Checking the bearer min mtu with tipc_udp_mtu_bad() only works for
IPv4 UDP bearer, and IPv6 UDP bearer has a different value for the
min mtu. This patch checks with encap_hlen + TIPC_MIN_BEARER_MTU
for min mtu, which works for both IPv4 and IPv6 UDP bearer.
Note that tipc_udp_mtu_bad() is still used to check media min mtu
in __tipc_nl_media_set(), as m->mtu currently is only used by the
IPv4 UDP bearer as its default mtu value.
Fixes: 682cd3cf94 ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing link mtu negotiation, a malicious peer may send Activate msg
with a very small mtu, e.g. 4 in Shuang's testing, without checking for
the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then
n->links[bearer_id].mtu is set to 4294967228, which is a overflow of
'4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss().
With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning:
tipc: Too large msg, purging xmit list 1 5 0 40 4!
tipc: Too large msg, purging xmit list 1 15 0 60 4!
And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in
named_distribute(), and when purging it in tipc_link_xmit(), a crash
was even caused:
general protection fault, probably for non-canonical address 0x2100001011000dd: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.3.0.neta #19
RIP: 0010:kfree_skb_list_reason+0x7e/0x1f0
Call Trace:
<IRQ>
skb_release_data+0xf9/0x1d0
kfree_skb_reason+0x40/0x100
tipc_link_xmit+0x57a/0x740 [tipc]
tipc_node_xmit+0x16c/0x5c0 [tipc]
tipc_named_node_up+0x27f/0x2c0 [tipc]
tipc_node_write_unlock+0x149/0x170 [tipc]
tipc_rcv+0x608/0x740 [tipc]
tipc_udp_recv+0xdc/0x1f0 [tipc]
udp_queue_rcv_one_skb+0x33e/0x620
udp_unicast_rcv_skb.isra.72+0x75/0x90
__udp4_lib_rcv+0x56d/0xc20
ip_protocol_deliver_rcu+0x100/0x2d0
This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(),
and not updating mtu if it is too small.
Fixes: ed193ece26 ("tipc: simplify link mtu negotiation")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As different media may requires different min mtu, and even the
same media with different net family requires different min mtu,
add tipc_bearer_min_mtu() to calculate min mtu accordingly.
This API will be used to check the new mtu when doing the link
mtu negotiation in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87e3bee0f2 ("net: mdio: i2c: Separate C22 and C45 transactions")
separated the non-rollball bus accessors, but left the rollball
accessors as is. As rollball accessors are clause 45, this results
in the rollball protocol being completely non-functional. Fix this.
Fixes: 87e3bee0f2 ("net: mdio: i2c: Separate C22 and C45 transactions")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.
Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.
Fixes: 26312c685a ("net: fec: correct the counting of XDP sent frames")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff.
Fixes: c411ed8545 ("nsh: add GSO support")
Reported-by: syzbot+632b5d9964208bfef8c0@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Lan says:
====================
net: hns3: fix some bug for hns3
There are some bugfixes for the HNS3 ethernet driver. patch#1 fix miss
checking for rx packet. patch#2 fixes VF promisc mode not update
when mac table full bug, and patch#3 fixes a nterrupts not
initialization in VF FLR bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8c ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.
So fix it by increasing the tx queue print buffer length.
Fixes: 630a6738da ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexis Lothoré says:
====================
net: dsa: rzn1-a5psw: fix STP states handling
This small series fixes STP support and while adding a new function to
enable/disable learning, use that to disable learning on standalone ports
at switch setup as reported by Vladimir Oltean.
This series was initially submitted on net-next by Clement Leger, but some
career evolutions has made him hand me over those topics.
