Enable HiSilicon SAS controller based on PCI device,
which is included in hip08 SoC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The Allwinner A64 SoC is paired with the X-Powers AXP803 PMIC over the
Reduced Serial Bus (RSB). The regulators of this PMIC supply all power
rails of the SoC and many external peripherals.
Enable the driver for the regulators of this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner A64 SoC is paired with the X-Powers AXP803 PMIC over the
Reduced Serial Bus (RSB).
Enable the driver for this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: Refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Make the rockchip PHY driver built into the kernel.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests showed, that under certain conditions, the summary number of jiffies
spent on softirq/idle, which are counted by system statistics can be even
below 10% of expected value, resulting in false load presentation.
The issue was observed on the quad-core Marvell Armada 8k SoC, whose two
10G ports were bound into L2 bridge. Load was controlled by bidirectional
UDP traffic, produced by a packet generator. Under such condition,
the dominant load is softirq. With 100% single CPU occupation or without
any activity (all CPUs 100% idle), total number of jiffies is 10000 (2500
per each core) in 10s interval. Also with other kind of load this was
true.
However below a saturation threshold it was observed, that with CPU which
was occupied almost by softirqs only, the statistic were awkward. See
the mpstat output:
CPU %usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
all 0.00 0.00 0.13 0.00 0.00 0.55 0.00 0.00 0.00 99.32
0 0.00 0.00 0.00 0.00 0.00 23.08 0.00 0.00 0.00 76.92
1 0.00 0.00 0.40 0.00 0.00 0.00 0.00 0.00 0.00 99.60
2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00
3 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00
Above would mean basically no total load, debug CPU0 occupied in 25%.
Raw statistics, printed every 10s from /proc/stat unveiled a root
cause - summary idle/softirq jiffies on loaded CPU were below 200,
i.e. over 90% samples lost. All problems were gone after enabling
fine granulity IRQ time accounting.
This patch fixes possible wrong statistics processing by enabling
CONFIG_IRQ_TIME_ACCOUNTING for arm64 platfroms, which is by
default done on other architectures, e.g. x86 and arm. Tests
showed no noticeable performance penalty, nor stability impact.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The hardware spinlock drivers now depend on HWSPINLOCK (instead of
selecting it), so we need to explicitly enable it after commit
35fc8a07d7 ("Make HWSPINLOCK a menuconfig to ease disabling")
Without HWSPINLOCK, various drivers are left with unsatisfied
dependencies and Qcom boards using shared memory based communication
to request regulators are failing to boot and mount rootfs.
Fix this by explicitly enabling HWSPINLOCK in defconfig.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Compile the renesas sound and ak4613 drivers as modules to reduce the ARM64
kernel size. These modules are currently only used by Renesas platforms so
there should little risk of negative impact of this change on other users.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[simon: consolidated two patches into one]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit enables the nop-xceiv PHY driver, which is needed for USB
support to work on the MacchiatoBin platform (Marvell Armada 8K).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek RTD1295
and Action Semi S900. Both are fairly similar chips, used mainly in
set-top-boxes, but with other possible applications, and additional
members in the respective product families that could be added in the
future. The code here is fairly minimal, as all the interesting parts
are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=771F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek
RTD1295 and Action Semi S900. Both are fairly similar chips, used
mainly in set-top-boxes, but with other possible applications, and
additional members in the respective product families that could be
added in the future. The code here is fairly minimal, as all the
interesting parts are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: remove duplicate entry
arm64: defconfig: enable Qualcomm Technologies EMAC and some PHY drivers
arm64: defconfig: enable QCOM_L2_PMU and QCOM_L3_PMU
arm64: defconfig: enable EDAC options
arm64: defconfig: enable APEI and GHES features
arm64: defconfig: enable support for PCIe hotplug
arm64: defconfig: enable EFI_CAPSULE_LOADER
arm64: defconfig: enable BLK_DEV_NVME
arm64: defconfig: enable ACPI_CPPC_CPUFREQ
arm64: marvell: enable ICU and GICP drivers
arm64: marvell: enable the Armada 7K/8K pinctrl driver
arm64: Prepare Actions Semi S900
ARM64: defconfig: enable meson SPICC as module
ARM64: defconfig: enable IR core, decoders and Meson IR device
arm64: defconfig: enable Simple Sound Card support
arm64: defconfig: Enable ARCH_BRCMSTB
arm64: defconfig: drop ARCH_VULCAN
arm64: disable Broadcom Vulcan platform
MAINTAINERS: Add Realtek section
ARM64: Prepare Realtek RTD1295
The EMAC is present on Qualcomm Technologies' server and some mobile
chips, and is used as the primary Ethernet interface.
Systems that have these SOCs typically have an Atheros 803x or
Marvell 88e1111 PHY in them, so enable those drivers too.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the drivers are available, enable support for L2 and L3
performance monitoring Qualcomm Datacenter Technologies Centriq SoCs.
These PMU drivers provide support for performance optimization.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable EDAC (Error Detection and Correction) support for ARM64 server
systems that feature it, so that user space applications can be
notified of memory errors.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM64 server platforms can support ACPI Platform Error Interface (APEI)
and Generic Hardware Error Source (GHES) features, so enable them.
Platforms which support the firmware-first RAS error reporting model
require APEI and GHES functionality for the OS to receive and report
error records provided by the platform.
PCIe AER functionality is required for PCIe AER errors to be properly
reported and recovered from.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some ARM64 server systems support PCIe hotplug, so enable the options
for that.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_EFI_CAPSULE_LOADER allows the user to update the EFI firmware,
which is useful on ARM64 server platforms.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
NVME is non-volatile storage media attached via PCIe. NVME devices
typically have much higher potential throughput than other block
devices, like SATA, NVME is a must-have requirement for ARM64 based
servers.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The CPPC CPUFreq driver is used on many ACPI-based ARM64 server systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- enable meson SPICC as module
- enable IR core, decoders and Meson IR device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MTfE
-----END PGP SIGNATURE-----
Merge tag 'amlogic-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/arm64
Amlogic arm64 defconfig changes for v4.13
- enable meson SPICC as module
- enable IR core, decoders and Meson IR device
* tag 'amlogic-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: defconfig: enable meson SPICC as module
ARM64: defconfig: enable IR core, decoders and Meson IR device
Signed-off-by: Olof Johansson <olof@lixom.net>
following:
- Florian enables ARCH_BRCMSTB in the arm64 defconfig to get more build coverage
-----BEGIN PGP SIGNATURE-----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=EPCT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.13/defconfig-arm64' of http://github.com/Broadcom/stblinux into next/arm64
This pull request contains ARM64 defconfig changes for 4.13, please pull the
following:
- Florian enables ARCH_BRCMSTB in the arm64 defconfig to get more build coverage
* tag 'arm-soc/for-4.13/defconfig-arm64' of http://github.com/Broadcom/stblinux:
arm64: defconfig: Enable ARCH_BRCMSTB
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enable the SPI Communications Controller driver as module for the
Amlogic platform.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch enables the MEDIA Infrared RC Decoders and Meson Infrared
decoder for ARM64 defconfig.
