In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.
Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.
This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is modeled after one by Scott Peterson for i40e.
Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.
Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.
Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the local variable since it's only used once. Instead, use it
directly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are some places where the scope of a variable can
be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.
The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.
Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.
To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.
In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.
For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.
Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.
This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.
It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.
Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.
Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.
With this change, E810 devices should be able to perform basic PTP
functionality.
Future changes will extend the support to cover the E822-based devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.
Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.
The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.
If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is
PHC - (lower_32_bits(PHC) - timestamp)
If the Rx timestamp was captured after the PHC time, then the real
timestamp is
PHC + (timestamp - lower_32_bits(PHC))
These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.
In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.
Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.
Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.
To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.
Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.
With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change link misconfiguration message since the configuration
could be intended by the user.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once a netdev is registered, the corresponding network interface can
be immediately used by userspace utilities (like say NetworkManager).
This can be problematic if the driver technically isn't fully up yet.
Move netdev registration to the end of probe, as by this time the
driver data structures and device will be initialized as expected.
However, delaying netdev registration causes a failure in the aRFS flow
where netdev->reg_state == NETREG_REGISTERED condition is checked. It's
not clear why this check was added to begin with, so remove it.
Local testing didn't indicate any issues with this change.
The state bit check in ice_open was put in as a stop-gap measure to
prevent a premature interface up operation. This is no longer needed,
so remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.
Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open
To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An incorrect NVM update procedure can result in the driver failing probe.
In this case, the recommended resolution method is to update the NVM
using the right procedure. However, if the driver fails probe, the user
will not be able to update the NVM. So do not fail probe on link/PHY
errors.
Fixes: 1a3571b593 ("ice: restore PHY settings on media insertion")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
dev_validate_mtu checks that mtu value specified by user is not less
than min mtu and not greater than max allowed mtu. It is being done
before calling the ndo_change_mtu exposed by driver, so remove these
redundant checks in ice_change_mtu.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if the driver is unable to get all the MSI-X vectors it wants, it
falls back to the minimum configuration which equates to a single Tx/Rx
traffic queue pair. Instead of using the minimum configuration, if given
more vectors than the minimum, utilize those vectors for additional traffic
queues after accounting for other interrupts.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
This message indicates an error on close, not open.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
