Add a function that waits for the last command to complete and checks
the status, and use it where appropriate. This prepares for the subsequent
fix of the completion condition in rmi_f34_attention(), which would
previously lead to a timeout instead of a more detailed error message
whenever a command was unsuccessful with v7/v8 bootloaders.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20220608124808.51402-3-matthias.schiffer@ew.tq-group.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit a6977d758f ("Input: synaptics-rmi4 - support bootloader v8 in
f34v7") allowed the F34v7 driver to probe with bootloader v8, but it did
not update various other bootloader version checks in the F34 code.
Fixes: a6977d758f ("Input: synaptics-rmi4 - support bootloader v8 in f34v7")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20220608124808.51402-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220818210022.6865-1-wsa+renesas@sang-engineering.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- a new driver for Azoteq IQS7222A/B/C capacitive touch controller
- a new driver for Raspberry Pi Sense HAT joystick
- sun4i-lradc-keys gained support of R329 and D1 variants, plus it
can be now used as a wakeup source
- pm8941-pwrkey can now properly handle PON GEN3 variants; the driver
also implements software debouncing and has a workaround for missing
key press events
- assorted driver fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCYpGmGgAKCRBAj56VGEWX
nI/4AP4v7b+G1MIDKogUODqCMKatZmOaxoa5fFNs2QFBq9+pVgEAlCnGhcdvhrlT
/lJZwxAmGhwm7dZ+0edfjyD3C+R8Zg0=
=sVNU
-----END PGP SIGNATURE-----
Merge tag 'input-for-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for the Azoteq IQS7222A/B/C capacitive touch controller
- a new driver for Raspberry Pi Sense HAT joystick
- sun4i-lradc-keys gained support of R329 and D1 variants, plus it can
be now used as a wakeup source
- pm8941-pwrkey can now properly handle PON GEN3 variants; the driver
also implements software debouncing and has a workaround for missing
key press events
- assorted driver fixes and cleanups
* tag 'input-for-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: stmfts - do not leave device disabled in stmfts_input_open
Input: gpio-keys - cancel delayed work only in case of GPIO
Input: cypress_ps2 - fix typo in comment
Input: vmmouse - disable vmmouse before entering suspend mode
dt-bindings: google,cros-ec-keyb: Fixup bad compatible match
Input: cros-ec-keyb - allow skipping keyboard registration
dt-bindings: google,cros-ec-keyb: Introduce switches only compatible
Input: psmouse-smbus - avoid flush_scheduled_work() usage
Input: bcm-keypad - remove unneeded NULL check before clk_disable_unprepare
Input: sparcspkr - fix refcount leak in bbc_beep_probe
Input: sun4i-lradc-keys - add support for R329 and D1
Input: sun4i-lradc-keys - add optional clock/reset support
dt-bindings: input: sun4i-lradc-keys: Add R329 and D1 compatibles
Input: sun4i-lradc-keys - add wakeup support
Input: pm8941-pwrkey - simulate missed key press events
Input: pm8941-pwrkey - add software key press debouncing support
Input: pm8941-pwrkey - add support for PON GEN3 base addresses
Input: pm8941-pwrkey - fix error message
Input: synaptics-rmi4 - remove unnecessary flush_workqueue()
Input: ep93xx_keypad - use devm_platform_ioremap_resource() helper
...
All work currently pending will be done first by calling destroy_workqueue,
so there is unnecessary to flush it explicitly.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ran jianping <ran.jianping@zte.com.cn>
Link: https://lore.kernel.org/r/20220422093304.2781183-1-ran.jianping@zte.com.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
media Kconfig has two entries associated to V4L API:
VIDEO_DEV and VIDEO_V4L2.
On Kernel 2.6.x, there were two V4L APIs, each one with its own flag.
VIDEO_DEV were meant to:
1) enable Video4Linux and make its Kconfig options to appear;
2) it makes the Kernel build the V4L core.
while VIDEO_V4L2 where used to distinguish between drivers that
implement the newer API and drivers that implemented the former one.
With time, such meaning changed, specially after the removal of
all V4L version 1 drivers.
At the current implementation, VIDEO_DEV only does (1): it enables
the media options related to V4L, that now has:
menu "Video4Linux options"
visible if VIDEO_DEV
source "drivers/media/v4l2-core/Kconfig"
endmenu
but it doesn't affect anymore the V4L core drivers.
