Fix compiler warning found in the pinctrl-nomadik platform driver. GCC
message is as such:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:1169:12: warning: cast from
pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-9-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix compiler warning found in the pinctrl-nomadik platform driver. GCC
message is as such:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:855:21: warning:
format ‘%u’ expects argument of type ‘unsigned int’, but argument 5
has type ‘size_t {aka const long unsigned int}’ [-Wformat=]
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-8-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PINCTRL_NOMADIK, PINCTRL_STN8815 and PINCTRL_DB8500 depend on ARCH_U8500
or ARCH_NOMADIK. Add COMPILE_TEST as an option to allow test building
the driver.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-7-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously, drivers/pinctrl/nomadik/pinctrl-nomadik.c registered two
platform drivers: pinctrl & GPIO. Move the GPIO aspect to the
drivers/gpio/ folder, as would be expected.
Both drivers are intertwined for a reason; pinctrl requires access to
GPIO registers for pinmuxing, pull-disable, disabling interrupts while
setting the muxing and wakeup control. Information sharing is done
through a shared array containing GPIO chips and a few helper
functions. That shared array is not touched from gpio-nomadik when
CONFIG_PINCTRL_NOMADIK is not defined.
Make no change to the code that moved into gpio-nomadik; there should be
no behavior change following. A few functions are shared and header
comments are added. Checkpatch warnings are addressed. NUM_BANKS is
renamed to NMK_MAX_BANKS.
It is supported to compile gpio-nomadik without pinctrl-nomadik. The
opposite is not true.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-6-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously, the statement looked like:
slpm[x] &= ~BIT(g->grp.pins[i]);
Where:
- slpm is a unsigned int pointer;
- g->grp.pins[i] is a pin number. It can grow to more than 32.
The expected shift amount is a pin bank offset.
This bug does not occur on every group or pin: the altsetting must be
NMK_GPIO_ALT_C and the pin must be 32 or above. It might have occured.
For example, in pinctrl-nomadik-db8500.c, pin group i2c3_c_2 has the
right altsetting and pins 229 and 230.
Fixes: dbfe8ca259 ("pinctrl/nomadik: implement pin multiplexing")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-5-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the R-Car V4M (R8A779H0) SoC,
- Add support for suspend/resume on the RZ/G2L family,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZdh+5gAKCRCKwlD9ZEnx
cKiIAP9/dNg+l+cgCuI24EKaIehYnjq54clsWycHBV8i41brPgEAutwuYNMG++Vd
B/iDXOihVSvOhjpQluQMtoYaUBmOCQc=
=N37y
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v6.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.9 (take two)
- Add support for the R-Car V4M (R8A779H0) SoC,
- Add support for suspend/resume on the RZ/G2L family,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The conversion to DEFINE_NOIRQ_DEV_PM_OPS() lost the ability of the
compiler to optimize away the struct dev_pm_ops object when it is not
needed.
Fix this by replacing the use of pm_sleep_ptr() by a custom wrapper.
Fixes: 727eb02eb7 ("pinctrl: renesas: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/6238a78e32fa21f0c795406b6cba7bce7af92577.1708513940.git.geert+renesas@glider.be
pinctrl-rzg2l driver is used on RZ/G3S which support deep sleep states
where power to most of the SoC components is turned off.
For this add suspend/resume support. This involves saving and restoring
configured registers along with disabling clock in case there is no pin
configured as wakeup sources.
To save/restore registers 2 caches were allocated: one for GPIO pins and
one for dedicated pins.
On suspend path the pin controller registers are saved and if none of the
pins are configured as wakeup sources the pinctrl clock is disabled.
Otherwise it remains on.
On resume path the configuration is done as follows:
1/ setup PFCs by writing to registers on pin based accesses
2/ setup GPIOs by writing to registers on port based accesses and
following configuration steps specified in hardware manual
3/ setup dedicated pins by writing to registers on port based accesses
4/ setup interrupts.
Because interrupt signals are routed to IA55 interrupt controller and
IA55 interrupt controller resumes before pin controller, patch restores
also the configured interrupts just after pin settings are restored to
avoid invalid interrupts while resuming.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240215124112.2259103-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinctrl-rzg2l driver accesses gpio_chip.irq, which is available only
if CONFIG_GPIOLIB_IRQCHIP=y, and uses APIs that are defined only if
CONFIG_IRQ_DOMAIN_HIERARCHY=y (irq_chip_*_parent() APIs).
On ARCH_RZG2L, CONFIG_IRQ_DOMAIN_HIERARCHY is selected anyway, e.g. by
CONFIG_ARM_GIC_V3, but CONFIG_GPIOLIB_IRQCHIP is not (it is on R-Car).
Make this explicit at the driver level for a clearer view of the
dependencies.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240215124112.2259103-2-claudiu.beznea.uj@bp.renesas.com
[geert: select GPIOLIB_IRQCHIP, too]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently on irq_disable(), we are disabling gpio interrupt enable(ISEL).
