An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The upper limit of Tx/Rx FIFO size is 64 word by the
specification of H/W. This patch corrects to 64 word from 256 word.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add SPI Master controller driver for the SPI interface on XLP8XX,
XLP3XX, XLP2XX, XLP9XX and XLP5XX family of Netlogic XLP MIPS64 processors.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM and use autosuspend instead of suspending the
SPI controller after each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that most cleanup is done automatically the remove functions
can be significantly simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrate fsl-espi and fsl-spi to using the managed devm_ functions
for resource handling. This simplifies the cleanup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable pause interrupt should use SPI_CMD_PAUSE_IE MACRO,
so fix it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces *_time name in mtk_spi_prepare_transfer().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch replaces int with u32, deletes TAB, and defines
MTK_SPI_PAUSE_INT_STATUS marco.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mediatek spi driver uses readl/writel, so add linux/io.h,
even so it's implicitly imported by spi/spi.h
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for dual read/writes on spi-bcm63xx-hsspi. This has been
tested with a s25fl129p1 dual read capable spi flash, with a nice speed
improvement:
serial read:
root@OpenWrt:/# time dd if=/dev/mtd4 of=/dev/null bs=8192
2032+0 records in
2032+0 records out
real 0m 4.39s
user 0m 0.00s
sys 0m 1.55s
dual read:
root@OpenWrt:/# time dd if=/dev/mtd4 of=/dev/null bs=8192
2032+0 records in
2032+0 records out
real 0m 3.09s
user 0m 0.00s
sys 0m 1.56s
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit
accesses") changed all 16bit accesses in the DW_apb_ssi driver to 32bit.
This, unfortunately, breaks data register access on picoXcell, where the
DW IP needs data register accesses to be word accesses (all other
accesses appear to be OK).
This change introduces a new master variable to allow interface drivers
to specify that 16bit data transfer I/O is required. This change also
introduces the ability to set this variable via device tree bindings in
the MMIO interface driver. Both the core and the MMIO interface driver
default to the current 32bit behaviour.
Before this change, on a picoXcell pc3x3:
spi_master spi32766: interrupt_transfer: fifo overrun/underrun
m25p80 spi32766.0: error -5 reading 9f
m25p80: probe of spi32766.0 failed with error -5
After this change:
m25p80 spi32766.0: m25p40 (512 Kbytes)
Fixes: dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit accesses")
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a slave appears with no maximum transfer speed specified fall back to
using the maximum for the master instead. It's questionable if we
should let slaves do this but let's be defensive.
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes SPI_CMD_*_OFFSET defines, and uses the BIT(x)
defines instead.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TX_ENDIAN/RX_ENDIAN bits define whether to reverse the endian
order of the data DMA from/to memory. The endian order should
keep the same with cpu endian.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TI QSPI has four 32 bit data regsiters which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with spi-nor flash,
make use of all the four registers so that 16 bytes can be transferred
in one go. This reduces number of register writes and Word Complete
interrupts for a given transfer message size, thereby increasing the
write performance.
Without this patch the raw flash write speed is ~100KB/s, with this
patch the write speed increases to ~400 kB/s on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clock in prepare_hardware/unprepare_hardware is redundant
with pm_runtime, so remove them.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACK of an inexistent IRQ can trigger an spurious IRQ that breaks the
txrx logic. This has been observed on axi_quad_spi:3.2 core.
This patch only ACKs IRQs that have not been Acknowledge jet.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Tested-by: Edward Kigwana <ekigwana@scires.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
writel() already does a cpu_to_le32 conversion, so
remove cpu_to_le32().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once the module process a transfer in irq mode, the next poll transfer
will not work because the transmitter is left in inhibited state.
Fixes: 22417352f6 (Use polling mode on small transfers)
Reported-by: Edward Kigwana <ekigwana@scires.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Description:
On Armada 38x, the device SPI interface supports frequencies of up to
50 MHz. However, due to this erratum, when the device core clock is
250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1, there might occur data corruption on reads from the SPI
device.
Workaround:
Work in one of the following configurations:
1. Set CPOL=CPHA=0 in "SPI Interface Configuration Register".
2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1 Register"
before setting the interface.
[gregory.clement@free-electrons.com}: port to v4.2-rc, use
is_errata_50mhz_ac instead of using a new ARMADA_380_SPI spi type.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch fixes endian warnings detected by sparse:
- sparse: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] val
got restricted __le32 [usertype] <noident>
- sparse: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] val
got restricted __le32 [usertype] <noident>
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extra space and make the alias matches driver name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-img-spfi.c: In function 'img_spfi_setup':
drivers/spi/spi-img-spfi.c:446: warning: 'ret' may be used
uninitialized in this function.
Fixes: commit b03ba9e314 ("spi: img-spfi: fix multiple calls to request gpio")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Remove null_dma_buf variable and extra allocation for it. It is not needed
since commit 6356437e65 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spfi_setup may be called many times by the spi framework, but
gpio_request_one can only be called once without freeing, repeatedly
calling gpio_request_one will cause an error to be thrown, which
causes the request to spi_setup to be marked as failed.
We can have a per-spi_device flag that indicates whether or not the
gpio has been requested. If the gpio has already been requested use
gpio_direction_output to set the direction of the gpio.
Fixes: 8c2c8c03cd ("spi: img-spfi: Control CS lines with GPIO")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fix inconsistent indenting in spidev_open, no functional change.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These became unused by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Major difference in LPSS SPI between Intel Sunrisepoint PCH and earlier
platforms is an integrated DMA (iDMA) engine. iDMA is an IP that is private
for each LPSS host controller (UART/SPI/I2C). Other differences are private
register space offset, a few private registers that are in different
location and FIFO thresholds.
Intel Sunrisepoint LPSS SPI and iDMA devices are probed and registered in
MFD layer as platform devices. Here these compound devices are detected by
matching against known PCI IDs. This allows us to share
pxa2xx_spi_acpi_get_pdata() for setting up the platform data instead of
duplicating it in MFD part.
This patch adds configuration for Intel Sunrisepoint LPSS SPI, above
detection and DMA filter function that picks the DMA channel only from an
associated iDMA block.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This resulted in the use of polling mode when other approaches
(dma or interrupts) would have been more appropriate.
Happened for transfers longer than 477 bytes.
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
