, the drift from the external clock and the
trace event and/or the overhead can cause the value to be negative.
If the value is negative, print a zero-delay.
- IRQ handlers happening after the timerlat thread event but before
the stop tracing were being reported as IRQ that happened before the
*current* IRQ occurrence. Ignore Previous IRQ noise in this condition
because they are valid only for the *next* timerlat activation.
Timerlat user-space:
- Timerlat is stopping all user-space thread if a CPU becomes
offline. Do not stop the entire tool if a CPU is/become offline,
but only the thread of the unavailable CPU. Stop the tool only,
if all threads leave because the CPUs become/are offline.
man-pages:
- Fix command line example in timerlat hist man page.
-----BEGIN PGP SIGNATURE-----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=1BAc
-----END PGP SIGNATURE-----
Merge tag 'rtla-v6.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linux
Pull rtla fixes from Daniel Bristot de Oliveira:
"rtla (Real-Time Linux Analysis) tool fixes.
Timerlat auto-analysis:
- Timerlat is reporting thread interference time without thread noise
events occurrence. It was caused because the thread interference
variable was not reset after the analysis of a timerlat activation
that did not hit the threshold.
- The IRQ handler delay is estimated from the delta of the IRQ
latency reported by timerlat, and the timestamp from IRQ handler
start event. If the delta is near-zero, the drift from the external
clock and the trace event and/or the overhead can cause the value
to be negative. If the value is negative, print a zero-delay.
- IRQ handlers happening after the timerlat thread event but before
the stop tracing were being reported as IRQ that happened before
the *current* IRQ occurrence. Ignore Previous IRQ noise in this
condition because they are valid only for the *next* timerlat
activation.
Timerlat user-space:
- Timerlat is stopping all user-space thread if a CPU becomes
offline. Do not stop the entire tool if a CPU is/become offline,
but only the thread of the unavailable CPU. Stop the tool only, if
all threads leave because the CPUs become/are offline.
man-pages:
- Fix command line example in timerlat hist man page"
* tag 'rtla-v6.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linux:
rtla: fix a example in rtla-timerlat-hist.rst
rtla/timerlat: Do not stop user-space if a cpu is offline
rtla/timerlat_aa: Fix previous IRQ delay for IRQs that happens after thread sample
rtla/timerlat_aa: Fix negative IRQ delay
rtla/timerlat_aa: Zero thread sum after every sample analysis
Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.
This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.
Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg590224.html
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/75465785f8ee5df2fb3acdca9b8fafdc18984098.1696172660.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.
In the collision scenario below:
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021]
when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().
However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.
This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().
This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/fd17356abe49713ded425250cc1ae51e9f5846c6.1696172325.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
tp->rcv_nxt - tp->rcv_wup > icsk->icsk_ack.rcv_mss ||
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED2) ||
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED) &&
!inet_csk_in_pingpong_mode(sk))) &&
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Xin Guo <guoxin0309@gmail.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-2-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.
The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.
When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.
And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.
The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.
Fixes: fc6415bcb0 ("[TCP]: Fix quick-ack decrementing with TSO.")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-1-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=YLDi
-----END PGP SIGNATURE-----
Merge tag 'nf-23-10-04' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
netfilter patches for net
First patch resolves a regression with vlan header matching, this was
broken since 6.5 release. From myself.
Second patch fixes an ancient problem with sctp connection tracking in
case INIT_ACK packets are delayed. This comes with a selftest, both
patches from Xin Long.
Patch 4 extends the existing nftables audit selftest, from
Phil Sutter.
Patch 5, also from Phil, avoids a situation where nftables
would emit an audit record twice. This was broken since 5.13 days.
Patch 6, from myself, avoids spurious insertion failure if we encounter an
overlapping but expired range during element insertion with the
'nft_set_rbtree' backend. This problem exists since 6.2.