That means the pin is just gpio input and not gpio input interrupt any
more. So, move configuring ISEL in rzg2l_gpio_child_to_parent_hwirq()/
rzg2l_gpio_irq_domain_free() so that the pin will be gpioint always even
during irq_disable().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240206135318.165426-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Configure GPIO interrupt as input mode. Also if the bootloader sets
gpio interrupt pin as function, override it as gpio.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240206135115.151218-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The driver for stm32mp257 is missing the suspend callback in
struct dev_pm_ops.
Add the callback, using the common stm32_pinctrl_suspend()
function.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: 619f8ca4a7 ("pinctrl: stm32: add stm32mp257 pinctrl support")
Link: https://lore.kernel.org/r/20240207104604.174843-1-antonio.borneo@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add pin groups for SCIF_CLK2 on R-Car V4H,
- Add support for port pins P19 to P28 on RZ/Five,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZcZV0wAKCRCKwlD9ZEnx
cAQ6AP9RPb5CW91132jjfoF/+dzAyEZj2YR8ndjrzN2QzOn4tQEAlfEOlavoTikB
oXQsRHGaeV8HQr02OEZgNJWYDXQMrAY=
=cnIJ
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.9
- Add pin groups for SCIF_CLK2 on R-Car V4H,
- Add support for port pins P19 to P28 on RZ/Five,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPINTEN register contains information about GPIOs with enabled
interrupts no need to check other GPIOs for changes.
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Link: https://lore.kernel.org/r/20240201141406.32484-2-arturas.moskvinas@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MT8192 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: d32f38f2a8 ("pinctrl: mediatek: Add pinctrl driver for mt8192")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240131071910.3950450-2-wenst@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MT8186 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: 8b483bda1e ("pinctrl: add pinctrl driver on mt8186")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240131071910.3950450-1-wenst@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing port pins P19 to P28 for RZ/Five SoC. These additional
pins provide expanded capabilities and are exclusive to the RZ/Five SoC.
Couple of port pins have different configuration and are not identical for
the complete port so introduce struct rzg2l_variable_pin_cfg to handle
such cases and introduce the PIN_CFG_VARIABLE macro. The actual pin config
is then assigned in rzg2l_pinctrl_get_variable_pin_cfg().
Add an additional check in rzg2l_gpio_get_gpioint() to only allow GPIO pins
which support interrupt facility.
While at define RZG2L_GPIO_PORT_PACK() using RZG2L_GPIO_PORT_SPARSE_PACK().
Update the gpio-ranges property in the RZ/Five SoC DTSI, as it must
match the driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Link: https://lore.kernel.org/r/20240129135556.63466-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently we assume all the port pins are sequential ie always PX_0 to
PX_n (n=1..7) exist, but on RZ/Five SoC we have additional pins P19_1 to
P28_5 which have holes in them, for example only one pin on port19 is
available and that is P19_1 and not P19_0. So to handle such cases
include pinmap for each port which would indicate the pin availability
on each port. As the pincount can be calculated based on pinmap drop this
from RZG2L_GPIO_PORT_PACK() macro.
Previously we had a max of 7 pins on each port but on RZ/Five Port-20
has 8 pins, so move the single pin configuration to BIT(63).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If the number of provided enum IDs in a variable width config register
description does not match the expected number, the checker uses the
expected number for validating the individual enum IDs.
However, this may cause out-of-bounds accesses on the array holding the
enum IDs, leading to bogus enum_id conflict warnings. Worse, if the bug
is an incorrect bit field description (e.g. accidentally using "12"
instead of "-12" for a reserved field), thousands of warnings may be
printed, overflowing the kernel log buffer.
Fix this by limiting the enum ID check to the number of provided enum
IDs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c7385f44f2faebb8856bcbb4e908d846fc1531fb.1705930809.git.geert+renesas@glider.be
Commit d3aaa7203a ("pinctrl: renesas: rzg2l: Add pin configuration
support for pinmux groups") introduced the possibility to parse pin
configuration for pinmux groups. It did that by calling
rzg2l_map_add_config() at the end of rzg2l_dt_subnode_to_map() and
jumping to the remove_group label in case rzg2l_map_add_config() failed.
But if that happens, the mutex will already be unlocked, thus this it will
lead to double mutex unlock operation. To fix this move the
rzg2l_map_add_config() call just after all the name argument is ready and
before the mutex is locked. There is no harm in doing this, as this only
parses the data from device tree that will be further processed by
pinctrl core code.
