Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix race with wdev lock/unlock by just acquiring once]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh used to use the mandatory rates as basic rates, but we got
the calculation of mandatory rates wrong until some time ago.
Fix this this broke interoperability with older versions since
now more basic rates are required, and thus the MBSS isn't the
same and the network stops working.
Fix this by simply using only 1Mbps as the basic rate in 2.4GHz.
Since the changed mandatory rates only affected 2.4GHz, this is
all we need to make it work again.
Reported-and-tested-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: 1bd773c077 ("wireless: set correct mandatory rate flags")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When joining a mesh network it is not guaranteed that userspace has a
daemon listening for radar events. This is however required for channels
requiring DFS. To flag that userspace will handle radar events, it needs
to set NL80211_ATTR_HANDLE_DFS.
This matches the current mechanism used for IBSS mode.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DFS requirement for ETSI domain (section 4.7.1.4 in
ETSI EN 301 893 V1.8.1) is the only one which explicitly
states that once DFS channel is marked as available afer
the CAC, this channel will remain in available state even
moving to a different operating channel. But the same is
not explicitly stated in FCC DFS requirement. Also, Pre-CAC
requriements are not explicitly mentioned in FCC requirement.
Current implementation in keeping DFS channel in available
state is same as described in ETSI domain.
For non-ETSI DFS domain, this patch gives a grace period of 2 seconds
since the completion of successful CAC before moving the channel's
DFS state to 'usable' from 'available' state. The same grace period
is checked against the channel's dfs_state_entered timestamp while
deciding if a DFS channel is available for operation. There is a new
radar event, NL80211_RADAR_PRE_CAC_EXPIRED, reported when DFS channel
is moved from available to usable state after the grace period. Also
make sure the DFS channel state is reset to usable once the beaconing
operation on that channel is brought down (like stop_ap, leave_ibss
and leave_mesh) in non-ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is needed for beacon interval validation; if we don't
store it, then new interfaces added won't validate that the
beacon interval is the same as existing ones. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some interface types don't require DFS (such as STATION, P2P_CLIENT
etc). In order to centralize these decisions, make
cfg80211_chandef_dfs_required() take the iftype into consideration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct. We should just make sure
they *are* when we call this function.
Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to break interface combinations in
the following way:
combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20
With the above interface combinations it was
possible to:
step 1. start AP on DFS channel by matching combo 2
step 2. start AP on non-DFS channel by matching combo 1
This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.
The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This permits the use of DFS channel once the CAC is conducted and
no radar is detected.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Secure mesh had the implicit requirement that the Mesh
Peering Management entity be in userspace. However
userspace might want to implement an open MPM as well, so
specify a mesh setup parameter to indicate this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64
text data bss dec hex filename
442825 56230 776 499831 7a077 cfg80211.ko (before)
441585 56230 776 498591 79b9f cfg80211.ko (after)
a reduction of ~1k.
But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix an error on mesh join when no channel has been
explicitly set beforehand.
Also remove a double semicolon.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
devlist_mtx locking is changed to accomodate changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.
STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.
Monitor mode is going to be handled differently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify userspace when a beacon/presp is received from a suitable mesh
peer candidate for whom no sta information exists. Userspace can then
decide to create a sta info for the candidate. If userspace is not
ready to authenticate the peer right away, it can create the sta info
with the authenticated flag unset and set it later.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During mesh setup, use NL80211_MESH_SETUP_USERSPACE_AUTH flag to create
a secure mesh and route management frames to userspace.
Also, NL80211_CMD_GET_WIPHY now returns a flag NL80211_SUPPORT_MESH_AUTH
if the wiphy's mesh implementation supports routing of mesh auth frames
to userspace. This is useful for forward compatibility between old
kernels and new userspace tools.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
