The attached patch updates the driver for the 3ware 9000 series to do
the following:
- Correctly handle single sgl's with use_sg = 1.
This is needed with the latest scsi-block-2.6 merge otherwise the 3w-9xxx
driver will not work. I tested the patch James sent a few weeks back to fix
this, and it had a bug where the request_buffer was accessed in
twa_scsiop_execute_scsi_complete() when it was invalid. This is a corrected
variation of that patch.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS transport class contains common code to deal with SAS HBAs, an
aproximated representation of SAS topologies in the driver model,
and various sysfs attributes to expose these topologies and managment
interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces
two additional intermediate objects: The SAS PHY as represented by struct
sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS
remote PHY represented by struct sas_rphy defines an "incoming" PHY on a
SAS Expander or end device. Note that this is purely a software concept, the
underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs
form a wide port based on the port_identifier attribute, which is the same
for all PHYs in a port.
This submission doesn't handle hot-plug addition or removal of SAS devices
and thus doesn't do scanning in a workqueue yet, that will be added in
phase2 after this submission. In a third phase I will add additional
managment infrastructure.
I think this submission is ready for 2.6.14, but additional comments are
of course very welcome.
I'd like to thanks James Smart a lot for his very useful input on the
design.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The soon to be released smartmontools 5.34 uses the
READ DEFECT DATA command on SCSI disks. A disk that
has defect list entries (or worse, an increasing number
of them) is at risk.
Currently the first invocation of smartctl causes this:
scsi: unknown opcode 0x37
message to appear the console and in the log.
The READ DEFECT DATA SCSI command does not change
the state of a disk. Its opcode (0x37) is valid for
SBC devices (e.g. disks) and SMC-2 devices (media
changers) where it is called INITIALIZE STATUS ELEMENT
WITH RANGE and again doesn't change the external state
of the device.
Changelog:
- mark SCSI opcode 0x37 (READ DEFECT DATA) as
safe_for_read
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Further to the problem discussed in this post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=112540053711489&w=2
It seems that the sg driver does not need to set the VM_IO flag
on pages that it memory maps to the user space since they are
not from the IO space. Ahmed Teirelbar <ahmed.teirelbar@adic.com>
wants the facility and has tested this patch as I have without
adverse effects.
The oops protection is still important. Some users really did
try and use dio transfers from the sg driver to memory mapped
IO space (on a video capture card if my memory serves) during the
lk 2.4 series. I'm not sure how successful it was but that will
now be politely refused in lk 2.6.13+ .
Changelog:
- set the page flags for sg's reserved buffer mmap-ed
to the user space to VM_RESERVED (rather than
VM_RESERVED | VM_IO )
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Actually, just one problem and one cosmetic fix:
1) We need to dequeue for the loop and kill case (it seems easiest
simply to dequeue in the scsi_kill_request() routine)
2) There's no real need to drop the queue lock. __scsi_done() is lock
agnostic, so since there's no requirement, let's just leave it in to
avoid any locking issues.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Alan Stern <stern@rowland.harvard.edu>
This patch (as559b) adds a new routine, scsi_unprep_request, which
gets called every place a request is requeued. (That includes
scsi_queue_insert as well as scsi_requeue_command.) It also changes
scsi_kill_requests to make it call __scsi_done with result equal to
DID_NO_CONNECT << 16. (I'm not sure if it's necessary to call
scsi_init_cmd_errh here; maybe you can check on that.) Finally, the
patch changes the return value from scsi_end_request, to avoid
returning a stale pointer in the case where the request was requeued.
Fortunately the return value is used in only place, and the change
actually simplified it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a filesystem, while writing out data, decides that it is good
to issue a cache flush on a SCSI drive (or other 'sd' device), it will
call blkdev_issue_flush which calls ->issue_flush_fn which is
scsi_issue_flush_fn.
This calls sd_issue_flush which calls sd_sync_cache, which calls
scsi_execute_request.
This will (as sshdr != NULL) call
kmalloc(SCSI_SENSE_BUFFERSIZE, GFP_KERNEL)
If memory is tight, the presence of GFP_KERNEL may cause write
requests to be sent to some filesystem to free up memory, however if
that filesystem is waiting for the issue_flush_fn to complete, you
could get a deadlock.
I wonder if it might be more appropriate to use GFP_NOIO as in the
following patch.
I wonder if it might be even more appropriate to cope better with a
kmalloc failure, especially as in this use, sd_sync_cache only will
use the sense information to print out a more informative error
message.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as544) adds a private entry point to scsi_remove_device, for
use when callers already own the scan_mutex. The appropriate callers are
modified to use the new entry point.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (as543) adds a private entry point to scsi_scan_target, for use
when the caller already owns the scan_mutex, and updates the kerneldoc for
that routine (which was badly out-of-date). It converts scsi_scan_channel
to use the new entry point. Lastly, it modifies scsi_get_host_dev to make
it acquire the scan_mutex, necessary since the routine adds a new
scsi_device even if it doesn't do any actual scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The problem is that klists claim to provide semantics for safe traversal of
lists which are being modified. The failure case is when traversal of a
list causes element removal (a fairly common case). The issue is that
although the list node is refcounted, if it is embedded in an object (which
is universally the case), then the object will be freed regardless of the
klist refcount leading to slab corruption because the klist iterator refers
to the prior element to get the next.