* tag 'nf-23-10-04' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
netfilter: nf_tables: Deduplicate nft_register_obj audit logs
selftests: netfilter: Extend nft_audit.sh
selftests: netfilter: test for sctp collision processing in nf_conntrack
netfilter: handle the connecting collision properly in nf_conntrack_proto_sctp
netfilter: nft_payload: rebuild vlan header on h_proto access
====================
Link: https://lore.kernel.org/r/20231004141405.28749-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
tipc_crypto_work_rx() <workqueue>
--> tipc_crypto_key_distr()
--> tipc_bcast_xmit()
--> tipc_bcbase_xmit()
--> tipc_bearer_bc_xmit()
--> tipc_crypto_xmit()
--> tipc_ehdr_build()
--> tipc_crypto_key_revoke()
--> spin_lock(&tx->lock)
<timer interrupt>
--> tipc_disc_timeout()
--> tipc_bearer_xmit_skb()
--> tipc_crypto_xmit()
--> tipc_ehdr_build()
--> tipc_crypto_key_revoke()
--> spin_lock(&tx->lock) <deadlock here>
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Link: https://lore.kernel.org/r/20230927181414.59928-1-dg573847474@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9 ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.
The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device
Fixes: 36c5100e85 ("IPv4: Add "offload failed" indication to routes")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230926182730.231208-1-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This kselftest fixes update for Linux 6.6-rc5 consists of one single
fix to Makefile to fix the incorrect TARGET name for uevent test.
-----BEGIN PGP SIGNATURE-----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=W9Tx
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"One single fix to Makefile to fix the incorrect TARGET name for uevent
test"
* tag 'linux-kselftest-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix wrong TARGET in kselftest top level Makefile
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
-----BEGIN PGP SIGNATURE-----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=OL/S
-----END PGP SIGNATURE-----
Merge tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Quite a collection of fixes this time, really too many
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
* tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (32 commits)
wifi: iwlwifi: mvm: Fix incorrect usage of scan API
wifi: mac80211: Create resources for disabled links
wifi: cfg80211: avoid leaking stack data into trace
wifi: mac80211: allow transmitting EAPOL frames with tainted key
wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
wifi: cfg80211: Fix 6GHz scan configuration
wifi: mac80211: fix potential key leak
wifi: mac80211: fix potential key use-after-free
wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
wifi: brcmfmac: Replace 1-element arrays with flexible arrays
wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
wifi: rtw88: rtw8723d: Fix MAC address offset in EEPROM
rfkill: sync before userspace visibility/changes
wifi: mac80211: fix mesh id corruption on 32 bit systems
wifi: cfg80211: add missing kernel-doc for cqm_rssi_work
wifi: cfg80211: fix cqm_config access race
wifi: iwlwifi: mvm: Fix a memory corruption issue
wifi: iwlwifi: Ensure ack flag is properly cleared.
wifi: iwlwifi: dbg_ini: fix structure packing
iwlwifi: mvm: handle PS changes in vif_cfg_changed
...
====================
Link: https://lore.kernel.org/r/20230927095835.25803-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZRqk1wAKCRDbK58LschI
g8GRAQC4E0bw6BTFRl0b3MxvpZES6lU0BUtX2gKVK4tLZdXw/wEAmTlBXQqNzF3b
BkCQknVbFTSw/8l8pzUW123Fb46wUAQ=
=E3hd
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-10-02
We've added 11 non-merge commits during the last 12 day(s) which contain
a total of 12 files changed, 176 insertions(+), 41 deletions(-).
The main changes are:
1) Fix BPF verifier to reset backtrack_state masks on global function
exit as otherwise subsequent precision tracking would reuse them,
from Andrii Nakryiko.
2) Several sockmap fixes for available bytes accounting,
from John Fastabend.
3) Reject sk_msg egress redirects to non-TCP sockets given this
is only supported for TCP sockets today, from Jakub Sitnicki.
4) Fix a syzkaller splat in bpf_mprog when hitting maximum program
limits with BPF_F_BEFORE directive, from Daniel Borkmann
and Nikolay Aleksandrov.
5) Fix BPF memory allocator to use kmalloc_size_roundup() to adjust
size_index for selecting a bpf_mem_cache, from Hou Tao.
6) Fix arch_prepare_bpf_trampoline return code for s390 JIT,
from Song Liu.
