Now that vfio_pci has been split into two source modules, one focusing on
the "struct pci_driver" (vfio_pci.c) and a toolbox library of code
(vfio_pci_core.c), complete the split and move them into two different
kernel modules.
As before vfio_pci.ko continues to present the same interface under sysfs
and this change will have no functional impact.
Splitting into another module and adding exports allows creating new HW
specific VFIO PCI drivers that can implement device specific
functionality, such as VFIO migration interfaces or specialized device
requirements.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-14-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Split the vfio_pci driver into two logical parts, the 'struct
pci_driver' (vfio_pci.c) which implements "Generic VFIO support for any
PCI device" and a library of code (vfio_pci_core.c) that helps
implementing a struct vfio_device on top of a PCI device.
vfio_pci.ko continues to present the same interface under sysfs and this
change should have no functional impact.
Following patches will turn vfio_pci and vfio_pci_core into a separate
module.
This is a preparation for allowing another module to provide the
pci_driver and allow that module to customize how VFIO is setup, inject
its own operations, and easily extend vendor specific functionality.
At this point the vfio_pci_core still contains a lot of vfio_pci
functionality mixed into it. Following patches will move more of the
large scale items out, but another cleanup series will be needed to get
everything.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-7-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is a preparation patch for separating the vfio_pci driver to a
subsystem driver and a generic pci driver. This patch doesn't change any
logic.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-2-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This driver never had any open userspace (which for VFIO would include
VM kernel drivers) that use it, and thus should never have been added
by our normal userspace ABI rules.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20210326061311.1497642-2-hch@lst.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case we're running on s390 system always expose the capabilities for
configuration of zPCI devices. In case we're running on different
platform, continue as usual.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Define a new configuration entry VFIO_PCI_ZDEV for VFIO/PCI.
When this s390-only feature is configured we add capabilities to the
VFIO_DEVICE_GET_INFO ioctl that describe features of the associated
zPCI device and its underlying hardware.
This patch is based on work previously done by Pierre Morel.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POWER9 Witherspoon machines come with 4 or 6 V100 GPUs which are not
pluggable PCIe devices but still have PCIe links which are used
for config space and MMIO. In addition to that the GPUs have 6 NVLinks
which are connected to other GPUs and the POWER9 CPU. POWER9 chips
have a special unit on a die called an NPU which is an NVLink2 host bus
adapter with p2p connections to 2 to 3 GPUs, 3 or 2 NVLinks to each.
These systems also support ATS (address translation services) which is
a part of the NVLink2 protocol. Such GPUs also share on-board RAM
(16GB or 32GB) to the system via the same NVLink2 so a CPU has
cache-coherent access to a GPU RAM.
This exports GPU RAM to the userspace as a new VFIO device region. This
preregisters the new memory as device memory as it might be used for DMA.
This inserts pfns from the fault handler as the GPU memory is not onlined
until the vendor driver is loaded and trained the NVLinks so doing this
earlier causes low level errors which we fence in the firmware so
it does not hurt the host system but still better be avoided; for the same
reason this does not map GPU RAM into the host kernel (usual thing for
emulated access otherwise).
This exports an ATSD (Address Translation Shootdown) register of NPU which
allows TLB invalidations inside GPU for an operating system. The register
conveniently occupies a single 64k page. It is also presented to
the userspace as a new VFIO device region. One NPU has 8 ATSD registers,
each of them can be used for TLB invalidation in a GPU linked to this NPU.
This allocates one ATSD register per an NVLink bridge allowing passing
up to 6 registers. Due to the host firmware bug (just recently fixed),
only 1 ATSD register per NPU was actually advertised to the host system
so this passes that alone register via the first NVLink bridge device in
the group which is still enough as QEMU collects them all back and
presents to the guest via vPHB to mimic the emulated NPU PHB on the host.
In order to provide the userspace with the information about GPU-to-NVLink
connections, this exports an additional capability called "tgt"
(which is an abbreviated host system bus address). The "tgt" property
tells the GPU its own system address and allows the guest driver to
conglomerate the routing information so each GPU knows how to get directly
to the other GPUs.
For ATS to work, the nest MMU (an NVIDIA block in a P9 CPU) needs to
know LPID (a logical partition ID or a KVM guest hardware ID in other
words) and PID (a memory context ID of a userspace process, not to be
confused with a linux pid). This assigns a GPU to LPID in the NPU and
this is why this adds a listener for KVM on an IOMMU group. A PID comes
via NVLink from a GPU and NPU uses a PID wildcard to pass it through.
This requires coherent memory and ATSD to be available on the host as
the GPU vendor only supports configurations with both features enabled
and other configurations are known not to work. Because of this and
because of the ways the features are advertised to the host system
(which is a device tree with very platform specific properties),
this requires enabled POWERNV platform.
The V100 GPUs do not advertise any of these capabilities via the config
space and there are more than just one device ID so this relies on
the platform to tell whether these GPUs have special abilities such as
NVLinks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the first consumer of vfio device specific resource support,
providing read-only access to the OpRegion for Intel graphics devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add PCI device support for VFIO. PCI devices expose regions
for accessing config space, I/O port space, and MMIO areas
of the device. PCI config access is virtualized in the kernel,
allowing us to ensure the integrity of the system, by preventing
various accesses while reducing duplicate support across various
userspace drivers. I/O port supports read/write access while
MMIO also supports mmap of sufficiently sized regions. Support
for INTx, MSI, and MSI-X interrupts are provided using eventfds to
userspace.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
