For both capture and playback streams to work at the same time, only the
needed values from a register need to be updated. Also, clocks should be
enabled only when the first stream is started and stopped when there is no
running stream.
Fixes: b543e467d1 ("ASoC: atmel-i2s: add driver for the new Atmel I2S controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210618150741.401739-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S needs to have the same sample bits for both capture and playback
streams.
Fixes: b543e467d1 ("ASoC: atmel-i2s: add driver for the new Atmel I2S controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210618150741.401739-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I haven't touched these drivers in seven years, and none of the
patches sent to me these days affect code that I wrote. The
other maintainers are doing a very good job without me.
Signed-off-by: Timur Tabi <timur@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210620160135.28651-1-timur@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-sdca-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The code is slightly different from the other codecs since the
interrupt callback deals with the SDCA interrupts, leading to a much
larger section that's protected by the mutex. The SoundWire interrupt
scheme requires a read after clearing a status, it's not clear from
the specifications what would happen if SDCA interrupts are disabled
in the middle of the sequence, so the entire interrupt status
read/write is kept as is, even if in the end we discard the
information.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT5682-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The Fixes tag points to a 5.10 commit, there's no need to propagate
this change to earlier upstream versions.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 4a55000722 ('ASoC: codecs: rt*.c: remove useless pointer cast')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 501ef01339 ('ASoC: rt711: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 5f2df2a458 ('ASoC: rt700: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently export sdw_read() and sdw_write() but the sdw_update()
and sdw_update_no_pm() are currently available only to the bus
code. This was missed in an earlier contribution.
Export both functions so that codec drivers can perform
read-modify-write operations without duplicating the code.
Fixes: b04c975e65 ('soundwire: bus: use sdw_update_no_pm when initializing a device')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210614180815.153711-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is error message when defer probe happens:
fsl-spdif-dai 2dab0000.spdif: Unbalanced pm_runtime_enable!
Fix the error handler with pm_runtime_enable and add
fsl_spdif_remove() for pm_runtime_disable.
Fixes: 9cb2b3796e ("ASoC: fsl_spdif: Add pm runtime function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1623392318-26304-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SGTL5000 codec can be connected via audio-graph-card,
add the missing port: entry into the bindings.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210610150135.29905-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the fixes reverted as part of the UMN fallout was actually fine,
however rather than undoing the revert the process that handled all this
stuff resulted in a patch which attempted to add extra error checks
instead. Unfortunately this new change wasn't really based on a good
understanding of the subsystem APIs and bypassed the usual patch flow
without ensuring it was reviewed by people with subsystem knowledge and
was merged as a fix rather than during the merge window.
The effect of the new fix is to upgrade what were previously warnings on
static data in the code to hard errors on that data. If this actually
happens then it would break existing systems, if it doesn't happen then
the change has no effect so this was not a safe change to apply as a fix
to the release candidates. Since the new code has not been tested and
doesn't in practice improve error handling revert it instead, and also
drop the original revert since the original fix was fine. This takes
the driver back to what it was in -rc1.
Fixes: 5e70b8e22b ("ASoC: rt5645: add error checking to rt5645_probe function")
Fixes: 1e0ce84215 ("Revert "ASoC: rt5645: fix a NULL pointer dereference")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210608160713.21040-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only hangle rt711->regmap in rt711_sdca_io_init(), and
rt711->mbq_regmap is missing.
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SDW_SDCA_CTL() registers are used but are not set to readable.
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5682_DEVICE_ID is a volatile register, we can not read it in cache
only mode.
Fixes: 03f6fc6de9 ("ASoC: rt5682: Add the soundwire support")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device checking error should be a jump to pm_runtime_put_autosuspend()
as done before returning value.
Fixes: 867f8d18df ('ASoC: rt5682: fix getting the wrong device id when the suspend_stress_test')
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix clock stop prepare timeout issue (#2853).
The trigger of internal circuit which belong to
“SDCA preset stuffs” was not set correctly in previous driver,
which could block clock_stop_preparation state.
Add the correct register setting to fix it.
Fixes: 20d17057f0 ('ASoC: rt715-sdca: Add RT715 sdca vendor-specific driver')
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: d1ede0641b ('ASoC: rt715: add RT715 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers (was 'first_init')
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 20d17057f0 ('ASoC: rt715-sdca: Add RT715 sdca vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 320b8b0d13 ('ASoC: rt711: add rt711 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 7d2a5f9ae4 ('ASoC: rt700: add rt700 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 03f6fc6de9 ('ASoC: rt5682: Add the soundwire support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 2b719fd20f ('ASoC: rt1316: Add RT1316 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: a87a6653a2 ('ASoC: rt1308-sdw: add rt1308 SdW amplifier driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers.
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 56a5b7910e ('ASoC: codecs: max98373: add SoundWire support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS2562_TDM_CFG0_SAMPRATE_MASK starts at bit 1, not 0.
So all values need to be left shifted by 1.
Signed-off-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20210530203446.19022-1-richard@nod.at
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a fair amount of warnings when running 'make dtbs_check' with
amlogic,gx-sound-card.yaml.
