Allow the subdevice to be probed asynchronously.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver was written with the 'soc_camera' use in mind, however the g_std()
video method was forgotten. Implement it at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
drivers/media/i2c/tc358743.c:1960:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hardware interrupts are enabled in the probe function, before the subdev
is registered to its v4l2_device. Until v4l2_device_register_subdev_node
is called, sd->devnode is NULL and v4l2_subdev_notify_event must not be
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by Randy:
> when CONFIG_MEDIA_CONTROLLER is not enabled:
>
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
> ../drivers/media/i2c/tc358743.c:1890:29: error: 'struct v4l2_subdev' has no member named 'entity'
> err = media_entity_init(&sd->entity, 1, &state->pad, 0);
> ^
> ../drivers/media/i2c/tc358743.c:1940:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_remove':
> ../drivers/media/i2c/tc358743.c:1955:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
This driver depends on VIDEO_V4L2_SUBDEV_API and needs to select HDMI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
specified in the device tree binding documentation that the reset gpio
is optional. Make the implementation match accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
failed to explicitly set the direction of the reset gpio. Use the
optional flag of devm_gpiod_get to make up leeway.
This is also necessary because the flag parameter will become mandatory
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Header claims GPL v2, so make the MODULE_LICENSE reflect that properly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sr030pc30_get_fmt() can only succeed if both info->curr_win and
info->curr_fmt are not NULL.
If one of those vars are null, the curent code would call:
ret = sr030pc30_set_params(sd);
If the curr_win is null, it will return -EINVAL, as it would be
expected. However, if curr_fmt is NULL, the function won't
set it.
The code will then try to read from it:
mf->code = info->curr_fmt->code;
mf->colorspace = info->curr_fmt->colorspace;
with obviouly won't work.
This got reported by smatch:
drivers/media/i2c/sr030pc30.c:505 sr030pc30_get_fmt() error: we previously assumed 'info->curr_win' could be null (see line 499)
drivers/media/i2c/sr030pc30.c:507 sr030pc30_get_fmt() error: we previously assumed 'info->curr_fmt' could be null (see line 499)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Why to store the chosed values for prediv, postdiv and mult if
those won't be used?
drivers/media/i2c/ov2659.c: In function 'ov2659_pll_calc_params':
drivers/media/i2c/ov2659.c:912:35: warning: variable 's_mult' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:20: warning: variable 's_postdiv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:6: warning: variable 's_prediv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
This is likely some leftover from some past change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:148:19: warning: Variable length array is used.
As the maximum size is 1026, we can't use dynamic var, as it
would otherwise spend 1056 bytes of the stack at i2c_wr() function.
So, allocate a buffer with the allowed maximum size together with
the state var.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the i2c devices menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’:
CC [M] drivers/media/i2c/s5k4ecgx.o
drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (pdata && pdata->link_freqs) {
^
It can indeed be uninitialized in one corner case. Initialize to NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using adv7611_read_cable_det() for ADV7612 means that full
support for '.max_port = ADV7604_PAD_HDMI_PORT_B,' isn't available
due to the need for multiple port reads to determine cable detection,
and an agreed mechanism for communicating the separate statuses.
This patch replaces adv7611_read_cable_det() with a functionally
identical copy, commented appropriately.
Earlier submissions [leading to commit 8331d30b] also set .cp_csc,
which is used in a cp_read() call within adv76xx_log_status().