Fixes: d3aaa7203a ("pinctrl: renesas: rzg2l: Add pin configuration support for pinmux groups")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/f8c3a3a0-7c48-4e40-8af0-ed4e9d9b049f@moroto.mountain
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240115153453.99226-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use str_high_low() rather than open coding.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240129153138.3221604-3-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove some pointless inline declarations, no reason not to let the
compiler decide.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240129153138.3221604-2-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixup a couple of incorrect header includes.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240129153138.3221604-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific devm_kcalloc() function instead of the
argument size * count in the devm_kzalloc() function.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240119181909.7079-1-erick.archer@gmx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240117145547.3354242-1-jean.thomas@wifirst.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add uart1_3 (pins 26, 27) group to the pinctrl driver for the
MediaTek MT7981 SoC.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240117124234.3137050-1-jean.thomas@wifirst.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix kernel-doc warnings for enum (anonymous): the enum values are not
documented, so don't indicate that the comment contains kernel-doc
notation.
pinctrl-mt7986.c:68: warning: Enum value 'GPIO_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_RT_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_RB_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_LT_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_LB_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_TR_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_TL_BASE' not described in enum '(anonymous)'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312110210.x3vxq42A-lkp@intel.com/
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <linux-gpio@vger.kernel.org>
Cc: Sean Wang <sean.wang@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <linux-mediatek@lists.infradead.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lore.kernel.org/r/20240111045126.13768-1-rdunlap@infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return pinctrl_gpio_direction_output() in order to transfer the error
if it fails.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240103085058.3771653-1-nichen@iscas.ac.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A new PINCTRL_GROUP_DESC() infrastructure macro is added and
used in different drivers, generic group description struct
group_desc is now used all over the place.
New drivers:
- New driver for the Texas Instruments TPS6494 Power Management IC.
- New driver for the Lantic PEF2256 framer pin multiplexer.
This IC has some pins that can be reconfigured in different
ways. The actual driver comes on an immutable branch with the
net WAN parts, the IC is some latest-and-greatest serial line
funnel for e.g. wireless access points.
- New subdriver for the Samsung Exynos Auto V920 pin controller,
used for automotive applications.
- New subdriver for the Samsung "GS101" SoC pin controller, this
is the Google "Tensor" SoC used in the Google Pixel 6.
- New subdriver for the Intel Meteor Point SoC pin controller.
- New subdriver for the Qualcomm SM8650 top level (TLMM) and LPASS pin
controllers.
- New subdriver for the Qualcomm X1E80100 top level (TLMM) pin
controller.
- New subdriver for the Qualcomm SM4450 top level (TLMM) pin
controller.
- The "single" pin controller now supports the Texas Instruments
J7200 SoC.
Improvements:
- Intel has created a new (Intel-)generic pin controller driver that
is now used by all contemporary Intel platforms.
- Intel is now also making use of some cleanup helpers.
- Enble 910 Ohm bias in the Intel Tangier driver.
- The Samsung driver now suppors irq_set_affinity() in it's IRQ chip
giving support for non wake up external gpio interrupts.
-----BEGIN PGP SIGNATURE-----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=kj/d
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"For this kernel cycle I managed an immutable branch for the PEF2256
WAN framer that has some pin control portions. It already landed in
your tree through the net pull request but here it is mentioned again.
The most interesting is perhaps the Samsung Exynos subdrivers for the
Tensor SoC used in Google Pixel 6 and the ExynosAuto subdriver for
automotive. Along with the earlier merged Tesla FSD subdriver it shows
some of the versatile uses of the Samsung Exynos silicon. It is also
used in the latest version of Axis Communications ARTPEC chips so it
is a very widely deployed SoC family.
We also have the Intel Meteor Lake SoC which I think is for laptops.
It's a pretty interesting chip with Xe graphics and integrated PCH.
Core changes:
- A new PINCTRL_GROUP_DESC() infrastructure macro is added and used
in different drivers, generic group description struct group_desc
is now used all over the place.
New drivers:
- New driver for the Texas Instruments TPS6494 Power Management IC.
- New driver for the Lantic PEF2256 framer pin multiplexer. This IC
has some pins that can be reconfigured in different ways. The
actual driver comes on an immutable branch with the net WAN parts,
the IC is some latest-and-greatest serial line funnel for e.g.
wireless access points.
- New subdriver for the Samsung Exynos Auto V920 pin controller, used
for automotive applications.
- New subdriver for the Samsung "GS101" SoC pin controller, this is
the Google "Tensor" SoC used in the Google Pixel 6.
- New subdriver for the Intel Meteor Point SoC pin controller.
- New subdriver for the Qualcomm SM8650 top level (TLMM) and LPASS
pin controllers.
- New subdriver for the Qualcomm X1E80100 top level (TLMM) pin
controller.
- New subdriver for the Qualcomm SM4450 top level (TLMM) pin
controller.
- The "single" pin controller now supports the Texas Instruments
J7200 SoC.
Improvements:
- Intel has created a new (Intel-)generic pin controller driver that
is now used by all contemporary Intel platforms.
- Intel is now also making use of some cleanup helpers.
- Enble 910 Ohm bias in the Intel Tangier driver.
