eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab20 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab20 ("gro: Add internal interfaces for VLAN")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only first fragment has the sport/dport information,
not the following ones.
If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.
This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.
It is also visible if any routing rule wants dissection
and sport or dport.
See commit 5e5d6fed37 ("ipv6: route: dissect flow
in input path if fib rules need it") for details.
[edumazet] rewrote the changelog completely.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: bf2ae2e4bf ("sock_diag: request _diag module only when the family or proto has been registered")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to discard using source link local address when
remote netconsole IPv6 address is set to be link local one.
The patch allows administrators to use IPv6 netconsole without
explicitly configuring source address:
netconsole=@/,@fe80::5054:ff:fe2f:6012/
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.
Fix it by partially restoring the previous behavior before
commit c63586dc9b ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.
[1]:
unreferenced object 0xffff88001322a200 (size 96):
comm "sshd", pid 1484, jiffies 4296032768 (age 1432.542s)
hex dump (first 32 bytes):
00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de ................
18 09 41 36 00 88 ff ff 18 09 41 36 00 88 ff ff ..A6......A6....
backtrace:
[<0000000095846b39>] kmem_cache_alloc_trace+0x151/0x220
[<000000007d12709f>] inet6_dump_fib+0x68d/0x940
[<000000002775a316>] rtnl_dump_all+0x1d9/0x2d0
[<00000000d7cd302b>] netlink_dump+0x945/0x11a0
[<000000002f43485f>] __netlink_dump_start+0x55d/0x800
[<00000000f76bbeec>] rtnetlink_rcv_msg+0x4fa/0xa00
[<000000009b5761f3>] netlink_rcv_skb+0x29c/0x420
[<0000000087a1dae1>] rtnetlink_rcv+0x15/0x20
[<00000000691b703b>] netlink_unicast+0x4e3/0x6c0
[<00000000b5be0204>] netlink_sendmsg+0x7f2/0xba0
[<0000000096d2aa60>] sock_sendmsg+0xba/0xf0
[<000000008c1b786f>] __sys_sendto+0x1e4/0x330
[<0000000019587b3f>] __x64_sys_sendto+0xe1/0x1a0
[<00000000071f4d56>] do_syscall_64+0x9f/0x300
[<000000002737577f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<0000000057587684>] 0xffffffffffffffff
Fixes: c63586dc9b ("net: rtnl_dump_all needs to propagate error from dumpit function")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kernel-doc warning:
net/core/skbuff.c:4953: warning: Function parameter or member 'skb' not described in 'skb_gso_size_check'
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an FDB entry is configured, the address is validated to have the
length of an Ethernet address, but the device for which the address is
configured can be of any type.
The above can result in the use of uninitialized memory when the address
is later compared against existing addresses since 'dev->addr_len' is
used and it may be greater than ETH_ALEN, as with ip6tnl devices.
Fix this by making sure that FDB entries are only configured for
Ethernet devices.
BUG: KMSAN: uninit-value in memcmp+0x11d/0x180 lib/string.c:863
CPU: 1 PID: 4318 Comm: syz-executor998 Not tainted 4.19.0-rc3+ #49
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x14b/0x190 lib/dump_stack.c:113
kmsan_report+0x183/0x2b0 mm/kmsan/kmsan.c:956
__msan_warning+0x70/0xc0 mm/kmsan/kmsan_instr.c:645
memcmp+0x11d/0x180 lib/string.c:863
dev_uc_add_excl+0x165/0x7b0 net/core/dev_addr_lists.c:464
ndo_dflt_fdb_add net/core/rtnetlink.c:3463 [inline]
rtnl_fdb_add+0x1081/0x1270 net/core/rtnetlink.c:3558
rtnetlink_rcv_msg+0xa0b/0x1530 net/core/rtnetlink.c:4715
netlink_rcv_skb+0x36e/0x5f0 net/netlink/af_netlink.c:2454
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4733
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x1638/0x1720 net/netlink/af_netlink.c:1343
netlink_sendmsg+0x1205/0x1290 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
__sys_sendmsg net/socket.c:2152 [inline]
__do_sys_sendmsg net/socket.c:2161 [inline]
__se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x440ee9
Code: e8 cc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 bb 0a fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff6a93b518 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000440ee9
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000003
RBP: 0000000000000000 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 000000000000b4b0
R13: 0000000000401ec0 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:256 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:181
kmsan_kmalloc+0x98/0x100 mm/kmsan/kmsan_hooks.c:91
kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:100
slab_post_alloc_hook mm/slab.h:446 [inline]
slab_alloc_node mm/slub.c:2718 [inline]
__kmalloc_node_track_caller+0x9e7/0x1160 mm/slub.c:4351
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2f5/0x9e0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:996 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline]
netlink_sendmsg+0xb49/0x1290 net/netlink/af_netlink.c:1883
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg net/socket.c:631 [inline]
___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
__sys_sendmsg net/socket.c:2152 [inline]
__do_sys_sendmsg net/socket.c:2161 [inline]
__se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
v2:
* Make error message more specific (David)
Fixes: 090096bf3d ("net: generic fdb support for drivers without ndo_fdb_<op>")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+3a288d5f5530b901310e@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+d53ab4e92a1db04110ff@syzkaller.appspotmail.com
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like with normal GRO processing, we have to initialize
skb->next to NULL when we unlink overflow packets from the
GRO hash lists.
