The TDM mode using PCM format now has two-bit right shift due to the
format configuration in the driver. According to Figure 4-13 in the
CS53L30 datasheet, using ASP_SCLK_INV = 0 and SHIFT_LEFT = 1 should
be the correct combination to create one-bit right shift for the DSP
type A format.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum slot number of CS53L30 is 4 while it should support
the situation that's less than 4 channels based on the rx_mask.
So when the driver validates the last slot location, it should
check the last active slot instead of always the 4th one.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like in Skylake, Kabylake also uses combo jack so add Kabylake to
DMI match for combo jack configuration.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake platform is similar to Skylake. So, add the device id.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT platforms use RT5645 codec which has entry 10EC5640 so add it.
Also add DMI quirk for jack detection.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
[Jack detection]
Suggested-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add an alsa control for DAC1 digital volume control function
selection. The options are:
0: Gain update immediately
1: Gain update when a zero crossing
2: Gain update when a zero crossing with a soft ramp
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_PRIV_INDEX(0x6a) indicate the address of PR- registers. So,
it should be volatile.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add supports for 16k (wideband BT) and add a general compatible
string "linux,bt-sco"
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
reg-8a assign the tracking source for each ASRC tracker. The default
value is 0x0000 which means all ASRC trackers will track LRCK1. But
in most cases, we wish each ASRC tracker track the corresponding LRCK.
i.e. ASRC1 tracks LRCK1, ASRC2 tracks LRCK2 and so on. So, we rewrite
reg-8a as 0x0120.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of reg-2f in codec rt5650 is 0x5002, not 0x1002.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_optional() returns NULL when the gpio is not assigned.
So the if (PTR_ERR(cs35l33->reset_gpio) == -ENOENT) test is always false.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added cs35l33 driver produces a harmless warning when
CONFIG_PM is disabled:
sound/soc/codecs/cs35l33.c:908:12: error: 'cs35l33_runtime_suspend' defined but not used [-Werror=unused-function]
sound/soc/codecs/cs35l33.c:868:12: error: 'cs35l33_runtime_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to shut up the warning
regardless of the configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is done by ASoC core now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code uses devm_request_threaded_irq() so it does not need to
explicitly call free_irq() in .probe error path and .remove.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs35l33.c:1301:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l33 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdac_hdmi codec driver prints the ELD information everytime an
external monitor is connected. Make it so that the information is only
printed when someone trying to debug the driver explicitly enables it.
print_hex_dump_bytes (which just calls print_hex_dump) uses
printk(KERN_DEBUG,... which is different from dev_dbg used elsewhere in
the driver: it's always enabled at compile-time. Change it to
print_hex_dump_debug for logging consistency.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change converts the driver from using the of_* functions to using
the device_* and fwnode_* functions for accssing FW related data.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec chip has a physical MUTE pin to let users control it via
GPIO. So this patch add a mute control support to the driver.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reorders the clearing of the DMA masks to avoid potential
artefacts being introduced.
Signed-off-by: Simon Trimmer <simont@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is using the set_bias_level to control the power on and
off so it should get SND_SOC_BIAS_OFF in order to proceed normal
powering sequences. This patch enables the idle_bias_off option so
the DAPM core will set the bias level to SND_SOC_BIAS_OFF instead
of stopping at SND_SOC_BIAS_STANDBY.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/cs53l30.c:182:20: warning:
symbol 'input1_sel_values' was not declared. Should it be static?
sound/soc/codecs/cs53l30.c:202:20: warning:
symbol 'input2_sel_values' was not declared. Should it be static?
sound/soc/codecs/cs53l30.c:734:20: warning:
symbol 'cs53l30_src_rates' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 79901317ce ("n_tty: Don't flush buffer when closing ldisc"),
introduced in v3.10, revealed a bug in the cx20442 codec driver
which has never been setting tty->receive_room on line discipline
open as it should from the beginning. Fix it.
Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the suspend callback to accompany the existing resume operation.
With the suspend/resume callbacks the regmap (regcache) state handling
can follow the recommended sequence.
Based on commit a2ebd58627 ("ASoC: ak4642: Implement suspend
callback") by Peter Ujfalusi <peter.ujfalusi@ti.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
During system resume:
kernel BUG at drivers/base/regmap/regcache.c:347!
