Very sporadically I had test case btrfs/069 from fstests hanging (for
years, it is not a recent regression), with the following traces in
dmesg/syslog:
[162301.160628] BTRFS info (device sdc): dev_replace from /dev/sdd (devid 2) to /dev/sdg started
[162301.181196] BTRFS info (device sdc): scrub: finished on devid 4 with status: 0
[162301.287162] BTRFS info (device sdc): dev_replace from /dev/sdd (devid 2) to /dev/sdg finished
[162513.513792] INFO: task btrfs-transacti:1356167 blocked for more than 120 seconds.
[162513.514318] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.514522] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.514747] task:btrfs-transacti state:D stack: 0 pid:1356167 ppid: 2 flags:0x00004000
[162513.514751] Call Trace:
[162513.514761] __schedule+0x5ce/0xd00
[162513.514765] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.514771] schedule+0x46/0xf0
[162513.514844] wait_current_trans+0xde/0x140 [btrfs]
[162513.514850] ? finish_wait+0x90/0x90
[162513.514864] start_transaction+0x37c/0x5f0 [btrfs]
[162513.514879] transaction_kthread+0xa4/0x170 [btrfs]
[162513.514891] ? btrfs_cleanup_transaction+0x660/0x660 [btrfs]
[162513.514894] kthread+0x153/0x170
[162513.514897] ? kthread_stop+0x2c0/0x2c0
[162513.514902] ret_from_fork+0x22/0x30
[162513.514916] INFO: task fsstress:1356184 blocked for more than 120 seconds.
[162513.515192] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.515431] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.515680] task:fsstress state:D stack: 0 pid:1356184 ppid:1356177 flags:0x00004000
[162513.515682] Call Trace:
[162513.515688] __schedule+0x5ce/0xd00
[162513.515691] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.515697] schedule+0x46/0xf0
[162513.515712] wait_current_trans+0xde/0x140 [btrfs]
[162513.515716] ? finish_wait+0x90/0x90
[162513.515729] start_transaction+0x37c/0x5f0 [btrfs]
[162513.515743] btrfs_attach_transaction_barrier+0x1f/0x50 [btrfs]
[162513.515753] btrfs_sync_fs+0x61/0x1c0 [btrfs]
[162513.515758] ? __ia32_sys_fdatasync+0x20/0x20
[162513.515761] iterate_supers+0x87/0xf0
[162513.515765] ksys_sync+0x60/0xb0
[162513.515768] __do_sys_sync+0xa/0x10
[162513.515771] do_syscall_64+0x33/0x80
[162513.515774] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[162513.515781] RIP: 0033:0x7f5238f50bd7
[162513.515782] Code: Bad RIP value.
[162513.515784] RSP: 002b:00007fff67b978e8 EFLAGS: 00000206 ORIG_RAX: 00000000000000a2
[162513.515786] RAX: ffffffffffffffda RBX: 000055b1fad2c560 RCX: 00007f5238f50bd7
[162513.515788] RDX: 00000000ffffffff RSI: 000000000daf0e74 RDI: 000000000000003a
[162513.515789] RBP: 0000000000000032 R08: 000000000000000a R09: 00007f5239019be0
[162513.515791] R10: fffffffffffff24f R11: 0000000000000206 R12: 000000000000003a
[162513.515792] R13: 00007fff67b97950 R14: 00007fff67b97906 R15: 000055b1fad1a340
[162513.515804] INFO: task fsstress:1356185 blocked for more than 120 seconds.
[162513.516064] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.516329] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.516617] task:fsstress state:D stack: 0 pid:1356185 ppid:1356177 flags:0x00000000
[162513.516620] Call Trace:
[162513.516625] __schedule+0x5ce/0xd00
[162513.516628] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.516634] schedule+0x46/0xf0
[162513.516647] wait_current_trans+0xde/0x140 [btrfs]
[162513.516650] ? finish_wait+0x90/0x90
[162513.516662] start_transaction+0x4d7/0x5f0 [btrfs]
[162513.516679] btrfs_setxattr_trans+0x3c/0x100 [btrfs]
[162513.516686] __vfs_setxattr+0x66/0x80
[162513.516691] __vfs_setxattr_noperm+0x70/0x200
[162513.516697] vfs_setxattr+0x6b/0x120
[162513.516703] setxattr+0x125/0x240
[162513.516709] ? lock_acquire+0xb1/0x480
[162513.516712] ? mnt_want_write+0x20/0x50
[162513.516721] ? rcu_read_lock_any_held+0x8e/0xb0
[162513.516723] ? preempt_count_add+0x49/0xa0
[162513.516725] ? __sb_start_write+0x19b/0x290
[162513.516727] ? preempt_count_add+0x49/0xa0
[162513.516732] path_setxattr+0xba/0xd0
[162513.516739] __x64_sys_setxattr+0x27/0x30
[162513.516741] do_syscall_64+0x33/0x80
[162513.516743] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[162513.516745] RIP: 0033:0x7f5238f56d5a
[162513.516746] Code: Bad RIP value.
[162513.516748] RSP: 002b:00007fff67b97868 EFLAGS: 00000202 ORIG_RAX: 00000000000000bc
[162513.516750] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f5238f56d5a
[162513.516751] RDX: 000055b1fbb0d5a0 RSI: 00007fff67b978a0 RDI: 000055b1fbb0d470
[162513.516753] RBP: 000055b1fbb0d5a0 R08: 0000000000000001 R09: 00007fff67b97700
[162513.516754] R10: 0000000000000004 R11: 0000000000000202 R12: 0000000000000004
[162513.516756] R13: 0000000000000024 R14: 0000000000000001 R15: 00007fff67b978a0
[162513.516767] INFO: task fsstress:1356196 blocked for more than 120 seconds.
[162513.517064] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.517365] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.517763] task:fsstress state:D stack: 0 pid:1356196 ppid:1356177 flags:0x00004000
[162513.517780] Call Trace:
[162513.517786] __schedule+0x5ce/0xd00
[162513.517789] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.517796] schedule+0x46/0xf0
[162513.517810] wait_current_trans+0xde/0x140 [btrfs]
[162513.517814] ? finish_wait+0x90/0x90
[162513.517829] start_transaction+0x37c/0x5f0 [btrfs]
[162513.517845] btrfs_attach_transaction_barrier+0x1f/0x50 [btrfs]
[162513.517857] btrfs_sync_fs+0x61/0x1c0 [btrfs]
[162513.517862] ? __ia32_sys_fdatasync+0x20/0x20
[162513.517865] iterate_supers+0x87/0xf0
[162513.517869] ksys_sync+0x60/0xb0
[162513.517872] __do_sys_sync+0xa/0x10
[162513.517875] do_syscall_64+0x33/0x80
[162513.517878] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[162513.517881] RIP: 0033:0x7f5238f50bd7
[162513.517883] Code: Bad RIP value.
[162513.517885] RSP: 002b:00007fff67b978e8 EFLAGS: 00000206 ORIG_RAX: 00000000000000a2
[162513.517887] RAX: ffffffffffffffda RBX: 000055b1fad2c560 RCX: 00007f5238f50bd7
[162513.517889] RDX: 0000000000000000 RSI: 000000007660add2 RDI: 0000000000000053
[162513.517891] RBP: 0000000000000032 R08: 0000000000000067 R09: 00007f5239019be0
[162513.517893] R10: fffffffffffff24f R11: 0000000000000206 R12: 0000000000000053
[162513.517895] R13: 00007fff67b97950 R14: 00007fff67b97906 R15: 000055b1fad1a340
[162513.517908] INFO: task fsstress:1356197 blocked for more than 120 seconds.
[162513.518298] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.518672] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.519157] task:fsstress state:D stack: 0 pid:1356197 ppid:1356177 flags:0x00000000
[162513.519160] Call Trace:
[162513.519165] __schedule+0x5ce/0xd00
[162513.519168] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.519174] schedule+0x46/0xf0
[162513.519190] wait_current_trans+0xde/0x140 [btrfs]
[162513.519193] ? finish_wait+0x90/0x90
[162513.519206] start_transaction+0x4d7/0x5f0 [btrfs]
[162513.519222] btrfs_create+0x57/0x200 [btrfs]
[162513.519230] lookup_open+0x522/0x650
[162513.519246] path_openat+0x2b8/0xa50
[162513.519270] do_filp_open+0x91/0x100
[162513.519275] ? find_held_lock+0x32/0x90
[162513.519280] ? lock_acquired+0x33b/0x470
[162513.519285] ? do_raw_spin_unlock+0x4b/0xc0
[162513.519287] ? _raw_spin_unlock+0x29/0x40
[162513.519295] do_sys_openat2+0x20d/0x2d0
[162513.519300] do_sys_open+0x44/0x80
[162513.519304] do_syscall_64+0x33/0x80
[162513.519307] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[162513.519309] RIP: 0033:0x7f5238f4a903
[162513.519310] Code: Bad RIP value.
[162513.519312] RSP: 002b:00007fff67b97758 EFLAGS: 00000246 ORIG_RAX: 0000000000000055
[162513.519314] RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007f5238f4a903
[162513.519316] RDX: 0000000000000000 RSI: 00000000000001b6 RDI: 000055b1fbb0d470
[162513.519317] RBP: 00007fff67b978c0 R08: 0000000000000001 R09: 0000000000000002
[162513.519319] R10: 00007fff67b974f7 R11: 0000000000000246 R12: 0000000000000013
[162513.519320] R13: 00000000000001b6 R14: 00007fff67b97906 R15: 000055b1fad1c620
[162513.519332] INFO: task btrfs:1356211 blocked for more than 120 seconds.
