Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.
Update debugfs code to use the correct format specifier for u64.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf329 ("i40e: driver core headers")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the reason of null pointer dereference in sync VSI filters.
Added new I40E_VSI_RELEASING flag to signalize deleting and releasing
of VSI resources to sync this thread with sync filters subtask.
Without this patch it is possible to start update the VSI filter list
after VSI is removed, that's causing a kernel oops.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert i40e to use the auxiliary bus infrastructure to export
the RDMA functionality of the device to the RDMA driver.
Register i40e client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the new auxiliary rdma driver (irdma) to
attach to.
The global i40e_register_client and i40e_unregister_client symbols
will be obsoleted once irdma replaces i40iw in the kernel
for the X722 device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The minimum size of admin send/receive queue is 1 and 2 respectively.
The admin send queue can't be set to 1 because in that case, the
firmware would fail to init.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.
Fixes: d43d60e5eb ("i40e: ensure reset occurs when disabling VF")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow user to specify VLAN field and add it to flow director. Show VLAN
field in "ethtool -n ethx" command.
Handle VLAN type and tag field provided by ethtool command. Refactored
filter addition, by replacing static arrays with runtime dummy packet
creation, which allows specifying VLAN field.
Previously, VLAN field was omitted.
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow director for IPv6 is not supported.
1) Implementation of support for IPv6 flow director.
2) Added handlers for addition of TCP6, UDP6, SCTP6, IPv6.
3) Refactored legacy code to make it more generic.
4) Added packet templates for TCP6, UDP6, SCTP6, IPv6.
5) Added handling of IPv6 source and destination address for flow director.
6) Improved argument passing for source and destination portin TCP6, UDP6
and SCTP6.
7) Added handling of ethtool -n for IPv6, TCP6,UDP6, SCTP6.
8) Used correct bit flag regarding FLEXOFF field of flow director data
descriptor.
Without this patch, there would be no support for flow director on IPv6,
TCP6, UDP6, SCTP6.
Tested based on x710 datasheet by using:
ethtool -N enp133s0f0 flow-type tcp4 src-port 13 dst-port 37 user-def 0x44142 action 1
ethtool -N enp133s0f0 flow-type tcp6 src-port 13 dst-port 40 user-def 0x44142 action 2
ethtool -N enp133s0f0 flow-type udp4 src-port 20 dst-port 40 user-def 0x44142 action 3
ethtool -N enp133s0f0 flow-type udp6 src-port 25 dst-port 40 user-def 0x44142 action 4
ethtool -N enp133s0f0 flow-type sctp4 src-port 55 dst-port 65 user-def 0x44142 action 5
ethtool -N enp133s0f0 flow-type sctp6 src-port 60 dst-port 40 user-def 0x44142 action 6
ethtool -N enp133s0f0 flow-type ip4 src-ip 1.1.1.1 dst-ip 1.1.1.4 user-def 0x44142 action 7
ethtool -N enp133s0f0 flow-type ip6 src-ip fe80::3efd:feff:fe6f:bbbb dst-ip fe80::3efd:feff:fe6f:aaaa user-def 0x44142 action 8
Then send traffic from client which matches the criteria provided to ethtool.
Observe that packets are redirected to user set queues with ethtool -S <interface>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add extra handling on changing the "disable-fw-lldp" private
flag to properly initialize software based DCB feature.
Add default configuration of DCB functionality when Firmware
LLDP agent is turned off, in case of driver probe and device
reset on reconfiguration.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
Default configuration and new initialization flow for software based
DCB is required. If LLDP agent is turned off in BIOS, or after
setting private flag ("disable-fw-lldp on"). The driver initializes
DCB functionality with default values, one traffic class with 100%
bandwidth allocated.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When removing VFs for PF added to bridge there was
an error I40E_AQ_RC_EINVAL. It was caused by not properly
resetting and reinitializing PF when adding/removing VFs.
Changed how reset is performed when adding/removing VFs
to properly reinitialize PFs VSI.
Fixes: fc60861e9b ("i40e: start up in VEPA mode by default")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36ee ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the "shared port table" to convert i40e to the new
infra.
i40e did not have any reference tracking, locking is also dodgy
because rtnl gets released while talking to FW, so port may get
removed from the table while it's getting added etc.
On the good side i40e does not seem to be using the ports for
TX so we can remove the table from the driver state completely.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e NIC supports two flavors of HW descriptors, 16 and 32
byte. The latter has, obviously, room for more offloading
information. However, the only fields of the 32B HW descriptor that is
being used by the driver, is also available in the 16B descriptor.
In other words; Reading and writing 32 bytes instead of 16 byte is a
waste of bus bandwidth.
This commit starts using 16 byte descriptors instead of 32 byte
descriptors.