These drivers are selected as modules by default.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: make RC_CORE modular too]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
ARCH_BRCMSTB was one of the few platforms that were not enabled by
default, since we are now adding more and more drivers relevant to that
platform get some proper build coverage.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
ARCH_VULCAN (Broadcom Vulcan) has been discontinued and all its
dependencies have been moved to ARCH_THUNDER2. It can be dropped
from defconfig now.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable some very core config options used on 64bit Rockchip socs.
As built-in driver enable the Rockchip spi driver as well as the
cros-ec-spi and cros-ec keyboard driver, as this may be helpful
in case an initrd does not work as expected and drops the user
into a shell. Another built-in is the fan53555 regulator driver,
as it and its register-compatible cousins Silergy syr827 and syr828
are often used on Rockchip socs as cpu-supply next to regular pmic.
The rest can be enabled as modules and contains the pcie host
controller and its phy, the sucessive approximation adc (saradc)
that gets often used for additional buttons on Rockchip boards
as well as the adc-keys Keyboard driver for these keys.
The cros-ec-pwm also can be a module, as it is normally only used to
drive display backlights as well as the Rockchip thermal controller
that allows to read the cpu and gpu temperatures and affect frequency
scaling if necessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable Qualcomm drivers needed to boot Dragonboard 410c with HDMI. This
enables support for clocks, regulators, and USB PHY.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
[Olof: Turned off _RPM configs per follow-up email]
Signed-off-by: Olof Johansson <olof@lixom.net>
Sync the defconfig with savedefconfig as config options change/move over
time.
Generated with the following commands:
make defconfig
make savedefconfig
cp defconfig arch/arm64/configs/defconfig
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Changes to platform code for 64-bit ARM platforms.
Most of these are small changes to the one defconfig we use on arm64
(no per-platform configs there), to enable new drivers.
There are also a few other changes. Broadcom sold off their 'Vulcan'
design to Cavium, where it is now called ThunderX2. While we normally
don't rename stuff based on marketing's whims, it seemed appropriate to
bring in renames on a few things such as MAINTAINERS, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NJ8c
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Olof Johansson:
"Changes to platform code for 64-bit ARM platforms.
Most of these are small changes to the one defconfig we use on arm64
(no per-platform configs there), to enable new drivers.
There are also a few other changes. Broadcom sold off their 'Vulcan'
design to Cavium, where it is now called ThunderX2. While we normally
don't rename stuff based on marketing's whims, it seemed appropriate
to bring in renames on a few things such as MAINTAINERS, etc"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: sunxi: always enable reset controller
arm64: defconfig: enable the Safexcel crypto engine as a module
arm64: configs: enable SDHCI driver for Xenon
MAINTAINERS: Broadcom Vulcan is now Cavium ThunderX2
arm64: defconfig: add Allwinner USB PHY
arm64: defconfig: enable MVPP2
arm64: defconfig: Enable video, DRM and LPASS drivers for Exynos5433 and Exynos7
arm64: exynos: Enable Exynos PMU and PM domains drivers
arm64: only select PINCTRL for Allwinner platforms
arm64: set CONFIG_MMC_BCM2835=y in defconfig
arm64: defconfig: enable I2C_PXA
arm64: defconfig: enable MVNETA
ARM64: defconfig: enable the leds-pwm driver and default-on trigger
arm64: defconfig: Enable SH Mobile I2C controller
Select two new drivers for ARM64 mvebu SoCs:
- Xenon SDHCI controller on Armada 37xx and Armada 7K/8K
- Safexcel crypto engine on Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWO+j/yMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SnoAJ9r0d9MIBvq
3TWmgUDmImgaucJ5HACggm9+Jqh/GgXTBlxFnszhN9/BuCM=
=Le5K
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.12-2' of git://git.infradead.org/linux-mvebu into next/arm64
mvebu defconfig64 for 4.12 (part 2)
Select two new drivers for ARM64 mvebu SoCs:
- Xenon SDHCI controller on Armada 37xx and Armada 7K/8K
- Safexcel crypto engine on Armada 7K/8K
* tag 'mvebu-defconfig64-4.12-2' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable the Safexcel crypto engine as a module
arm64: configs: enable SDHCI driver for Xenon
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Exynos power management drivers support now ARMv8 SoC - Exynos5433 - so
select them in ARCH_EXYNOS.
2. Enable few Exynos drivers for supported ARMv8 SoCs.
-----BEGIN PGP SIGNATURE-----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=lXKo
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc64-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/arm64
Samsung ARM64 update for v4.12:
1. Exynos power management drivers support now ARMv8 SoC - Exynos5433 - so
select them in ARCH_EXYNOS.
2. Enable few Exynos drivers for supported ARMv8 SoCs.
* tag 'samsung-soc64-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: defconfig: Enable video, DRM and LPASS drivers for Exynos5433 and Exynos7
arm64: exynos: Enable Exynos PMU and PM domains drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
Two patches to change our Kconfig option and add new options in the
defconfig.
-----BEGIN PGP SIGNATURE-----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=twCP
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/arm64
Allwinner arm64 config changes for 4.12
Two patches to change our Kconfig option and add new options in the
defconfig.