[162513.519727] Not tainted 5.9.0-rc6-btrfs-next-69 #1
[162513.520115] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[162513.520508] task:btrfs state:D stack: 0 pid:1356211 ppid:1356178 flags:0x00004002
[162513.520511] Call Trace:
[162513.520516] __schedule+0x5ce/0xd00
[162513.520519] ? _raw_spin_unlock_irqrestore+0x3c/0x60
[162513.520525] schedule+0x46/0xf0
[162513.520544] btrfs_scrub_pause+0x11f/0x180 [btrfs]
[162513.520548] ? finish_wait+0x90/0x90
[162513.520562] btrfs_commit_transaction+0x45a/0xc30 [btrfs]
[162513.520574] ? start_transaction+0xe0/0x5f0 [btrfs]
[162513.520596] btrfs_dev_replace_finishing+0x6d8/0x711 [btrfs]
[162513.520619] btrfs_dev_replace_by_ioctl.cold+0x1cc/0x1fd [btrfs]
[162513.520639] btrfs_ioctl+0x2a25/0x36f0 [btrfs]
[162513.520643] ? do_sigaction+0xf3/0x240
[162513.520645] ? find_held_lock+0x32/0x90
[162513.520648] ? do_sigaction+0xf3/0x240
[162513.520651] ? lock_acquired+0x33b/0x470
[162513.520655] ? _raw_spin_unlock_irq+0x24/0x50
[162513.520657] ? lockdep_hardirqs_on+0x7d/0x100
[162513.520660] ? _raw_spin_unlock_irq+0x35/0x50
[162513.520662] ? do_sigaction+0xf3/0x240
[162513.520671] ? __x64_sys_ioctl+0x83/0xb0
[162513.520672] __x64_sys_ioctl+0x83/0xb0
[162513.520677] do_syscall_64+0x33/0x80
[162513.520679] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[162513.520681] RIP: 0033:0x7fc3cd307d87
[162513.520682] Code: Bad RIP value.
[162513.520684] RSP: 002b:00007ffe30a56bb8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[162513.520686] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007fc3cd307d87
[162513.520687] RDX: 00007ffe30a57a30 RSI: 00000000ca289435 RDI: 0000000000000003
[162513.520689] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[162513.520690] R10: 0000000000000008 R11: 0000000000000202 R12: 0000000000000003
[162513.520692] R13: 0000557323a212e0 R14: 00007ffe30a5a520 R15: 0000000000000001
[162513.520703]
Showing all locks held in the system:
[162513.520712] 1 lock held by khungtaskd/54:
[162513.520713] #0: ffffffffb40a91a0 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x15/0x197
[162513.520728] 1 lock held by in:imklog/596:
[162513.520729] #0: ffff8f3f0d781400 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0x4d/0x60
[162513.520782] 1 lock held by btrfs-transacti/1356167:
[162513.520784] #0: ffff8f3d810cc848 (&fs_info->transaction_kthread_mutex){+.+.}-{3:3}, at: transaction_kthread+0x4a/0x170 [btrfs]
[162513.520798] 1 lock held by btrfs/1356190:
[162513.520800] #0: ffff8f3d57644470 (sb_writers#15){.+.+}-{0:0}, at: mnt_want_write_file+0x22/0x60
[162513.520805] 1 lock held by fsstress/1356184:
[162513.520806] #0: ffff8f3d576440e8 (&type->s_umount_key#62){++++}-{3:3}, at: iterate_supers+0x6f/0xf0
[162513.520811] 3 locks held by fsstress/1356185:
[162513.520812] #0: ffff8f3d57644470 (sb_writers#15){.+.+}-{0:0}, at: mnt_want_write+0x20/0x50
[162513.520815] #1: ffff8f3d80a650b8 (&type->i_mutex_dir_key#10){++++}-{3:3}, at: vfs_setxattr+0x50/0x120
[162513.520820] #2: ffff8f3d57644690 (sb_internal#2){.+.+}-{0:0}, at: start_transaction+0x40e/0x5f0 [btrfs]
[162513.520833] 1 lock held by fsstress/1356196:
[162513.520834] #0: ffff8f3d576440e8 (&type->s_umount_key#62){++++}-{3:3}, at: iterate_supers+0x6f/0xf0
[162513.520838] 3 locks held by fsstress/1356197:
[162513.520839] #0: ffff8f3d57644470 (sb_writers#15){.+.+}-{0:0}, at: mnt_want_write+0x20/0x50
[162513.520843] #1: ffff8f3d506465e8 (&type->i_mutex_dir_key#10){++++}-{3:3}, at: path_openat+0x2a7/0xa50
[162513.520846] #2: ffff8f3d57644690 (sb_internal#2){.+.+}-{0:0}, at: start_transaction+0x40e/0x5f0 [btrfs]
[162513.520858] 2 locks held by btrfs/1356211:
[162513.520859] #0: ffff8f3d810cde30 (&fs_info->dev_replace.lock_finishing_cancel_unmount){+.+.}-{3:3}, at: btrfs_dev_replace_finishing+0x52/0x711 [btrfs]
[162513.520877] #1: ffff8f3d57644690 (sb_internal#2){.+.+}-{0:0}, at: start_transaction+0x40e/0x5f0 [btrfs]
This was weird because the stack traces show that a transaction commit,
triggered by a device replace operation, is blocking trying to pause any
running scrubs but there are no stack traces of blocked tasks doing a
scrub.
After poking around with drgn, I noticed there was a scrub task that was
constantly running and blocking for shorts periods of time:
>>> t = find_task(prog, 1356190)
>>> prog.stack_trace(t)
#0 __schedule+0x5ce/0xcfc
#1 schedule+0x46/0xe4
#2 schedule_timeout+0x1df/0x475
#3 btrfs_reada_wait+0xda/0x132
#4 scrub_stripe+0x2a8/0x112f
#5 scrub_chunk+0xcd/0x134
#6 scrub_enumerate_chunks+0x29e/0x5ee
#7 btrfs_scrub_dev+0x2d5/0x91b
#8 btrfs_ioctl+0x7f5/0x36e7
#9 __x64_sys_ioctl+0x83/0xb0
#10 do_syscall_64+0x33/0x77
#11 entry_SYSCALL_64+0x7c/0x156
Which corresponds to:
int btrfs_reada_wait(void *handle)
{
struct reada_control *rc = handle;
struct btrfs_fs_info *fs_info = rc->fs_info;
while (atomic_read(&rc->elems)) {
if (!atomic_read(&fs_info->reada_works_cnt))
reada_start_machine(fs_info);
wait_event_timeout(rc->wait, atomic_read(&rc->elems) == 0,
(HZ + 9) / 10);
}
(...)
So the counter "rc->elems" was set to 1 and never decreased to 0, causing
the scrub task to loop forever in that function. Then I used the following
script for drgn to check the readahead requests:
$ cat dump_reada.py
import sys
import drgn
from drgn import NULL, Object, cast, container_of, execscript, \
reinterpret, sizeof
from drgn.helpers.linux import *
mnt_path = b"/home/fdmanana/btrfs-tests/scratch_1"
mnt = None
for mnt in for_each_mount(prog, dst = mnt_path):
pass
if mnt is None:
sys.stderr.write(f'Error: mount point {mnt_path} not found\n')
sys.exit(1)
fs_info = cast('struct btrfs_fs_info *', mnt.mnt.mnt_sb.s_fs_info)
def dump_re(re):
nzones = re.nzones.value_()
print(f're at {hex(re.value_())}')
print(f'\t logical {re.logical.value_()}')
print(f'\t refcnt {re.refcnt.value_()}')
print(f'\t nzones {nzones}')
for i in range(nzones):
dev = re.zones[i].device
name = dev.name.str.string_()
print(f'\t\t dev id {dev.devid.value_()} name {name}')
print()
for _, e in radix_tree_for_each(fs_info.reada_tree):
re = cast('struct reada_extent *', e)
dump_re(re)
$ drgn dump_reada.py
re at 0xffff8f3da9d25ad8
logical 38928384
refcnt 1
nzones 1
dev id 0 name b'/dev/sdd'
$
So there was one readahead extent with a single zone corresponding to the
source device of that last device replace operation logged in dmesg/syslog.
Also the ID of that zone's device was 0 which is a special value set in
the source device of a device replace operation when the operation finishes
(constant BTRFS_DEV_REPLACE_DEVID set at btrfs_dev_replace_finishing()),
confirming again that device /dev/sdd was the source of a device replace
operation.