The rationale is that the V4L2 core has a "soft" dependency
at the I2C bus, and now requires to select a number of other
Kconfig options:
config VIDEO_V4L2
tristate
depends on (I2C || I2C=n) && VIDEO_DEV
select RATIONAL
select VIDEOBUF2_V4L2 if VIDEOBUF2_CORE
default (I2C || I2C=n) && VIDEO_DEV
In the past, merging them would be tricky, but it seems that it is now
possible to merge those symbols, in order to simplify V4L dependencies.
Let's keep VIDEO_DEV, as this one is used on some make *defconfig
configurations.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for meson-vdec & meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.
Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200227130336.27042-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the kerneldoc warnings from building the driver with W=1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-2-lee.jones@linaro.org
[dtor: folded together several Lee's patches; added more descriptions]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the recent addition of the F3A support, we can now accept
bootloader v8, which will help support recent Thinkpads.
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20200930225046.173190-2-Jason@zx2c4.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
RMI4 F3A supports the touchpad GPIO function, it's designed to
support more GPIOs and used on newer touchpads. This patch adds
support of the touchpad buttons.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200930094147.635556-3-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
f30_data in rmi_device_platform_data could be also referenced by RMI
function 3A, so rename it and the structure name to avoid confusion.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200930094147.635556-2-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix a use-after-free noticed by running with KASAN enabled. If
rmi_irq_fn() is run twice in a row, then rmi_f11_attention() (among
others) will end up reading from drvdata->attn_data.data, which was
freed and left dangling in rmi_irq_fn().
Commit 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by
KASAN") correctly identified and analyzed this bug. However the attempted
fix only NULLed out a local variable, missing the fact that
drvdata->attn_data is a struct, not a pointer.
NULL out the correct pointer in the driver data to prevent the attention
functions from copying from it.
Fixes: 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by KASAN")
Fixes: b908d3cd81 ("Input: synaptics-rmi4 - allow to add attention data")
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200427145537.1.Ic8f898e0147beeee2c005ee7b20f1aebdef1e7eb@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The previous patch "c5ccf2ad3d33 (Input: synaptics-rmi4 - switch to
reduced reporting mode)" enabled reduced reporting mode unintentionally
on some devices, if the firmware was configured with default Delta X/Y
threshold values. The result unintentionally degrade the performance of
some touchpads.
This patch checks to see that the driver is modifying the delta X/Y
thresholds before modifying the reporting mode.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Fixes: c5ccf2ad3d ("Input: synaptics-rmi4 - switch to reduced reporting mode")
Link: https://lore.kernel.org/r/20200312005549.29922-1-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the distance thresholds are set the controller must be in reduced
reporting mode for them to have any effect on the interrupt generation.
This has a potentially large impact on the number of events the host
needs to process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200120111628.18376-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit a284e11c37.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c37 ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875a (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v4l2-compliance utility reported several V4L2 API compliance
issues:
- the sequence counter wasn't filled in
- the sequence counter wasn't reset to 0 at the start of streaming
- the returned field value wasn't set to V4L2_FIELD_NONE
- the timestamp wasn't set
- the payload size was undefined if an error was returned
- min_buffers_needed doesn't need to be initialized
Fix these issues.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de
Link: https://lore.kernel.org/r/20191119105118.54285-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.
Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The body of the for loop is only ever run once as the second standard_report
element is never changed from its initial zero init, so the loop condition is
never satisfies after the first run. Equally the start member of the first
element is never changed from 0, so the index offset is always a constant 0.
Remove this needless obfuscation of the code and write it in a straight
forward manner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191104114454.10500-3-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-3-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Simon Wood <simon@mungewell.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rmi_process_interrupt_requests() calls handle_nested_irq() for
each interrupt status bit it finds. If the irq domain mapping for
this bit had not yet been set up, then it ends up calling
handle_nested_irq(0), which causes a NULL pointer dereference.
There's already code that masks the irq_status bits coming out of the
hardware with current_irq_mask, presumably to avoid this situation.
However current_irq_mask seems to more reflect the actual mask set
in the hardware rather than the IRQs software has set up and registered
for. For example, in rmi_driver_reset_handler(), the current_irq_mask
is initialized based on what is read from the hardware. If the reset
value of this mask enables IRQs that Linux has not set up yet, then
we end up in this situation.
