When changing the scan rate as part of runtime-resume process we may lose
some of the events, because:
1) for gen3 trackpads, the driver must msleep() some time to ensure that
the device is ready to accept next command;
2) for gen5 and later trackpads, the queue dumping function will simply
ignore the events when waiting for the set power mode command response.
The solution is to keep polling and report those valid events when the set
power mode command is in progress.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A dependency on ARCH_SHMOBILE seems to be the best option for sh_keysc:
* For Super H based SoCs: sh_keysc is used on SH_MIGOR, SH_ECOVEC, SH_KFR2R09,
SH_7722_SOLUTION_ENGINE, and SH_7724_SOLUTION_ENGINE, which depend on
either CPU_SUBTYPE_SH7722 or CPU_SUBTYPE_SH7724, and both select
ARCH_SHMOBILE.
* For ARM Based SoCs: Since the removal of legacy (non-multiplatform) support
this driver has not been used by any Renesas ARM based SoCs. The Renesas
ARM based SoCs currently select ARCH_SHMOBILE, however, it is planned
that this will no longer be the case.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for retrieving device resolution (pixels per mm) from firmware
and using it when setting up input device.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit e4b88e1989
"Input: stmpe-ts - enforce device tree only mode"
removed platform data but accidentally stripped away useful
kerneldoc, so reintroduce it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The SNVS power key driver has suspend/resume functions that
are accessed using SIMPLE_DEV_PM_OPS, which hide the reference
when CONFIG_PM_SLEEP is not set, resulting in a warning about
unused functions:
drivers/input/keyboard/snvs_pwrkey.c:183:12: error: 'imx_snvs_pwrkey_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/snvs_pwrkey.c:194:12: error: 'imx_snvs_pwrkey_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The spear keyboard driver uses #ifdef CONFIG_PM to hide its
power management functions, but then uses references from
SIMPLE_DEV_PM_OPS that are only present if both CONFIG_PM
and CONFIG_PM_SLEEP are set, resulting in a warning about unused
functions:
drivers/input/keyboard/spear-keyboard.c:292:12: error: 'spear_kbd_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/spear-keyboard.c:345:12: error: 'spear_kbd_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead uses a __maybe_unused
annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ACPI binding to the goldfish events driver.
Signed-off-by: Jason Hu <jia-cheng.hu@intel.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is an input driver for MELFAS MIP4 Touchscreen devices, such as
MMS400, MMS500, MCS8000, MIT200, MIT300, MIT400, MFS10. All devices
implementing MIP4 protocol (MELFAS Interface Protocol Version 4) should
be supported by this driver.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced or relaxed symbols TOUCHSCREEN_GOODIX and
TOUCHSCREEN_COLIBRI_VF50.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Driver for the BYD BTP10463 touchpad, found in PC Specialist `Lafite'
laptops. This patch sends the magic command sequence which causes the
touchpad to stream intellimouse-style packets.
Gestures are detected inside the touchpad, and exposed as special
values in the Z component of each packet - absolute coordinates are
not supported, even in the Windows driver. At present, this supports
two-finger vertical and horizontal scrolling, and provides the
framework to expose the other gestures it can recognize.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since we removed support for calling an init() callback from
the platform data, introduce a function which initializes
the chip by performing a hard reset, using the reset gpio
defined in the device properties.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop support for platform data passed via a C-structure and switch to
device properties instead, which should make the driver compatible
with all platforms: OF, ACPI and static boards. Static boards should
use property sets to communicate device parameters to the driver.
Signed-off-by: Oreste Salerno <oreste.salerno@tomtom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support to disable buttons from DT via status property if given button
is not supported on given platforms. This will help re-using existing dtsi
files across multiple platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allow specifying name if input device via device tree property. This helps
userspace code to get name and perform proper event to key mapping in some
cases (for example, on Android).
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bring in update to xpad driver improves support of Xbox One and wireless
controllers and fixes handling of concurrent requests to force feedback
and LEDs.
Apparently the Covert Forces ID is not Covert Forces pad exclusive, but
rather denotes a new firmware version that can be found on all new
controllers and can be also updated on old hardware using Windows 10.
see: https://github.com/paroj/xpad/issues/19
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Both T100 and T9 handle range and orientation in a similar fashion.
Reduce duplication between the two implementations.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As of e0361b7017 ("Input: wacom_w8001 - split the touch and pen devices
into two devices") the touch events aren't multiplexed over the same device
anymore, the use of ABS_MT_TOOL_TYPE is superfluous. And even before then
it only ever sent MT_TOOL_TYPE_FINGER anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 4ea14a53d8 ("Input: gpio-keys - report
error when disabling unsupported key") tried let user know that they
attempted to disable an unsupported key, unfortunately the check is wrong
as it believes that all codes are invalid. Fix it by ensuring that keys
that we try to disable are subset of keys (or switches) that device
reports.
Fixes: 4ea14a53d8 ("Input: gpio-keys - report error when disabling unsupported key")
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit da1f026b53 ("Keyboard: omap-keypad:
use matrix_keypad.h") switched the driver to use matrix keypad
infrastructure, which made array of keycodes to be unsigned short, and
caused the test for negativity never trigger. This leads to the following
static checker warning:
drivers/input/keyboard/omap-keypad.c:158 omap_kp_tasklet()
warn: 'keycodes[]' is never negative.
Given that we did not care about this check for a few years already let's
simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove write to REG_IRQCLR and REG_IRQWAKEUP in interrupt handler for
IRQENB_HW_PEN as the resume handler should and does clear REG_IRQWAKEUP.