7) Fix bpf_trampoline_get when CONFIG_BPF_JIT is turned off,
from Leon Hwang.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Use kmalloc_size_roundup() to adjust size_index
selftest/bpf: Add various selftests for program limits
bpf, mprog: Fix maximum program check on mprog attachment
bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
bpf, sockmap: Add tests for MSG_F_PEEK
bpf, sockmap: Do not inc copied_seq when PEEK flag set
bpf: tcp_read_skb needs to pop skb regardless of seq
bpf: unconditionally reset backtrack_state masks on global func exit
bpf: Fix tr dereferencing
selftests/bpf: Check bpf_cubic_acked() is called via struct_ops
s390/bpf: Let arch_prepare_bpf_trampoline return program size
====================
Link: https://lore.kernel.org/r/20231002113417.2309-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.
There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.
It also causes spurious insertion failures:
$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s { 0 - 2 }
^^^^^^
Failed to insert 0 - 2 given:
table ip t {
set s {
type inet_service
flags interval,timeout
timeout 2s
gc-interval 2s
}
}
The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.
Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:
if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
return -ENOTEMPTY;
rbe_ge was erased by the synchronous gc, we should not have done this
check. Next attempt won't find it, so retry results in successful
insertion.
Restart in-kernel to avoid such spurious errors.
Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.
Even in this case, this cannot loop forever, on each retry an existing
element has been removed.
As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.
After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.
Fixes: c9e6978e27 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Florian Westphal <fw@strlen.de>
When adding/updating an object, the transaction handler emits suitable
audit log entries already, the one in nft_obj_notify() is redundant. To
fix that (and retain the audit logging from objects' 'update' callback),
Introduce an "audit log free" variant for internal use.
Fixes: c520292f29 ("audit: log nftables configuration change events once per table")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com> (Audit)
Signed-off-by: Florian Westphal <fw@strlen.de>
Add tests for sets and elements and deletion of all kinds. Also
reorder rule reset tests: By moving the bulk rule add command up, the
two 'reset rules' tests become identical.
While at it, fix for a failing bulk rule add test's error status getting
lost due to its use in a pipe. Avoid this by using a temporary file.
Headings in diff output for failing tests contain no useful data, strip
them.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
This patch adds a test case to reproduce the SCTP DATA chunk retransmission
timeout issue caused by the improper SCTP collision processing in netfilter
nf_conntrack_proto_sctp.
In this test, client sends a INIT chunk, but the INIT_ACK replied from
server is delayed until the server sends a INIT chunk to start a new
connection from its side. After the connection is complete from server
side, the delayed INIT_ACK arrives in nf_conntrack_proto_sctp.
The delayed INIT_ACK should be dropped in nf_conntrack_proto_sctp instead
of updating the vtag with the out-of-date init_tag, otherwise, the vtag
in DATA chunks later sent by client don't match the vtag in the conntrack
entry and the DATA chunks get dropped.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
In Scenario A and B below, as the delayed INIT_ACK always changes the peer
vtag, SCTP ct with the incorrect vtag may cause packet loss.
Scenario A: INIT_ACK is delayed until the peer receives its own INIT_ACK
192.168.1.2 > 192.168.1.1: [INIT] [init tag: 1328086772]
192.168.1.1 > 192.168.1.2: [INIT] [init tag: 1414468151]
192.168.1.2 > 192.168.1.1: [INIT ACK] [init tag: 1328086772]
192.168.1.1 > 192.168.1.2: [INIT ACK] [init tag: 1650211246] *
192.168.1.2 > 192.168.1.1: [COOKIE ECHO]
192.168.1.1 > 192.168.1.2: [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: [COOKIE ACK]
Scenario B: INIT_ACK is delayed until the peer completes its own handshake
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021] *
This patch fixes it as below:
In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].
In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)
In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
(Scenario D)
Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.
There are also other Scenarios where it should allow the packet through,
addressed by the processing above:
Scenario C: new CT is created by INIT_ACK.
Scenario D: start INIT on the existing ESTABLISHED ct.
Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
(both side are stopped, then start new connection again in hours)
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]
Fixes: 9fb9cbb108 ("[NETFILTER]: Add nf_conntrack subsystem.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
nft can perform merging of adjacent payload requests.