Normally there should be as many zones in the readahead extent as there are
devices, and I wasn't expecting the extent to be in a block group with a
'single' profile, so I went and confirmed with the following drgn script
that there weren't any single profile block groups:
$ cat dump_block_groups.py
import sys
import drgn
from drgn import NULL, Object, cast, container_of, execscript, \
reinterpret, sizeof
from drgn.helpers.linux import *
mnt_path = b"/home/fdmanana/btrfs-tests/scratch_1"
mnt = None
for mnt in for_each_mount(prog, dst = mnt_path):
pass
if mnt is None:
sys.stderr.write(f'Error: mount point {mnt_path} not found\n')
sys.exit(1)
fs_info = cast('struct btrfs_fs_info *', mnt.mnt.mnt_sb.s_fs_info)
BTRFS_BLOCK_GROUP_DATA = (1 << 0)
BTRFS_BLOCK_GROUP_SYSTEM = (1 << 1)
BTRFS_BLOCK_GROUP_METADATA = (1 << 2)
BTRFS_BLOCK_GROUP_RAID0 = (1 << 3)
BTRFS_BLOCK_GROUP_RAID1 = (1 << 4)
BTRFS_BLOCK_GROUP_DUP = (1 << 5)
BTRFS_BLOCK_GROUP_RAID10 = (1 << 6)
BTRFS_BLOCK_GROUP_RAID5 = (1 << 7)
BTRFS_BLOCK_GROUP_RAID6 = (1 << 8)
BTRFS_BLOCK_GROUP_RAID1C3 = (1 << 9)
BTRFS_BLOCK_GROUP_RAID1C4 = (1 << 10)
def bg_flags_string(bg):
flags = bg.flags.value_()
ret = ''
if flags & BTRFS_BLOCK_GROUP_DATA:
ret = 'data'
if flags & BTRFS_BLOCK_GROUP_METADATA:
if len(ret) > 0:
ret += '|'
ret += 'meta'
if flags & BTRFS_BLOCK_GROUP_SYSTEM:
if len(ret) > 0:
ret += '|'
ret += 'system'
if flags & BTRFS_BLOCK_GROUP_RAID0:
ret += ' raid0'
elif flags & BTRFS_BLOCK_GROUP_RAID1:
ret += ' raid1'
elif flags & BTRFS_BLOCK_GROUP_DUP:
ret += ' dup'
elif flags & BTRFS_BLOCK_GROUP_RAID10:
ret += ' raid10'
elif flags & BTRFS_BLOCK_GROUP_RAID5:
ret += ' raid5'
elif flags & BTRFS_BLOCK_GROUP_RAID6:
ret += ' raid6'
elif flags & BTRFS_BLOCK_GROUP_RAID1C3:
ret += ' raid1c3'
elif flags & BTRFS_BLOCK_GROUP_RAID1C4:
ret += ' raid1c4'
else:
ret += ' single'
return ret
def dump_bg(bg):
print()
print(f'block group at {hex(bg.value_())}')
print(f'\t start {bg.start.value_()} length {bg.length.value_()}')
print(f'\t flags {bg.flags.value_()} - {bg_flags_string(bg)}')
bg_root = fs_info.block_group_cache_tree.address_of_()
for bg in rbtree_inorder_for_each_entry('struct btrfs_block_group', bg_root, 'cache_node'):
dump_bg(bg)
$ drgn dump_block_groups.py
block group at 0xffff8f3d673b0400
start 22020096 length 16777216
flags 258 - system raid6
block group at 0xffff8f3d53ddb400
start 38797312 length 536870912
flags 260 - meta raid6
block group at 0xffff8f3d5f4d9c00
start 575668224 length 2147483648
flags 257 - data raid6
block group at 0xffff8f3d08189000
start 2723151872 length 67108864
flags 258 - system raid6
block group at 0xffff8f3db70ff000
start 2790260736 length 1073741824
flags 260 - meta raid6
block group at 0xffff8f3d5f4dd800
start 3864002560 length 67108864
flags 258 - system raid6
block group at 0xffff8f3d67037000
start 3931111424 length 2147483648
flags 257 - data raid6
$
So there were only 2 reasons left for having a readahead extent with a
single zone: reada_find_zone(), called when creating a readahead extent,
returned NULL either because we failed to find the corresponding block
group or because a memory allocation failed. With some additional and
custom tracing I figured out that on every further ocurrence of the
problem the block group had just been deleted when we were looping to
create the zones for the readahead extent (at reada_find_extent()), so we
ended up with only one zone in the readahead extent, corresponding to a
device that ends up getting replaced.
So after figuring that out it became obvious why the hang happens:
1) Task A starts a scrub on any device of the filesystem, except for
device /dev/sdd;
2) Task B starts a device replace with /dev/sdd as the source device;
3) Task A calls btrfs_reada_add() from scrub_stripe() and it is currently
starting to scrub a stripe from block group X. This call to
btrfs_reada_add() is the one for the extent tree. When btrfs_reada_add()
calls reada_add_block(), it passes the logical address of the extent
tree's root node as its 'logical' argument - a value of 38928384;
4) Task A then enters reada_find_extent(), called from reada_add_block().
It finds there isn't any existing readahead extent for the logical
address 38928384, so it proceeds to the path of creating a new one.
It calls btrfs_map_block() to find out which stripes exist for the block
group X. On the first iteration of the for loop that iterates over the
stripes, it finds the stripe for device /dev/sdd, so it creates one
zone for that device and adds it to the readahead extent. Before getting
into the second iteration of the loop, the cleanup kthread deletes block
group X because it was empty. So in the iterations for the remaining
stripes it does not add more zones to the readahead extent, because the
calls to reada_find_zone() returned NULL because they couldn't find
block group X anymore.
As a result the new readahead extent has a single zone, corresponding to
the device /dev/sdd;
4) Before task A returns to btrfs_reada_add() and queues the readahead job
for the readahead work queue, task B finishes the device replace and at
btrfs_dev_replace_finishing() swaps the device /dev/sdd with the new
device /dev/sdg;
5) Task A returns to reada_add_block(), which increments the counter
"->elems" of the reada_control structure allocated at btrfs_reada_add().
Then it returns back to btrfs_reada_add() and calls
reada_start_machine(). This queues a job in the readahead work queue to
run the function reada_start_machine_worker(), which calls
__reada_start_machine().
At __reada_start_machine() we take the device list mutex and for each
device found in the current device list, we call
reada_start_machine_dev() to start the readahead work. However at this
point the device /dev/sdd was already freed and is not in the device
list anymore.
This means the corresponding readahead for the extent at 38928384 is
never started, and therefore the "->elems" counter of the reada_control
structure allocated at btrfs_reada_add() never goes down to 0, causing
the call to btrfs_reada_wait(), done by the scrub task, to wait forever.
Note that the readahead request can be made either after the device replace
started or before it started, however in pratice it is very unlikely that a
device replace is able to start after a readahead request is made and is
able to complete before the readahead request completes - maybe only on a
very small and nearly empty filesystem.
This hang however is not the only problem we can have with readahead and
device removals. When the readahead extent has other zones other than the
one corresponding to the device that is being removed (either by a device
replace or a device remove operation), we risk having a use-after-free on
the device when dropping the last reference of the readahead extent.
For example if we create a readahead extent with two zones, one for the
device /dev/sdd and one for the device /dev/sde:
1) Before the readahead worker starts, the device /dev/sdd is removed,
and the corresponding btrfs_device structure is freed. However the
readahead extent still has the zone pointing to the device structure;
2) When the readahead worker starts, it only finds device /dev/sde in the
current device list of the filesystem;
3) It starts the readahead work, at reada_start_machine_dev(), using the
device /dev/sde;
4) Then when it finishes reading the extent from device /dev/sde, it calls
__readahead_hook() which ends up dropping the last reference on the
readahead extent through the last call to reada_extent_put();
5) At reada_extent_put() it iterates over each zone of the readahead extent
and attempts to delete an element from the device's 'reada_extents'
radix tree, resulting in a use-after-free, as the device pointer of the
zone for /dev/sdd is now stale. We can also access the device after
dropping the last reference of a zone, through reada_zone_release(),
also called by reada_extent_put().
And a device remove suffers the same problem, however since it shrinks the
device size down to zero before removing the device, it is very unlikely to
still have readahead requests not completed by the time we free the device,
the only possibility is if the device has a very little space allocated.
While the hang problem is exclusive to scrub, since it is currently the
only user of btrfs_reada_add() and btrfs_reada_wait(), the use-after-free
problem affects any path that triggers readhead, which includes
btree_readahead_hook() and __readahead_hook() (a readahead worker can
trigger readahed for the children of a node) for example - any path that
ends up calling reada_add_block() can trigger the use-after-free after a
device is removed.
So fix this by waiting for any readahead requests for a device to complete
before removing a device, ensuring that while waiting for existing ones no
new ones can be made.
This problem has been around for a very long time - the readahead code was
added in 2011, device remove exists since 2008 and device replace was
introduced in 2013, hard to pick a specific commit for a git Fixes tag.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The function is short and simple, we can get rid of the declaration as
it's not necessary for a static function. Move it before its first
caller. No functional changes.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In the function btrfs_init_dev_replace_tgtdev(), the local variable
devices is used only once, we can remove it.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Similar to btrfs_sysfs_add_devices_dir()'s refactoring, split
btrfs_sysfs_remove_devices_dir() so that we don't have to use the device
argument to indicate whether to free all devices or just one device.
Export btrfs_sysfs_remove_device() as device operations outside of
sysfs.c now calls this instead of btrfs_sysfs_remove_devices_dir().
btrfs_sysfs_remove_devices_dir() is renamed to
btrfs_sysfs_remove_fs_devices() to suite its new role.