* tag 'sunxi-config64-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: add Allwinner USB PHY
arm64: only select PINCTRL for Allwinner platforms
Signed-off-by: Olof Johansson <olof@lixom.net>
The Safexcel EIP197 cryptographic engine is used on some Marvell SoCs,
such as Armada 7040 and Armada 8040. Enable this driver as a module in
the ARM64 defconfig.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables the driver for the SDHCI controller found on the
Marvell Armada 3700 and 7K/8K ARM64 SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Kdump is enabled by default as kexec is.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
4.12, please pull the following:
- Gerd enables the BCM2835 MMC driver which yields better performance than the
default one (iProc)
-----BEGIN PGP SIGNATURE-----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=KRAt
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/defconfig-arm64' of http://github.com/Broadcom/stblinux into next/arm64
Pull "Broadcom defconfig-arm64 changes for 4.12" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs defconfig updates for
4.12, please pull the following:
- Gerd enables the BCM2835 MMC driver which yields better performance than the
default one (iProc)
* tag 'arm-soc/for-4.12/defconfig-arm64' of http://github.com/Broadcom/stblinux:
arm64: set CONFIG_MMC_BCM2835=y in defconfig
Update arm64 defconfig by adding MVPP2 for Marvell Armada 7K/8K and
MVNETA and I2C_PXA for Armada 37xx.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWNVU1SMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71fVYAJ9Yp1KsFB7n
e2/64YGab3J5nQMFKwCeNQFTo4tZeU1Bnew1V83xfFpLXPQ=
=pCdd
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.12-1' of git://git.infradead.org/linux-mvebu into next/arm64
Pull "mvebu defconfig64 for 4.12 (part 1)" from Gregory CLEMENT:
Update arm64 defconfig by adding MVPP2 for Marvell Armada 7K/8K and
MVNETA and I2C_PXA for Armada 37xx.
* tag 'mvebu-defconfig64-4.12-1' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable MVPP2
arm64: defconfig: enable I2C_PXA
arm64: defconfig: enable MVNETA
The arm64 defconfig covers the Allwinner A64 SoC boards quite well,
but USB support is not enabled.
Add the PHY config symbol to allow defconfig kernels to use USB.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MVPP2 network driver is used for the ARM64 Marvell Armada 7K and 8K
platforms, so enable it in the arm64 defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable drivers specific to Exynos5433 and Exynos7:
1. MFD Low Power Audio SubSystem (LPASS),
2. DRM drivers (DECON display, outputs),
3. Drivers for video-related sub-blocks (JPEG, Multi Format Codec,
GScaler).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
We need to enable this controller so that we can switch the SD card's
pinmux over to it by default, which will improve storage performance.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Now that the Armada 37xx SoCs support the mvneta driver, enable it by
default. It is especially useful when booting on an NFS root.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This enables the leds-pwm driver to support LEDs which are PWM-powered
(and thus dimmable). Additionally we have to enable the "default-on"
trigger - this was not required before because the gpio-leds driver has
a separate "default-state" property which can be used to enable the LED
by default.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable SH Mobile I2C controller for use on R-Car Gen3 SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver
has been merged into mainline.
There is now a new defconfig file for tango4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWK8G/GCrR//JCVInAQLA3w/9GoJ+BvdlrieCdKj5ax9sDVMi11u5yDJP
NtoGM4RZlTFNr7bau8lbmJepH7K0ZLOWKfVisdvp3ykUszDkqqfRbOm7cmG8rQM7
K1BDDb0Mo0O6UgYAlgBM+zdhPEYZxSLYwSb9bAN4HlEkvuFsCwVURIN057IXP6zV
Hmb+a1nBmQAeXeVpxlBYQBV5HBXtbzNGUgXHAdBE6pO6uBC/8iNpzwaopP80eBr0
WXpqOe1ehW33ICeYKJPB13YwdfHNVnNuhMNTWGcCgBfXKBcSxWW72WsmmkO4sGFC
JtKz5revh1KySCyGmmi/sFKB0FIJkHF1VERQlmGRlh/6RBrLL5rqgXHr2HMgtbTy
rlFPPNWwl6DQl3xVg8UYg7Tz+k1HpHznUWaU4ng3MO8daHWnVEb06/TbO4SlDq+o
DEieUJDDTdAV01jGLuAU3AVOdBZKBY44NPp0d5EunzwaDPRY381XrECvlxxTuxq8
wxTTBYhL7rpt51d5ru59qwTqY6P0CiF4SeWNEth9Oh0Uyp0Vdj4Stkf4V6g647An
3jZg4NtKuFljzYVXkNH1//DTMNnCSUyaKbcbLzhV0D2aD5Pf2o2911tbu9Q/oEJT
PhISwCxsZ1tNccslmNGTr/G2hNihJqV7FNOrkfIEjddRzGhL1ot13BtUiEIZdA9Z
8F8BBga2ifI=
=noKQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
Changes to platform code for 64-bit ARM platforms, only trivial
stuff this time, a few defconfig changes to enable drivers, and
a new entry for the Cavium ThunderX2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ymi+
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms, only trivial stuff
this time, a few defconfig changes to enable drivers, and a new entry
for the Cavium ThunderX2 platform"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add Cavium ThunderX2 entry
arm64: add ARCH_THUNDER2 to defconfig
arm64: add THUNDER2 processor family
MAINTAINERS: Extend ARM/Mediatek SoC support section
arm64: defconfig: enable CONFIG_MMC_SDHCI_CADENCE
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
The PMULL based CRC32 implementation already contains code based on the
separate, optional CRC32 instructions to fallback to when operating on
small quantities of data. We can expose these routines directly on systems
that lack the 64x64 PMULL instructions but do implement the CRC32 ones,
which makes the driver that is based solely on those CRC32 instructions
redundant. So remove it.
Note that this aligns arm64 with ARM, whose accelerated CRC32 driver
also combines the CRC32 extension based and the PMULL based versions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This will allow the default kernel build to boot on Cavium ThunderX2
CN99XX processors.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the NAND framework and the Denali NAND controller driver.