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prior to commit f862f57d ("[media] media: i2c: ADV7604: Migrate to
regmap"), the local variable 'val' contained the combined register
reads used in the chipset version ID test. Restore this expectation
so that the comparison works as it used to.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The JPEG colorspace should only be used for JPEG encoded images. This is
just a regular sRGB sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify confusing conditions. This also swaps the checks for NTSC and PAL:
to be consistent with other drivers check for NTSC first. So if the user
sets both NTSC and PAL bits, then NTSC wins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the standard changes the VACTIVE and VDELAY values need to be updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is an SDTV video receiver, so the colorspace should be SMPTE170M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The zoran driver has now been converted to the control framework
which means that these three subdevice drivers no longer need to
support the legacy core control ops since the last bridge driver
that needed that has now been converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bt pointer was never used, remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is useful to subscribe to HDMI hotplug events via the
V4L2_CID_DV_RX_POWER_PRESENT control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When probed from device tree, the i2c client driver can handle the interrupt
on its own.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for probing the TC358743 subdevice from device tree.
The reference clock must be supplied using the common clock bindings.
MIPI CSI-2 specific properties are parsed from the OF graph endpoint
node and support for a non-continuous MIPI CSI-2 clock is added.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add V4L2_SUBDEV_FL_HAS_DEVNODE to subdev flags, in order to
enable a subdev device node.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver is tested on our hardware and all the implemented features
works as expected.
Missing features:
- CEC support
- HDCP repeater support
- IR support
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
[hans.verkuil@cisco.com: updated copyright year to 2015]
[hans.verkuil@cisco.com: update confusing confctl_mutex comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of VIDEO_ADV7604 and VIDEO_COBALT (the latter
selects the former) on GPIOLIB if COMPILE_TEST is enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support to the adv7604 driver for specifying the default input
port in the Device tree. If no value is provided, the driver will be
unable to select an input without help from userspace.
Tested-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the ADV7612 chip as implemented on Renesas' Lager
board to adv7604.c, including lists for formats/colourspace/timing
selection and an IRQ handler.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix merge conflicts due to regmap patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preliminary patch in order to add support for ALSA.
It replaces all current i2c access with regmap.
Signed-off-by: Pablo Anton <pablo.anton@veo-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a proper of match id for use when the device is being bound via
device tree, to avoid having to use the i2c old-style binding of the
device.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: William.Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without setting the direction of a gpio to output a call to
gpiod_set_value doesn't have a defined outcome.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
In little endian cases, macro cpu_to_be16 unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_cpu_to_be16 and cpu_to_be16 expand directly to the
same expression. So, replace __constant_cpu_to_be16 with
cpu_to_be16 with the goal of getting rid of the definition of
__constant_cpu_to_be16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The subdev API is optional. No driver should depend on it.
Avoid compilation breakages if subdev API is not selected:
drivers/media/i2c/ov2659.c: In function ‘ov2659_get_fmt’:
drivers/media/i2c/ov2659.c:1054:3: error: implicit declaration of function ‘v4l2_subdev_get_try_format’ [-Werror=implicit-function-declaration]
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c:1054:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_set_fmt’:
drivers/media/i2c/ov2659.c:1129:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_open’:
drivers/media/i2c/ov2659.c:1264:38: error: ‘struct v4l2_subdev_fh’ has no member named ‘pad’
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Log the alternate gamma state and the HDMI colorspace that the adv
device detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logging of the saturator status was wrong due to an incorrect
condition.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for logging the detected InfoFrames for the adv76xx. Helps in
debugging what is actually received on the HDMI link.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7511 sets up InfoFrames that are used when transmitting video.
Log the contents of those InfoFrames so it is possible to see exactly what
the transmitter is sending.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u32 and uint8_t/uint32_t. Standardize on
u8/u32.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u16 and uint8_t/uint16_t. Standardize on
u8/u16.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Still preliminary, but the information is at least there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7604 driver depends on GPIOLIB, and therefore cobalt depends
on it as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes it easier for the bridge driver to just passthrough such
events to the corresponding device node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Copied from the adv7604 driver.
Note: while arch/blackfin/mach-bf609/boards/ezkit.c uses adv7842_platform_data
this source has not been updated because it is broken since the very
beginning. It depends on a struct adv7842_output_format that does not
exist.