Now, no one outside of sysfs.c calls btrfs_sysfs_remove_fs_devices()
so it is redeclared s static. And the same function had to be moved
before its first caller.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we add a device we need to add it to sysfs, so instead of using the
btrfs_sysfs_add_devices_dir() fs_devices argument to specify whether to
add a device or all of fs_devices, call the helper function directly
btrfs_sysfs_add_device() and thus make it non-static.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If you replace a seed device in a sprouted fs, it appears to have
successfully replaced the seed device, but if you look closely, it
didn't. Here is an example.
$ mkfs.btrfs /dev/sda
$ btrfstune -S1 /dev/sda
$ mount /dev/sda /btrfs
$ btrfs device add /dev/sdb /btrfs
$ umount /btrfs
$ btrfs device scan --forget
$ mount -o device=/dev/sda /dev/sdb /btrfs
$ btrfs replace start -f /dev/sda /dev/sdc /btrfs
$ echo $?
0
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc started
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc finished
$ btrfs fi show
Label: none uuid: ab2c88b7-be81-4a7e-9849-c3666e7f9f4f
Total devices 2 FS bytes used 256.00KiB
devid 1 size 3.00GiB used 520.00MiB path /dev/sdc
devid 2 size 3.00GiB used 896.00MiB path /dev/sdb
Label: none uuid: 10bd3202-0415-43af-96a8-d5409f310a7e
Total devices 1 FS bytes used 128.00KiB
devid 1 size 3.00GiB used 536.00MiB path /dev/sda
So as per the replace start command and kernel log replace was successful.
Now let's try to clean mount.
$ umount /btrfs
$ btrfs device scan --forget
$ mount -o device=/dev/sdc /dev/sdb /btrfs
mount: /btrfs: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error.
[ 636.157517] BTRFS error (device sdc): failed to read chunk tree: -2
[ 636.180177] BTRFS error (device sdc): open_ctree failed
That's because per dev items it is still looking for the original seed
device.
$ btrfs inspect-internal dump-tree -d /dev/sdb
item 0 key (DEV_ITEMS DEV_ITEM 1) itemoff 16185 itemsize 98
devid 1 total_bytes 3221225472 bytes_used 545259520
io_align 4096 io_width 4096 sector_size 4096 type 0
generation 6 start_offset 0 dev_group 0
seek_speed 0 bandwidth 0
uuid 59368f50-9af2-4b17-91da-8a783cc418d4 <--- seed uuid
fsid 10bd3202-0415-43af-96a8-d5409f310a7e <--- seed fsid
item 1 key (DEV_ITEMS DEV_ITEM 2) itemoff 16087 itemsize 98
devid 2 total_bytes 3221225472 bytes_used 939524096
io_align 4096 io_width 4096 sector_size 4096 type 0
generation 0 start_offset 0 dev_group 0
seek_speed 0 bandwidth 0
uuid 56a0a6bc-4630-4998-8daf-3c3030c4256a <- sprout uuid
fsid ab2c88b7-be81-4a7e-9849-c3666e7f9f4f <- sprout fsid
But the replaced target has the following uuid+fsid in its superblock
which doesn't match with the expected uuid+fsid in its devitem.
$ btrfs in dump-super /dev/sdc | egrep '^generation|dev_item.uuid|dev_item.fsid|devid'
generation 20
dev_item.uuid 59368f50-9af2-4b17-91da-8a783cc418d4
dev_item.fsid ab2c88b7-be81-4a7e-9849-c3666e7f9f4f [match]
dev_item.devid 1
So if you provide the original seed device the mount shall be
successful. Which so long happening in the test case btrfs/163.
$ btrfs device scan --forget
$ mount -o device=/dev/sda /dev/sdb /btrfs
Fix in this patch:
If a seed is not sprouted then there is no replacement of it, because of
its read-only filesystem with a read-only device. Similarly, in the case
of a sprouted filesystem, the seed device is still read only. So, mark
it as you can't replace a seed device, you can only add a new device and
then delete the seed device. If replace is attempted then returns
-EINVAL.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of using a flag bit for exclusive operation, use a variable to
store which exclusive operation is being performed. Introduce an API
to start and finish an exclusive operation.
This would enable another way for tools to check which operation is
running on why starting an exclusive operation failed. The followup
patch adds a sysfs_notify() to alert userspace when the state changes, so
userspace can perform select() on it to get notified of the change.
This would enable us to enqueue a command which will wait for current
exclusive operation to complete before issuing the next exclusive
operation. This has been done synchronously as opposed to a background
process, or else error collection (if any) will become difficult.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
We have btrfs_wait_ordered_roots() which takes a u64 for nr, but
btrfs_start_delalloc_roots() that takes an int for nr, which makes using
them in conjunction, especially for something like (u64)-1, annoying and
inconsistent. Fix btrfs_start_delalloc_roots() to take a u64 for nr and
adjust start_delalloc_inodes() and it's callers appropriately.
This means we've adjusted start_delalloc_inodes() to take a pointer of
nr since we want to preserve the ability for start-delalloc_inodes() to
return an error, so simply make it do the nr adjusting as necessary.
Part of adjusting the callers to this means changing
btrfs_writeback_inodes_sb_nr() to take a u64 for items. This may be
confusing because it seems unrelated, but the caller of
btrfs_writeback_inodes_sb_nr() already passes in a u64, it's just the
function variable that needs to be changed.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Tested-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We use a device's allocation state tree to track ranges in a device used
for allocated chunks, and we set ranges in this tree when allocating a new
chunk. However after a device replace operation, we were not setting the
allocated ranges in the new device's allocation state tree, so that tree
is empty after a device replace.
This means that a fitrim operation after a device replace will trim the
device ranges that have allocated chunks and extents, as we trim every
range for which there is not a range marked in the device's allocation
state tree. It is also important during chunk allocation, since the
device's allocation state is used to determine if a range is already
allocated when allocating a new chunk.
This is trivial to reproduce and the following script triggers the bug:
$ cat reproducer.sh
#!/bin/bash
DEV1="/dev/sdg"
DEV2="/dev/sdh"
DEV3="/dev/sdi"
wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null
# Create a raid1 test fs on 2 devices.
mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null
mount $DEV1 /mnt/btrfs
xfs_io -f -c "pwrite -S 0xab 0 10M" /mnt/btrfs/foo
echo "Starting to replace $DEV1 with $DEV3"
btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs
echo
echo "Running fstrim"
fstrim /mnt/btrfs
echo
echo "Unmounting filesystem"
umount /mnt/btrfs
echo "Mounting filesystem in degraded mode using $DEV3 only"
wipefs -a $DEV1 $DEV2 &> /dev/null
mount -o degraded $DEV3 /mnt/btrfs
if [ $? -ne 0 ]; then
dmesg | tail
echo
echo "Failed to mount in degraded mode"
exit 1
fi
echo
echo "File foo data (expected all bytes = 0xab):"
od -A d -t x1 /mnt/btrfs/foo
umount /mnt/btrfs
When running the reproducer:
$ ./replace-test.sh
wrote 10485760/10485760 bytes at offset 0
10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec)
Starting to replace /dev/sdg with /dev/sdi
Running fstrim
Unmounting filesystem
Mounting filesystem in degraded mode using /dev/sdi only
mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error.
[19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started
[19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished
[19582.208293] BTRFS info (device sdi): allowing degraded mounts
[19582.208298] BTRFS info (device sdi): disk space caching is enabled
[19582.208301] BTRFS info (device sdi): has skinny extents
[19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing
[19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed
[19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0
[19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5
[19582.231576] BTRFS error (device sdi): open_ctree failed
Failed to mount in degraded mode
So fix by setting all allocated ranges in the replace target device when
the replace operation is finishing, when we are holding the chunk mutex
and we can not race with new chunk allocations.
A test case for fstests follows soon.
Fixes: 1c11b63eff ("btrfs: replace pending/pinned chunks lists with io tree")
CC: stable@vger.kernel.org # 5.2+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We need to move the closing of the src_device out of all the device
replace locking, but we definitely want to zero out the superblock
before we commit the last time to make sure the device is properly
removed. Handle this by pushing btrfs_scratch_superblocks into
btrfs_dev_replace_finishing, and then later on we'll move the src_device
closing and freeing stuff where we need it to be.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit 668e48af7a ("btrfs: sysfs, add devid/dev_state kobject and
device attributes"), the functions btrfs_sysfs_add_device_link() and
btrfs_sysfs_rm_device_link() do more than just adding and removing the
device link as its name indicated. Rename them to be more specific
that's about the directory with the attirbutes
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The overview of btrfs dev-replace. It mentions some corner cases caused
by the write duplication and scrub based data copy.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ adjust wording ]
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=4OkE
-----END PGP SIGNATURE-----
Merge tag 'for-5.6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"Features, highlights:
- async discard
- "mount -o discard=async" to enable it
- freed extents are not discarded immediatelly, but grouped
together and trimmed later, with IO rate limiting
- the "sync" mode submits short extents that could have been
ignored completely by the device, for SATA prior to 3.1 the
requests are unqueued and have a big impact on performance
- the actual discard IO requests have been moved out of
transaction commit to a worker thread, improving commit latency
- IO rate and request size can be tuned by sysfs files, for now
enabled only with CONFIG_BTRFS_DEBUG as we might need to
add/delete the files and don't have a stable-ish ABI for
general use, defaults are conservative
- export device state info in sysfs, eg. missing, writeable
- no discard of extents known to be untouched on disk (eg. after
reservation)
- device stats reset is logged with process name and PID that called
the ioctl
Fixes:
- fix missing hole after hole punching and fsync when using NO_HOLES
- writeback: range cyclic mode could miss some dirty pages and lead
to OOM
- two more corner cases for metadata_uuid change after power loss
during the change
- fix infinite loop during fsync after mix of rename operations
Core changes:
- qgroup assign returns ENOTCONN when quotas not enabled, used to
return EINVAL that was confusing
- device closing does not need to allocate memory anymore
- snapshot aware code got removed, disabled for years due to
performance problems, reimplmentation will allow to select wheter
defrag breaks or does not break COW on shared extents
- tree-checker:
- check leaf chunk item size, cross check against number of
stripes
- verify location keys for DIR_ITEM, DIR_INDEX and XATTR items
- new self test for physical -> logical mapping code, used for super
block range exclusion
- assertion helpers/macros updated to avoid objtool "unreachable
code" reports on older compilers or config option combinations"
* tag 'for-5.6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (84 commits)
btrfs: free block groups after free'ing fs trees
btrfs: Fix split-brain handling when changing FSID to metadata uuid
btrfs: Handle another split brain scenario with metadata uuid feature
btrfs: Factor out metadata_uuid code from find_fsid.