Ex:
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:1: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:2: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0: [66, 0, 0] is too long
The reason is that the sound-dai phandle provided has cells, and in such
case the schema should use 'phandle-array' instead of 'phandle'.
Fixes: fd00366b8e ("ASoC: meson: gx: add sound card dt-binding documentation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210524093448.357140-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unfortunately the previous patch to fix issues using the AMD ACP bridge
has the side effect of breaking the dmic in other cases and needs to be
reverted.
Removing the changes while we revisit the fix and find something better.
Apologies for the churn.
Suggested-by: Gabriel Craciunescu <unix.or.die@gmail.com>
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210602171251.3243-1-markpearson@lenovo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
More laptops identified where the AMD ACP bridge needs to be blocked
or the microphone will not work when connected to HDMI.
Use DMI to block the microphone PCM device for these platforms.
Suggested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210531145502.6079-1-markpearson@lenovo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent changes to use common code to power up/down DSP cores also
removed the reset of the core state at suspend. It turns out this is
still needed. When the firmware state is reset to
SOF_FW_BOOT_NOT_STARTED, also enabled_cores should be reset, and
existing DSP drivers depend on this.
BugLink: https://github.com/thesofproject/linux/issues/2824
Fixes: 42077f08b3 ("ASoC: SOF: update dsp core power status in common APIs")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20210528144330.2551-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The power of "LDO2", "MICBIAS1" and "Mic Det Power" were powered off after
the DAPM widgets were added, and these powers were set by the JD settings
"RT5659_JD_HDA_HEADER" in the probe function. In the codec probe function,
these powers were ignored to prevent them controlled by DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Message-Id: <15fced51977b458798ca4eebf03dafb9@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check the return value of devm_kstrdup() in case of
Null-point-dereference.
Fixes: 45dd9943fc ("ASoC: core: remove artificial component and DAI name constraint")
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20210524024941.159952-1-wangkefeng.wang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Do not check the LBR_TOS MSR when setting up unrelated LBR MSRs as this
can cause malfunction when TOS is not supported.
- Allocate the LBR XSAVE buffers along with the DS buffers upfront because
allocating them when adding an event can deadlock.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmCqWZQTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoZe6D/9vKZRfmbdvOwfE0Z7dBil2dyBoqYHw
yTfnGs0pNpmj2mY7ZPig3gmXnryt4cwMcTtVJZFdmYJBBS28tqGeJb7eMIxtSqAu
aBChANXVOnbAS8vXe555nS/BVxEtfkIBgOLyYlD0hE4PIZpBbqTzhxj4daLTk4bg
h4hyIzDMBs+4tLupVhOahg6ZaHd97S61e7gBR9I5D7tHAUMo8Ea0ChQD5p2kDYI5
leKroBnjUFMP0o2DYPUR+6Zma50JQ29QK1u34q4mx0IhIdgqtNs8eZE/kYUu2FSZ
Nf4GG2ALzxWjXniqRPrXbkP/ScrwVdhg7ULOG34aNT1Jx04KaMSkav93gbOdozV9
IYvf99zwptD3g9W4yDveWjGrhEoxiARI4VUQJBnIbQP9rZ2YIRwOHIXwux1AxWQh
ok6CP94m16AWp0wbm9HRJS80MUv1zHPK5oW3B1vkchxHihkV4XdoP6vny03Z2FcC
elMgFquDxP4l5i3ao0Ryn4YaCAFc3MiWvw3x4YXpv9dCE6Al+iKdclkYPJgrYWYE
wUN8jdODfIyBIOI94GnwYl5rHIoS2fH8LSpP36gIX7DMKPh5y7184jUQWjHTN6PT
/D94us3m8Cvq+sfZrhGDHPY4BEaYeczTo6vbVoN4iBthElLYRkHp7lc7gcDpsU8B
dzHcwyMFQAnKLQ==
=7WGT
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Two perf fixes:
- Do not check the LBR_TOS MSR when setting up unrelated LBR MSRs as
this can cause malfunction when TOS is not supported
- Allocate the LBR XSAVE buffers along with the DS buffers upfront
because allocating them when adding an event can deadlock"
* tag 'perf-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/lbr: Remove cpuc->lbr_xsave allocation from atomic context
perf/x86: Avoid touching LBR_TOS MSR for Arch LBR
- Invoke the lockdep tracepoints in the correct place so the ordering
is correct again.
- Don't leave the mutex WAITER bit stale when the last waiter is dropping
out early due to a signal as that forces all subsequent lock operations
needlessly into the slowpath until it's cleaned up again.
-----BEGIN PGP SIGNATURE-----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=7vqW
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two locking fixes:
- Invoke the lockdep tracepoints in the correct place so the ordering
is correct again
- Don't leave the mutex WAITER bit stale when the last waiter is
dropping out early due to a signal as that forces all subsequent
lock operations needlessly into the slowpath until it's cleaned up
again"
* tag 'locking-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/mutex: clear MUTEX_FLAGS if wait_list is empty due to signal
locking/lockdep: Correct calling tracepoints
- Allocate interrupt descriptors correctly on Mainstone PXA when
SPARSE_IRQ is enabled; otherwise the interrupt association fails.
