There is no need to assign ret variable in ->probe().
Drop useless assignment.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When we count from 0 it's possible to get into off-by-one error.
That's what had happened to this driver. So, correct amount of pins
and related typos in the code.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are
called with desc->lock raw_spinlock held. In mainline this is fine because
spinlock resolves to raw_spinlock. However, running the same code in -rt
we will get a BUG() asserted.
This is because in -rt spinlocks are preemptible so taking the driver
private spinlock in irqchip callbacks causes might_sleep() to trigger.
In order to keep -rt happy but at the same time make sure that register
accesses get serialized, convert the driver to use raw_spinlock instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use local variable to keep device pointer in order to increase readability
of the driver.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are few drivers for Intel SoC GPIO which may utilize
the same data structure to describe this IP.
Share struct intel_pinctrl for wider user.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is a logical continuation of the commit 5fbe5b5883 ("gpio: Initialize
the irqchip valid_mask with a callback") to split IRQ initialization to
hardware and valid mask setup parts.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
After commit 5ea422750a9f ("pinctrl: baytrail: Pass irqchip when
adding gpiochip") the GPIO IRQ chip structure is being initialized
under conditional when IRQ resource has been discovered. But that
commit left aside the assignment of ->init_valid_mask() callback
that is done unconditionally.
For sake of consistency and preventing some garbage in GPIO IRQ chip
structure group initialization together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: 9f573b98ca ("pinctrl: baytrail: Update irq chip operations")
Depends-on: ca8a958e2a ("pinctrl: baytrail: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Split out irq hw-init into a separate chv_gpio_irq_init_hw() function.
This is a preparation patch for passing the irqchip when adding the
gpiochip.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Update North Community pin list to be more clear about pin functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Version 1.1v6 of pin list has some changes in pin names for Intel Lewisburg.
Update the driver accordingly.
Note, it reveals the bug in the driver that misses two pins in GPP_L and
has rather two extra ones. That's why the ordering of some groups is changed.
Fixes: e480b74538 ("pinctrl: intel: Add Intel Lewisburg GPIO support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191120133739.54332-1-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This driver adds pinctrl/GPIO support for Intel Tiger Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc1131 ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf01 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is essentially a revert of:
e3f72b749d pinctrl: cherryview: fix Strago DMI workaround
86c5dd6860 pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
because even with 1.1 versions of BIOS there are some pins that are
configured as interrupts but not claimed by any driver, and they
sometimes fire up and result in interrupt storms that cause touchpad
stop functioning and other issues.
Given that we are unlikely to qualify another firmware version for a
while it is better to keep the workaround active on all Strago boards.
Reported-by: Alex Levin <levinale@chromium.org>
Fixes: 86c5dd6860 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alex Levin <levinale@chromium.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances of
the GPIO chip in the system. This is bad and now we get this warning from
GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: ee1a6ca43d ("pinctrl: intel: Add Intel Broxton pin controller support")
Depends-on: 5ff56b015e ("pinctrl: intel: Disable GPIO pin interrupts in suspend")
Reported-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl2D6y0ACgkQQRCzN7AZ
XXNAfw//Zh0zkrwVSiDU7xgjIgLpngkmPeDoFZoPW5Uqh6G3KlabkE0y7CXZT2kd
hZU0v8CW/947t2zxNev6nNUPumfaTJsj5btVAvF8+QE2lnnbs3Id2mPVPK/mMUs+
bOVFkMMFvGzsY2TaKiJSgOiTe8LoUUl2tJ25mFRBwgtPWYJh2NLVwbzScv+KTBX2
Yy1UhltfWaobyPGgJucZn2yDbkZQeDLyKaExsL9jKBO9rAf8iwSOwkxEz5hLGRri
ejubLV2C5WDcAYIMO2WscFm/0Cxv8ooWBlGTG3+v3P1eaB7l7rYkGpVkoRJpS7gr
Qzf0z1PjVudCcwomkf7ZXJFVHCEkWe86oT4plII9TiZ0b5YpwxYA3Rzakrpb3K7E
gxCuMR1PQK9/2VcqtnXjV2N40KJNRhsAGx47YK3mZxFQun8ksLDTSwKCEPvQ5GT6
3CSYtqVkqgpRaj1MIe+QrFE5Y2bNPjYqXF8kqh5hz/2FWZErbaRuPuKscYh7x0Z4
wY157HEYTlSnSs3nHFtPO3qeXt0i2MNOKVpIlyKzUnafPoyxcnqaB/ZMt5Dp3ygX
NJI3xqULdSzXRpjj/oChCKzuNd9CmxO6yWMIK32f4Gdc3T1wmpBlOTIrHKUA5aZf
KN38L/8iGnzvOKC57552eFpTXaF4Plh2y7e0xQkq4eshhHpz8H8=
=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
The intel_pin_to_gpio() function is only called by the
PM support functions and causes a warning when those are disabled:
drivers/pinctrl/intel/pinctrl-intel.c:841:12: error: unused function 'intel_pin_to_gpio' [-Werror,-Wunused-function]
Mark it __maybe_unused to suppress the warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
On Asus X571GT, GPIO 297 is configured as an interrupt and serves
for the touchpad. The touchpad will report input events much less
than expected after S3 suspend/resume, which results in extremely
slow cursor movement. However, the number of interrupts observed
from /proc/interrupts increases much more than expected even no
touching touchpad.
This is due to the value of PADCFG0 of PIN 225 for the interrupt
has been changed from 0x80800102 to 0x80100102. The GPIROUTIOXAPIC
is toggled on which results in the spurious interrupts. The PADCFG0
of PIN 225 is expected to be saved during suspend, but the 297 is
saved instead because the gpiochip_line_is_irq() expect the GPIO
offset but what's really passed to it is PIN number. In this case,
the /sys/kernel/debug/pinctrl/INT3450:00/gpio-ranges shows
288: INT3450:00 GPIOS [436 - 459] PINS [216 - 239]
So gpiochip_line_is_irq() returns true for GPIO offset 297, the
suspend routine spuriously saves the content for PIN 297 which
we expect to save for PIN 225.
This commit maps the PIN number to GPIO offset first in the
intel_pinctrl_should_save() to make sure the values for the
specific PINs can be correctly saved and then restored.
Fixes: c538b94367 ("pinctrl: intel: Only restore pins that are used by the driver")
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some firmwares would like to protect pads from being modified by OS
and at the same time provide them to OS as a resource. So, the driver
in such circumstances may request pad and may not change its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Version 1.08 of pin list has some changes in pin names for Intel Denverton.
Update the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Replace hard coded constants with self-explanatory names, i.e.
use NSEC_PER_USEC for debounce calculus.
While here, add a unit suffix to debounce period constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