There appears to be a third unused bitmask that used to serve this
purpose, fn_irq_bits. Use that bitmask instead of current_irq_mask
to avoid calling handle_nested_irq() on IRQs that have not yet been
set up.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20191008223657.163366-1-evgreen@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The function rmi_2d_sensor_set_input_params is declared static and marked
EXPORT_SYMBOL_GPL, which is at best an odd combination. Because the
function is not used outside of the drivers/input/rmi4/rmi_2d_sensor.c
file it is defined in, this commit removes the EXPORT_SYMBOL_GPL() marking.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0idTweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZesIAJDKicw2Voyx8K8m
3pXSK+71RuO/d3Y9M51mdfTMKRP4PHR9/4wVZ9wHPwC4dV6wxgsmIYCF69a1Wety
LD1MpDCP1DK5wVfPNKVX2xmj7ua6iutPtSsJHzdzM2TlscgsrFKjmUccqJ5JLwL5
c34nqwXWnzzRyI5Ga9cQSlwzAXq0vDHXyML3AnCosSsLX0lKFrHlK1zttdOPNkfj
dXRN62g3q+9kVQozzhDXb8atZZ7IkBk8Q0lujpNXW83Ci1VjaVNv3SB8GZTXIlLj
U15VdyuwfJDfpBgFBN6/unzVaAB6FFrEKy0jT1aeTyKarMKDKgOnJjn10aKjDNno
/bXsKKc=
=TVqV
-----END PGP SIGNATURE-----
Merge tag 'v5.2' into next
Sync up with mainline to resolve conflicts in iforce driver.
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/rmi4/rmi_f12.c: In function rmi_f12_read_sensor_tuning:
drivers/input/rmi4/rmi_f12.c:76:6: warning: variable sensor_flags set but not used [-Wunused-but-set-variable]
It's not used since introduction in
commit b43d2c1e93 ("Input: synaptics-rmi4 - add support for F12")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzPgx4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf8IH/jkes7tKj7pWfsNW
uMjbm5T+Jh26sntRj+3OWOxcHRlejTH2MammnA9GIspBfF5LXkkmk40eeYhnTiVN
SzZqSFNLO0tRIHsd7hbxhTyOzHcWmymoEqY1jb8IPMyM5BB8TiS+1C0AVlOW1P/f
TO1gRcrddu1j80uCInRzNX5eAlvfrU4nK6GxjFdmy6b/bgYQiPfNA+jZbCWxc+48
ivBn9ifFCKlDzki81Dmi5R98c4R9UU3Z5LsqHjC4RIV64hpHdEwnOIkXQ+XY5mW9
7EOT1v6hJGch1ulH27ypgSZ7fhSCSYQJIY/LNWeJtdVclvlVepb2Vrx/8NUN60qC
E0MEn1Y=
=mCkr
-----END PGP SIGNATURE-----
Merge tag 'v5.1' into next
Sync up with mainline to bring in the latest APIs.
Currently any changed config register values don't take effect, as the
function to write them back is called with the wrong register offset.
Fixes: ff8f83708b (Input: synaptics-rmi4 - add support for 2D
sensors and F11)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not enumerate all formats, some of which the device may not even
support. Instead, only report the one fixed format of the currently
selected input that will survive try_fmt/s_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't set an initial video format until s_input is called:
$ v4l2-ctl -d /dev/v4l-touch0 --get-input
Video input : 0 (Normalized 16-Bit Image: ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 0/0
Pixel Format : ''
[...]
$ v4l2-ctl -d /dev/v4l-touch0 --set-input 0
Video input set to 0 (Normalized 16-Bit Image: Touch, ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 71/40
Pixel Format : 'TD16'
[...]
To fix this, initialize the video format to input 0 during probe.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
The documentation for the touchscreen-swapped-x-y property states that
swapping is done after inverting if both are used. RMI4 did it the other
way around, leading to inconsistent behavior with regard to other
touchscreens.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The error return code PTR_ERR(data->irqdomain) is always 0 since
data->irqdomain is equal to NULL in this error handling case.
Fixes: 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution to irq_domain")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the RMI driver to use the standard mechanism for
distributing IRQs to the various functions.
Tested on:
* S7300 (F11, F34, F54)
* S7817 (F12, F34, F54)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Acked-by: Christopher Heiny <cheiny@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When extending the rmi_spi buffers, we must check that no out of memory
error occurs, otherwise we may access data above the currently allocated
memory.
Propagate the error code returned by 'rmi_spi_manage_pools()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
