Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1X8QAKCRDj7w1vZxhR
xX9ZAP9KwFKKehrS1QJjTHKeowUKEnRHuDj2MlwTZJgCw/AMMgEAzgRZwY/VH/Os
aQIhJho9hWmBE0dePIZuWzzCp1giNw8=
=7jQV
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner H3 and H5 changes for 5.1
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
* tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: libretech-all-h3-cc: Mark eMMC HS-DDR 3.3V capable
ARM: dts: sunxi: h3/h5: Drop A31 fallback compatible for CSI controller
ARM: dts: sun8i-h3: nanopi-m1-plus: enable HDMI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add SMMU node for Stratix10
- Add vendor prefix fo Novtech
- Add a new 96Boards Chameleon96 board that uses a Cyclone5 SoCFPGA
- Add missing reset properties for all IP on Cyclone5 and Arria10
-----BEGIN PGP SIGNATURE-----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=8OgV
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.1
- Add SMMU node for Stratix10
- Add vendor prefix fo Novtech
- Add a new 96Boards Chameleon96 board that uses a Cyclone5 SoCFPGA
- Add missing reset properties for all IP on Cyclone5 and Arria10
* tag 'socfpga_dts_for_v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: update more missing reset properties
ARM: dts: socfpga: update missing reset property peripherals
ARM: dts: Add support for 96Boards Chameleon96 board
dt-bindings: vendor-prefixes: Add Novtech Vendor Prefix
arm64: dts: stratix10: Add Stratix10 SMMU support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Fixup GIC IRQ flags and GSBI state on MSM8660
* Add USB OTG, gpio ranges, and Wifi support on MSM8974 Hammerhead
* Remove skeleton.dtsi on IPQ4019
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0M2a
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/dt
Qualcomm Device Tree Changes for v5.1
* Fixup GIC IRQ flags and GSBI state on MSM8660
* Add USB OTG, gpio ranges, and Wifi support on MSM8974 Hammerhead
* Remove skeleton.dtsi on IPQ4019
* tag 'qcom-dts-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: ipq4019: Remove skeleton.dtsi
ARM: dts: qcom: msm8974-hammerhead: add USB OTG support
ARM: dts: qcom: msm8974: add gpio-ranges
ARM: dts: qcom: msm8974-hammerhead: add WiFi support
ARM: dts: msm8660: Fix up GIC IRQ flags
ARM: dts: msm8660: Mark two GSBI blocks "disabled"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are the changes for ARM NXP LPC32xx and ARM NXP LPC18xx/LPC43xx
devicetree files:
* added dts file for MYIR Tech MYD-LPC4357 development board,
* two missing properties are added to LPC32xx keypad controller device
tree node, this fixes a long-standing problem with its initialization,
* LPC32xx PL11x LCD controller device node got corrected properties,
which allows to use it with a new PL11x DRM driver,
* output voltage level on one of Phytec phyCORE-LPC3250 fixed regulators
is corrected, the fix is needed to remove duplicating platform data,
* Phytec phyCORE-LPC3250 board gets a description of a kit LCD panel,
this completes setup of CLCD device tree node for the board,
* added unit addresses to memory device nodes on EA and Phytec boards,
* fixes of ordinary warnings in dts formatting like leading zeroes,
unused address and size cell properties and so on.
-----BEGIN PGP SIGNATURE-----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=J1uJ
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-dt-for-5.1' of https://github.com/vzapolskiy/linux-lpc32xx into arm/dt
ARM: lpc32xx: devicetree updates for v5.1
Here are the changes for ARM NXP LPC32xx and ARM NXP LPC18xx/LPC43xx
devicetree files:
* added dts file for MYIR Tech MYD-LPC4357 development board,
* two missing properties are added to LPC32xx keypad controller device
tree node, this fixes a long-standing problem with its initialization,
* LPC32xx PL11x LCD controller device node got corrected properties,
which allows to use it with a new PL11x DRM driver,
* output voltage level on one of Phytec phyCORE-LPC3250 fixed regulators
is corrected, the fix is needed to remove duplicating platform data,
* Phytec phyCORE-LPC3250 board gets a description of a kit LCD panel,
this completes setup of CLCD device tree node for the board,
* added unit addresses to memory device nodes on EA and Phytec boards,
* fixes of ordinary warnings in dts formatting like leading zeroes,
unused address and size cell properties and so on.