And besides that gcc has no support for bf609 so nobody can compile it
except by installing a toolchain from ADI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Bellow is yelling. Ok, sometimes the code is yells a lot, but
but this is not the case there ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The try_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Since try_mbus_fmt and s_mbus_fmt both map to the set_fmt pad op (but
with a different 'which' argument), this patch will replace both
try_mbus_fmt and s_mbus_fmt by set_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The g_mbus_fmt video op is a duplicate of the pad op. Replace all uses
by the get_fmt pad op and remove the video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to the enum_mbus_fmt video op by the pad
enum_mbus_code op and remove the duplicate video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the format is Y'CbCr, the colorspace used by the sensor
is almost certainly SRGB. The sensor is also not generating JPEG data,
so it makes no sense to use V4L2_COLORSPACE_JPEG here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The width and height should be checked in the enum_frame_interval
op. This fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This needs to be signed or there is a risk of hitting a forever loop.
Fixes: c4c0283ab3 ('[media] media: i2c: add support for omnivision's ov2659 sensor')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All masks for timings are different between ADV7604 and ADV7611.
Most of the values have 1 precision bit more in the latter.
Fix this by adding new fields to the chip_info structure.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov7670_s_exp() checks read error for 2 registers: REG_COM1
and REG_COM8. But, although it uses the value latter, it
doesn't check errors on REG_AECHH read. Yet, as it is doing
a bitmask operation there, the read operation should succeed.
So, fix the code to also check if this succeeded.
This fixes this smatch report:
drivers/media/i2c/ov7670.c:1366 ov7670_s_exp() warn: inconsistent indenting
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
This is done right at saa717x_write(), but the read function is
broken. Thankfully, there's just one place at saa717x driver that
uses multibyte read (for status report, via printk).
Yet, let's fix it. From saa717x_write(), it is clear that the
bytes are in little endian:
mm1[4] = (value >> 16) & 0xff;
mm1[3] = (value >> 8) & 0xff;
mm1[2] = value & 0xff;
So, the same order should be valid for read too.
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_set_power':
drivers/media/i2c/s5k5baf.c:1057:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on != state->power)
^
drivers/media/i2c/s5k6aa.c: In function 's5k6aa_set_power':
drivers/media/i2c/s5k6aa.c:878:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == s5k6aa->power) {
^
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function 's5c73m3_oif_set_power':
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1456:17: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
} else if (!on == state->power) {
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support for adp1653 flash LED driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As requested by Sakari:
"The driver changes are still being reviewed.
It's been proposed that the max-microamp property be renamed."
So, as the DT bindings are not agreed upstream yet, let's revert
it.
Requested-by: Sakari Ailus <sakari.ailus@iki.fi>
This reverts commit b6100f10bd.
Nokia N900 is switching to device tree, make sure we can use flash
there, too.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch add a missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't rely on V4L2_DV_BT_STD_CEA861 since that include the
640x480p format, which is an IT format, not CE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't set rval when it's not used (the function returns a pointer to struct
smiapp_platform_data).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for omnivision's ov2659
sensor, the driver supports following features:
1: Asynchronous probing
2: DT support
3: Media controller support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The documentation stated that the link-frequencies property belongs to the
endpoint node, not to the device's of_node. Fix this.
There are no DT board descriptions using the driver yet, so a fix in the
driver is sufficient.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Parse DT properties into a platform data structure when a DT node is
available.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device requires control to be properly operated, they're not
optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both synchronous and asynchronous mt9p031 subdevice probing
is supported by this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure to call mutex_destroy() in case of probe failure or module
unload.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There must be used 'min_t', not 'max_t' for calculating the divider.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support for ov2640.
In device tree, user needs to provide the master clock (xvclk).
User can add the reset/pwdn pins if they have.
Cc: devicetree@vger.kernel.org
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In async probe, there is a case that ov2640 is probed before the
host device which provided 'mclk'.