Also, this new revision is submitted on net instead of net-next for V1
based on Vladimir Oltean's suggestion
Changes since v2:
- fix commit split by moving A5PSW_MGMT_CFG_ENABLE in relevant commit
- fix reverse christmas tree ordering in a5psw_port_stp_state_set
Changes since v1:
- fix typos in commit messages and doc
- re-split STP states handling commit
- add Fixes: tag and new Signed-off-by
- submit series as fix on net instead of net-next
- split learning and blocking setting functions
- remove unused define A5PSW_PORT_ENA_TX_SHIFT
- add boolean for tx/rx enabled for clarity
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 20704bd163 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: 20704bd163 ("erspan: build the header with the right proto according to erspan_ver")
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Kevin Traynor <ktraynor@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp_v4_send_reset() is called with @sk == NULL,
we do not change ctl_sk->sk_priority, which could have been
set from a prior invocation.
Change tcp_v4_send_reset() to set sk_priority and sk_mark
fields before calling ip_send_unicast_reply().
This means tcp_v4_send_reset() and tcp_v4_send_ack()
no longer have to clear ctl_sk->sk_mark after
their call to ip_send_unicast_reply().
Fixes: f6c0f5d209 ("tcp: honor SO_PRIORITY in TIME_WAIT state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default we would not want RXFCS and RXALL features enabled as they are
mainly intended for debugging purposes. This does not stop users from
enabling them later on as needed.
Fixes: 8e57daf706 ("sfc_ef100: RX path for EF100")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As not all ICE_TX_FLAGS_* fit in current 16-bit limited
tx_flags field that was introduced in the Fixes commit,
VLAN-related information would be discarded completely.
As such, creating a vlan and trying to run ping through
would result in no traffic passing.
Fix that by refactoring tx_flags variable into flags only and
a separate variable that holds VLAN ID. As there is some space left,
type variable can fit between those two. Pahole reports no size
change to ice_tx_buf struct.
Fixes: aa1d3faf71 ("ice: Robustify cleaning/completing XDP Tx buffers")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that we mostly get netdev CCed on wireless patches
which are written by people who don't know any better and
CC everything that get_maintainers spits out. Rather than
patches which indeed could benefit from general networking
review.
Marking them down in patchwork as Awaiting Upstream is
a bit tedious.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch corrects the NFP_NET_MAX_DSCP definition in the main.h file.
The incorrect definition result DSCP bits not being mapped properly when
DCB is set. When NFP_NET_MAX_DSCP was defined as 4, the next 60 DSCP
bits failed to be set.
Fixes: 9b7fe8046d ("nfp: add DCB IEEE support")
Cc: stable@vger.kernel.org
Signed-off-by: Huayu Chen <huayu.chen@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/netlink/ contains machine-readable protocol
specs in YAML. Those are much like device tree bindings,
no point CCing docs@ for the changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Neil moved away from SCTP related duties.
Move him to CREDITS then and while at it, update SCTP
project website.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 565b4824c3 ("devlink: change port event netdev notifier
from per-net to global") changed original per-net notifier to be
per-devlink instance. That fixed the issue of non-receiving events
of netdev uninit if that moved to a different namespace.
That worked fine in -net tree.
However, later on when commit ee75f1fc44 ("net/mlx5e: Create
separate devlink instance for ethernet auxiliary device") and
commit 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in
case of PCI device suspend") were merged, a deadlock was introduced
when removing a namespace with devlink instance with another nested
instance.
Here there is the bad flow example resulting in deadlock with mlx5:
net_cleanup_work -> cleanup_net (takes down_read(&pernet_ops_rwsem) ->
devlink_pernet_pre_exit() -> devlink_reload() ->
mlx5_devlink_reload_down() -> mlx5_unload_one_devl_locked() ->
mlx5_detach_device() -> del_adev() -> mlx5e_remove() ->
mlx5e_destroy_devlink() -> devlink_free() ->
unregister_netdevice_notifier() (takes down_write(&pernet_ops_rwsem)
Steps to reproduce:
$ modprobe mlx5_core
$ ip netns add ns1
$ devlink dev reload pci/0000:08:00.0 netns ns1
$ ip netns del ns1
Resolve this by converting the notifier from per-devlink instance to
a static one registered during init phase and leaving it registered
forever. Use this notifier for all devlink port instances created
later on.