- The Samsung driver now suppors irq_set_affinity() in it's IRQ chip
giving support for non wake up external gpio interrupts"
* tag 'pinctrl-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: samsung: constify iomem pointers
pinctrl: cy8c95x0: Cache muxed registers
dt-bindings: pinctrl: xilinx: Rename *gpio to *gpio-grp
pinctrl: qcom: lpass-lpi: remove duplicated include
dt-bindings: pinctrl: qcom: drop common properties and allow wakeup-parent
dt-bindings: pinctrl: qcom: drop common properties
dt-bindings: pinctrl: qcom,ipq5018-tlmm: use common TLMM bindings
dt-bindings: pinctrl: qcom,x1e80100-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sm8650-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sm8550-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sdx75-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sa8775p-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,qdu1000-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom: create common LPASS LPI schema
pinctrl: qcom: sm4450: dd SM4450 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM4450 pinctrl
dt-bindings: pinctrl: qcom,pmic-mpp: clean up example
pinctrl: intel: Add Intel Meteor Point pin controller and GPIO support
pinctrl: renesas: rzg2l: Add input enable to the Ethernet pins
pinctrl: renesas: rzg2l: Add output enable support
...
Core GPIOLIB:
- protect the global list of GPIO devices with a read-write semaphore as
it is rarely modified but can be traversed by multiple readers at once
- remove GPIO devices from the global list when they are *unregistered*
and not when they are *released* (which only happens when the last
reference is dropped) as this may lead to a successful lookup of an
unregistered device
- remove the unnecessary "extra_checks" switch
- rename functions that are called with a lock taken
- remove duplicate includes
Character device handling:
- use locking guards to reduce the code size
- allocate the big linereq structure using the more suitable kvzalloc()
- redulce the size of critical sections
- improve documentation
- move the debounce_period_us field out of struct gpio_desc
New drivers:
- Nuvoton NPCM SGPIO driver for BMC NPCM7xx/NPCM8xx
- Realtek DHC (Digital Home Center) SoC GPIO driver
Driver improvements:
- replace gpiochip_is_requested() with a safer alternative in the form of
gpiochip_dup_line_label() as the former returns a pointer to a string that
can be deleted
- implement the dbg_show() callback in gpio-sim
- improve the coding style for local variables by removing unnecessary tabs
- use generic device properties instead of OF variants in gpio-mmio
- use the preferred coding style for __free() in gpio-mockup
- reuse PM ops from the gpio-tangier in gpio-elkhartlake
- rework PM and use cleanup helpers in gpio-tangier
- fix the EIC configuration in gpio-pmic-eic-sprd
- remove the unneeded call to platform_set_drvdata() in gpio-sifive
- use generic GPIO helpers for driver callbacks in gpio-dwapb
- add clock support on certain pins of gpio-ixp4xx
- don't use the core-specific DEBUG_GPIO switch in drivers
- kerneldoc improvements
DT bindings:
- add bindings for the new Realtek and Nuvoton devices
- allow gpio-ranges in gpio-dwapb
- support GPIO hogs in gpio-rockchip
- describe the label property in gpio-zynqmp-modepin
Other:
- header cleanups
- forward declarations cleanups
-----BEGIN PGP SIGNATURE-----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=bcXn
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, an assortment of updates and cleanups to many
others, and first part of the big rework of the core GPIOLIB that's
currently underway.
Add to that some code shrink in the character device module and
updates to DT bindings and that's pretty much it.