This NAND controller is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the block layer support for MTD devices.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the Cadence SD/SDIO/eMMC controller. This is used on
Socionext UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since much more arm64 SoCs with numa nodes, it's better to enable
NUMA and NUMA_BALANCING to improve the performance on test.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Update arm64 defconfig by adding XORv2 for Marvell Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWHkE/iMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71XkoAJ9NBtmwvDxp
Rqi2aEq7ki6oU/jybwCdG0CYDLRyzoR4HKVy0mVtgnsMnLw=
=lET3
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.11-1' of git://git.infradead.org/linux-mvebu into next/arm64
mvebu defconfig64 for 4.11 (part 1)
Update arm64 defconfig by adding XORv2 for Marvell Armada 7K/8K
* tag 'mvebu-defconfig64-4.11-1' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit enables the XORv2 DMA driver, which is used on the ARM64
Marvell Armada 7K and 8K platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should
now work much better with the default build.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B+Lz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms. We are not adding
any new platforms that require code or Kconfig changes this time, so
it's basically just defconfig changes to enable support for more
drivers used on the existing platforms.
This is mainly interesting for the Raspberry Pi 3, which should now
work much better with the default build"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: drop GPIO_SYSFS on multiplatforms
arm64: defconfig: Do not lower CONFIG_LOG_BUF_SHIFT
arm64: defconfig: allow rk3399-based boards to boot from mmc and usb
arm64: defconfig: enable RK808 components
arm64: defconfig: enable I2C and DW MMC controller on rockchip platform
arm64: defconfig: Enable Tegra186 SoC
ARM64: configs: Activate Internal PHY for Meson GXL
arm64: qcom: enable GPIOLIB in Kconfig
arm64: configs: enable configs for msm899(2/4) basic support
ARM64: bcm2835: add thermal driver to default config
ARM64: configs: Add Platform MHU in defconfig
MAINTAINERS: Update Broadcom Vulcan maintainer email
arm64: defconfig: enable EEPROM_AT25 config option
arm64: Enable HIBERNATION in defconfig
arm64: defconfig: Enable DRM DU and V4L2 FCP + VSP modules
ARM64: defconfig: Enable MMC related configs
arm64: Add BCM2835 (Raspberry Pi 3) support to the defconfig
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- Uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- Support for systems without FP/SIMD (IOW, kernel avoids touching these
registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- Handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- Use of the page table contiguous hint for kernel mappings
- Hugetlb fixes for sizes involving the contiguous hint
- Remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- Boot-time checks for writable+executable kernel mappings
- Simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Uk9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- support for systems without FP/SIMD (IOW, kernel avoids touching
these registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- use of the page table contiguous hint for kernel mappings
- hugetlb fixes for sizes involving the contiguous hint
- remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- boot-time checks for writable+executable kernel mappings
- simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (60 commits)
arm64: Disable PAN on uaccess_enable()
arm64: Work around broken .inst when defective gas is detected
arm64: Add detection code for broken .inst support in binutils
arm64: Remove reference to asm/opcodes.h
arm64: Get rid of asm/opcodes.h
arm64: smp: Prevent raw_smp_processor_id() recursion
arm64: head.S: Fix CNTHCTL_EL2 access on VHE system
arm64: Remove I-cache invalidation from flush_cache_range()
arm64: Enable HIBERNATION in defconfig
arm64: Enable CONFIG_ARM64_SW_TTBR0_PAN
arm64: xen: Enable user access before a privcmd hvc call
arm64: Handle faults caused by inadvertent user access with PAN enabled
arm64: Disable TTBR0_EL1 during normal kernel execution
arm64: Introduce uaccess_{disable,enable} functionality based on TTBR0_EL1
arm64: Factor out TTBR0_EL1 post-update workaround into a specific asm macro
arm64: Factor out PAN enabling/disabling into separate uaccess_* macros
arm64: Update the synchronous external abort fault description
selftests: arm64: add test for unaligned/inexact watchpoint handling
arm64: Allow hw watchpoint of length 3,5,6 and 7
arm64: hw_breakpoint: Handle inexact watchpoint addresses
...
to basically boot.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYNvxvEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYH13Af9
GN3Rx9JrPOKxmp8yQrjf2IvtbRCNcyJsYAcT2C33KFrT+jZE087i+BdMZ9cniwr/
Y3w2JLyi6DS2aeoEZnYDsSQiBNudKKOeyDih5uI+oFDPQfmmfPfjuJUW5NrnpHSd
SLmXADAwjkB46o7Z1gFwquhXB+LcxjsYE5eu7Eda4pSHuBw2ZtNMMrZNDujJx/vU
zu36utDBWYFx6yMx32U1TYz3pf9cbi784j/Y5wr1zSCmuOgS2AZpl8KFC//92ZtU
Wi8T3sRBupun99/pVj+xvWtB9aHdWr8QxeVkRIUhx5XpM7njy9rX7QcJIDMm4kBf
uSbKZCh/uAjRjT/TpQiOsw==
=Fv2o
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-defconfig64' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/arm64
Pull "Rockchip defconfig64 changes for 4.10" from Heiko Stübner:
64bit defconfig changes to allow arm64 Rockchip socs
to basically boot.
* tag 'v4.10-rockchip-defconfig64' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: defconfig: allow rk3399-based boards to boot from mmc and usb
arm64: defconfig: enable RK808 components
arm64: defconfig: enable I2C and DW MMC controller on rockchip platform
The sysfs ABI to GPIO is marked obsolete and should not be
encouraged. Users should be encouraged to switch to using the
character device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
please pull the following changes:
- Eric updates the ARMv8 defconfig to contain everything that is needed to run
a 64-bit kernel on the Raspberry Pi 3
- Scott enables the standard AT25 EEPROM driver as module for the ARM64 defconfig
- Martin enables the Raspberry Pi Thermal driver in the ARM64 defconfig
-----BEGIN PGP SIGNATURE-----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=mWnY
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/defconfig-arm64' of http://github.com/Broadcom/stblinux into next/arm64
Pull "Broadcom defconfig-arm64 changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs defconfig changes for 4.10,
please pull the following changes:
- Eric updates the ARMv8 defconfig to contain everything that is needed to run
a 64-bit kernel on the Raspberry Pi 3
- Scott enables the standard AT25 EEPROM driver as module for the ARM64 defconfig
- Martin enables the Raspberry Pi Thermal driver in the ARM64 defconfig
* tag 'arm-soc/for-4.10/defconfig-arm64' of http://github.com/Broadcom/stblinux:
ARM64: bcm2835: add thermal driver to default config
arm64: defconfig: enable EEPROM_AT25 config option
arm64: Add BCM2835 (Raspberry Pi 3) support to the defconfig
The default value of 17 for CONFIG_LOG_BUF_SHIFT is much more suitable
than 14. The latter easily leads to lost kernel messages on systems with
only one CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Enable additional options necessary to boot rk3399-based boards to
boot from either emmc or usb devices, like the arasan sdhci and its phy
as well as the usb2 phy and general rockchip power-domain support.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Many rockchip based arm64 boards use RK808 as PMIC, so
enabe it here let the board bootup normally.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[added rk808-rtc as module and rk808-clk output built in]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C and MMC are very basic modules for a board to bootup, as I2C always
used to configure PMIC and MMC devices often used to store filesytem.