Note what a tree needs this fix only in case all of the cited fixes
commits are present.
Reported-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 565b4824c3 ("devlink: change port event netdev notifier from per-net to global")
Fixes: ee75f1fc44 ("net/mlx5e: Create separate devlink instance for ethernet auxiliary device")
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230510144621.932017-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer says:
====================
selftests: seg6: make srv6_end_dt4_l3vpn_test more robust
This pachset aims to improve and make more robust the selftests performed to
check whether SRv6 End.DT4 beahvior works as expected under different system
configurations.
Some Linux distributions enable Deduplication Address Detection and Reverse
Path Filtering mechanisms by default which can interfere with SRv6 End.DT4
behavior and cause selftests to fail.
The following patches improve selftests for End.DT4 by taking these two
mechanisms into account. Specifically:
- patch 1/2: selftests: seg6: disable DAD on IPv6 router cfg for
srv6_end_dt4_l3vpn_test
- patch 2/2: selftets: seg6: disable rp_filter by default in
srv6_end_dt4_l3vpn_test
====================
Link: https://lore.kernel.org/r/20230510111638.12408-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT4 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The srv6_end_dt4_l3vpn_test instantiates a virtual network consisting of
several routers (rt-1, rt-2) and hosts.
When the IPv6 addresses of rt-{1,2} routers are configured, the Deduplicate
Address Detection (DAD) kicks in when enabled in the Linux distros running
the selftests. DAD is used to check whether an IPv6 address is already
assigned in a network. Such a mechanism consists of sending an ICMPv6 Echo
Request and waiting for a reply.
As the DAD process could take too long to complete, it may cause the
failing of some tests carried out by the srv6_end_dt4_l3vpn_test script.
To make the srv6_end_dt4_l3vpn_test more robust, we disable DAD on routers
since we configure the virtual network manually and do not need any address
deduplication mechanism at all.
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEN9lkrMBJgcdVAPub1V2XiooUIOQFAmRbUnQACgkQ1V2XiooU
IOQNVw//eoCiid3J4TuNdzHaBHXUlZvln1n5Z6K5fIz5ytrY1T7oKC8Y9StkzzWR
29ToFLOJt1iRAcgxsghWRIwUzNwpuUdqgd9cUZMHMQxT0BJItp6FXUql2+1LkF/I
b/gnnb90zyE7lBS/VSRyOiqMiJlP+Som22d7Nn5k2KfTYEdXKwfzjsWAu3W3Sb0s
Lv/MA9DE42qcwiZubmFmDtOtAunPJFZm3HgkcAVeXoNkBDrSfkvxLIMYG6VfFNhQ
AkKMyzX293wpwVxfOuQfJr4QVlxAgOQUko+FqajoWMBtfA3yldZjJ8RC7c9Af9uI
ciOP11vHBCG84KrTabC5kdqOcvadreDiM/oIvk57ztQhCr3e+po+vIz6Cv4p9I30
m5GXfgbtMRl6hM2S5lrRc5fNRkYJHE4aNvesFTGaLpK3LogusH1E9mH5jdjnbU42
TwkIe250qJJelNn9ZxS5Jt0BgyogNfeiA9lOXmaQBpYmwIahrjDf0g8z2I85nPhF
PDukjSXsxi4uHwpSF5wFrlqkAPiEX4vC95uSUTVbbBgZrHhNJdGgu4FJSHRM4mVo
6Awxk2O2bvcDpXEfTBdD4EJF71bZ/aH2i8ddU1oupIl88O01TWTtkO4SYHqMX+tC
fPnpGzBN8KJvHgeFxO4p0v1oelv2RtiITv1gi7YJOnq/+Vd2yy0=
=HmfP
-----END PGP SIGNATURE-----
Merge tag 'nf-23-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter updates for net
The following patchset contains Netfilter fixes for net:
1) Fix UAF when releasing netnamespace, from Florian Westphal.