To support this async probe, we will get 'mclk' at first in the probe(),
if failed it will return -EPROBE_DEFER. That will let ov2640 wait for
the host device probed.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
pixel_order_str is only referred to in smiapp-core.c, it should be thus
static. Thanks to Hans Verkuil for pointing this out.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_property_read_u64_array() wasn't yet part of the kernel tree when the
functionality was needed. Do use it now.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_interval ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Tested for ov7670 and marvell-ccic on a OLPC XO-1 laptop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_size ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify accordingly.
Moreover use devm_gpiod_get_index_optional instead of
devm_gpiod_get_index with ignoring all errors.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops module param 'debug' as it was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers are moved to support asynchronous probing,
v4l2_async_unregister_subdev() unregisters the subdev so
there isn't a need to explicitly call v4l2_device_unregister_subdev().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace dev_err statement with pr_err to fix null dereference.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is confusing which parts of the driver are adv7604 specific, adv7611
specific or common for both. This patch renames any adv7604 prefixes (both
for functions and defines) to adv76xx whenever they are common.
Signed-off-by: Pablo Anton <pablo.anton@vodalys-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: rebased and renamed ADV76xx_fsc to ADV76XX_FSC]
[hans.verkuil@cisco.com: kept the existing adv7604 driver name]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bits are the same, but register is 0xf4 on ADV7611 instead of 0xfc.
When reading back the value in log_status, differentiate both.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The CP_NON_STD_VIDEO bit indicates an input not aligned with DV timings.
If there is no input, and chip is in free run mode, consider we are locked.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: put both conditions in one 'if']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use an enum to better document the media pads.
No functional changes.
Suggested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no need to free state, as it was allocated via devm_kzalloc().
Also, let's return the error code, instead of something else.
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Analog video inputs are the tuner, plus composite, svideo, etc,
e. g. the input pat should actually be like:
___________
TUNER --------> | |
| |
SVIDEO .......> | cx25840 |
| |
COMPOSITE1 ...> |_________|
(in the above, dashes represent the enabled link, and periods
represent the disabled ones)
In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.
I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
drivers, in order to represent what of the possible internal
inputs are actually used on each specific board
Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of keeping the media controller entity not initialized,
fill it and create the pads for cx25840.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.
The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.
I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.
The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.
As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.
Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.
Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reset the device when initializing it so it is in a good known state and the
assumed register settings matches the actual register settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.
This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.
Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reuse the v4l2 size definitions from v4l2-image-sizes.h.
So we can remove the rudundent definitions from ov2640.c.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_read_number() is defined in of.h but does not return an error code, so
that non-of implementation could simply return an error.
Temporarily work around this until of_read_number() can be replaced by
of_property_read_u64_array().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new logging functions from the hdmi module.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
vblanking() hblanking()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the macros a little bit safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As the controls creation is separated in two sections, the available media
bus codes and link frequencies can be enumerated later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.
[mchehab@osg.samsung.com: make checkpatch.pl happier]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Also call smiapp_cleanup() in smiapp_remove(), replacing code that did the
same than the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flash capability register is already read as part of the limit
registers. Do no access it separately; instead use the value from the
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform data support is retained.
of_property_read_u64_array() isn't used yet as it's not in yet.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SMIA compatible sensors only need a single clock.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The source sub-device's name will be overwritten shortly. Don't give it a
name in the meantime.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct device has a forward declaration in the header already. The header is
only needed in the .c file.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Timo Ahonen <timo.ahonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:344:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:354:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:364:24: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:366:23: warning: cast to restricted __le16
The get_unaligned_le*() functions return the value using cpu endianness,
so calling le*_to_cpu is wrong.