So enable them here to let the rockchip based arm64 boards can bootup.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Given the mimimal hardware support for msm899(2/4) currently.
A few config options are needed to allow for continued
development and booting.
The following are needed for continued development and
booting:
-8994 pinctrl for serial support
-Enable Global Glock Controller (gcc)
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the thermal driver for bcm2837 to list of compiled modules
in the default config.
Changelog:
V7 -> V8: rebased
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* Enable R-Car DU and related drivers as modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ztt2
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/arm64
Renesas ARM64 Based SoC Defconfig Updates for v4.10
* Enable R-Car DU and related drivers as modules in defconfig
* tag 'renesas-arm64-defconfig-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: Enable DRM DU and V4L2 FCP + VSP modules
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable support for on board SPI EEPROM by setting
CONFIG_EEPROM_AT25=m
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds CONFIG_HIBERNATION to the arm64 defconfig.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Extend the ARM64 defconfig to enable the DU DRM device as module
together with required dependencies of V4L2 FCP and VSP modules.
This enables VGA output on the r8a7795 Salvator-X board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable MMC related defaults configs for MMC, PWM and PWM clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Most of the drivers are included as modules, except for serial (needed
for early console), WDT (required for reboot), and the dependency
chain of RASPBERRYPI_POWER (which is currently not buildable as a
module, but should be changed).
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable CONFIG_GPIO_XGENE_SB.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Enable ZTE ZX family support in arm64 defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX25FiAAoJEFBXWFqHsHzOzJ4IAKAxI7W3Ubnhdxdu8akLYm6a
VHtnqSyr43kKCUEbg05+oTmPzXVF7YdnYmZpyy2mhA9+wpGC6vSwtSDM6Tj8KN8H
ZGzR5Op94GPN3RnLRyGlplltMEbH4I8l6A7SsiJ5VB4Uab2x4bmBagW/vG0O+XuP
exzGQoqlrI5N2gmiSf6P+2Y1oEM+JvClvWPdb9zkMb0B4i8kNJgh+efyNaCv7m/R
v0s9f9AhhK3Saj2TSaJuGuZNHw9vZpDUiOuyTOvnc35bJLjy0AsWqw4BfK8NegQE
4tgXiyVdZxOHvUtAQgw7b2Wkcxo+407zDJE1q6HxR2uudpuTHm0hyWxN62MuXm8=
=zgWs
-----END PGP SIGNATURE-----
Merge tag 'zte-defconfig64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/arm64
Pull "ZTE arm64 defconfig updates for 4.9" from Shawn Guo:
- Enable ZTE ZX family support in arm64 defconfig
* tag 'zte-defconfig64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: enable ZTE ZX related config
Enable common modules for power management; one is to enable
CPUFREQ_DT driver; the driver is used by many platforms by passing OPP
table from device tree.
Also enables thermal related drivers. Firstly we need enable
configuration CPU_THERMAL for CPU cooling device driver, this will bind
thermal zone with CPU cooling device; and enable 'power allocator'
thermal governor.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add PCIe driver for Aardvark for Armada 3700
- enable xhci-platform for A7K/A8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfMQewACgkQCwYYjhRyO9WrKgCeJWuHOFUlMYoZqEYKkdA5aJ9G
iPsAoIFQivT7yCn9p7rJKzKt2NI4skoy
=jIwM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.9-1' of git://git.infradead.org/linux-mvebu into next/arm64
Pull "mvebu defconfig64 for 4.9 (part 1)" from Gregory CLEMENT:
- add PCIe driver for Aardvark for Armada 3700
- enable xhci-platform for A7K/A8K
* tag 'mvebu-defconfig64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: configs: enable PCIe driver for Aardvark
arm64: defconfig: enable xhci-platform
drivers/char/hw_random/Kconfig has 'default m', so
simply removing this entry from the defconfig will
enable building HW random drivers as modules.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable hisilicon SAS and XGE for hip05 and hip06
- Enable drm, powerkey, bluetooth and adv7511/adv7533 for hikey
- Add PINCTRL to HISI platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y80h
-----END PGP SIGNATURE-----
Merge tag 'hisi-defconfig-for-4.9' of git://github.com/hisilicon/linux-hisi into next/arm64
Pull "ARM64: hisilicon: defconfig updates for 4.9" from Wei Xu:
- Enable hisilicon SAS and XGE for hip05 and hip06
- Enable drm, powerkey, bluetooth and adv7511/adv7533 for hikey
- Add PINCTRL to HISI platform
* tag 'hisi-defconfig-for-4.9' of git://github.com/hisilicon/linux-hisi:
Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
arm64: defconfig: enable bluetooth supports as modules
arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
arm64: defconfig: Enable Hisi SAS and HNS
This allows use of the SDHI SD/SDIO controller present on R-Car Gen3 SoCs
and already enabled in the DT of the r8a7795/salvator-x (H3).
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables the driver for the PCIe host controller found on the
Marvell Armada 3700 ARM64 SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the following items for bluetooth mouse and speaker which base
on HCIUART.
a) CONFIG_BT_HCIUART
b) CONFIG_BT_HCIUART_LL
c) CONFIG_BT_HIDP
Enable bluetooth LED support.
d) CONFIG_BT_LEDS
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable HiSilicon kirin drm driver for HiKey: CONFIG_DRM_HISI_KIRIN
Enable adv7511/adv7533 for HiKey: CONFIG_DRM_I2C_ADV7511
Build these components as modules.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Now that ACPI is on in the defconfig, the time seems right to enable
drivers for the SD/MMC, DMA, and pin control hardware described in the ACPI
tables of the QDF2432 server platform.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When CONFIG_LOCALVERSION_AUTO is disabled, the version string is
just a tag name (or with a '+' appended if HEAD is not a tagged
commit).