IRQENB_HW_PEN bit is set in irqclr so that all interrupts get cleared
later so let IRQENB_HW_PEN be cleared by that.
Without this patch wakeup events from TSC_ADC do not work because pending
interrupts in TSC_ADC were causing HW_PEN interrupt, needed for wake from
suspend modes, to get disabled immediately by IRQ handler after being
enabled and preventing wake from happening.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It feels like we should set the tasklet data before enabling it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because of the wrong condition we'd never retry firmware update.
Acked-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch moves v3 pinnacle code for trackstick detection from
alps_hw_init_v3() to alps_set_protocol() so ALPS_DUALPOINT flag can be
cleared before registering trackstick input device in kernel.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds detection of trackstick for v7 protocol devices. Code in
this patch is used in official Dell touchpad linux drivers for Dell models:
Dell Latitude E5250/5250, E5450/5450, E5550/5550
Detection code and base reg for alps v3 rushmore and v7 devices is exacly
same.
Also user in bug https://bugzilla.kernel.org/show_bug.cgi?id=94801 reported
that Toshiba Sattellite Z30-A-1DG has only alps v7 touchpad device without
trackstick and kernel reports to userspace also redundant trackstick
device.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When lighting up the segment identifying wireless controller, Instead of
sending command directly to the controller, let's do it via LED API (usinf
led_set_brightness) so that LED object state is in sync with controller
state and we'll light up the correct segment on resume as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq_out urb is dead after suspend/ resume on my x360 wr pad. (also
reproduced by Zachary Lund [0]) Work around this by implementing
suspend, resume, and reset_resume callbacks and properly shutting down
URBs on suspend and restarting them on resume.
[0]: https://github.com/paroj/xpad/issues/6
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There's apparently a serial number woven into both input and output
packets; neglecting to specify a valid serial number causes the controller
to ignore the rumble packets.
The scale of the rumble was also apparently halved in the packets.
The initialization packet had to be changed to allow force feedback to
work.
see https://github.com/paroj/xpad/issues/7 for details.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Track the status of the irq_out URB to prevent submission iof new requests
while current one is active. Failure to do so results in the "URB submitted
while active" warning/stack trace.
Store pending brightness and FF effect in the driver structure and replace
it with the latest requests until the device is ready to process next
request. Alternate serving LED vs FF requests to make sure one does not
starve another. See [1] for discussion. Inspired by patch of Sarah Bessmer
[2].
[1]: http://www.spinics.net/lists/linux-input/msg40708.html
[2]: http://www.spinics.net/lists/linux-input/msg31450.html
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bma150_cfg structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We didn't check input_allocate_device() for failures so it could lead to
a NULL deref.
Fixes: 6b0f8f9c52 ('Input: add eGalaxTouch serial touchscreen driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the user can set ff_effects_max to zero with the EV_FF bit (and
the FF_GAIN and/or FF_AUTOCENTER bits) set, in this case the uninitialized
methods ff->set_gain and/or ff->set_autocenter can be dereferenced,
resulting in a kernel oops.
Check in uinput_create_device() and print a helpful message and return
-EINVAL in case the check fails.
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rework the uinput ABS validation to check passed absinfo data immediately,
but do ABS initialization as last step in UI_DEV_CREATE. The behavior
observed by user-space is not changed, as ABS initialization was never
checked for errors.
With this in place, the order of device initialization and abs
configuration is no longer fixed. Userspace can initialize the device and
afterwards set absinfo just fine.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds two new ioctls, UINPUT_DEV_SETUP and UI_ABS_SETUP, that replaces
the old device setup method (by write()'ing "struct uinput_user_dev" to the
node). The old method is not easily extendable and requires huge payloads.
Furthermore, overloading write() without properly versioned objects is
error-prone.
Therefore, we introduce two new ioctls to replace the old method. These
ioctls support all features of the old method, plus a "resolution" field
for absinfo. Furthermore, it's properly forward-compatible to new ABS codes
and a growing "struct input_absinfo" structure.
UI_ABS_SETUP also allows user-space to skip unknown axes if not set. There
is no need to copy the whole array temporarily into the kernel, but instead
the caller issues several ioctl where we copy each value manually.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix touchscreen driver uses a "rotated_screen" flag for
systems on which the touchscreen is mounted rotated by 180
degrees with respect to the display. With the addition of
support for the dt properties "touchscreen-inverted-x" and
"touchscreen-inverted-y", a separate "rotated_screen" flag
is not necessary anymore. This patch replaces it by setting
the inverted_x and inverted_y flags instead.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
- touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: Karsten Merker <merker@debian.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement suspend/resume for goodix driver.
The suspend and resume process uses the gpio pins. If the device ACPI/DT
information does not declare gpio pins, suspend/resume will not be
available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel trees for
various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).
The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).
Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.
Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes Logitech PS2++ protocol implementation consistent with
the naming in other protocols. Also mark the stub as "static inline"
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PS/2 protocol is slow, and using it with pass-through port (where we
encapsulate PS/2 into PS/2) is slower yet so it takes quite a bit of time
to do full protocol discovery for device attached to a pass-through port.
However, so far we have not see anything but trackpoints or basic PS/2
mice on pass-through ports, so let's limit protocols that we probe there
to Trackpoint, IntelliMouse Explorer, IntelliMouse, and bare PS/2 protocol,
and avoid other extended protocols, such as Synaptics, ALPS, etc.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