* tag 'lpc32xx-dt-for-5.1' of https://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: ea3250: beautify gpio keys children nodes
ARM: dts: lpc32xx: ea3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: setup LCD controller to panel interface
ARM: dts: lpc32xx: phy3250: remove regulators umbrella device node
ARM: dts: lpc32xx: phy3250: fix SD card regulator voltage
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller clocks property
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller variant
ARM: dts: lpc32xx: reparent keypad controller to SIC1
ARM: dts: lpc32xx: add required clocks property to keypad device node
ARM: dts: Add DT for MYIR Tech MYD-LPC4357 Development Board
ARM: dts: lpc32xx: Remove leading 0x and 0s from bindings notation
ARM: dts: lpc435x: remove address and size cells from gpio-keys-polled nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.1, please pull the following:
- Dan relicenses the Luxul DTS files to GPL 2.0+/MIT
- Hao adds support for the Phicomm K3 which is a BCM4709 SoC with dual
BCM4366 radio
- Stefan adds support for the Raspberry Pi A+: binding and DTS files. He
also provides a bunch of DTC warning fixes for the different RPi DTS(i)
files and adds support for missing GPIO lines on RPi 2/3
-----BEGIN PGP SIGNATURE-----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=Ykbm
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.1, please pull the following:
- Dan relicenses the Luxul DTS files to GPL 2.0+/MIT
- Hao adds support for the Phicomm K3 which is a BCM4709 SoC with dual
BCM4366 radio
- Stefan adds support for the Raspberry Pi A+: binding and DTS files. He
also provides a bunch of DTC warning fixes for the different RPi DTS(i)
files and adds support for missing GPIO lines on RPi 2/3
* tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
ARM: dts: bcm283x: Add missing GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED
ARM: dts: bcm2837-rpi-3-b: Use consistent label for HDMI hotplug
ARM: dts: bcm2835: Fix labels for GPIO 0,1
ARM: dts: bcm2835-rpi: Drop unnecessary #address-cells/#size-cells
ARM: dts: bcm283x: Fix DTC warning for memory node
ARM: dts: add Raspberry Pi 3 A+
dt-bindings: bcm: Add Raspberry Pi 3 A+
ARM: dts: BCM5301X: Add basic DT for Phicomm K3
ARM: dts: BCM53573: Relicense Luxul files to the GPL 2.0+ / MIT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Extend support for Aries family of mobile devices (e.g. Samsung
Galaxy S) based on S5Pv210 SoC: DRM Rotator, FIMD, PWM vibrator,
power off, touchscreen, Broadcom BCM4329 Bluetooth and cpufreq.
2. Remove hardcoded bootargs on Galaxy S family (proper support in
U-Boot).
3. Fix minor DTC warnings.
4. Fix Exynos4412 Odroid X2/U3 conflicting eMMC GPIO settings and regulator
properties.
5. Fix the eMMC RTSN pin breaking proper reboot on X2.
-----BEGIN PGP SIGNATURE-----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=9+iJ
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.1
1. Extend support for Aries family of mobile devices (e.g. Samsung
Galaxy S) based on S5Pv210 SoC: DRM Rotator, FIMD, PWM vibrator,
power off, touchscreen, Broadcom BCM4329 Bluetooth and cpufreq.
2. Remove hardcoded bootargs on Galaxy S family (proper support in
U-Boot).
3. Fix minor DTC warnings.
4. Fix Exynos4412 Odroid X2/U3 conflicting eMMC GPIO settings and regulator
properties.
5. Fix the eMMC RTSN pin breaking proper reboot on X2.
* tag 'samsung-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix pinctrl definition for eMMC RTSN line on Odroid X2/U3
ARM: dts: exynos: Fix eMMC regulator properties on Odroid U3 boards
ARM: dts: exynos: Fix conflicting fixed-regulator GPIO flags and properties
ARM: dts: s3c2416: Fix xti node's missing reg property warning
ARM: dts: s5pv210: Fix onenand's unit address format warning
ARM: dts: s5pv210: Add DMC nodes
ARM: dts: s5pv210: Add support for more devices present on Aries
ARM: dts: s5pv210: Add reserved memory for MFC on Aries
ARM: dts: s5pv210: Remove hardcoded bootargs on Galaxy S and Fascinate 4G
ARM: dts: s5pv210: Use correct fimd variant
ARM: dts: s5pv210: Add node for exynos-rotator
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
improvements for rv1108 as well. RK3066 got support for the core
display components and the Edison tablet got its touchscreen added.