The solution is to make the klist take and release references to the
embedding object meaning that the embedding object won't be released until
the list relinquishes the reference to it.
(akpm: fast-track this because it's needed for the 2.6.13 scsi merge)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert commit 2b7d6a8cb9.
The "fix" was known to not even compile. Duh. That's not a fix.
That's just stupid.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CARD_... in hisax are all used with #if; CARD_FN_ENTERNOW_PCI lacks define
to 0 if corresponding config option is not set.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NDEBUG and NDEBUG_ABORT are almost always used as integers in NCR5380; added
define to 0 if they are not defined, switched lone ifdef NDEBUG into if.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All uses of ADDRLEN are comparisons with 64 (it's an address width).
added define to 32 (again, we only care about comparisons with 64)
if not defined.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the patch is whitespace cleanup, but more importantly, this patch
checks to see whether a callback is set before calling it. On cx88 boards
(currently the only boards using lgdt330x in 2.6.13) every callback is set.
However, newer drivers currently in development leave a callback undefined,
and lgdt330x must not call it if it isn't defined.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patrick Keene wrote to the linux-dvb list, asking where in menuconfig he
can enable dvb-bt8xx for his AVerMedia DVB card. I pointed the following
out to him:
config DVB_BT8XX
tristate "Nebula/Pinnacle PCTV/Twinhan PCI cards"
It has been agreed upon that this description is extremely misleading.
This patch changes the one-liner description text of dvb-bt8xx to something
more meaningful, and adds AVerMedia to the detailed description.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rewrite of the Indycam / VINO video v4l2 drivers for the SGI Indy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Mikael Nousiainen <tmnousia@cc.hut.fi>
Cc: <video4linux-list@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed a strange return value in smsc_ircc_init in
drivers/net/irda/smsc_ircc2.c in rc4-mm1.
When reaching the line "if (ircc_fir > 0 && ircc_sir > 0)", ret is 0. So I
don't see the point of setting it to 0 in the "else" case. >From what I
see in 2.6.12 it should probably be set to -ENODEV at the begining of the
"else" case. The attached patch does this.
Note that I didn't actually see any breakage caused by this.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRDA: smsc-ircc2 - do not over-use void * pointers, use specific
types wherever possible.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRDA: smsc-ircc2 - add sysfs support (platform device and driver) and
switch power management to the new scheme.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRDA: smsc-ircc2 - cleanup - do not pass around iobase, it can be
retrieved from smsc_ircc_cb structure.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The corgi keyboard has need of a switch event type with slightly type to the
input system as recommended by the input maintainer.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the platform specific Sharp SL-C7x0 LCD code from the
w100fb driver into a more appropriate place and updates the Corgi code to
match the new w100fb driver.
It also updates the corgi touchscreen code to match the new simplified
interface available from w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code w100fb was based on was horribly Sharp SL-C7x0 specific and there
was little else that could be done as I had no access to anything else with
a w100 in it. There is no real documentation about this chipset available.
Ian Molton has access to other platforms with the w100 (Toshiba e-series)
and so between us, we've improved w100fb and made it platform independent.
Ian Molton also added support for the very similar w3220 and w3200
chipsets.
There are a lot of changes here and it nearly amounts to a rewrite of the
driver but it has been extensively tested and is being used in preference
to the original driver in the Zaurus community. I'd therefore like to
update the mainline code to reflect this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corgi Touchscreen bugfix. If the PMU isn't running, the register needs to
be set to a sane value rather than reusing some random value.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up some Corgi Touchscreen logic and merge the repeat calls to
w100fb_blanking() in anticipation of the w100fb patch.
Fix a pm_message_t reference.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Corgi Touchscreen driver uses the PMU as an accurate timing source which
conflicts with its usage for performance monitoring. This patch allows it to
be shared with other users such as oprofile.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The input system handles key state tracking so there's no need for the driver
to do so as well. Also tidy up some comment formatting and remove a now
unneeded function.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some power management code to the corgi keyboard driver so that only one
power event gets reported within any reasonable time frame and the driver
doesn't enter an infinte loop due to key repeat.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a couple of compile errors in the corgi keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only show the scr file in sysfs for SD cards. Previously this was present
for all cards but had a contents of 0 for MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for Secure Digital specific features in the wbsd driver. Adds
support for read-only switch and wide bus transfers.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