For AF_XDP the rx_drop benchmark was improved by 2%.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After OS requests to down a link on a physical network port, the
traffic is no longer being processed but the physical link with
a link partner is still established.
Currently there is a feature (Link down on close) which allows
to physically bring the link down (after OS request).
With this patch new feature with similar capability is introduced:
TOTAL_PORT_SHUTDOWN
Allows to physically disable the link on the NIC's port.
If enabled, (after link down request from the OS)
no link, traffic or led activity is possible on that port.
If I40E_FLAG_TOTAL_PORT_SHUTDOWN is enabled, the
I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED must be explicitly forced to
true and cannot be disabled at that time.
The functionalities are exclusive in terms of configuration, but
they also have similar behavior (allowing to disable physical link
of the port), with following differences:
- LINK_DOWN_ON_CLOSE_ENABLED is configurable at host OS run-time
and is supported by whole family of 7xx Intel Ethernet Controllers
- TOTAL_PORT_SHUTDOWN may be enabled only before OS loads (in BIOS)
only if motherboard's BIOS and NIC's FW has support of it
- when LINK_DOWN_ON_CLOSE_ENABLED is used, the link is being brought
down by sending phy_type=0 to NIC's FW
- when TOTAL_PORT_SHUTDOWN is used, phy_type is not altered, instead
the link is being brought down by clearing bit
(I40E_AQ_PHY_ENABLE_LINK) in abilities field of
i40e_aq_set_phy_config structure
Introduced changes:
- new private flag I40E_FLAG_TOTAL_PORT_SHUTDOWN for handling the
feature
- probe of NVM if the feature was enabled at driver's port
initialization
- special handling on link-down procedure to let FW physically
shutdown the port if the feature was enabled
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Remove all the unused defines as they are just dead weight.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move i40e_client.h to include/linux/net/intel/*
since its shared between i40iw and i40e.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
This patch prepares ground for the next VF MAC address change fix.
It lets untrusted VF to delete any VF mac filter, but it still
doesn't let untrusted VF to add mac filter not setup by PF.
It removes information duplication in num_mac mac filters counter.
And improves exact h/w mac filters usage checking in the
i40e_check_vf_permission() function by counting mac2add_cnt.
It also improves logging because now all mac addresses will be validated
first and corresponding messages will be logged.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The macros used to specify the cloud filter fields are intended to be
individual bits. Declare them using the BIT() macro to make their
intention a little more clear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit
'5098850c9b9b ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:
echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000
So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes missing call of i40e_update_veb_stats() in function
i40e_get_ethtool_stats() to update stats data of VEB and VEB TC
counters before they are written into ethtool buffer.
Before the patch ethtool counters may fell behind interface counters.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables macvlan offloads for i40e. The idea is to use
channels as macvlan interfaces. The channels are VSIs of
type VMDQ. When the first macvlan is created, the maximum number of
channels possible are created. From then on, as a macvlan interface
is created, a macvlan filter is added to these already created
channels (VSIs).
This patch utilizes subordinate device traffic classes to make queue
groups(channels) available for an upper device like a macvlan.
Steps to configure macvlan offloads:
1. ethtool -K ethx l2-fwd-offload on
2. ip link add link ethx name macvlan1 type macvlan
3. ip addr add <address> dev macvlan1
4. ip link set macvlan1 up
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.
To fix this:
* introduce new VSI members - num_tx_desc and num_rx_desc in favour of
num_desc
* set them in i40e_set_ringparam to user's values
* set them to default values in i40e_set_num_rings_in_vsi only when they
don't have previous values
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.
These additional AQ commands are part of the interface used by
the NVMUpdate tool. The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands. The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where PTP is running on the hardware clock, but the kernel
system time is not being synced, a device reset can mess up the clock
time.
This occurs because we reset the clock time based on the kernel time
every reset. This causes us to potentially completely reset the PTP
time, and can cause unexpected behavior in programs like ptp4l.
Avoid this by saving the PTP time prior to device reset, and then
restoring using that time after the reset.
Directly restoring the PTP time we saved isn't perfect, because time
should have continued running, but the clock will essentially be stopped
during the reset. This is still better than the current solution of
assuming that the PTP HW clock is synced to the CLOCK_REALTIME.
We can do even better, by saving the ktime and calculating
a differential, using ktime_get(). This is based on CLOCK_MONOTONIC, and
allows us to get a fairly precise measure of the time difference between
saving and restoring the time.
Using this, we can update the saved PTP time, and use that as the value
to write to the hardware clock registers. This, of course is not perfect.
However, it does help ensure that the PTP time is restored as close as
feasible to the time it should have been if the reset had not occurred.