Apart from that a wider fix to drop display-wp usage from places where
it shouldn't be used, a pin fix for Edison and a cleanup to prevent
rk3036 board from defining sound-dai-cells for core components in
each board separately.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlxTAPIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYbQCACiWIYVLrOwOPSgDo3xRFygo2Bmlo2EncEz
UZM0z3gQpzQ8go7Ms6eqL7qRoMI14Cc3XT6dNkzjRBIBaJAi3LXy1G4CLMzxuurD
qri6shmJv94TfBNISJ9FOQYqJRxSK1z4ncp6iXNeOgOa9NCkqSXkHTOve8oVAxfj
nBnMAA0kkX/haF4pNaLoDUv3ppMi7UHjAuoyJMNaTFqVG9qjR1DPNBnCGdYZGacU
Xkb/9n/QOLsJc/yoMcUno+Q5tUVkLsxQVhsApf9Tf7Hd76WV0dgIzi0hENvoKJjK
TwfHz26NyNzw9KbX5YJmNGUAbgesjVBx5AXJk+pBZvrBWGUDtixE
=VDwG
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New board the Elgin-R1 based on the rv1108 soc and a number of small
improvements for rv1108 as well. RK3066 got support for the core
display components and the Edison tablet got its touchscreen added.
Apart from that a wider fix to drop display-wp usage from places where
it shouldn't be used, a pin fix for Edison and a cleanup to prevent
rk3036 board from defining sound-dai-cells for core components in
each board separately.
* tag 'v5.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: clean up the abuse of disable-wp
ARM: dts: rv1108: Add support for rv1108-elgin-r1 board
dt-bindings: Add vendor prefix for elgin
ARM: dts: rockchip: rv1108: Add spim0 and spim1 pinctrl groups
ARM: dts: rockchip: Add missing dma-names SPI support for rv1108
ARM: dts: rockchip: add rk3066 vop display nodes
ARM: dts: rockchip: add focaltech touchscreen to rk3188-bqedison2qc
ARM: dts: rockchip: fix cif1_pdn pin on rk3188-bqedison2qc
ARM: dts: rockchip: add HCLK_HDMI to rk3066 vio power-domain
ARM: dts: rockchip: move rk3036 i2s sound-dail-cells into soc dtsi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mic input on da850 LCDK board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6oqi
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.1/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/dt
DaVinci device-tree updates for v5.1 contains a patch to enable analog
mic input on da850 LCDK board.
* tag 'davinci-for-v5.1/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Enable the analog mic input
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series contains board specific dts updates and few minor
clean-up changes:
- add stdout-path for am335x-chiliboard
- add wlcore wakeirq for omap3-evm, pandaboard and omap4-droid4
- remove unnecessary address-cells and io-cells for am33xx
- replace deprecated linux,wakeup with wakeup-source property
- use spdx license for am335x-shc
- configure ethernet pins for omap4-sdp
-----BEGIN PGP SIGNATURE-----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=6JIq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.1/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
dts updates for omap variants for v5.1 merge window
This series contains board specific dts updates and few minor
clean-up changes:
- add stdout-path for am335x-chiliboard
- add wlcore wakeirq for omap3-evm, pandaboard and omap4-droid4
- remove unnecessary address-cells and io-cells for am33xx
- replace deprecated linux,wakeup with wakeup-source property
- use spdx license for am335x-shc
- configure ethernet pins for omap4-sdp
* tag 'omap-for-v5.1/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-sdp: Make ethernet working even if booted with latest u-boot
ARM: dts: am335x-shc.dts: Switch to SPDX identifier
ARM: dts: am437x: replace linux,wakeup with wakeup-source property
ARM: dts: am33xx: Remove unnecessary properties
ARM: dts: omap4-droid4: Configure wlcore wakeirq
ARM: dts: Configure wlcore wakeirq for pandaboard
ARM: dts: Add wlcore wakeirq for omap3-evm
ARM: dts: am335x-chiliboard: Add stdout-path property
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two changes to add support for McGill University's IceBoard telescope
ARM + FPGA instrumentation board. This board is used for several
telescopes around the world, see the related device tree commit for
some interesting links for more information.