This means that:
ether saddr 00:11 ... ether type 8021ad ...
is a single payload expression, for 8 bytes, starting at the
ethernet source offset.
Check that offset+length is fully within the source/destination mac
addersses.
This bug prevents 'ether type' from matching the correct h_proto in case
vlan tag got stripped.
Fixes: de6843be30 ("netfilter: nft_payload: rebuild vlan header when needed")
Reported-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Florian Westphal <fw@strlen.de>
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516 ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the while loop of vringh_iov_xfer(), `partlen` could be 0 if one of
the `iov` has 0 lenght.
In this case, we should skip the iov and go to the next one.
But calling vringh_kiov_advance() with 0 lenght does not cause the
advancement, since it returns immediately if asked to advance by 0 bytes.
Let's restore the code that was there before commit b8c06ad4d6
("vringh: implement vringh_kiov_advance()"), avoiding using
vringh_kiov_advance().
Fixes: b8c06ad4d6 ("vringh: implement vringh_kiov_advance()")
Cc: stable@vger.kernel.org
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable Fix:
* Revert "SUNRPC dont update timeout value on connection reset"
* NFSv4: Fix a state manager thread deadlock regression
Bugfixes:
* Fix a potential NULL pointer dereference in nfs_inode_remove_request()
* Fix a rare NULL pointer dereference in xs_tcp_tls_setup_socket()
* Fix long delay before failing a TLS mount when server does not support TLS
* Fix various NFS state manager issues
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEnZ5MQTpR7cLU7KEp18tUv7ClQOsFAmUcZYIACgkQ18tUv7Cl
QOtNyBAA0RaAI4D5Em3/JxmdaqoK8LgSlw3gSup0VoWG1/gyKlt0wW6gDPzffIVK
pb5wTMdDVzZmbamll15gvOJYYY4tEVpMGg5unR5LIIhS/5Z5TbGEU3ioO7xsKnTI
0FYtQ0fEXJaPqVLUh3xY/W7Bn2wdehD2bqSfYakddL1C9+cc1XRnxA5BLEL67ZQ4
zlBhI2acv/9eEGZjVYdI8cv+27WvQY+ud21VZrEGPuztZklfwipNBLr3qT2WpwTU
vLqp5Py1PydEV7CHIrPtAKhQIuxlYr4m//YXMD4jU4bQuHql0TmUGzJEvfsOzIZn
LPEJy2kIA37/Rm92lPeZ0m6E/bwXz8iv7HTFpvgIf6ZIY2PSsVNFZYovhSv/yV8N
qoRcpBswi5nYXZ2KoVfjp+J8NQXWjVS/ODoycdCCWVKEjrVh5oFPfYH67jph4o7l
E0QaSNKPhy2OHWVgf8hQNJ+Fi34qvxYG1F2RmaTcJybyco1o4jVQ4WJhNGNJbLWH
dorEko6n82XPBB9+1Qo2nUqLwNgNdyHmmqBO0OG5tJH3mrIrRPJ8DBjAIWggDGSH
pfB2GftuTuXIUvY97PxZlW0Iz1ZKX6NPFS/gtHJizbVGl+E5wttxbPPJNsApA/v1
ZoE2K2cgSsyqTXR6arf55EJZyO4oAnmYEPQLu5jlyV83vQQz/xY=
=qUGw
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-6.6-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"Stable fixes:
- Revert "SUNRPC dont update timeout value on connection reset"
- NFSv4: Fix a state manager thread deadlock regression
Fixes:
- Fix potential NULL pointer dereference in nfs_inode_remove_request()
- Fix rare NULL pointer dereference in xs_tcp_tls_setup_socket()
- Fix long delay before failing a TLS mount when server does not
support TLS
- Fix various NFS state manager issues"
* tag 'nfs-for-6.6-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
nfs: decrement nrequests counter before releasing the req
SUNRPC/TLS: Lock the lower_xprt during the tls handshake
Revert "SUNRPC dont update timeout value on connection reset"
NFSv4: Fix a state manager thread deadlock regression
NFSv4: Fix a nfs4_state_manager() race
SUNRPC: Fail quickly when server does not recognize TLS
