Pci error recovery support added.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev notifier are not unregistered if pci_register_driver fails.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable tx timeout recovery, if auto_fw_reset is disable
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off rx pause param and autoneg param is not supported so
return error in that case.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non privileged (VF) driver will not be able to carry out any of the FW update,
etc. operations. Disable the tools interface by not creating the sysfs nodes.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver checks TSO capability from FW before enabling it.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documented error code for attempts to set unsupported flags (or
to clear flags that cannot be disabled) is EINVAL, not EOPNOTSUPP.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes are made:
1.Obtain capabilities of Nic partition.
2.Configure tx bandwidth of particular Nic partition.
3.Configure the eswitch for setting port mirroring, enable mac
learning, promiscous mode.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver uses FW API version 2 and thus code corresponding to FW API
version 1 has become obsolete. Clean up this from the driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to free/alloc host resources during firmware
recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We first add mac address in driver local list and then send command to
fw to add same. There are checks in driver to ensure send command doesn't fail
before adding mac address in local list.
But instead fix should be:
Add mac address in fw and if it succeeds, add it in driver local list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of delaying rcv handshake till interface comes up,
do it just after fw load.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintian separate state for alloced and freed skb.
This can be done by null check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain set of register, base window addresses are not defined.
In such cases window should not set.
Return with error for such cases to avoid NMI.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between netif_stop_queue and netif_stopped_queue
check. So check once again if buffers are available to avoid race.
With above logic we can also get rid of tx lock in process_cmd_ring.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier all poll routine can process rx and tx, But now
one poll routine to process rx + tx and other for rx only.
Last msix vector will be used for separate tx interrupt.
o This is supported from fw version 4.4.2.
o Bump version 5.0.5
Signed-off-by: Sony Chacko <schacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove extra printing of mac address
o This driver also supports NIC only Qlogic adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device soft reset, don't halt every device block.
Access to some blocks is required during recovery.
Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the driver version number to 5.0.4
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code was placed incorrectly inside a block of code marked
with CONFIG_INET directive. Fix by moving it outside.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for NIC functions that work in non privileged mode where these
functions are privileged to do IO only, the control operations are handled via
privileged functions.
Bumped up version number to 5.0.3.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes have been added to enable the adapter to work in
NIC partitioning mode where multiple PCI functions of an adapter port can
be configured to work as NIC functions. The first function that is enumerated on
the PCI bus assumes the role of management function which, besides being able
to do all the NIC functionality, can configure other NIC partitions. Other NIC
functions can be configured as privileged or non privileged functions.
Privileged function can not configure other NIC functions but can do all the
NIC functionality including any firmware initialization, chip reset etc. Non
privileged functions can do only basic IO. For chip reset etc, it depends on the
privilege or management function.
1. Added code to determine PCI function number independent of kernel API.
2. Added Driver - FW version 2.0 support.
3. Changed producer and consumer register offset calculation.
4. Added management and privileged operation modes for npar functions. A module
parameter has been added to control it.
5. Added support for configuring the eswitch in the adapter.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device state need to be mark as FAILED, if fail to start firmware.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing register defines which are not used by Qlgoic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset/set DEV_UP bit during allocation and deallocation of resources.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default fw is loaded from flash, user can
change this priority using load_fw_file module param.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added lrobytes to it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Append mac address to adapter name.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes memory leak in error path when memory allocation
for adapter data structures fails.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ever driver changes the device state, it should write
pci-func number and timestamp in debug registers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device can go to quiescent state, during which drivers
should refrain from using the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci-func class can be other than ethernet in Qlogic CNA device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warn user if IDC version mismatch with different class of drivers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Window register is not per pci-func, so caching can
result in expected result.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before going for recovery, every pci-func should check fw state,
irrespective of device state. This to avoid unnecssary sending
of command for ctx destroy.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to indicate IDC(fw recovery) changes.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do netif_device_attach, even if resource allocation fails.
Driver callbacks can be called, if device is attached.
All these callbacks need to be protected by ADAPTER_UP_MAGIC check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rcv producer value should be read in spin-lock.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should not go ahead with fw recovery if fails to acquire
semaphore.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defining macro to set and clear driver state.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now any pci-func can start fw, whoever sees the reset ack first.
Before this, pci-func which sets the RESET state has the responsibility
to start fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different class of drivers co-exist for CNA device,
there is some minimal interaction that will be required amongst
the drivers for performing some device level operations.
All the driver should follow inter driver coexistence document.
Fixing polling interval and spelling mistake.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added additional driver statistics to track errors in rcv/tx path.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interface is down, mac address request are not sent to fw
but it is getting add in driver mac list.
Driver mac list should be in sync with fw i.e addresses communicated
to fw.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu_to_le32 was missing and used improperly.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface should be visible even if resource allocation fails.
netif_device_attach should be called for every netif_device_detach.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug print in driver, can be tuned by ethtool msg level
callback.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o USE/Read IDC defined timeout value from ROM.
o While resetting chip, don't wait for other pci-func to respond,
more than reset_ack_timeo seconds,
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect offset calculation and remove unnecessary remap
of the region in bar 0 to access onchip memory.
This was leading to read incorrect values by debug tools.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All QLogic converged NICs have 128-bit 128MB on card memory.
Fix the limit check from 64MB to 128MB and remove unnecessary
64-bit read/write checks.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rarely: Fw file size can be unaligned to 8.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Bios sub version from unified fw image is calculated incorrect.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate all sections of unified fw image, before accessing them,
to avoid seg fault.
Signed-off-by: Sucheta Chakraborty <sucheta@dut6195.unminc.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For promiscuous mode, driver send request to device for deleting
multicast addresses and again it send request for adding them back
while exiting from this mode, this is bad for performance.
Just setting device in promiscuous mode is enough, no need to del/add
multicast addresses.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics added for lro/lso bytes, count for tx stop queue and
wake queue and skb alloc failure count.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removed some needless checks and also corrected bug in lp486e (dmi was passed
instead of dmi->dmi_addr)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resoruce cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump and FW health registers should be dump
in any case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o After firmware recovery, clear device reset state transition register.
Otherwise firmware reload can occur unnecessary.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing identifier that distinguishes between
FCOE/ISCSI/ETHERNET functions.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into
correct section in every case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
