As all packets use the same CTL register masks, we remove duplicated
masks and use common masks instead.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case the clock gating was enabled in preboot we need to disable it
at the H/W initialization stage before touching the MME/TPC registers.
Otherwise, the ASIC can get stuck. If the security is enabled in
the firmware level, the CGM is always disabled and the driver can't
enable it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
FW hard reset capability indication is now moved to preboot stage.
Driver will check if HW is dirty only after it validated preboot
is up. If HW is dirty, driver will perform a hard reset according
to the FW capability.
In addition, FW defines a new message which driver need to send in
order to initiate a hard reset.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
These defines are 64-bit defines so they need ull suffix.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once firmware security is enabled, driver must fetch pll frequencies
through the firmware message interface instead of reading the registers
directly.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once FW security is enabled there is no access to HBM ecc registers,
need to read values from FW using a dedicated interface.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must fetch FW hard reset capability during boot time,
in order to skip the hard reset flow if necessary.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support for fetching security indication from FW.
This indication is needed in order to skip unnecessary
initializations done by FW.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add new structures and messages that the driver use to interact with the
firmware to receive information and events (errors) about GAUDI's NIC.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add auto-generated header files that describe the NIC QMANs registers
used by the driver.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This interrupt cause is not relevant because of how the user use the
QMAN arbitration mechanism. We must mask it as the log explodes with it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Our firmware use some scratchpad registers in the device for different
roles. Update the file to the latest version of the firmware code.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add new packet to fetch PLL information from firmware. This will be needed
in the future when the driver won't be able to access the PLL registers
directly
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit adds the number of HOPs supported by the device to the
device MMU properties.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For future ASICs, we increase this field by one nibble. This field was not
used by the current ASICs so this change doesn't break anything.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Because the device CPU compiler aligns structures to 8 bytes,
struct cpucp_info has an alignment issue as some parts
in the structure are not aligned to 8 bytes.
It is preferred that we explicitly insert placeholders inside
the structure to avoid confusion
in order to validate this scenario, we printed both pointers:
__u8 cpucp_version[VERSION_MAX_LEN]; (0xffff899c67ed4cbc)
__le64 dram_size; (0xffff899c67ed4d40)
we see difference of 132 bytes although the first array
is only 128 bytes long, Meaning compiler added a 4 byte padding.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
ArmCP mandates that the device CPU is always an ARM processor, which might
be wrong in the future.
Most of this change is an internal renaming of variables, functions and
defines but there are two entries in sysfs which have armcp in their
names. Add identical cpucp entries but don't remove yet the armcp entries.
Those will be deprecated next year. Add the documentation about it in sysfs
documentation.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add driver implementation for reading the total energy consumption
from the device ARM FW.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Include linux/bitfield.h only in habanalabs.h, instead of in each and
every file that needs it, as habanalabs.h is already included by all.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use the standard FIELD_PREP() macro instead of << operator to perform
bitmask operations. This ensures type check safety and eliminate compiler
warnings.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Update firmware header with new API for getting pcie info
such as tx/rx throughput and replay counter.
These counters are needed by customers for monitor and maintenance
of multiple devices.
Add new opcodes to the INFO ioctl to retrieve these counters.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
All initiator coordinates received upon an 'MMU page fault RAZWI
event' should be the routers coordinates, the only exception is the
DMA initiators for which the reported coordinates correspond to
their actual location.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Update the boot interface file from the latest version from firmware.
Defines for secure boot were added.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
For internal needs of our CI we need to move all the common code into a
common folder instead of putting them in the root folder of the driver.
Same applies to the common header files under include/
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Currently the driver halts the device CPU in the halt engines function,
which halts all the engines of the ASIC. The problem is that if later on we
stop the reset process (due to inability to clean memory mappings in time),
the CPU will remain in halt mode. This creates many issues, such as
thermal/power control and FLR handling.
Therefore, move the halting of the device CPU to the very end of the reset
process, just before writing to the registers to initiate the reset. In
addition, the driver now needs to send a message to the device F/W to
disable it from sending interrupts to the host machine because during halt
engines function the driver disables the MSI/MSI-X interrupts.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
ECC (Error Correcting Code) interrupts are going to be handled
by the FW. Hence, we define an interface in which the driver can
obtain the relevant ECC information.
This information is needed for monitoring and can also lead
to a hard reset if ECC error is not correctable.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The profiler needs to know the PLL values for correctly showing the
profiling data. Because our firmware can use different PLL configurations,
we need to read the PLL values from the ASIC to pass them to the profiler.
Signed-off-by: Adam Aharon <aaharon@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Once there is a 64-bit field in a structure, GCC compiler for ARM aligns
the structure to 8 bytes. In order to avoid confusion when these
structures are being passed between CPUs from different architectures, we
explicitly align the structure to 8 bytes.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In Gaudi, the user can't execute scalar load_and_exe on external queue
because it can be a security hole. The driver doesn't parse the commands
being loaded and it can be msg_prot, which the user isn't allowed to use.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Instead of writing similar event handling code for each ASIC, move the code
to the common firmware file. This code will be used for GAUDI and all
future ASICs.
In addition, add two new fields to the auto-generated events file: valid
and description. This will save the need to manually write the events
description in the source code and simplify the code.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the ASIC-dependent code for GAUDI. Supply (almost) all of the function
callbacks that the driver's common code need to initialize, finalize and
submit workloads to the GAUDI ASIC.
It also contains the code to initialize the F/W of the GAUDI ASIC and to
receive events from the F/W.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the relevant GAUDI ASIC registers header files. These files are
generated automatically from a tool maintained by the VLSI engineers.
There are more files which are not upstreamed because only very few defines
from those files are used in the driver. For those files, we copied the
relevant defines into gaudi_regs.h and gaudi_masks.h, to reduce the size of
this patch.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For Gaudi the driver gets two new additional properties from the F/W:
1. The card's type - PCI or PMC
2. The card's location in the Gaudi's box (relevant only for PMC).
The card's location is also passed to the user in the HW IP info structure
as it needs this property for establishing communication between Gaudis.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Update the mapping to the latest one used by the Firmware. No impact on the
driver in this update.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Load CPU device boot loader during driver boot time in order to avoid flash
write for every boot loader update.
To preserve backward-compatibility, skip the device boot load if the device
doesn't request it.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add a new opcode to the INFO IOCTL that retrieves the device time
alongside the host time, to allow a user application that want to measure
device time together with host time (such as a profiler) to synchronize
these times.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Retrieve from the firmware the DMA mask value we need to set according to
the device's PCI controller configuration. This is needed when working on
POWER9 machines, as the device's PCI controller is configured in a
different way in those machines.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add comments for the various errors and states of the firmware during boot.
Add a mapping of a new register that will tell the driver whether the
firmware executed the request from the driver or if it has encountered an
error.
Add a new enum for the possible values of this register.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Move the code of device CPU initialization from being ASIC-Dependent to
common code. In addition, add support for the new error reporting feature
of the firmware boot code.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Stop-on-error mode in DMA is useful as it stops the transaction
immediately upon error e.g. page fault.
But it may cause the next command submission to fail as is leaves the DMA
in unstable state.
Therefore we remove the stop-on-error configuration from the DMA.
Stop-on-err is still available for debug.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add print upon clock slow down due to power consumption or overheating.
In addition, add print when back to optimal clock.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add support for hwmon_in_highest, hwmon_temp_highest and hwmon_curr_highest
attributes. These attributes retrieve the historical maximum voltage,
temperature and current that were sampled, respectively.
Signed-off-by: Christine Gharzuzi <cgharzuzi@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