During the development (and especially when git-bisecting), longer
version string would be helpful to identify the commit we are running.
This is a default y option, so drop the unset to enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable options commonly needed by popular virtualization
and container applications. Use modules when possible to
avoid too much overhead for users not interested.
- add namespace and cgroup options needed
- add seccomp - optional, but enhances Qemu etc
- bridge, nat, veth, macvtap and multicast for routing
guests and containers
- btfrs and overlayfs modules for container COW backends
- while near it, make fuse a module instead of built-in.
Generated with make saveconfig and dropping unrelated spurious
change hunks while commiting. bloat-o-meter old-vmlinux vmlinux:
add/remove: 905/390 grow/shrink: 767/229 up/down: 183513/-94861 (88652)
....
Total: Before=10515408, After=10604060, chg +0.84%
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some ARM64 platforms (for example the Marvell Armada 7K/8K) use the
generic XHCI platform driver, so it makes sense to enable
CONFIG_USB_XHCI_PLATFORM=y in the defconfig to support XHCI on such
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Changes to platform code for 64-bit ARM platforms.
Nearlt all of these are defconfig updates to enable new drivers or old
drivers still used on these 64-bit platforms.
Added platforms for this release are:
- Broadcom BCM2837
- Renesas R8A7796
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vsam
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull 64-bit ARM SoC updates from Olof Johansson:
"Changes to platform code for 64-bit ARM platforms.
Nearly all of these are defconfig updates to enable new drivers or old
drivers still used on these 64-bit platforms.
Added platforms for this release are:
- Broadcom BCM2837
- Renesas R8A7796"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: remove duplicate PWM entry in defconfig
arm64: Update default configuration
arm64: defconfig: Enable more IP blocks for Exynos7 and Exynos5433
arm64: amlogic: select gxbb clk driver
arm64: defconfig: Enable S2MPS11 clock and S3C RTC driver
arm64: marvell: enable Armada 3700 clock drivers
arm64: defconfig: enable msm8996 pinctrl support
arm64: defconfig: Enable qcom msm8996 clk drivers
arm: defconfig: Enable PM8941 pwr key
arm64: defconfig: enable stmmac and realtek PHY as modules
arm64: Kconfig: select PM{,_GENERIC_DOMAINS} for ARCH_VEXPRESS
arm64: defconfig: enable SENSORS_ARM_SCPI
arm64: defconfig: enable Generic on-chip SRAM driver
arm64: configs: enable PCIe driver for Armada 7K/8K
arm64: Add platform selection for BCM2835.
arm64: defconfig: disable plain NEON implementation of AES
arm64: Allow for different DMA and CPU bus offsets
arm64: defconfig: enable Renesas R8A7796 SoC
arm64: defconfig: Enable Cadence MACB/GEM support
ARM64: Kconfig: Select the Amlogic Meson pin controller driver
...
We merged two patches that both enabled CONFIG_PWM, leading to a harmless
warning:
arch/arm64/configs/defconfig:352:warning: override: reassigning to symbol PWM
This removes one of the two identical lines to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable a bunch of configuration options to enable PMIC, regulators, DSI,
HDMI, XUSB and the GPU on Jetson TX1 as well as a few new features that
are now functional on the Google Pixel C.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=483Z
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/arm64
Merge "arm64: tegra: Default configuration updates for v4.8-rc1" from Thierry Reding:
Enable a bunch of configuration options to enable PMIC, regulators, DSI,
HDMI, XUSB and the GPU on Jetson TX1 as well as a few new features that
are now functional on the Google Pixel C.
* tag 'tegra-for-4.8-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: Update default configuration
Enable a couple of drivers that are used on Jetson TX1:
* GPIO_PCA953X, GPIO_PCA953X_IRQ: Two instances of this I2C GPIO
expander are used on Jetson TX1 to expand the number of usable GPIOs
on the I/O board. Enable the driver for this expander along with IRQ
support.
* MFD_MAX77620, REGULATOR_MAX77620, PINCTRL_MAX77620, GPIO_MAX77620,
RTC_DRV_MAX77686: Enable support for the PMIC and various of its
components found on the Jetson TX1 processor module (p2180).
* RTC_DRV_TEGRA: This RTC is usually not hooked up to a battery on
boards, but it can be useful as a wakeup source from suspend to RAM.
* REGULATOR_PWM: The GPU is supplied by a regulator controlled via one
of the Tegra's PWM channels.
* DRM, DRM_NOUVEAU, DRM_TEGRA, DRM_PANEL_SIMPLE: Enable support for an
optional DSI panel on Jetson TX1 as well as the GPU.
* BACKLIGHT_GENERIC, BACKLIGHT_LP855X: The backlight on Jetson TX1, if
shipped with a display module, is driver by an LP8557.
* PHY_TEGRA_XUSB, USB_XHCI_TEGRA: Enable support for XUSB (USB 3.0) on
Jetson TX1.
* PWM, PWM_TEGRA: One of the PWM channels is used to control the
voltage supplied to the GPU.
* NFS_V4_1, NFS_V4_2: Support these newer versions of the NFS protocol
to increase compatibility with distributions.
* MFD_CROS_EC, MFD_CROS_EC_I2C and I2C_CROS_EC_TUNNEL: Used to enable
the ChromeOS Embedded Controller and the I2C tunnel that allows the
EC to function as an I2C bridge.
* BATTERY_BQ27XXX: Support the battery charger and monitor found on
the Google Pixel C.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable more drivers for IP blocks for existing Exynos7 and upcoming
Exynos5433:
1. SPI,
2. Watchdog,
3. USB: DWC3, Exynos EHCI and OHCI,
4. Exynos ADC,
5. Samsung PWM.
These are already used by Exynos7 Espresso board or will be used by
Exynos5433 based board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
The S3C RTC controller on Exynos7 platform uses RTC source clock
from S2MPS11 PMIC. This patch enables the required drivers to make
RTC work on Exynos7 Espresso board.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
1. Enable support for SCPI based sensors(temperature, voltage,
current and power)
2. Enable the Generic on-chip SRAM driver. SRAM is used for SCPI based
communication with SCP on Juno
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r5Ie
-----END PGP SIGNATURE-----
Merge tag 'juno-defconfig-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/arm64
ARMv8 Juno/Vexpress defconfig updates for v4.8
1. Enable support for SCPI based sensors(temperature, voltage,
current and power)
2. Enable the Generic on-chip SRAM driver. SRAM is used for SCPI based
communication with SCP on Juno
* tag 'juno-defconfig-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: defconfig: enable SENSORS_ARM_SCPI
arm64: defconfig: enable Generic on-chip SRAM driver
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable the PCIe host controller found on the Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAldpA7YACgkQCwYYjhRyO9UpFwCgoVM2L6jaF0AU9Yg+aR8xeHrF
5xUAnRCe8B0TYqE0Bucj+MwmKXbWTLU7
=sEoy
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.8-1' of git://git.infradead.org/linux-mvebu into next/arm64
mvebu defconfig64 for 4.8 (part 1)
- Enable the PCIe host controller found on the Armada 7K/8K SoCs
* tag 'mvebu-defconfig64-4.8-1' of git://git.infradead.org/linux-mvebu:
arm64: configs: enable PCIe driver for Armada 7K/8K
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables pinctrl support required to boot msm8996/apq8096
boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the clk drivers on msm8996. This allows us to boot and
test most device drivers on this SoC.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Some Amlogic GXBB boards use the stmmac ethernet driver. Also, enable
the realtek PHY used on meson-gxbb-odroidc2. The micrel PHY used on the
meson-gxbb-p20x boards is already enabled.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
ARM SCPI Sensors were merged for v4.4 and they are defined in the Juno
dts. Enable it in the defconfig to get them registered automatically in
Juno by default.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Most of the ARM SoCs have small SRAM memory used for various purposes
that require faster access to data compared to normal DDR.
This patch enables the Generic on-chip SRAM driver on ARM64.
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch enables the driver for the PCIe host controller found on
the Marvell Armada 7K/8K ARM64 SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The plain NEON implementation of AES is only suited for v8 cores that lack
the ARMv8 Crypto Extensions but have an implementation of the NEON tbl/tbx
instruction that is not pathetically slow. Unfortunately, this is currently
the empty set, so there is no point in including this implementation by
default. So disable it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables the Renesas R8A7796 SoC in the arm64 defconfig.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch enables the cadence MACB/GEM support that is needed
by lg1k SoCs.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull watchdog updates from Wim Van Sebroeck:
- add support for Fintek F81865 Super-IO chip
- add support for watchdogs (RWDT and SWDT) found on RCar Gen3 based
SoCs from Renesas
- octeon: Handle the FROZEN hot plug notifier actions
- f71808e_wdt fixes and cleanups
- some small improvements in code and documentation
* git://www.linux-watchdog.org/linux-watchdog:
MAINTAINERS: Add file patterns for watchdog device tree bindings
Documentation: Add ebc-c384_wdt watchdog-parameters.txt entry
watchdog: shwdt: Use setup_timer()
watchdog: cpwd: Use setup_timer()
arm64: defconfig: enable Renesas Watchdog Timer
watchdog: renesas-wdt: add driver
watchdog: remove error message when unable to allocate watchdog device
watchdog: f71808e_wdt: Fix WDTMOUT_STS register read
watchdog: f71808e_wdt: Fix typo
watchdog: f71808e_wdt: Add F81865 support
watchdog: sp5100_tco: properly check for new register layouts
watchdog: core: Fix circular locking dependency
watchdog: core: fix trivial typo in a comment
watchdog: hpwdt: Adjust documentation to match latest kernel module parameters.
watchdog: imx2_wdt: add external reset support via dt prop
watchdog: octeon: Handle the FROZEN hot plug notifier actions.
watchdog: qcom: Report reboot reason
As usual, a bunch of commits, mostly adding drivers and other options to
defconfigs.
We are adding three new defconfig files for the newly added 32-bit
machines (aspeed and mps2), the rest is mainly housekeeping.
The changes outside of arch/arm/config/ are for a Kconfig symbol
that got renamed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ecJp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs.
We are adding three new defconfig files for the newly added 32-bit
machines (aspeed and mps2), the rest is mainly housekeeping.
The changes outside of arch/arm/config/ are for a Kconfig symbol that
got renamed"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (63 commits)
ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME
ARM: u8500_defconfig: update sensor config
ARM: u8500_defconfig: remove staging from defconfig
ARM: multi_v7_defconfig: Remove unused Kconfig option MACH_UX500_DT
ARM: at91/defconfig: sama5: add CONFIG_FHANDLE
arm/configs: Add Aspeed defconfig
arm/configs/multi_v5: Add Aspeed ast2400
ARM: at91: sama5: Update defconfig
ARM: imx_v6_v7_defconfig: add CONFIG_MICREL_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_I2C_GPIO
ARM: multi_v7: Enable Tegra XUSB controller in defconfig
ARM: tegra: Enable XUSB controller in defconfig
ARM: omap2plus_defconfig: Enable PWM and ir-rx51 as loadable modules
ARM: multi_v7_defconfig: add the Atmel sama5d2-compatible ADC driver
ARM: multi_v7_defconfig: add the Atmel Audio microphone interface PDMIC
ARM: multi_v7_defconfig: add Atmel ISI (Image Sensor Interface) driver
ARM: multi_v7_defconfig: add Atmel watchdog timers
ARM: multi_v7_defconfig: add HLCDC drivers as modules
ARM: at91/defconfig: add PDMIC driver to sama5_defconfig
ARM: at91/defconfig: add HLCDC driver to sama5_defconfig
...
One new platform gets added this time: The Cortex-A53 based LG Electronics
LG1K platform used in digital TVs.
The other changes are mostly smaller updates to the defconfig files, to
enable additional platform specific drivers, as they get merged through
the subsystem trees.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ISkf
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Arnd Bergmann:
"One new platform gets added this time: The Cortex-A53 based LG
Electronics LG1K platform used in digital TVs.