Core GPIOLIB:
- protect the global list of GPIO devices with a read-write semaphore
as it is rarely modified but can be traversed by multiple readers
at once
- remove GPIO devices from the global list when they are
*unregistered* and not when they are *released* (which only happens
when the last reference is dropped) as this may lead to a
successful lookup of an unregistered device
- remove the unnecessary "extra_checks" switch
- rename functions that are called with a lock taken
- remove duplicate includes
Character device handling:
- use locking guards to reduce the code size
- allocate the big linereq structure using the more suitable
kvzalloc()
- redulce the size of critical sections
- improve documentation
- move the debounce_period_us field out of struct gpio_desc
New drivers:
- Nuvoton NPCM SGPIO driver for BMC NPCM7xx/NPCM8xx
- Realtek DHC (Digital Home Center) SoC GPIO driver
Driver improvements:
- replace gpiochip_is_requested() with a safer alternative in the
form of gpiochip_dup_line_label() as the former returns a pointer
to a string that can be deleted
- implement the dbg_show() callback in gpio-sim
- improve the coding style for local variables by removing
unnecessary tabs
- use generic device properties instead of OF variants in gpio-mmio
- use the preferred coding style for __free() in gpio-mockup
- reuse PM ops from the gpio-tangier in gpio-elkhartlake
- rework PM and use cleanup helpers in gpio-tangier
- fix the EIC configuration in gpio-pmic-eic-sprd
- remove the unneeded call to platform_set_drvdata() in gpio-sifive
- use generic GPIO helpers for driver callbacks in gpio-dwapb
- add clock support on certain pins of gpio-ixp4xx
- don't use the core-specific DEBUG_GPIO switch in drivers
- kerneldoc improvements
DT bindings:
- add bindings for the new Realtek and Nuvoton devices
- allow gpio-ranges in gpio-dwapb
- support GPIO hogs in gpio-rockchip
- describe the label property in gpio-zynqmp-modepin
Other:
- header cleanups
- forward declarations cleanups"
* tag 'gpio-updates-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (55 commits)
gpiolib: replace the GPIO device mutex with a read-write semaphore
gpiolib: remove the GPIO device from the list when it's unregistered
gpio: nuvoton: Add Nuvoton NPCM sgpio driver
dt-bindings: gpio: add NPCM sgpio driver bindings
gpio: rtd: Add support for Realtek DHC(Digital Home Center) RTD SoCs
dt-bindings: gpio: realtek: Add realtek,rtd-gpio
gpio: pmic-eic-sprd: Configure the bit corresponding to the EIC through offset
gpio: dwapb: Use generic request, free and set_config
gpio: sysfs: drop tabs from local variable declarations
gpiolib: drop tabs from local variable declarations
gpiolib: remove extra_checks
gpio: tps65219: don't use CONFIG_DEBUG_GPIO
gpiolib: cdev: replace locking wrappers for gpio_device with guards
gpiolib: cdev: replace locking wrappers for config_mutex with guards
gpiolib: cdev: allocate linereq using kvzalloc()
gpiolib: cdev: include overflow.h
gpiolib: cdev: reduce locking in gpio_desc_to_lineinfo()
gpiolib: cdev: improve documentation of get/set values
gpiolib: cdev: fully adopt guard() and scoped_guard()
gpiolib: remove debounce_period_us from struct gpio_desc
...
Constify few pointers to iomem, where the destination memory is not
modified, for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231223191902.22857-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trying to suspend to RAM on SAMA5D27 EVK leads to the following lockdep
warning:
============================================
WARNING: possible recursive locking detected
6.7.0-rc5-wt+ #532 Not tainted
--------------------------------------------
sh/92 is trying to acquire lock:
c3cf306c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
but task is already holding lock:
c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by sh/92:
#0: c3aa0258 (sb_writers#6){.+.+}-{0:0}, at: ksys_write+0xd8/0x178
#1: c4c2df44 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x138/0x284
#2: c32684a0 (kn->active){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x148/0x284
#3: c232b6d4 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x13c/0x4e8
#4: c387b088 (&dev->mutex){....}-{3:3}, at: __device_suspend+0x1e8/0x91c
#5: c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
stack backtrace:
CPU: 0 PID: 92 Comm: sh Not tainted 6.7.0-rc5-wt+ #532
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from __lock_acquire+0x19ec/0x3a0c
__lock_acquire from lock_acquire.part.0+0x124/0x2d0
lock_acquire.part.0 from _raw_spin_lock_irqsave+0x5c/0x78
_raw_spin_lock_irqsave from __irq_get_desc_lock+0xe8/0x100
__irq_get_desc_lock from irq_set_irq_wake+0xa8/0x204
irq_set_irq_wake from atmel_gpio_irq_set_wake+0x58/0xb4
atmel_gpio_irq_set_wake from irq_set_irq_wake+0x100/0x204
irq_set_irq_wake from gpio_keys_suspend+0xec/0x2b8
gpio_keys_suspend from dpm_run_callback+0xe4/0x248
dpm_run_callback from __device_suspend+0x234/0x91c
__device_suspend from dpm_suspend+0x224/0x43c
dpm_suspend from dpm_suspend_start+0x9c/0xa8
dpm_suspend_start from suspend_devices_and_enter+0x1e0/0xa84
suspend_devices_and_enter from pm_suspend+0x460/0x4e8
pm_suspend from state_store+0x78/0xe4
state_store from kernfs_fop_write_iter+0x1a0/0x284
kernfs_fop_write_iter from vfs_write+0x38c/0x6f4
vfs_write from ksys_write+0xd8/0x178
ksys_write from ret_fast_syscall+0x0/0x1c
Exception stack(0xc52b3fa8 to 0xc52b3ff0)
3fa0: 00000004 005a0ae8 00000001 005a0ae8 00000004 00000001
3fc0: 00000004 005a0ae8 00000001 00000004 00000004 b6c616c0 00000020 0059d190
3fe0: 00000004 b6c61678 aec5a041 aebf1a26
This warning is raised because pinctrl-at91-pio4 uses chained IRQ. Whenever
a wake up source configures an IRQ through irq_set_irq_wake, it will
lock the corresponding IRQ desc, and then call irq_set_irq_wake on "parent"
IRQ which will do the same on its own IRQ desc, but since those two locks
share the same class, lockdep reports this as an issue.