It hasn't been not noticed because this code has only been run on little
endian systems, so le*_to_cpu doesn't do anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers depend on VIDEO_V4L2_SUBDEV_API, which in turn
depends on MEDIA_CONTROLLER. So it is sufficient to just depend
on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rPM
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second set of media updates from Mauro Carvalho Chehab:
- Move drivers for really old legacy hardware to staging. Those are
using obsolete media kAPIs and are for hardware that nobody uses for
years. Simply not worth porting them to the new kAPIs. Of course,
if anyone pops up to fix, we can move them back from there
- While not too late, do some API fixups at the new colorspace API,
added for v3.19
- Some improvements for rcar_vin driver
- Some fixups at cx88 and vivid drivers
- Some Documentation fixups
* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
[media] tlg2300: move to staging in preparation for removal
[media] vino/saa7191: move to staging in preparation for removal
[media] MAINTAINERS: vivi -> vivid
[media] cx88: remove leftover start_video_dma() call
[media] cx88: add missing alloc_ctx support
[media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
[media] vivid: fix CROP_BOUNDS typo for video output
[media] DocBook media: update version number and document changes
[media] vivid.txt: document new controls
[media] DocBook media: add missing ycbcr_enc and quantization fields
[media] v4l2-mediabus.h: use two __u16 instead of two __u32
[media] rcar_vin: Fix interrupt enable in progressive
[media] rcar_vin: Enable VSYNC field toggle mode
[media] rcar_vin: Add scaling support
[media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
[media] rcar_vin: Add YUYV capture format support
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
Add support for selection target V4L2_SEL_TGT_NATIVE_SIZE. It is equivalent
of what V4L2_SEL_TGT_CROP_BOUNDS used to be. Support for
V4L2_SEL_TGT_CROP_BOUNDS is still supported by the driver as a compatibility
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fields were previously uninitialised, leaving the returned values to
where the user had set them. This was never the intention.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for YCbCr output and support setting colorspace,
YCbCr encoding and quantization for the AVI InfoFrame.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rc_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have v4l2-compliance tool pass the G/S_EDID some modifications
where needed in the driver.
In particular, the edid.reserved zone must be blanked.
Based on a patch from Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>,
but reworked it a bit. It should use 'data' (which depends on edid.present)
instead of edid.blocks as the check whether edid data is present.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the v4l2-compliance failures.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this pass the v4l2-compliance test.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
This use has a mask then shift which is not the normal style.
Move the shift before the mask to match nearly all the other
uses in kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to report:
cx25840 7-0044: Firmware download size changed to 16 bytes max length
If the driver needs to adjust the buffer's maximum size.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media bus format BPP does affect PLL. Recalculate PLL if the format
changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set supported link frequencies in the menu in control initialisation and
when the bpp changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
smiapp_set_format() has accumulated a fair amount of changes without a
needed refactoring, do the cleanup now. There's also an unlocked version of
v4l2_ctrl_range_changed(), using that fixes a small serialisation issue with
the user space interface.
__v4l2_ctrl_modify_range() is used instead of v4l2_ctrl_modify_range() in
smiapp_set_format_source() since the mutex is now held during the function
call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some media bus codes may be unavailable depending on the available media bus
codes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all link rates are possible with all BPP values.
Also rearrange other initialisation a little. Obtaining possible PLL
configurations earlier requires that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The first one is handy for just trying out a PLL configuration without a
need to apply it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The actual pixel array pixel rate may be something else than vt_pix_clk_freq
on some implementations. Add a new field which contains the corrected value.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
op_pix_clk_div is directly assigned and not calculated. There's no need to
verify it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to pretend the OP limits are there anymore.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For profile 0 sensors (which have no OP clocks), the OP limits are in fact
VT limits. Do not verify them again.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Profile 0 sensors have no OP clock branck in the clock tree. The PLL
calculator still calculated them, they just weren't used for anything.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Uniform representation for VT and OP clocks. This is preparation for
calculating the VT clocks using the OP clock code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enough work for this function already.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These values are unsigned, so use %u instead of %d.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The PLL flags were not used correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex does not serialise anything in this case but avoids a lockdep
warning from the control framework.