btrfs: Call find_fsid from find_fsid_inprogress
Btrfs: fix infinite loop during fsync after rename operations
btrfs: set trans->drity in btrfs_commit_transaction
btrfs: drop log root for dropped roots
btrfs: sysfs, add devid/dev_state kobject and device attributes
btrfs: Refactor btrfs_rmap_block to improve readability
btrfs: Add self-tests for btrfs_rmap_block
btrfs: selftests: Add support for dummy devices
btrfs: Move and unexport btrfs_rmap_block
btrfs: separate definition of assertion failure handlers
btrfs: device stats, log when stats are zeroed
btrfs: fix improper setting of scanned for range cyclic write cache pages
btrfs: safely advance counter when looking up bio csums
btrfs: remove unused member btrfs_device::work
btrfs: remove unnecessary wrapper get_alloc_profile
btrfs: add correction to handle -1 edge case in async discard
...
The fstests btrfs/011 triggered a warning at the end of device replace,
[ 1891.998975] BTRFS warning (device vdd): failed setting block group ro: -28
[ 1892.038338] BTRFS error (device vdd): btrfs_scrub_dev(/dev/vdd, 1, /dev/vdb) failed -28
[ 1892.059993] ------------[ cut here ]------------
[ 1892.063032] WARNING: CPU: 2 PID: 2244 at fs/btrfs/dev-replace.c:506 btrfs_dev_replace_start.cold+0xf9/0x140 [btrfs]
[ 1892.074346] CPU: 2 PID: 2244 Comm: btrfs Not tainted 5.5.0-rc7-default+ #942
[ 1892.079956] RIP: 0010:btrfs_dev_replace_start.cold+0xf9/0x140 [btrfs]
[ 1892.096576] RSP: 0018:ffffbb58c7b3fd10 EFLAGS: 00010286
[ 1892.098311] RAX: 00000000ffffffe4 RBX: 0000000000000001 RCX: 8888888888888889
[ 1892.100342] RDX: 0000000000000001 RSI: ffff9e889645f5d8 RDI: ffffffff92821080
[ 1892.102291] RBP: ffff9e889645c000 R08: 000001b8878fe1f6 R09: 0000000000000000
[ 1892.104239] R10: ffffbb58c7b3fd08 R11: 0000000000000000 R12: ffff9e88a0017000
[ 1892.106434] R13: ffff9e889645f608 R14: ffff9e88794e1000 R15: ffff9e88a07b5200
[ 1892.108642] FS: 00007fcaed3f18c0(0000) GS:ffff9e88bda00000(0000) knlGS:0000000000000000
[ 1892.111558] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1892.113492] CR2: 00007f52509ff420 CR3: 00000000603dd002 CR4: 0000000000160ee0
[ 1892.115814] Call Trace:
[ 1892.116896] btrfs_dev_replace_by_ioctl+0x35/0x60 [btrfs]
[ 1892.118962] btrfs_ioctl+0x1d62/0x2550 [btrfs]
caused by the previous patch ("btrfs: scrub: Require mandatory block
group RO for dev-replace"). Hitting ENOSPC is possible and could happen
when the block group is set read-only, preventing NOCOW writes to the
area that's being accessed by dev-replace.
This has happend with scratch devices of size 12G but not with 5G and
20G, so this is depends on timing and other activity on the filesystem.
The whole replace operation is restartable, the space state should be
examined by the user in any case.
The error code is propagated back to the ioctl caller so the kernel
warning is causing false alerts.
Signed-off-by: David Sterba <dsterba@suse.com>
New sysfs attributes that track the filesystem status of devices, stored
in the per-filesystem directory in /sys/fs/btrfs/FSID/devinfo . There's
a directory for each device, with name corresponding to the numerical
device id.
in_fs_metadata - device is in the list of fs metadata
missing - device is missing (no device node or block device)
replace_target - device is target of replace
writeable - writes from fs are allowed
These attributes reflect the state of the device::dev_state and created
at mount time.
Sample output:
$ pwd
/sys/fs/btrfs/6e1961f1-5918-4ecc-a22f-948897b409f7/devinfo/1/
$ ls
in_fs_metadata missing replace_target writeable
$ cat missing
0
The output from these attributes are 0 or 1. 0 indicates unset and 1
indicates set. These attributes are readonly.
It is observed that the device delete thread and sysfs read thread will
not race because the delete thread calls sysfs kobject_put() which in
turn waits for existing sysfs read to complete.
Note for device replace devid swap:
During the replace the target device temporarily assumes devid 0 before
assigning the devid of the soruce device.
In btrfs_dev_replace_finishing() we remove source sysfs devid using the
function btrfs_sysfs_remove_devices_attr(), so after that call
kobject_rename() to update the devid in the sysfs. This adds and calls
btrfs_sysfs_update_devid() helper function to update the device id.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
The attribute is more relaxed than const and the functions could
dereference pointers, as long as the observable state is not changed. We
do have such functions, based on -Wsuggest-attribute=pure .
The visible effects of this patch are negligible, there are differences
in the assembly but hard to summarize.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The file ctree.h serves as a header for everything and has become quite
bloated. Split some helpers that are generic and create a new file that
should be the catch-all for code that's not btrfs-specific.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
The BTRFS_DEV_REPLACE_ITEM_STATE_x defines, as shown in [1], are
unused in both kernel and btrfs-progs (except for one instance of
BTRFS_DEV_REPLACE_ITEM_STATE_NEVER_STARTED in kernel).
[1]
btrfs.h:#define BTRFS_IOCTL_DEV_REPLACE_STATE_FINISHED 2
btrfs.h:#define BTRFS_IOCTL_DEV_REPLACE_STATE_CANCELED 3
btrfs.h:#define BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED 4
Further these define-values are different form its counterpart
BTRFS_IOCTL_DEV_REPLACE_STATE_x series as shown in [2].
[2]
btrfs_tree.h:#define BTRFS_DEV_REPLACE_ITEM_STATE_SUSPENDED 2
btrfs_tree.h:#define BTRFS_DEV_REPLACE_ITEM_STATE_FINISHED 3
btrfs_tree.h:#define BTRFS_DEV_REPLACE_ITEM_STATE_CANCELED 4
So this patch deletes the BTRFS_DEV_REPLACE_ITEM_STATE_x altogether, and
one instance of BTRFS_DEV_REPLACE_ITEM_STATE_NEVER_STARTED is replaced
with BTRFS_IOCTL_DEV_REPLACE_STATE_NEVER_STARTED in the kernel.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
fs_info::mapping_tree is the physical<->logical mapping tree and uses
the same underlying structure as extents, but is embedded to another
structure. There are no other members and this indirection is useless.
No functional change.
Signed-off-by: David Sterba <dsterba@suse.com>
This is already done in btrfs_init_dev_replace_tgtdev which is the first
phase of device replace, called before doing scrub. During that time
exclusive lock is held. Additionally btrfs_fs_device::commit_total_bytes
is always set based on the size of the underlying block device which
shouldn't change once set. This makes the 2nd assignment of the variable
in the finishing phase redundant.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Part of device replace involves writing an item to the device root
containing information about pending replace operations. Currently space
for this item is not being explicitly reserved so this works thanks to
presence of global reserve. While not fatal it's not a good practice.
Let's be explicit about space requirement of device replace and reserve
space when starting the transaction.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are only 2 branches which goto leave label with need_unlock set
to true. Essentially need_unlock is used as a substitute for directly
calling up_write. Since the branches needing this are only 2 and their
context is not that big it's more clear to just call up_write where
required. No functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_init_dev_replace_tgtdev reads certain values from the source
device (such as commit_total_bytes) which are updated during transaction
commit. Currently this function is called before committing any pending
transaction, leading to possibly reading outdated values.
Fix this by moving the function below the transaction commit, at this
point the EXCL_OP bit it set hence once transaction is complete the
total size of the device cannot be changed (it's usually changed by
resize/remove ops which are blocked).