During device initialization, continue using the system time as the
source for the creation of the PTP clock, since this is the best known
current time source at driver load.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces DDP (Dynamic Device Personalization) which allows
loading profiles that change the way internal parser interprets processed
frames. To load DDP profiles it utilizes ethtool flash feature. The files
with recipes must be located in /var/lib/firmware directory. Afterwards
the recipe can be loaded by invoking:
ethtool -f <if_name> <file_name> 100
ethtool -f <if_name> - 100
See further details of this feature in the i40e documentation, or
visit
https://www.intel.com/content/www/us/en/architecture-and-technology/ethernet/dynamic-device-personalization-brief.html
The driver shall verify DDP profile can be loaded in accordance with
the rules:
* Package with Group ID 0 are exclusive and can only be loaded the first.
* Packages with Group ID 0x01-0xFE can only be loaded simultaneously
with the packages from the same group.
* Packages with Group ID 0xFF are compatible with all other packages.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit f3fef2b6e1 ("i40e: Remove umem from VSI") a regression was
introduced; When the VSI was reset, the setup code would try to enable
AF_XDP ZC unconditionally (as long as there was a umem placed in the
netdev._rx struct). Here, we add a bitmap to the VSI that tracks if a
certain queue pair has been "zero-copy enabled" via the ndo_bpf. The
bitmap is used in i40e_xsk_umem, and enables zero-copy if and only if
XDP is enabled, the corresponding qid in the bitmap is set and the
umem is non-NULL.
Fixes: f3fef2b6e1 ("i40e: Remove umem from VSI")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_xsk_umem function was explicitly inlined in i40e.h. There is
no reason for that, so move it to i40e_main.c instead.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for setting/getting FEC configuration
using ethtool options:
set/show-priv-flags rs-fec/base-r-fec
set/show-fec off/rs/baser/auto for kernels version >= 4.14
Signed-off-by: Damian Dybek <damian.dybek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As current implementation of netdev already contains and provides
umems for us, we no longer have the need to contain these
structures in i40e_vsi.
Refactor the code to operate on netdev-provided umems.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows disabling FW LLDP agent on X722 devices.
It also changes a source of information for this feature from
pf->hw_features to pf->hw.flags which are set in i40e_init_adminq.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A scenario has been found in which simultaneous
addition/removal and modification of VF's might cause
unstable behaviour, up to and including kernel panics.
Protect the methods that create/modify/destroy VF's
by locking them behind an atomically set bit in PF status
bitfield.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds zero-copy Rx support for AF_XDP sockets. Instead of
allocating buffers of type MEM_TYPE_PAGE_SHARED, the Rx frames are
allocated as MEM_TYPE_ZERO_COPY when AF_XDP is enabled for a certain
queue.
All AF_XDP specific functions are added to a new file, i40e_xsk.c.
Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS
will allocate a new buffer and copy the zero-copy frame prior passing
it to the kernel stack.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The expectation of the ops VIRTCHNL_OP_ENABLE_QUEUES and
VIRTCHNL_OP_DISABLE_QUEUES is that the queue map sent by
the VF is taken into account when enabling/disabling
queues in the VF VSI. This patch makes sure that happens.
By breaking out the individual queue set up functions so
that they can be called directly from the i40e_virtchnl_pf.c
file, only the queues as specified by the queue bit map that
accompanies the enable/disable queues ops will be handled.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When operating at 1GbE, the base incval for the PTP clock is so large
that multiplying it by numbers close to the max_adj can overflow the
u64.
Rather than attempting to limit the max_adj to a value small enough to
avoid overflow, instead calculate the incvalue adjustment based on the
40GbE incvalue, and then multiply that by the scaling factor for the
link speed.
This sacrifices a small amount of precision in the adjustment but we
avoid erratic behavior of the clock due to the overflow caused if ppb is
very near the maximum adjustment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.
The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.
The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the gaps created by the recent refactor of various feature flags
that have moved to the state field. Use only a u32 now that we have
fewer than 32 flags in the field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The iWarp client flags are all potentially changed when the RTNL lock is
not held, so they should not be part of the pf->flags variable. Instead,
move them into the state field so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag is modified outside of the RTNL lock and thus should not be
part of the pf->flags variable.
Use a state bit instead, so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The two Flow Directory auto disable flags are used at run time to mark
when the flow director features needed to be disabled. Thus the flags
could change even when the RTNL lock is not held.
They also have some code constructions which really should be
test_and_set or test_and_clear using atomic bit operations.
Create new state fields to mark this, and stop including them in
pf->flags.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag is modified during run time, possibly even when the RTNL lock
is not held. Additionally it has a few places which should be using
test_and_set or test_and_clear atomic bit operations.
Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the
ole I40E_FLAG_UDP_FILTER_SYNC flag.
This is part of a larger effort to remove the need for using cmpxchg64
in i40e_set_priv_flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