2) Fix possible BUG_ON when nf_conntrack is enabled with enable_hooks,
from Florian Westphal.
3) Fixes for nft_flowtable.sh selftest, from Boris Sukholitko.
4) Extend nft_flowtable.sh selftest to cover integration with
ingress/egress hooks, from Florian Westphal.
* tag 'nf-23-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
selftests: nft_flowtable.sh: check ingress/egress chain too
selftests: nft_flowtable.sh: monitor result file sizes
selftests: nft_flowtable.sh: wait for specific nc pids
selftests: nft_flowtable.sh: no need for ps -x option
selftests: nft_flowtable.sh: use /proc for pid checking
netfilter: conntrack: fix possible bug_on with enable_hooks=1
netfilter: nf_tables: always release netdev hooks from notifier
====================
Link: https://lore.kernel.org/r/20230510083313.152961-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima says:
====================
af_unix: Fix two data races reported by KCSAN.
KCSAN reported data races around these two fields for AF_UNIX sockets.
* sk->sk_receive_queue->qlen
* sk->sk_shutdown
Let's annotate them properly.
====================
Link: https://lore.kernel.org/r/20230510003456.42357-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's been a few years since we've sorted this thing, and the end result
is that we've added MAINTAINERS entries in the wrong order, and a number
of entries have their fields in non-canonical order too.
So roll this boulder up the hill one more time by re-running
./scripts/parse-maintainers.pl --order
on it.
This file ends up being fairly painful for merge conflicts even
normally, since unlike almost all other kernel files it's one of those
"everybody touches the same thing", and re-ordering all entries is only
going to make that worse. But the alternative is to never do it at all,
and just let it all rot..
The rc2 week is likely the quietest and least painful time to do this.
Requested-by: Randy Dunlap <rdunlap@infradead.org>
Requested-by: Joe Perches <joe@perches.com> # "Please use --order"
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmRcFLAACgkQnJ2qBz9k
QNmSuQf+P+hFOHVpCb83S4TrNsfPC9M7Pv/M1Rw926p1gESNLez1ElAx2B35OIBZ
y4ijqrSHgXbCsC3PvbxR9YfBPJZwIhtmKwjPC+9KlhAFB536Bvt/nt34fjRCWJiS
nABnexegkirk7EQufAGVZQ1gtm1p0qSCA1B/l5AFl4KeLIin31U/08F2eE1OAo3K
TmxhXzlC+JRXjf/X/X8mzJ8nz/hY5039BDvs7EpVdOsZcLFRQcCUygUCrOdV94uI
1wyzMoGNaiIsZHpHPf3NtphUoE9IFpZQJGXMTR4ehBgFYkkOHYxsjW+wn8YOmaks
qzRRXb9w0WdgAXChDGu1xYXV6Wpjiw==
=kqSe
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull inotify fix from Jan Kara:
"A fix for possibly reporting invalid watch descriptor with inotify
event"
* tag 'fsnotify_for_v6.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
inotify: Avoid reporting event with invalid wd
On corrupt gfs2 file systems the evict code can try to reference the
journal descriptor structure, jdesc, after it has been freed and set to
NULL. The sequence of events is:
init_journal()
...
fail_jindex:
gfs2_jindex_free(sdp); <------frees journals, sets jdesc = NULL
if (gfs2_holder_initialized(&ji_gh))
gfs2_glock_dq_uninit(&ji_gh);
fail:
iput(sdp->sd_jindex); <--references jdesc in evict_linked_inode
evict()
gfs2_evict_inode()
evict_linked_inode()
ret = gfs2_trans_begin(sdp, 0, sdp->sd_jdesc->jd_blocks);
<------references the now freed/zeroed sd_jdesc pointer.