Fixes: 9e271ae27e ("Btrfs: kernel operation should come after user input has been verified")
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This WARN_ON can never trigger because src_device cannot be null.
btrfs_find_device_by_devspec always returns either an error or a valid
pointer to the device. Just remove it.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is no point in holding btrfs_fs_devices::device_list_mutex
while initialising fields of the not-yet-published device. Instead,
hold the mutex only when the newly initialised device is being
published. I think holding device_list_mutex here is redundant
altogether, because at this point BTRFS_FS_EXCL_OP is set which
prevents device removal/addition/balance/resize to occur.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Using sync_blockdev makes it plain obvious what's happening. No
functional changes.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Recent FITRIM work, namely bbbf7243d6 ("btrfs: combine device update
operations during transaction commit") combined the way certain
operations are recoded in a transaction. As a result an ASSERT was added
in dev_replace_finish to ensure the new code works correctly.
Unfortunately I got reports that it's possible to trigger the assert,
meaning that during a device replace it's possible to have an unfinished
chunk allocation on the source device.
This is supposed to be prevented by the fact that a transaction is
committed before finishing the replace oepration and alter acquiring the
chunk mutex. This is not sufficient since by the time the transaction is
committed and the chunk mutex acquired it's possible to allocate a chunk
depending on the workload being executed on the replaced device. This
bug has been present ever since device replace was introduced but there
was never code which checks for it.
The correct way to fix is to ensure that there is no pending device
modification operation when the chunk mutex is acquire and if there is
repeat transaction commit. Unfortunately it's not possible to just
exclude the source device from btrfs_fs_devices::dev_alloc_list since
this causes ENOSPC to be hit in transaction commit.
Fixing that in another way would need to add special cases to handle the
last writes and forbid new ones. The looped transaction fix is more
obvious, and can be easily backported. The runtime of dev-replace is
long so there's no noticeable delay caused by that.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: 391cd9df81 ("Btrfs: fix unprotected alloc list insertion during the finishing procedure of replace")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We currently overload the pending_chunks list to handle updating
btrfs_device->commit_bytes used. We don't actually care about the
extent mapping or even the device mapping for the chunk - we just need
the device, and we can end up processing it multiple times. The
fs_devices->resized_list does more or less the same thing, but with the
disk size. They are called consecutively during commit and have more or
less the same purpose.
We can combine the two lists into a single list that attaches to the
transaction and contains a list of devices that need updating. Since we
always add the device to a list when we change bytes_used or
disk_total_size, there's no harm in copying both values at once.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We should drop the lock on this error path. This has been found by a
static tool.
The lock needs to be released, it's there to protect access to the
dev_replace members and is not supposed to be left locked. The value of
state that's being switched would need to be artifically changed to an
invalid value so the default: branch is taken.
Fixes: d189dd70e2 ("btrfs: fix use-after-free due to race between replace start and cancel")
CC: stable@vger.kernel.org # 5.0+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Both btrfs_find_device() and find_device() does the same thing except
that the latter does not take the seed device onto account in the device
scanning context. We can merge them.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_find_device() accepts fs_info as an argument and retrieves
fs_devices from fs_info.
Instead use fs_devices, so that this function can be used in non-mount
(during device scanning) context as well.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The typos accumulate over time so once in a while time they get fixed in
a large patch.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The dev-replace locking functions are now trivial wrappers around rw
semaphore that can be used directly everywhere. No functional change.
Signed-off-by: David Sterba <dsterba@suse.com>
After the rw semaphore has been added, the custom blocking using
::blocking_readers and ::read_lock_wq is redundant.
The blocking logic in __btrfs_map_block is replaced by extending the
time the semaphore is held, that has the same blocking effect on writes
as the previous custom scheme that waited until ::blocking_readers was
zero.
Signed-off-by: David Sterba <dsterba@suse.com>
This is the first part of removing the custom locking and waiting scheme
used for device replace. It was probably copied from extent buffer
locking, but there's nothing that would require more than is provided by
the common locking primitives.
The rw spinlock protects waiting tasks counter in case of incompatible
locks and the waitqueue. Same as rw semaphore.
This patch only switches the locking primitive, for better
bisectability. There should be no functional change other than the
overhead of the locking and potential sleeping instead of spinning when
the lock is contended.
Signed-off-by: David Sterba <dsterba@suse.com>
As of now only user requested replace cancel can cancel the
replace-scrub so no need to log the error.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we successfully cancel the device replace, its scrub worker returns
-ECANCELED, which is then passed to btrfs_dev_replace_finishing.
It cleans up based on the returned status and propagates the same
-ECANCELED back the parent function. As of now only user can cancel the
replace-scrub, so its ok to silence the warning here.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We recast the replace return status
BTRFS_IOCTL_DEV_REPLACE_RESULT_SCRUB_INPROGRESS to 0, to indicate no
error.
And since BTRFS_IOCTL_DEV_REPLACE_RESULT_NO_ERROR should also return 0,
which is also declared as 0, so we just return. Instead add it to the if
statement so that there is enough clarity while reading the code.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When the replace state is in the suspended state, btrfs_scrub_cancel()
should fail with -ENOTCONN as there is no scrub running. As a safety
catch check if btrfs_scrub_cancel() returns -ENOTCONN and assert if it
doesn't.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The device-replace needs to check the result code of the scrub workers
in btrfs_dev_replace_cancel and distinguish if successful cancel
operation and when the there was no operation running.
If btrfs_scrub_cancel() fails, return
BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try
to cancel the replace again.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
The device replace cancel thread can race with the replace start thread
and if fs_info::scrubs_running is not yet set, btrfs_scrub_cancel() will
fail to stop the scrub thread.
The scrub thread continues with the scrub for replace which then will
try to write to the target device and which is already freed by the
cancel thread.
scrub_setup_ctx() warns as tgtdev is NULL.
struct scrub_ctx *scrub_setup_ctx(struct btrfs_device *dev, int is_dev_replace)
{
...
if (is_dev_replace) {
WARN_ON(!fs_info->dev_replace.tgtdev); <===
sctx->pages_per_wr_bio = SCRUB_PAGES_PER_WR_BIO;
sctx->wr_tgtdev = fs_info->dev_replace.tgtdev;
sctx->flush_all_writes = false;
}
[ 6724.497655] BTRFS info (device sdb): dev_replace from /dev/sdb (devid 1) to /dev/sdc started
[ 6753.945017] BTRFS info (device sdb): dev_replace from /dev/sdb (devid 1) to /dev/sdc canceled
[ 6852.426700] WARNING: CPU: 0 PID: 4494 at fs/btrfs/scrub.c:622 scrub_setup_ctx.isra.19+0x220/0x230 [btrfs]
...
[ 6852.428928] RIP: 0010:scrub_setup_ctx.isra.19+0x220/0x230 [btrfs]
...
[ 6852.432970] Call Trace:
[ 6852.433202] btrfs_scrub_dev+0x19b/0x5c0 [btrfs]
[ 6852.433471] btrfs_dev_replace_start+0x48c/0x6a0 [btrfs]
[ 6852.433800] btrfs_dev_replace_by_ioctl+0x3a/0x60 [btrfs]
[ 6852.434097] btrfs_ioctl+0x2476/0x2d20 [btrfs]
[ 6852.434365] ? do_sigaction+0x7d/0x1e0
[ 6852.434623] do_vfs_ioctl+0xa9/0x6c0
[ 6852.434865] ? syscall_trace_enter+0x1c8/0x310
[ 6852.435124] ? syscall_trace_enter+0x1c8/0x310
[ 6852.435387] ksys_ioctl+0x60/0x90
[ 6852.435663] __x64_sys_ioctl+0x16/0x20
[ 6852.435907] do_syscall_64+0x50/0x180
[ 6852.436150] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Further, as the replace thread enters scrub_write_page_to_dev_replace()
without the target device it panics:
static int scrub_add_page_to_wr_bio(struct scrub_ctx *sctx,
struct scrub_page *spage)
{
...
bio_set_dev(bio, sbio->dev->bdev); <======
[ 6929.715145] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
..
[ 6929.717106] Workqueue: btrfs-scrub btrfs_scrub_helper [btrfs]
[ 6929.717420] RIP: 0010:scrub_write_page_to_dev_replace+0xb4/0x260
[btrfs]
..
[ 6929.721430] Call Trace:
[ 6929.721663] scrub_write_block_to_dev_replace+0x3f/0x60 [btrfs]
[ 6929.721975] scrub_bio_end_io_worker+0x1af/0x490 [btrfs]
[ 6929.722277] normal_work_helper+0xf0/0x4c0 [btrfs]
[ 6929.722552] process_one_work+0x1f4/0x520
[ 6929.722805] ? process_one_work+0x16e/0x520
[ 6929.723063] worker_thread+0x46/0x3d0
[ 6929.723313] kthread+0xf8/0x130
[ 6929.723544] ? process_one_work+0x520/0x520
[ 6929.723800] ? kthread_delayed_work_timer_fn+0x80/0x80
[ 6929.724081] ret_from_fork+0x3a/0x50
Fix this by letting the btrfs_dev_replace_finishing() to do the job of
cleaning after the cancel, including freeing of the target device.
btrfs_dev_replace_finishing() is called when btrfs_scub_dev() returns
along with the scrub return status.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In a secnario where balance and replace co-exists as below,
- start balance
- pause balance
- start replace
- reboot
and when system restarts, balance resumes first. Then the replace is
attempted to restart but will fail as the EXCL_OP lock is already held
by the balance. If so place the replace state back to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state.
Fixes: 010a47bde9 ("btrfs: add proper safety check before resuming dev-replace")
CC: stable@vger.kernel.org # 4.18+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At the time of forced unmount we place the running replace to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state, so when the system comes
back and expect the target device is missing.