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.
In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Test for definedness of the macro which is actually defined, and which
matches the name of the file.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ensures device->streaming has correct status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Instead of using if (on == true), just use
if (on).
That allows a faster mental parsing when analyzing the
code.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The smiapp driver is the owner of the sub-devices exposed by the smiapp
driver. This prevents unloading the module whilst it's in use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor may be powered by either one of its sub-devices being accessed
from the user space (an open file handle) or by its s_power() op being
called with non-zero on argument. The driver counts the users and if any
reason to keep the device powered exists it will be powered.
However, a faulty condition was used in recognising the need to power off
the sensor, leading it to be powered off every time any of its uses went
away.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix a copy-paste bug when converting to the control framework.
Fixes: commit 5d478e0de8 ("[media] tda7432: convert to the control framework")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of modifying the control ranges directly by manipulating struct
v4l2_ctrl, use __v4l2_ctrl_modify_range() for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the V4L2_CID_TEST_PATTERN control. When the solid colour
mode is selected, additional controls become available for setting the
solid four solid colour components.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add device-tree support for mt9m111 camera sensor.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
X-Patchwork-Delegate: mchehab@redhat.com
The driver mistakenly prints the ROM version instead of the device ID to
the kernel log when detecting the chip. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SMIA++ sensors are progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
as are mt9v024 and mt9v034. With minimal changes it is possible
to support mt9v02[24] with the same driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The read mode register bits 8 and 9 are set and marked as reserved.
Don't clear them.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the recommended writes to those mentioned in the Rev 1.5 version of the
ADV7611 Register Settings Recommendations document released by Analog Devices.
The document does not mention why the recommended settings have been updated,
but presumably those are more fine tuned settings that can enhance performance
in some cases.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull updates and DT support for media engines from Mauro Carvalho Chehab.
For Analog Devices ADV7604 and the Renesas VSP1 video processing engines.
* 'topic/vsp1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Add DT support
[media] v4l: vsp1: Add DT bindings documentation
[media] v4l: vsp1: Add BRU support
[media] v4l: vsp1: Support multi-input entities
[media] v4l: vsp1: uds: Enable scaling of alpha layer
[media] v4l: vsp1: Remove unexisting rt clocks
* 'topic/adv76xx' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (21 commits)
[media] adv7604: Add LLC polarity configuration
[media] adv7604: Set HPD GPIO direction to output
[media] adv7604: Add endpoint properties to DT bindings
[media] adv7604: Add DT support
[media] adv7604: Specify the default input through platform data
[media] adv7604: Support hot-plug detect control through a GPIO
[media] adv7604: Sort headers alphabetically
[media] adv7604: Replace *_and_or() functions with *_clr_set()
[media] adv7604: Store I2C addresses and clients in arrays
[media] adv7604: Inline the to_sd function
[media] v4l: subdev: Remove deprecated video-level DV timings operations
[media] adv7604: Remove deprecated video-level DV timings operations
[media] adv7604: Add pad-level DV timings support
[media] adv7604: Make output format configurable through pad format operations
[media] adv7604: Add sink pads
[media] adv7604: Remove subdev control handlers
[media] adv7604: Add adv7611 support
[media] adv7604: Cache register contents when reading multiple bits
[media] adv7604: Add 16-bit read functions for CP and HDMI
[media] adv7604: Don't put info string arrays on the stack
...
The include/media/s5p_fimc.h header has been removed in commit
49b2f4c56f ("exynos4-is: Remove support
for non-dt platforms"). This broke compilation of the m5mols driver.