The call to gfs2_trans_begin is done because the truncate_inode_pages
call can cause gfs2 events that require a transaction, such as removing
journaled data (jdata) blocks from the journal.
This patch fixes the problem by adding a check for sdp->sd_jdesc to
function gfs2_evict_inode. In theory, this should only happen to corrupt
gfs2 file systems, when gfs2 detects the problem, reports it, then tries
to evict all the system inodes it has read in up to that point.
Reported-by: Yang Lan <lanyang0908@gmail.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Highlights:
- thinkpad_acpi: Fix profile (performance/bal/low-power) regression on T490
- misc. other small fixes / hw-id additions
The following is an automated git shortlog grouped by driver:
hp-wmi:
- add micmute to hp_wmi_keymap struct
intel_scu_pcidrv:
- Add back PCI ID for Medfield
platform/mellanox:
- fix potential race in mlxbf-tmfifo driver
platform/x86/intel-uncore-freq:
- Return error on write frequency
thinkpad_acpi:
- Add profile force ability
- Fix platform profiles on T490
touchscreen_dmi:
- Add info for the Dexp Ursus KX210i
- Add upside-down quirk for GDIX1002 ts on the Juno Tablet
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmRbcQ4UHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9yFnQf9G83wo2B5SfjN7V7viYHEGB4InfQL
+MbhwP+Efe++BkxwAzVMcVLSuYOsbqcrRBCiQkBVCyAF14LVVH3ymnn/upoqz9l4
K4JUZorGIEPgl0SpGP+41j+P93XYfcfMYPRetZA8ErBpitSfHVf9oAG8vTgaemda
Qxo8DWs4R1WGdg8KZ7icZ7shXiyzIeGBnQB/5EzpBrv6v6EmiJsUZh5ZZASOidrg
IXTp8LgLhkFbIQBgHoOyHoM7puRI7MRbxu5YEJ+wKumFi4KmuTET5iDlZFpmqvoH
eAU/JUWIsQ3I1QwTKFSLFYkJZCZrIIJHew1Lvs9F+/x1c2vs1QjOG8RoEg==
=SEuW
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Nothing special to report just various small fixes:
- thinkpad_acpi: Fix profile (performance/bal/low-power) regression
on T490
- misc other small fixes / hw-id additions"
* tag 'platform-drivers-x86-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/mellanox: fix potential race in mlxbf-tmfifo driver
platform/x86: touchscreen_dmi: Add info for the Dexp Ursus KX210i
platform/x86: touchscreen_dmi: Add upside-down quirk for GDIX1002 ts on the Juno Tablet
platform/x86: thinkpad_acpi: Add profile force ability
platform/x86: thinkpad_acpi: Fix platform profiles on T490
platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct
platform/x86/intel-uncore-freq: Return error on write frequency
platform/x86: intel_scu_pcidrv: Add back PCI ID for Medfield
Commit d4c3676507 ("net: mscc: ocelot: keep ocelot_stat_layout by reg
address, not offset") organized the stats counters for Ocelot chips, namely
the VSC7512 and VSC7514. A few of the counter offsets were incorrect, and
were caught by this warning:
WARNING: CPU: 0 PID: 24 at drivers/net/ethernet/mscc/ocelot_stats.c:909
ocelot_stats_init+0x1fc/0x2d8
reg 0x5000078 had address 0x220 but reg 0x5000079 has address 0x214,
bulking broken!
Fix these register offsets.
Fixes: d4c3676507 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the chapter heading for "X.25 Device Driver Interface" so that it
does not contain a trailing '-' character, which makes Sphinx
omit this heading from the contents.
Reverse the order of the x25.rst and x25-iface.rst files in the index
so that the project introduction (x25.rst) comes first.
Fixes: 883780af72 ("docs: networking: convert x25-iface.txt to ReST")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: linux-x25@vger.kernel.org
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.
Fixes: 5e8c5adf95 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