The other changes are mostly smaller updates to the defconfig files,
to enable additional platform specific drivers, as they get merged
through the subsystem trees"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: configs: add options useful for Armada 7K/8K support
arm64: defconfig: Add Juno SATA controller
arm64: defconfig: enable freescale/nxp config options
arm64: defconfig: enable 48-bit virtual addresses
arm64: defconfig: cleanup the defconfig
MAINTAINERS: update entry for Marvell ARM platform maintainers
arm64: marvell: enable AP806 and CP110 syscon driver
arm64: Kconfig: select sp804 timer for ARCH_HISI
arm64: defconfig: enable configs for WLAN and TI WL1835 as modules
arm64: defconfig: enable several common USB network adapters
arm64: defconfig: add CONFIG_SPI_SPIDEV as module
arm64: defconfig: Enable the PMIC and regulator for Hi6220 and 96boards HiKey
arm64: defconfig: Add Renesas R-Car USB 3.0 driver support
MAINTAINERS: add Chanho Min as ARM/LG1K maintainer
arm64: defconfig: enable ARCH_LG1K
arm64: add Kconfig entry for LG1K SoC family
arm64: defconfig: Enable PL330 DMA controller
arm64: defconfig: enable basic boot for Amlogic meson
- update arm64 defconfig with options useful for Armada 7K/8K support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlcx85oACgkQCwYYjhRyO9VvdACfZUGxgpLlq3bpu0TymeLZfbfn
4qYAmwT6iwH3Vnu/mYeXRUP81EsBUNyk
=hgwZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.7-1' of git://git.infradead.org/linux-mvebu into next/arm64
Merge "mvebu defconfig for arm64 for 4.7" from Gregory CLEMENT:
- update arm64 defconfig with options useful for Armada 7K/8K support
* tag 'mvebu-defconfig64-4.7-1' of git://git.infradead.org/linux-mvebu:
arm64: configs: add options useful for Armada 7K/8K support
This commit updates the ARM64 defconfig to include additional options
useful to support the Armada 7K/8K platforms:
- the SPI controller driver, spi-orion
- the support for SPI flashes
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The ARM Juno (r1 and r2) boards feature a SATA controller soldered
on the board and connected to the PCI bus.
Add the respective driver to defconfig to get hard disks supported out
of the box on the Junos.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Clean up defconfig with savedefconfig
- Enable 48-bit virtual address support
- Enable driver support for various Freescale/NXP devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKL+fAAoJEFBXWFqHsHzOLcIH/26qqItBXLZ8k/wMVjvRTpud
7jmZbZTBtl9p+q3CnMyOSoBSWK7ov45SQBDYH0PCNiYgMlRIGA0vli8WGBt/BGo5
NS0p81aCPf7QmE1t4A3HPiteTY4iJOkFwiguC+UOwXlmJ3CmK+07MqaTiUDW+fHV
EVftBG+LHF555JO4vxXXVqF+jHM89ZzLI2G3jjIbn9qjPdmzEF/WYd+H8qVnLTwv
geZ7C9/E3KqsRS1xyBdkK0TbjNPGadu0HrbyRaOTXICD27DxiwipOPa7ScriVYrd
+1mvG85Zwn8lVi4Vrl4A9FSwYSEcDzLqr2vG8Wnbffn0OtpLvp/f+60EOAaK2uM=
=CiZ+
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig64-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/arm64
Merge "The arm64 defconfig update for Freescale/NXP support" from Shawn Guo:
- Clean up defconfig with savedefconfig
- Enable 48-bit virtual address support
- Enable driver support for various Freescale/NXP devices
* tag 'imx-defconfig64-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: enable freescale/nxp config options
arm64: defconfig: enable 48-bit virtual addresses
arm64: defconfig: cleanup the defconfig
* Add Renesas R-Car USB 3.0 driver support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MGPx
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/arm64
Merge "Renesas ARM64 Based SoC Defconfig Updates for v4.7" from Simon Horman:
* Add Renesas R-Car USB 3.0 driver support
* tag 'renesas-arm64-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: Add Renesas R-Car USB 3.0 driver support
Some armv8 SoCs (e.g. ls2080a) have physical memory maps with discontiguous
DDR regions that require 48-bit VA to have the linear map cover the entire
range of DDR.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When doing:
make defconfig
make savedefconfig
...without making any changes, the newly saved defconfig does
not match arch/arm64/configs/defconfig, and the diff looks
like:
$ diff defconfig arch/arm64/configs/defconfig
3a4
> CONFIG_FHANDLE=y
Clean that up by committing the output of savedefconfig.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable ACPI by default to support testing of ACPI only systems and
ensure that defconfig will boot on anything, for arm64 this is not done
in Kconfig since a very large proportion of arm64 systems have no ACPI
at all.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Roy Franz <roy.franz@hpe.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HTRw
-----END PGP SIGNATURE-----
Merge tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Renesas ARM Based SoC Pci Defconfig Updates for v4.7" from Simon Horman:
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
* tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PCI: rcar-pcie: Remove Gen2 designation from Kconfig
- Enable Hi655x PMIC and regulator
- Enable SPI_SPIDEV as module
- Enable several common USB-Ethernet dongles
- Enable configs for WLAN and TI WL1835 as modules
- Enable ARM SP804 for ARCH_HISI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1Jq
-----END PGP SIGNATURE-----
Merge tag 'hi6220-config-for-4.7v3' of git://github.com/hisilicon/linux-hisi into next/arm64
Merge "ARM64: Hi6220: configure updates for 4.7 based on rc3" from Wei Xu:
- Enable Hi655x PMIC and regulator
- Enable SPI_SPIDEV as module
- Enable several common USB-Ethernet dongles
- Enable configs for WLAN and TI WL1835 as modules
- Enable ARM SP804 for ARCH_HISI
* tag 'hi6220-config-for-4.7v3' of git://github.com/hisilicon/linux-hisi:
arm64: Kconfig: select sp804 timer for ARCH_HISI
arm64: defconfig: enable configs for WLAN and TI WL1835 as modules
arm64: defconfig: enable several common USB network adapters
arm64: defconfig: add CONFIG_SPI_SPIDEV as module
arm64: defconfig: Enable the PMIC and regulator for Hi6220 and 96boards HiKey
This patch enables TI WL1835 and builds as module. It also enables
CFG80211, MAC80211, RFKILL and several CRYPTOs which are required
by WLAN.
96boards HiKey uses TI WLAN/BT combo module WL1835MOD.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The arm64 system is likely to be used as a host computer instead of
embedded devices and adding USB-Ethernet dongles to make it behave as
host PC is mandatory.
Changelog:
v2: Changed drivers to be as modules instead of built-in.
Signed-off-by: Akira Tsukamoto <akira.tsukamoto@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