Include the include/media/exynos-fimc.h header instead, which contains
the S5P_FIMC_TX_END_NOTIFY definition required by the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This one line function is called in a single location. Inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Control operations are handled by the control framework and the subdev
control handlers are never called directly. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When extracting multiple bits from a single register read the register
once and extract the bits on the read value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
16-bit registers are read through two 8-bit read operations. Factorize
that common pattern into 16-bit read accessors to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We do not want to modify the info string arrays ever, so no need to
waste stack space for them. While we are at it also make them const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Register the device with the v4l2 asynchronous probing framework to
support asynchronous instantiation systems such as DT.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The subdev EDID ioctls receive a pad field that must reference an
existing pad and an EDID field that must point to a buffer. Validate
both fields in the core code instead of duplicating validation in all
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated. Implement the
pad-level version of the operation to prepare for the removal of the
video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the driver-specific inline function to cast from a subdev pointer to
a tvp5150 pointer instead of the generic container_of().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Auto BLC and BLC digital offset are disabled when enabling the test
pattern and must be restored when disabling it. The driver does so by
calling the set control handler on the auto BLC and BLC offset controls,
but this programs the hardware with the new value of those controls, not
the current value. Fix this by writing to the registers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The digital side of the Black Level Calibration (BLC) function must be
disabled when generating a test pattern to avoid artifacts in the image.
The driver disables BLC correctly at the hardware level, but the feature
gets reenabled by v4l2_ctrl_handler_setup() the next time the device is
powered on.
Fix this by marking the BLC controls as inactive when generating a test
pattern, and ignoring control set requests on inactive controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prepare for supporting systems using the Device tree. Should the resources
not be available at the time of driver probe(), the EPROBE_DEFER error code
must be also returned from its probe function.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do not use our special value, SMIAPP_NO_XSHUTDOWN.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "best" value was unsigned however, leading to signed-to-unsigned
comparison and wrong results. Possibly only on a newer GCC. Fix this by
making the best value signed as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some of the limits are used before the limits quirk is called. Move the call
immediately after obtaining the limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 75e2bdad89 "ov7670: allow
configuration of image size, clock speed, and I/O method" uses a wrong
index to iterate an array. Apart from being wrong, it also uses an
unchecked value from user-space, which can cause access to unmapped
memory in the kernel, triggered by a normal desktop user with rights to
use V4L2 devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register address, width and flags are encoded as a 32-bit value. Add
macros for obtaining these separately. Use the macros in register access
functions.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a quirk for diverting registers for on some sensors, even the standard
registers are not where they can be expected to be found. Add a quirk to
to help using such sensors.
smiapp_write_no_quirk() and smiapp_read_no_quirk() functions are provided
for the use of quirk implementations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is more flexible. Quirk flags may be affected by configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No reason to keep this u8, really.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to just copy the information to the PLL flags. Add a
new fields for the quirks to contain the PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sub-device names should be unique. Should two identical sensors be
present in the same media device they would be indistinguishable. The names
will change e.g. from "vs6555 pixel array" to "vs6555 1-0010 pixel array".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
8-bit reads are needed in some cases; however the condition used was wrong.
Regular access (register width) was used if:
len == SMIAPP_REG_8BIT && !only8
This causes 8-bit read access to be used always. The operator should be ||
instead: regular access can be used for 8-bit reads OR if allowed otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SMIAPP_REG_ is the common prefix used in the driver for register related
definitions. Use it consistently.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The quirk registers mechanism which allows register to have a static read
access value from the sensor specific quirks, is not used. Remove it. It is
to be replaced by a more generic register diversion quirk soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This fixes following build error:
CC drivers/media/i2c/s5c73m3/s5c73m3-core.o
CC drivers/md/dm-ioctl.o
CC net/ipv4/inet_lro.o
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function ‘s5c73m3_get_platform_data’:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:2: error: implicit declaration of function ‘v4l2_of_get_next_endpoint’ [-Werror=implicit-function-declaration]
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:10: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
There is request_irq() in init_device(), but the interrupt is not removed
on failure paths. The patch adds proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the V4L2 asynchronous subdev registration and
device tree support. Common clock API is used to control the
sensor master clock from within the subdev.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