Fix lockdep false positive by setting a different class for parent and
children IRQ
Fixes: 776180848b ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Link: https://lore.kernel.org/r/20231215-lockdep_warning-v1-1-8137b2510ed5@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the port specific registers behind the PORTSEL mux aren't
cached in the regmap and thus the typical setup time for a single pin
on cy8c9560 is about 200msec on our system. The hotspot is the IRQ
(un)masking, which causes lots of R/W operations.
Introduce a separate regmap for muxed registers and helper functions
to use the newly introduced regmap for muxed register access under
the i2c lock.
With the new cache in place the typical pin setup time is reduced to
20msec, making it about 10 times faster. As a side effect the system
boot time is also reduced by 50%.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231219125350.4031370-1-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 1fa3df901f ("pinctrl: cy8c95x0: Remove custom ->set_config()")
removed support for PIN_CONFIG_INPUT_ENABLE and
PIN_CONFIG_OUTPUT.
Add the following options to restore functionality:
- PIN_CONFIG_INPUT_ENABLE
- PIN_CONFIG_OUTPUT_ENABLE
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20231219125120.4028862-2-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
remove the second #include <linux/seq_file.h>
Signed-off-by: Wang Jinchao <wangjinchao@xfusion.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/202312151810+0800-wangjinchao@xfusion.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for TLMM block found in SM4450 SoC.
Can Guo helped out in reviewing the driver.
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20231212094900.12615-3-quic_tengfan@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* New agnostic driver to support Lunar Lake and newer platforms
* New driver for Intel Meteor Point-S (PCH for Meteor Lake-S)
* Update drivers to use new PM helpers
* Use RAII for locking in a few drivers (Raag, Andy)
* Reduce locking scope in some functions (Raag)
* Miscellaneous cleanups (Raag)
The following is an automated git shortlog grouped by driver:
alderlake:
- Switch to use Intel pin control PM ops
baytrail:
- Simplify code with cleanup helpers
- Move default strength assignment to a switch-case
- Factor out byt_gpio_force_input_mode()
- Fix types of config value in byt_pin_config_set()
broxton:
- Switch to use Intel pin control PM ops
cannonlake:
- Switch to use Intel pin control PM ops
cedarfork:
- Switch to use Intel pin control PM ops
denverton:
- Switch to use Intel pin control PM ops
elkhartlake:
- Switch to use Intel pin control PM ops
emmitsburg:
- Switch to use Intel pin control PM ops
geminilake:
- Switch to use Intel pin control PM ops
icelake:
- Switch to use Intel pin control PM ops
intel:
- Add Intel Meteor Point pin controller and GPIO support
- use the correct _PM_OPS() export macro
- Add a generic Intel pin control platform driver
- Revert "Unexport intel_pinctrl_probe()"
- allow independent COMPILE_TEST
- Refactor intel_pinctrl_get_soc_data()
- Move default strength assignment to a switch-case
- Make PM ops functions static
- Provide Intel pin control wide PM ops structure
jasperlake:
- Switch to use Intel pin control PM ops
lakefield:
- Switch to use Intel pin control PM ops
lewisburg:
- Switch to use Intel pin control PM ops
lynxpoint:
- Simplify code with cleanup helpers
meteorlake:
- Switch to use Intel pin control PM ops
sunrisepoint:
- Switch to use Intel pin control PM ops
tangier:
- simplify locking using cleanup helpers
- Move default strength assignment to a switch-case
- Enable 910 Ohm bias
tigerlake:
- Switch to use Intel pin control PM ops
-----BEGIN PGP SIGNATURE-----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=72T1
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v6.8-1
* New agnostic driver to support Lunar Lake and newer platforms
* New driver for Intel Meteor Point-S (PCH for Meteor Lake-S)
* Update drivers to use new PM helpers
* Use RAII for locking in a few drivers (Raag, Andy)
* Reduce locking scope in some functions (Raag)
* Miscellaneous cleanups (Raag)
The following is an automated git shortlog grouped by driver:
alderlake:
- Switch to use Intel pin control PM ops
baytrail:
- Simplify code with cleanup helpers
- Move default strength assignment to a switch-case
- Factor out byt_gpio_force_input_mode()
- Fix types of config value in byt_pin_config_set()
broxton:
- Switch to use Intel pin control PM ops
cannonlake:
- Switch to use Intel pin control PM ops
cedarfork:
- Switch to use Intel pin control PM ops
denverton:
- Switch to use Intel pin control PM ops
elkhartlake:
- Switch to use Intel pin control PM ops
emmitsburg:
- Switch to use Intel pin control PM ops
geminilake:
- Switch to use Intel pin control PM ops
icelake:
- Switch to use Intel pin control PM ops
intel:
- Add Intel Meteor Point pin controller and GPIO support
- use the correct _PM_OPS() export macro
- Add a generic Intel pin control platform driver
- Revert "Unexport intel_pinctrl_probe()"
- allow independent COMPILE_TEST
- Refactor intel_pinctrl_get_soc_data()
- Move default strength assignment to a switch-case
- Make PM ops functions static
- Provide Intel pin control wide PM ops structure
jasperlake:
- Switch to use Intel pin control PM ops
lakefield:
- Switch to use Intel pin control PM ops
lewisburg:
- Switch to use Intel pin control PM ops
lynxpoint:
- Simplify code with cleanup helpers
meteorlake:
- Switch to use Intel pin control PM ops
sunrisepoint:
- Switch to use Intel pin control PM ops
tangier:
- simplify locking using cleanup helpers
- Move default strength assignment to a switch-case
- Enable 910 Ohm bias
tigerlake:
- Switch to use Intel pin control PM ops
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1. New hardware: Add pin controllers for Samsung ExynosAutov920 and
Google Tensor GS101.