- Make the APPLE AIC chip driver depend on APPLE.
- Remove redundant error output on devm_ioremap_resource() failure.
-----BEGIN PGP SIGNATURE-----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=XjHi
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A few fixes for irqchip drivers:
- Allocate interrupt descriptors correctly on Mainstone PXA when
SPARSE_IRQ is enabled; otherwise the interrupt association fails
- Make the APPLE AIC chip driver depend on APPLE
- Remove redundant error output on devm_ioremap_resource() failure"
* tag 'irq-urgent-2021-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Remove redundant error printing
irqchip/apple-aic: APPLE_AIC should depend on ARCH_APPLE
ARM: PXA: Fix cplds irqdesc allocation when using legacy mode
of killing the machine and by using the accessors with the exact functionality
needed when accessing memory.
- Fix a confusion with Clang LTO compiler switches passed to the it
- Handle the case gracefully when VMGEXIT has been executed in userspace
-----BEGIN PGP SIGNATURE-----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=51BK
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.13_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix how SEV handles MMIO accesses by forwarding potential page faults
instead of killing the machine and by using the accessors with the
exact functionality needed when accessing memory.
- Fix a confusion with Clang LTO compiler switches passed to the it
- Handle the case gracefully when VMGEXIT has been executed in
userspace
* tag 'x86_urgent_for_v5.13_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev-es: Use __put_user()/__get_user() for data accesses
x86/sev-es: Forward page-faults which happen during emulation
x86/sev-es: Don't return NULL from sev_es_get_ghcb()
x86/build: Fix location of '-plugin-opt=' flags
x86/sev-es: Invalidate the GHCB after completing VMGEXIT
x86/sev-es: Move sev_es_put_ghcb() in prep for follow on patch
Fix breakage of strace (and other ptracers etc.) when using the new scv ABI (Power9 or
later with glibc >= 2.33).
Fix early_ioremap() on 64-bit, which broke booting on some machines.
Thanks to: Dmitry V. Levin, Nicholas Piggin, Alexey Kardashevskiy, Christophe Leroy.
-----BEGIN PGP SIGNATURE-----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=qeQq
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix breakage of strace (and other ptracers etc.) when using the new
scv ABI (Power9 or later with glibc >= 2.33).
- Fix early_ioremap() on 64-bit, which broke booting on some machines.
Thanks to Dmitry V. Levin, Nicholas Piggin, Alexey Kardashevskiy, and
Christophe Leroy.
* tag 'powerpc-5.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s/syscall: Fix ptrace syscall info with scv syscalls
powerpc/64s/syscall: Use pt_regs.trap to distinguish syscall ABI difference between sc and scv syscalls
powerpc: Fix early setup to make early_ioremap() work
Merge misc fixes from Andrew Morton:
"10 patches.
Subsystems affected by this patch series: mm (pagealloc, gup, kasan,
and userfaultfd), ipc, selftests, watchdog, bitmap, procfs, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
userfaultfd: hugetlbfs: fix new flag usage in error path
lib: kunit: suppress a compilation warning of frame size
proc: remove Alexey from MAINTAINERS
linux/bits.h: fix compilation error with GENMASK
watchdog: reliable handling of timestamps
kasan: slab: always reset the tag in get_freepointer_safe()
tools/testing/selftests/exec: fix link error
ipc/mqueue, msg, sem: avoid relying on a stack reference past its expiry
Revert "mm/gup: check page posion status for coredump."
mm/shuffle: fix section mismatch warning
In commit d6995da311 ("hugetlb: use page.private for hugetlb specific
page flags") the use of PagePrivate to indicate a reservation count
should be restored at free time was changed to the hugetlb specific flag
HPageRestoreReserve. Changes to a userfaultfd error path as well as a
VM_BUG_ON() in remove_inode_hugepages() were overlooked.
Users could see incorrect hugetlb reserve counts if they experience an
error with a UFFDIO_COPY operation. Specifically, this would be the
result of an unlikely copy_huge_page_from_user error. There is not an
increased chance of hitting the VM_BUG_ON.
Link: https://lkml.kernel.org/r/20210521233952.236434-1-mike.kravetz@oracle.com
Fixes: d6995da311 ("hugetlb: use page.private for hugetlb specific page flags")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mina Almasry <almasry.mina@google.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/bitfield_kunit.c: In function `test_bitfields_constants':
lib/bitfield_kunit.c:93:1: warning: the frame size of 7456 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
As the description of BITFIELD_KUNIT in lib/Kconfig.debug, it "Only useful
for kernel devs running the KUnit test harness, and not intended for
inclusion into a production build". Therefore, it is not worth modifying
variable 'test_bitfields_constants' to clear this warning. Just suppress
it.
Link: https://lkml.kernel.org/r/20210518094533.7652-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Vitor Massaru Iha <vitor@massaru.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
People Cc me and I don't have time.
Link: https://lkml.kernel.org/r/YKarMxHJBIhMHQIh@localhost.localdomain
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