Note that these changes are based on the related ti81xx soc changes.
-----BEGIN PGP SIGNATURE-----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=ucZD
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.1/dt-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
dts updates for ti81xx for v5.1 merge window
Two changes to add support for McGill University's IceBoard telescope
ARM + FPGA instrumentation board. This board is used for several
telescopes around the world, see the related device tree commit for
some interesting links for more information.
Note that these changes are based on the related ti81xx soc changes.
* tag 'omap-for-v5.1/dt-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874
ARM: dts: ti81xx: Add dts boilerplate for all GPIO and SPI peripherals
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlxS/KYQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgUdCB/9d8IN+iZUxo1TX5QS0ov+1FYhkly6FNEj2
JGQYL5zCDGe5RvgfyqL3vi3kHFQoDIHjsRQBUl14/ryo+InIl8ZJWl38tFjHYmdw
o883g3zyJLbwKrsE2RBtWtWsoK5TSwbV7xR3JO8tHWFV+mXDUUcFFXpR5VRjnQ9l
XsjvvzznfQQLpUzJy5OAjTAhtvkXExM74h4MpwIXtyeqrWUI73a6uBUeY6Js43rZ
zTfyv8Ikla3eP+fMQqf60CwKjxhQwyG7/7UxWp7iIatsUMeC5VLRCZuM7l109pH0
hKQLWybzcReCPfTqQ2rAwAhBQmQIpEvdwhFk5WA1mmqMi/d/Zdoh
=oEEi
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Drop one non-existent component from powerdomain list.
* tag 'v5.0-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove qos_cif1 from rk3188 power-domain
This series contains two SoC regression fixes and one uninitialized
variable fix:
- Fix inverted nirq pin handling for omap5 that started producing
warnings with earlier GIC direction checks and took a while to
understand and confirm. Basically there are two sys_nirq pins
that are bypassing peripheral modules and inverted automatically
by the SoC and need to be handled with a custom irq_set_type()
- Recent ti-sysc changes caused a regression to the pwm-omap-dmtimer
code where the device tree handling code for timer source clock
gets confused. It looks like we can remove that code eventually,
but for now we just drop a bogus pm_runtime_irq_safe() for the
timers with the related quirks caused by pm_runtime_irq_safe(),
and have the standard assigned-clocks and assigned-clock-parents
deal with setting the source clock
- Fix potentially uninitialized value for display init code if
regmap_read() fails
-----BEGIN PGP SIGNATURE-----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=5oVS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.0/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
SoC fixes for omaps for v5.0-rc cycle
This series contains two SoC regression fixes and one uninitialized
variable fix:
- Fix inverted nirq pin handling for omap5 that started producing
warnings with earlier GIC direction checks and took a while to
understand and confirm. Basically there are two sys_nirq pins
that are bypassing peripheral modules and inverted automatically
by the SoC and need to be handled with a custom irq_set_type()
- Recent ti-sysc changes caused a regression to the pwm-omap-dmtimer
code where the device tree handling code for timer source clock
gets confused. It looks like we can remove that code eventually,
but for now we just drop a bogus pm_runtime_irq_safe() for the
timers with the related quirks caused by pm_runtime_irq_safe(),
and have the standard assigned-clocks and assigned-clock-parents
deal with setting the source clock
- Fix potentially uninitialized value for display init code if
regmap_read() fails
* tag 'omap-for-v5.0/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be uninitialized
ARM: dts: Configure clock parent for pwm vibra
bus: ti-sysc: Fix timer handling with drop pm_runtime_irq_safe()
ARM: OMAP5+: Fix inverted nirq pin interrupts with irq_set_type
clocksource: timer-ti-dm: Fix pwm dmtimer usage of fck reparenting
Before we fixed up the interrupt hierarchy for the SSBI
GPIO controller, we had to use the PM8058 directly to pick
interrupts. After making the interrupt controller work properly,
we can reference the real interrupt parent.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
Note that the IRQs started at 24 instead of 192 like all of the other
PMICs. This is the same IRQs as the MPP for this board. qcom-pm8xxx.c
doesn't set the shared IRQs so this is highly likely to be a copy and
paste error.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on an APQ8060 DragonBoard with no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The lcd display of the gta04 has a backlight but the backlight
was not referenced in the lcd node, so screen blanking did
not turn off the backlight. Fix that.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Bosch Guardian is a TI am335x based device.