2. Few DT bindings cleanups: add specific compatibles for each device
using generic compatible as fallback. This affects only DTS, no
driver changes are needed.
3. Allow setting affinity on non wake-up external GPIO interrupts.
-----BEGIN PGP SIGNATURE-----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=hlN6
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-6.8' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v6.8
1. New hardware: Add pin controllers for Samsung ExynosAutov920 and
Google Tensor GS101.
2. Few DT bindings cleanups: add specific compatibles for each device
using generic compatible as fallback. This affects only DTS, no
driver changes are needed.
3. Allow setting affinity on non wake-up external GPIO interrupts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add pinmux groups, power source, and input/output enable support for
Ethernet pins on RZ/G2L SoCs,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZXxCWwAKCRCKwlD9ZEnx
cGH/APsEC7rILFNMeP4o25rQHbqf/xIx+6KBZIXjH+ia+4uFJwEAkljmLIupZ7BB
L3QlxtdIk87wvzh5ZLfL9g4IK+ig2gk=
=5+7i
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v6.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.8 (take two)
- Add pinmux groups, power source, and input/output enable support for
Ethernet pins on RZ/G2L SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver supports pinctrl/GPIO hardware found on Intel Meteor Point
(a Meteor Lake PCH) providing users a pinctrl and GPIO interfaces
including GPIO interrupts.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some of the RZ/G3S Ethernet pins (P1_0, P7_0) can be configured with
input enable. Enable this functionality for these pins.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-8-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some of the Ethernet pins on RZ/G3S (but also valid for RZ/G2L) need to
have the direction of the IO buffer set as output for Ethernet to work
properly. On RZ/G3S, these pins are P1_0/P7_0, P1_1/P7_1, and can have
the following Ethernet functions: TXC/TX_CLK or TX_CTL/TX_EN.
As the pins supporting output enable are SoC specific, and there is a
limited number of these pins (TXC/TX_CLK and/or TX_CTL/TX_EN), specify
output enable capable port limits in the platform-based configuration
data structure, to ensure proper validation.
The OEN support has been intantiated for RZ/G3S at the moment.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GPIO controller available on RZ/G3S (but also on RZ/G2L) supports
setting the power source for Ethernet pins. Based on the interface b/w
the Ethernet controller and the Ethernet PHY, and on board design, a
specific power source needs to be selected. The GPIO controller
supports 1.8V, 2.5V, and 3.3V power source selection for the Ethernet
pins. This can be selected though the ETHx_POC registers (x={0, 1}).
Adjust the driver to support this, and to do proper instantiation for
the RZ/G3S and RZ/G2L SoCs. On RZ/G2L only the get operation has been
tested at the moment.
While at it, as the power registers on RZ/G2L support access sizes of 8
bits, and these registers on RZ/G3S support access sizes of 8/16/32
bits, replace writel()/readl() on these registers with writeb()/readb().
This should allow us to use the same code on both SoCs w/o any issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On RZ/G3S different Ethernet pins need to be configured with different
settings (e.g. power-source needs to be set, RGMII TXC and TX_CTL pins
need output-enable). Adjust the driver to allow specifying pin
configuration for pinmux groups. With this, DT settings like the
following are taken into account by the driver:
eth0_pins: eth0 {
tx_ctl {
pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>; /* ET0_TX_CTL */
power-source = <1800>;
output-enable;
drive-strength-microamp = <5200>;
};
};
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move arg and index in the main block of the function as they are used by
more than one case block of switch-case (3 out of 4 for arg, 2 out of 4
for index). In this way some lines of code are removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pinctrl data for ExynosAutov920 SoC.
It has a newly applied pinctrl register layer for ExynosAuto series.
Pinctrl data for ExynosAutoV920 SoC.