Then let the replace state continue to be in
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state instead of
BTRFS_IOCTL_DEV_REPLACE_STATE_STARTED as there isn't any matching scrub
running as part of replace.
Fixes: e93c89c1aa ("Btrfs: add new sources for device replace code")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There isn't any other consumer other than in its own file dev-replace.c.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
dev_replace::replace_state has been set to
BTRFS_DEV_REPLACE_ITEM_STATE_NEVER_STARTED (0) in the same function,
So delete the line which sets replace_state = 0;
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
A later patch will implement swap file support for Btrfs, but before we
do that, we need to make sure that the various Btrfs ioctls cannot
change a swap file.
When a swap file is active, we must make sure that the extents of the
file are not moved and that they don't become shared. That means that
the following are not safe:
- chattr +c (enable compression)
- reflink
- dedupe
- snapshot
- defrag
Don't allow those to happen on an active swap file.
Additionally, balance, resize, device remove, and device replace are
also unsafe if they affect an active swapfile. Add a red-black tree of
block groups and devices which contain an active swapfile. Relocation
checks each block group against this tree and skips it or errors out for
balance or resize, respectively. Device remove and device replace check
the tree for the device they will operate on.
Note that we don't have to worry about chattr -C (disable nocow), which
we ignore for non-empty files, because an active swapfile must be
non-empty and can't be truncated. We also don't have to worry about
autodefrag because it's only done on COW files. Truncate and fallocate
are already taken care of by the generic code. Device add doesn't do
relocation so it's not an issue, either.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The value of blocking_readers is increased only when the lock is taken
for read, no way we can fail the condition with the write lock.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The replace_wait and bio_counter were mistakenly added to fs_info in
commit c404e0dc2c ("Btrfs: fix use-after-free in the finishing
procedure of the device replace"), but they logically belong to
fs_info::dev_replace. Besides, bio_counter is a very generic name and is
confusing in bare fs_info context.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The exit sequence in btrfs_dev_replace_start does not allow to simply
add a label to the right place so the error handling after starting
transaction failure jumps there. Currently there's a lock that pairs
with the unlock in the section, which is unnecessary and only raises
questions. Add a variable to track the locking status and avoid the
extra locking.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Too trivial, the purpose can be simply documented in a comment.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There's a single caller and the function name does not say it's actually
taking the lock, so open coding makes it more explicit.
For now, btrfs_dev_replace_read_lock is used instead of read_lock so
it's paired with the unlocking wrapper in the same block.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This member seems to be copied from the extent_buffer locking scheme and
is at least used to assert that the read lock/unlock is properly nested.
In some way. While the _inc/_dec are called inside the read lock
section, the asserts are both inside and outside, so the ordering is not
guaranteed and we can see read/inc/dec ordered in any way
(theoretically).
A missing call of btrfs_dev_replace_clear_lock_blocking could cause
unexpected read_locks count, so this at least looks like a valid
assertion, but this will become unnecessary with later updates.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we fail to start a transaction in btrfs_dev_replace_start, we leave
dev_replace->replace_start set to STARTED but clear ->srcdev and
->tgtdev. Later, that can result in an Oops in
btrfs_dev_replace_progress when having state set to STARTED or SUSPENDED
implies that ->srcdev is valid.
Also fix error handling when the state is already STARTED or SUSPENDED
while starting. That, too, will clear ->srcdev and ->tgtdev even though
it doesn't own them. This should be an impossible case to hit since we
should be protected by the BTRFS_FS_EXCL_OP bit being set. Let's add an
ASSERT there while we're at it.
Fixes: e93c89c1aa (Btrfs: add new sources for device replace code)
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of returning an error value and using one of the parameters for
returning the actual object we are interested in just refactor the
function to directly return btrfs_device *. Also bubble up the error
handling for the special BTRFS_ERROR_DEV_MISSING_NOT_FOUND value into
btrfs_rm_device. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
on-disk devs stats value is updated in btrfs_run_dev_stats(),
which is called during commit transaction, if device->dev_stats_ccnt
is not zero.
Since current replace operation does not touch dev_stats_ccnt,
on-disk dev stats value is not updated. Therefore "btrfs device stats"
may return old device's value after umount/mount
(Example: See "btrfs ins dump-t -t DEV $DEV" after btrfs/100 finish).
Fix this by just incrementing dev_stats_ccnt in
btrfs_dev_replace_finishing() when replace is succeeded and this will
update the values.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function is always passed a well-formed tgtdevice so the fs_info
can be referenced from there.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the passed 'device' argument which is always
a well-formed device.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It can be referenced from the passed srcdev argument.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The get_seconds() function is deprecated as it truncates the timestamp
to 32 bits. Change it to or ktime_get_real_seconds().
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_dev_replace_finishing updates devices (soruce and target) which
are within the btrfs_fs_devices::devices or withint the cloned seed
devices (btrfs_fs_devices::seed::devices), so we don't need the global
uuid_mutex.
The device replace context is also locked by its own locks.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use the wrappers and reduce the amount of low-level details about the
waitqueue management.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This parameter was introduced alongside the function in
eb73c1b7ce ("Btrfs: introduce per-subvolume delalloc inode list") to
avoid deadlocks since this function was used in the transaction commit
path. However, commit 8d875f95da ("btrfs: disable strict file flushes
for renames and truncates") removed that usage, rendering the parameter
obsolete.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The volume mutex does not protect against anything in this case, the
comment about scrub is right but not related to locking and looks
confusing. The comment in btrfs_find_device_missing_or_by_path is wrong
and confusing too.
The device_list_mutex is not held here to protect device lookup, but in
this case device replace cannot run in parallel with device removal (due
to exclusive op protection), so we don't need further locking here.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The device replace is paused by unmount or read only remount, and
resumed on next mount or write remount.
The exclusive status should be checked properly as it's a global
invariant and we must not allow 2 operations run. In this case, the
balance can be also paused and resumed under same conditions. It's
always checked first so dev-replace could see the EXCL_OP already taken,
BUT, the ioctl would never let start both at the same time.
Replace the WARN_ON with message and return 0, indicating no error as
this is purely theoretical and the user will be informed. Resolving that
manually should be possible by waiting for the other operation to finish
or cancel the paused state.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The function logically belongs there and there's only a single caller,
no need to export it. No code changes.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is a preparatory cleanup that will make clear that the only
successful way out of btrfs_init_dev_replace_tgtdev will also set the
device_out to a valid pointer. With this guarantee, the callers can be
simplified.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The function is called once and is fairly small, we can merge it with
the caller.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Remove GPL boilerplate text (long, short, one-line) and keep the rest,
ie. personal, company or original source copyright statements. Add the
SPDX header.
Signed-off-by: David Sterba <dsterba@suse.com>
The current calls are unclear in what way btrfs_dev_replace_lock takes
the locks, so drop the argument, split the helpers and use similar
naming as for read and write locks.
Signed-off-by: David Sterba <dsterba@suse.com>
For debugging or administration purposes, we would want to know if and
when the user cancels the replace, to complement the existing messages
when dev-replace starts or finishes.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog, fold fix for RCU warning from Nikolay ]
Signed-off-by: David Sterba <dsterba@suse.com>
The replace target device can be missing when mounted with -o degraded,
but we wont allocate a missing btrfs_device to it. So check the device
before accessing.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000b0
IP: btrfs_destroy_dev_replace_tgtdev+0x43/0xf0 [btrfs]
Call Trace:
btrfs_dev_replace_cancel+0x15f/0x180 [btrfs]
btrfs_ioctl+0x2216/0x2590 [btrfs]
do_vfs_ioctl+0x625/0x650
SyS_ioctl+0x4e/0x80
do_syscall_64+0x5d/0x160
entry_SYSCALL64_slow_path+0x25/0x25
This patch has been moved in front of patch "btrfs: log, when replace,
is canceled by the user" that could reproduce the crash if the system
reboots inside btrfs_dev_replace_start before the
btrfs_dev_replace_finishing call.
$ mkfs /dev/sda
$ mount /dev/sda mnt
$ btrfs replace start /dev/sda /dev/sdb
<insert reboot>
$ mount po degraded /dev/sdb mnt
<crash>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
[ added reproducer description from mail ]
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_init_dev_replace_tgtdev_for_resume() initializes replace
target device in a few simple steps, so do it at the parent function.
Moreover, there isn't any other caller so just open code it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Current u64 return from btrfs_dev_replace_cancel() was probably done
to match the btrfs_ioctl_dev_replace_args::result. However as our
actual return value fits in int, and it further gets typecast to u64,
so just return int.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Remove __ which is for the special functions.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_dev_replace_cancel() calls __btrfs_dev_replace_cancel() for the
actual cancel so just open code it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently device state is being managed by each individual int
variable such as struct btrfs_device::is_tgtdev_for_dev_replace.
Instead of that declare btrfs_device::dev_state
BTRFS_DEV_STATE_MISSING and use the bit operations.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
[ whitespace adjustments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Currently device state is being managed by each individual int
variable such as struct btrfs_device::missing. Instead of that
declare btrfs_device::dev_state BTRFS_DEV_STATE_MISSING and use
the bit operations.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by : Nikolay Borisov <nborisov@suse.com>
[ whitespace adjustments ]
Signed-off-by: David Sterba <dsterba@suse.com>
This patch creates a helper function to get either the rcu device path
or missing.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
[ rename to btrfs_dev_name, switch to if/else ]
Signed-off-by: David Sterba <dsterba@suse.com>
Pull mount flag updates from Al Viro:
"Another chunk of fmount preparations from dhowells; only trivial
conflicts for that part. It separates MS_... bits (very grotty
mount(2) ABI) from the struct super_block ->s_flags (kernel-internal,
only a small subset of MS_... stuff).