...
PC is at regcache_sync+0x1c/0x128
LR is at ak4613_resume+0x28/0x34
The ak4613 driver is using a regmap cache sync to restore the
configuration of the chip on resume but does not actually define a
register cache which means that the resume is never going to work and we
trigger asserts in regmap. Fix this by enabling caching.
Based on commit d3030d1196 ("ASoC: ak4642: Enable cache usage to
fix crashes on resume") by Mark Brown <broonie@kernel.org>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8940 driver is using a regmap cache sync to restore the
configuration of the chip when switching from OFF to STANDBY, but does
not actually define a register cache which means that the restore is
never going to work and we trigger asserts in regmap. Fix this by
enabling caching.
Based on commit d3030d1196 ("ASoC: ak4642: Enable cache usage to
fix crashes on resume") by Mark Brown <broonie@kernel.org>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The devices from the ADAU17X1 family all have a MCLK clock input which
supplies the master clock for the device. The master clock is used as the
input clock for the PLL. Currently the MCLK rate as well as the desired PLL
output frequency need to be supplied by calling snd_soc_dai_set_pll() form
a machine driver.
Add support for specifying the MCLK using the common clock framework. In
addition to that also automatically configure the PLL to a suitable rate
if the master clock was provided using the CCW. This allows to use the
CODEC driver without any special configuration requirements from the
machine driver.
While the PLL output frequency can be configured over a (more or less)
continuous range the narrowness of the range and the other constraints of
the clocking tree usually only result in two output frequencies that will
actually be chosen. One for 44.1kHz based rates and one for 48kHz based
rates, these are the rates that the automatic PLL configuration will use.
For the rare case where a non-standard setup is required a machine driver
can disable the auto-configuration and configure a custom frequency using
the existing mechanisms.
If the common clock framework is not enabled clk_get() will return NULL and
the driver will function as before and the clock rate needs to be
configured manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent commit made a few arrays 'const', but also added the
same attribute to a function return type, where it makes no
sense, and we get a warning when building with W=1:
sound/soc/codecs/arizona.c:1725:27: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
static const char * const arizona_dai_clk_str(int clk_id)
This removes it again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DAIFMT_IB_NF = 0x3 (11b) | SND_SOC_DAIFMT_IB_IF = 0x4 (100b)
creates a mask 0x7 (111b) which also includes SND_SOC_DAIFMT_NB_IF
= 0x2 (10b).
So this patch uses the traditional way to check the clock inversion.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc -Wextra warns about an obvious but harmless typo in the
pcm1681_writeable_reg function, which has an extra 'register
keyword', and in pcm179x, which has a second copy of that
declaration:
sound/soc/codecs/pcm1681.c:76:42: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
sound/soc/codecs/pcm179x.c:62:42: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
For consistency with the rest of the file, I'm changing this from
'unsigned register' to 'unsigned int', which has the same meaning
but causes no warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When GPIOLIB is disabled, we don't see the declarations from
gpio/consumer.h, so we have to include the header explicitly
to avoid this build error:
sound/soc/codecs/cs53l30.c: In function 'cs53l30_i2c_probe':
sound/soc/codecs/cs53l30.c:931:24: error: implicit declaration of function 'devm_gpiod_get_optional' [-Werror=implicit-function-declaration]
cs53l30->reset_gpio = devm_gpiod_get_optional(dev, reset,
^~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/cs53l30.c:932:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
sound/soc/codecs/cs53l30.c:932:13: note: each undeclared identifier is reported only once for each function it appears in
sound/soc/codecs/cs53l30.c:939:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(cs53l30->reset_gpio, 1);
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is powered down whilst a compressed stream is being processed
we should treat this as a fatal error, clearly the stream is no longer
valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter a fatal error on the compressed stream call the new
snd_compr_stop_error to shutdown the stream and allow the core to
inform user-space that the stream is no longer valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OUT4L and OUT4R widgets are not registered PRE_PMU or POST_PMD
events, as such the manual speaker enable on wm5102 does not actually
ever run. Furthermore since the issue actually only affected rev B of
the silicon which never shipped in volume, simply remove the work around
from the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio trace firmware on wm5102 only supports 4 channels correct
the DAI driver structure to reflect this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