- GPA0,GPA1 (10): External wake up interrupt
- GPQ0 (2): SPMI (PMIC I/F)
- GPB0,GPB1,GPB2,GPB3,GPB4,GPB5,GPB6 (47): I2S Audio
- GPH0,GPH1,GPH2,GPH3,GPH4,GPH5,GPH6,GPH8 (49): PCIE, UFS, Ethernet
- GPG0,GPG1,GPG2,GPG3,GPG4,GPG5 (29): General purpose
- GPP0,GPP1,GPP2,GPP3,GPP4,GPP5,GPP6,GPP7,GPP8,GPP9,GPP10 (77): USI
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-3-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
New ExynosAuto series GPIO have a different register structure.
In the existing Exynos series, EINT control register is enumerated after
a specific offset (e.g EXYNOS_GPIO_ECON_OFFSET, EXYNOS_GPIO_EMASK_OFFSET).
However, from ExynosAutov920 SoC, the register that controls EINT belongs
to each GPIO bank, and each GPIO bank has 0x1000 align.
This is a structure to protect the GPIO bank using S2MPU in VM environment,
and will only be applied in ExynosAuto series SoCs.
--------------------------------------------------------------
| Original Exynos | ExynosAuto |
|------------------------------------------------------------|
| 0x0 GPIO_CON | 0x0 GPIO_CON |
| 0x4 GPIO_DAT | 0x4 GPIO_DAT |
| 0x8 GPIO_PUD | 0x8 GPIO_PUD |
| 0xc GPIO_DRV | 0xc GPIO_DRV |
| 0x10 GPIO_CONPDN | 0x10 GPIO_CONPDN |
| 0x14 GPIO_PUDPDN | 0x14 GPIO_PUDPDN |
|----------------------------| 0x18 EINT_CON (per_bank) |
| ... | 0x1c EINT_FLTCON0 (per_bank) |
| ... | 0x20 EINT_FLTCON1 (per_bank) |
| ... | 0x24 EINT_MASK (per_bank) |
| ... | 0x28 EINT_PEND (per_bank) |
|----------------------------|-------------------------------|
| 0x700 EINT_CON (global) | ... |
| 0x800 EINT_FLTCON (global) | ... |
| 0x900 EINT_MASK (global) | ... |
| 0xa00 EINT_FEND (global) | ... |
--------------------------------------------------------------
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-2-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
-----BEGIN PGP SIGNATURE-----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=MQyi
-----END PGP SIGNATURE-----
Merge tag 'pef2256-framer' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Linus Walleij says:
====================
Immutable tag for the PEF2256 framer
* tag 'pef2256-framer' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
MAINTAINERS: Add the Lantiq PEF2256 driver entry
pinctrl: Add support for the Lantic PEF2256 pinmux
net: wan: framer: Add support for the Lantiq PEF2256 framer
dt-bindings: net: Add the Lantiq PEF2256 E1/T1/J1 framer
net: wan: Add framer framework support
====================
Link: https://lore.kernel.org/all/CACRpkdYT1J7noFUhObFgfA60XQAfL4rb=knEmWS__TKKtCMh7Q@mail.gmail.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Lantiq PEF2256 is a framer and line interface component designed to
fulfill all required interfacing between an analog E1/T1/J1 line and the
digital PCM system highway/H.100 bus.
This kind of component can be found in old telecommunication system.
It was used to digital transmission of many simultaneous telephone calls
by time-division multiplexing. Also using HDLC protocol, WAN networks
can be reached through the framer.
This pinmux support handles the pin muxing part (pins RP(A..D) and pins
XP(A..D)) of the PEF2256.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231128132534.258459-5-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the pin-controller found on the gs101 SoC used in
Pixel 6 phones.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-10-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
All drivers are converted to use embedded struct pingroup.
Remove unused members from struct group_desc.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-14-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct group_desc is a particular version of the struct pingroup
with associated opaque data. Start switching pin control core and
drivers to use it explicitly.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- provide a safer alternative to gpiochip_is_requested()
- convert all existing users
- remove gpiochip_is_requested()
-----BEGIN PGP SIGNATURE-----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=PlCm
-----END PGP SIGNATURE-----
Merge tag 'gpio-remove-gpiochip_is_requested-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: remove gpiochip_is_requested()
- provide a safer alternative to gpiochip_is_requested()
- convert all existing users
- remove gpiochip_is_requested()
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unclear why it's not a const unsigned int pointer from day 1.
Make the pins member const unsigned int pointer in struct group_desc.
Update necessary APIs.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are not going to change pins in the ->set_mux() callback. Mark
the local variable with a const qualifier. While at it, make it
also unsigned.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231204160033.1872569-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a pin isn't marked as a wake source processing any interrupts is
just going to destroy battery life. The APU may wake up from a hardware
sleep state to process the interrupt but not return control to the OS.
Mask interrupt for all non-wake source pins at suspend. They'll be
re-enabled at resume.
Reported-and-tested-by: Marcus Aram <marcus+oss@oxar.nl>
Reported-and-tested-by: Mark Herbert <mark.herbert42@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2812
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231203032431.30277-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