It's hardware specifications are as follows:
* 256 MB DDR3 memory
* 512 MB NAND Flash
* USB OTG
* RS232
* MicroSD external storage
* LCD Display interface
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
[tony@atomide.com: updated to use #include]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the commit 700a38b27e ("Input: gpio_keys -
switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The EVM consists of a system on module (SOM) and baseboard, and LCD.
This patch adds a DTSI file for the SOM and baseboard separately,
then a wrapper to combine them and specify processor type and a
LCD information.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that all sensors supplied by reg_sensors have supported
regulator control, reg_sensors does NOT need to be always ON,
remove "regulator-always-on" to save power.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mma8451 sensor driver has supported regulators control,
assign the power supplies for mma8451 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mag3110 sensor driver has supported regulators control,
assign the power supplies for mag3110 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The isl29023 light sensor driver has supported regulator control,
assign the power supply for isl29023 to enable the control.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Zodiac Digital Tapping Unit, a VF610 based network device with
5 Ethernet ports. One of these ports supports 1000Base-T2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pfla02 SoM has a Micrel KSZ9031RNX ethernet phy connected to the FEC,
which needs RX and TX clock skew settings to compensate for differences
in line length. The skew values are taken from barebox commit
4c65c20f1071 ("ARM: pfla02: Set new ethernet phy tx timings"), which
is based on patches originally provided by Phytec:
TX_CLK line is approx. 54mm longer than other TX lines which adds
a delay of 0.36ns. RGMII need a delay of min. 1.0ns. This mean we
have to add a delay of 0.64ns. We choose 0.78 to have a little gap.
This can be done by setting GTX pad skew value to 11100
Also add a delay for the RX delay lines, needed for the Duallite
variant. => Set register 2.8 (RGMII Clock Pad Skew) to 0x039F.
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DA9063 device need the required "interrupt-controller" property as
documented by the bindings [1].
[1] Documentation/devicetree/bindings/mfd/da9063.txt
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the GPIO line names from the schematics to get them displayed
in the debugfs output of each GPIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
USB_VBUS is a controlled by a Silergy SY6288CCAC-GP 2A Power
Distribution Switch. The name of it's enable GPIO signal is USB_PWR_EN.
VCC5V is supplied by the main power input called PWR_5V_STB. The name of
it's enable GPIO signal is 3V3_5V_EN.
VCC3V3, VCC_DDR3_1V5 and VCCK (the CPU power supply) each use a separate
Silergy SY8089AAC-GP 2A step down regulator. They are all supplied by the
board's main 5V. VCC3V3 and VCC_DDR3_1V5 are fixed regulators while the
voltage of VCCK can be changed by changing it's feedback voltage via
PWM_C.
VCC1V8 is an ABLIC S-1339D18-M5001-GP fixed voltage regulator which is
supplied by VCC3V3.
VCC_RTC is a Global Mixed-mode Technology Inc. G918T12U-GP LDO which. It
is supplied by either VCC3V3 (when the board is powered) or the RTC coin
cell battery.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The INTR32 pin of the IP101GR Ethernet PHY is routed to the GPIOH_3 pad
on the SoC.
Enable the interrupt function of the PHY's INTR32 pin to switch it from
it's default "receive error" mode to "interrupt pin" mode.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SAR ADC enabled channel 8 can be used to measure the chip temperature.
This can be made available to the hwmon subsystem by using iio-hwmon.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SAR ADC can measure the chip temperature of the SoC. This only
works if the chip is calibrated and if the calibration data is written
to the correct registers. The calibration data is stored in the upper
two bytes of eFuse offset 0x1f4.
This adds the eFuse cell for the temperature calibration data and
passes it to the SAR ADC. We also need to pass the HHI sysctrl node to
the SAR ADC because the 4th TSC (temperature sensor calibration
coefficient) bit is stored in the HHI region (unlike bits [3:0] which
are stored directly inside the SAR ADC's register area).
On boards that have the SAR ADC enabled channel 8 can be used to
measure the chip temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SAR ADC can measure the chip temperature of the SoC. This only
works if the chip is calibrated and if the calibration data is written
to the correct registers. The calibration data is stored in the upper
two bytes of eFuse offset 0x1f4.