This does *not* convert the filesystems to new constants; only the
infrastructure is done here. The next step in that series is where the
conflicts would be; that's the conversion of filesystems. It's purely
mechanical and it's better done after the merge, so if you could run
something like
list=$(for i in MS_RDONLY MS_NOSUID MS_NODEV MS_NOEXEC MS_SYNCHRONOUS MS_MANDLOCK MS_DIRSYNC MS_NOATIME MS_NODIRATIME MS_SILENT MS_POSIXACL MS_KERNMOUNT MS_I_VERSION MS_LAZYTIME; do git grep -l $i fs drivers/staging/lustre drivers/mtd ipc mm include/linux; done|sort|uniq|grep -v '^fs/namespace.c$')
sed -i -e 's/\<MS_RDONLY\>/SB_RDONLY/g' \
-e 's/\<MS_NOSUID\>/SB_NOSUID/g' \
-e 's/\<MS_NODEV\>/SB_NODEV/g' \
-e 's/\<MS_NOEXEC\>/SB_NOEXEC/g' \
-e 's/\<MS_SYNCHRONOUS\>/SB_SYNCHRONOUS/g' \
-e 's/\<MS_MANDLOCK\>/SB_MANDLOCK/g' \
-e 's/\<MS_DIRSYNC\>/SB_DIRSYNC/g' \
-e 's/\<MS_NOATIME\>/SB_NOATIME/g' \
-e 's/\<MS_NODIRATIME\>/SB_NODIRATIME/g' \
-e 's/\<MS_SILENT\>/SB_SILENT/g' \
-e 's/\<MS_POSIXACL\>/SB_POSIXACL/g' \
-e 's/\<MS_KERNMOUNT\>/SB_KERNMOUNT/g' \
-e 's/\<MS_I_VERSION\>/SB_I_VERSION/g' \
-e 's/\<MS_LAZYTIME\>/SB_LAZYTIME/g' \
$list
and commit it with something along the lines of 'convert filesystems
away from use of MS_... constants' as commit message, it would save a
quite a bit of headache next cycle"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Differentiate mount flags (MS_*) from internal superblock flags
VFS: Convert sb->s_flags & MS_RDONLY to sb_rdonly(sb)
vfs: Add sb_rdonly(sb) to query the MS_RDONLY flag on s_flags
This function prints an informative message and then continues
dev-replace. The message contains a progress percentage which is read
from the status. The status is allocated dynamically, about 2600 bytes,
just to read the single value. That's an overkill. We'll use the new
helper and drop the allocation.
Signed-off-by: David Sterba <dsterba@suse.com>
We'll want to read the percentage value from dev_replace elsewhere, move
the logic to a separate helper.
Signed-off-by: David Sterba <dsterba@suse.com>
Firstly by applying the following with coccinelle's spatch:
@@ expression SB; @@
-SB->s_flags & MS_RDONLY
+sb_rdonly(SB)
to effect the conversion to sb_rdonly(sb), then by applying:
@@ expression A, SB; @@
(
-(!sb_rdonly(SB)) && A
+!sb_rdonly(SB) && A
|
-A != (sb_rdonly(SB))
+A != sb_rdonly(SB)
|
-A == (sb_rdonly(SB))
+A == sb_rdonly(SB)
|
-!(sb_rdonly(SB))
+!sb_rdonly(SB)
|
-A && (sb_rdonly(SB))
+A && sb_rdonly(SB)
|
-A || (sb_rdonly(SB))
+A || sb_rdonly(SB)
|
-(sb_rdonly(SB)) != A
+sb_rdonly(SB) != A
|
-(sb_rdonly(SB)) == A
+sb_rdonly(SB) == A
|
-(sb_rdonly(SB)) && A
+sb_rdonly(SB) && A
|
-(sb_rdonly(SB)) || A
+sb_rdonly(SB) || A
)
@@ expression A, B, SB; @@
(
-(sb_rdonly(SB)) ? 1 : 0
+sb_rdonly(SB)
|
-(sb_rdonly(SB)) ? A : B
+sb_rdonly(SB) ? A : B
)
to remove left over excess bracketage and finally by applying:
@@ expression A, SB; @@
(
-(A & MS_RDONLY) != sb_rdonly(SB)
+(bool)(A & MS_RDONLY) != sb_rdonly(SB)
|
-(A & MS_RDONLY) == sb_rdonly(SB)
+(bool)(A & MS_RDONLY) == sb_rdonly(SB)
)
to make comparisons against the result of sb_rdonly() (which is a bool)
work correctly.
Signed-off-by: David Howells <dhowells@redhat.com>
Dave Jones hit a WARN_ON(nr < 0) in btrfs_wait_ordered_roots() with
v4.12-rc6. This was because commit 70e7af244 made it possible for
calc_reclaim_items_nr() to return a negative number. It's not really a
bug in that commit, it just didn't go far enough down the stack to find
all the possible 64->32 bit overflows.
This switches calc_reclaim_items_nr() to return a u64 and changes everyone
that uses the results of that math to u64 as well.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 70e7af2 ("Btrfs: fix delalloc accounting leak caused by u32 overflow")
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is fixing code pieces where we use div_u64 when passing a u64 divisor.
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When raid56 dev-replace is cancelled by running scrub, we will free
target device without waiting for in-flight bios, causing the following
NULL pointer deference or general protection failure.
BUG: unable to handle kernel NULL pointer dereference at 00000000000005e0
IP: generic_make_request_checks+0x4d/0x610
CPU: 1 PID: 11676 Comm: kworker/u4:14 Tainted: G O 4.11.0-rc2 #72
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-20170228_101828-anatol 04/01/2014
Workqueue: btrfs-endio-raid56 btrfs_endio_raid56_helper [btrfs]
task: ffff88002875b4c0 task.stack: ffffc90001334000
RIP: 0010:generic_make_request_checks+0x4d/0x610
Call Trace:
? generic_make_request+0xc7/0x360
generic_make_request+0x24/0x360
? generic_make_request+0xc7/0x360
submit_bio+0x64/0x120
? page_in_rbio+0x4d/0x80 [btrfs]
? rbio_orig_end_io+0x80/0x80 [btrfs]
finish_rmw+0x3f4/0x540 [btrfs]
validate_rbio_for_rmw+0x36/0x40 [btrfs]
raid_rmw_end_io+0x7a/0x90 [btrfs]
bio_endio+0x56/0x60
end_workqueue_fn+0x3c/0x40 [btrfs]
btrfs_scrubparity_helper+0xef/0x620 [btrfs]
btrfs_endio_raid56_helper+0xe/0x10 [btrfs]
process_one_work+0x2af/0x720
? process_one_work+0x22b/0x720
worker_thread+0x4b/0x4f0
kthread+0x10f/0x150
? process_one_work+0x720/0x720
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x2e/0x40
RIP: generic_make_request_checks+0x4d/0x610 RSP: ffffc90001337bb8
In btrfs_dev_replace_finishing(), we will call
btrfs_rm_dev_replace_blocked() to wait bios before destroying the target
device when scrub is finished normally.
However when dev-replace is aborted, either due to error or cancelled by
scrub, we didn't wait for bios, this can lead to use-after-free if there
are bios holding the target device.
Furthermore, for raid56 scrub, at least 2 places are calling
btrfs_map_sblock() without protection of bio_counter, leading to the
problem.
This patch fixes the problem:
1) Wait for bio_counter before freeing target device when canceling
replace
2) When calling btrfs_map_sblock() for raid56, use bio_counter to
protect the call.
Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are several operations, usually started from ioctls, that cannot
run concurrently. The status is tracked in
mutually_exclusive_operation_running as an atomic_t. We can easily track
the status as one of the per-filesystem flag bits with same
synchronization guarantees.
The conversion replaces:
* atomic_xchg(..., 1) -> test_and_set_bit(FLAG, ...)
* atomic_set(..., 0) -> clear_bit(FLAG, ...)
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now we only use the root parameter to print the root objectid in
a tracepoint. We can use the root parameter from the transaction
handle for that. It's also used to join the transaction with
async commits, so we remove the comment that it's just for checking.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are loads of functions in btrfs that accept a root parameter
but only use it to obtain an fs_info pointer. Let's convert those to
just accept an fs_info pointer directly.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In routines where someptr->fs_info is referenced multiple times, we
introduce a convenience variable. This makes the code considerably
more readable.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For many printks, we want to know which file system issued the message.
This patch converts most pr_* calls to use the btrfs_* versions instead.
In some cases, this means adding plumbing to allow call sites access to
an fs_info pointer.
fs/btrfs/check-integrity.c is left alone for another day.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
CodingStyle chapter 2:
"[...] never break user-visible strings such as printk messages,
because that breaks the ability to grep for them."
This patch unsplits user-visible strings.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_test_opt and friends only use the root pointer to access
the fs_info. Let's pass the fs_info directly in preparation to
eliminate similar patterns all over btrfs.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