This adds the eFuse cell for the temperature calibration data and
passes it to the SAR ADC. We also need to pass the HHI sysctrl node to
the SAR ADC because the 4th TSC (temperature sensor calibration
coefficient) bit is stored in the HHI region (unlike bits [3:0] which
are stored directly inside the SAR ADC's register area).
On boards that have the SAR ADC enabled channel 8 can be used to
measure the chip temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SAR ADC on Meson8m2 is slightly different compared to Meson8. The
ADC functionality is identical but the calibration of the internal
thermal sensor is different.
Use the Meson8m2 specific compatible so the temperature sensor is
calibrated correctly on boards using the Meson8m2 SoC.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller on Meson8/Meson8m2 and Meson8b is part of a
register region called "HHI". This register area contains more
functionality than just a clock controller:
- the clock controller
- some reset controller bits
- temperature sensor calibration data (on Meson8b and Meson8m2 only)
- HDMI controller
Allow access to this HHI register area as "system controller". Also
migrate the Meson8 and Meson8b clock controllers to this new node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the stmpe-adc DT node as found on Toradex iMX6 modules
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A valid WEIM range configuration must specify range entries for
all four chip selects. This fixes an error on boot:
imx-weim: probe of 21b8000.weim failed with error -22
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an
i.MX6UL or i.MX6ULL SOM and various add-on boards.
The following adds support for the "Full Featured" version of the Segin,
which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation
module.
Its hardware specifications are:
* 512MB DDR3 memory
* 512MB NAND flash
* Dual 10/100 Ethernet
* USB Host and USB OTG
* RS232
* MicroSD external storage
* Audio, RS232, I2C, SPI, CAN headers
* Further I/O options via A/V and Expansion headers
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit d2d0ad2aec ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL has errata ERR010450, there is I/O timing limitation,
for SDR mode, SD card clock can't exceed 150MHz, for DDR mode,
SD card clock can't exceed 45MHz. This patch change to use the
new compatible "fsl,imx6ull-usdhc" to follow this limitation.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since imx6ulz.dtsi includes imx6ull.dtsi, we only need to fix the compatible
string here to achieve the correct OTP size for both SoCs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was implemented in the driver but not actually defined and
referenced in dts. This makes it always on.
From reference manual in section "10.4.1.4.1 Power Distribution":
"Display domain - The DISPLAY domain contains GIS, CSI, PXP, LCDIF,
PCIe, DCIC, and LDB. It is supplied by internal regulator."
The current pd_pcie is actually only for PCIE_PHY, the PCIE ip block is
actually inside the DISPLAY domain. Handle this by adding the pcie node
in both power domains.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These have been disable since the change to probe Marvell Ethernet
switches as MDIO devices. Remove the properties now that the code to
suppport them will also be removed soon.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add du node to r8a7744 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the comphy settings for the Ethernet interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DT description for the Armada 38x common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GTA04 has a w2sg0004 or w2sg0084 gps chip. Not detectable
which one is mounted so use the compatibility entry for w2sg0004
for all which will work for both.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Required for completeness sake to be able to specify
a regulator for devices having a non-optional regulator
property. It corresponds to the "3V3" net in the
schematics.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is one button and a notifier for incoming phone
calls/text messages for which we should wakeup from
suspend.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to use an external link when the file is already here.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc81 ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.
The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.
A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.
Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regarding the 'gpio_keys' device node a dtc reports a couple of
warnings:
Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Warning (unit_address_vs_reg): /gpio_keys/button@21: node has
a unit name, but no reg property
The change fixes these issues and adds empty lines between adjacent
children device nodes. The device node itself is renamed by substituting
an underscore by hyphen to follow the standard naming convention
of device tree nodes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds description of Sharp LQ035Q7DB03 3.5" 320x240 TFT panel,
which is connected to Phytec phyCORE-LPC3250 board, ARM PrimeCell PL111
LCD controller on NXP LPC3250 SoC gets its configuration appropriately
to support graphics output to the panel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
Fixes: d06670e962 ("arm: dts: phy3250: add SD fixed regulator")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added ARM PrimeCell PL111 clocks property misses
the required "clcdclk" clock, which is the same as a clock to enable
the LCD controller on NXP LPC3230 and NXP LPC3250 SoCs.
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM PrimeCell PL111 LCD controller is found on On NXP LPC3230
and LPC3250 SoCs variants, the original reference in compatible
property to an older one ARM PrimeCell PL110 is invalid.
Fixes: e04920d9ef ("ARM: LPC32xx: DTS files for device tree conversion")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching to a new interrupt controller scheme by separating SIC1
and SIC2 from MIC interrupt controller just one SoC keypad controller
was not taken into account, fix it now:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:524 irq_domain_associate+0x50/0x1b0
error: hwirq 0x36 is too large for interrupt-controller@40008000
...
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Fixes: 9b8ad3fb81 ("ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx keypad controller requires a clock property to be defined.
The change fixes the driver initialization problem:
lpc32xx_keys 40050000.key: failed to get clock
lpc32xx_keys: probe of 40050000.key failed with error -2
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Add support for MYIR Tech MYD-LPC4357 Development Board and
MY-LCD70TP-C 7" TFT LCD module with Innolux AT070TN82 panel.
The board contains quite rich periferals, the list features
NXP LPC4357 SoC, 32 MB SDRAM, 4 MB SPI Flash, audio input/output
interface, LCD panel, micro SD card slot, USB, USB OTG, Ethernet,
2 CAN ports, 4 UARTs, I2C and SPI interfaces routed to external
interface.
More information can be found on http://www.myirtech.com/list.asp?id=422
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rv1108-elgin-r1 board the RK805 VCC5 and VCC6 supplies come from
the BUCK2 regulator at 2.2V, so fix the representation in the
device tree.
While at it, rename it from vdd_cam to vdd_buck2, which is a better
name for the regulator label.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
the missing GPIO labels for RPi 2/3. Additionally it contains
some minor DT fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=kLKJ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=a1d7
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2019-02-01' into devicetree/next
This pull request adds support for the new Raspberry Pi 3 A+ and
the missing GPIO labels for RPi 2/3. Additionally it contains
some minor DT fixes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is no need to specify a pinctrl for the reset GPIO. So we better
remove this avoid a potential conflict between pinctrl and pwrseq
after the pinmux driver has been changed to strict:
pinctrl-bcm2835 20200000.gpio: pin gpio41 already requested by wifi-pwrseq;
cannot claim for pinctrl-bcm2835:499
pinctrl-bcm2835 20200000.gpio: pin-41 (pinctrl-bcm2835:499) status -22
pwrseq_simple: probe of wifi-pwrseq failed with error -22
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The GPIO sysfs is deprecated and disabled in the defconfig files.
So in order to motivate the usage of the new GPIO character device API
add the missing GPIO line names for Raspberry Pi 2 and 3. In the lack
of full schematics i would leave all undocumented pins as unnamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The RPI 3 B+ provides control to both LEDs (PWR and ACT). So append
the first letter of the LED color (like in the schematics) in order
to clarify this.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
This make the GPIO label for HDMI hotplug more consistent to the other
boards.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the schematics for all RPis with a 40 pin header,
the GPIOs 0 and 1 are labeled as ID_SD and ID_SC. In order to
clarify that is a I2C bus, append the third letter.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm2835-rpi.dtsi with W=1 leads to the following warning:
Warning (avoid_unnecessary_addr_size): /soc/firmware: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Fix this by removing these unnecessary properties.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm283x DTS with W=1 leads to the following warning:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property,
but no unit name
Fix this by adding the unit address.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Compared to the Raspberry Pi 3 B it isn't possible to control BT_ON and
WL_ON separately.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
This patch adds all SPI instances of the STM32F429 SoC.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The GRAFX domain only contains V3D, and this driver should be the only
accessor of V3D (firmware usage gets disabled when V3D is in the DT),
so we can safely make Linux control the GRAFX and GRAFX_V3D power
domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
It was covering part of the PM block's range, up to the WDT regs. To
support the rest of the PM block's functionality, we need the full
register range plus the AXI Async Bridge regs for PM sequencing.
This doesn't convert any of the consumers over to the new binding yet,
since we will need to be careful in coordinating our usage of firmware
services that might power domains on and off versus the bcm2835-pm
driver's access of those same domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
a PIC microcontroller, which is in turn wired to UART1 of main board.
Signed-off-by: Hao Dong <halbertdong@gmail.com>
[rmilecki: drop chosen { }, fix whitespaces, update commit message]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