Fixes: d4546c2509 ("net: Convert GRO SKB handling to list_head.")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-10-27
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix toctou race in BTF header validation, from Martin and Wenwen.
2) Fix devmap interface comparison in notifier call which was
neglecting netns, from Taehee.
3) Several fixes in various places, for example, correcting direct
packet access and helper function availability, from Daniel.
4) Fix BPF kselftest config fragment to include af_xdp and sockmap,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"What better way to start off a weekend than with some networking bug
fixes:
1) net namespace leak in dump filtering code of ipv4 and ipv6, fixed
by David Ahern and Bjørn Mork.
2) Handle bad checksums from hardware when using CHECKSUM_COMPLETE
properly in UDP, from Sean Tranchetti.
3) Remove TCA_OPTIONS from policy validation, it turns out we don't
consistently use nested attributes for this across all packet
schedulers. From David Ahern.
4) Fix SKB corruption in cadence driver, from Tristram Ha.
5) Fix broken WoL handling in r8169 driver, from Heiner Kallweit.
6) Fix OOPS in pneigh_dump_table(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
net/neigh: fix NULL deref in pneigh_dump_table()
net: allow traceroute with a specified interface in a vrf
bridge: do not add port to router list when receives query with source 0.0.0.0
net/smc: fix smc_buf_unuse to use the lgr pointer
ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are called
net/{ipv4,ipv6}: Do not put target net if input nsid is invalid
lan743x: Remove SPI dependency from Microchip group.
drivers: net: remove <net/busy_poll.h> inclusion when not needed
net: phy: genphy_10g_driver: Avoid NULL pointer dereference
r8169: fix broken Wake-on-LAN from S5 (poweroff)
octeontx2-af: Use GFP_ATOMIC under spin lock
net: ethernet: cadence: fix socket buffer corruption problem
net/ipv6: Allow onlink routes to have a device mismatch if it is the default route
net: sched: Remove TCA_OPTIONS from policy
ice: Poll for link status change
ice: Allocate VF interrupts and set queue map
ice: Introduce ice_dev_onetime_setup
net: hns3: Fix for warning uninitialized symbol hw_err_lst3
octeontx2-af: Copy the right amount of memory
net: udp: fix handling of CHECKSUM_COMPLETE packets
...
Commit cd33943176 ("bpf: introduce the bpf_get_local_storage()
helper function") enabled the bpf_get_local_storage() helper also
for BPF program types where it does not make sense to use them.
They have been added both in sk_skb_func_proto() and sk_msg_func_proto()
even though both program types are not invoked in combination with
cgroups, and neither through BPF_PROG_RUN_ARRAY(). In the latter the
bpf_cgroup_storage_set() is set shortly before BPF program invocation.
Later, the helper bpf_get_local_storage() retrieves this prior set
up per-cpu pointer and hands the buffer to the BPF program. The map
argument in there solely retrieves the enum bpf_cgroup_storage_type
from a local storage map associated with the program and based on the
type returns either the global or per-cpu storage. However, there
is no specific association between the program's map and the actual
content in bpf_cgroup_storage[].
Meaning, any BPF program that would have been properly run from the
cgroup side through BPF_PROG_RUN_ARRAY() where bpf_cgroup_storage_set()
was performed, and that is later unloaded such that prog / maps are
teared down will cause a use after free if that pointer is retrieved
from programs that are not run through BPF_PROG_RUN_ARRAY() but have
the cgroup local storage helper enabled in their func proto.
Lets just remove it from the two sock_map program types to fix it.
Auditing through the types where this helper is enabled, it appears
that these are the only ones where it was mistakenly allowed.
Fixes: cd33943176 ("bpf: introduce the bpf_get_local_storage() helper function")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Roman Gushchin <guro@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull cgroup updates from Tejun Heo:
"All trivial changes - simplification, typo fix and adding
cond_resched() in a netclassid update loop"
* 'for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, netclassid: add a preemption point to write_classid
rdmacg: fix a typo in rdmacg documentation
cgroup: Simplify cgroup_ancestor
Rick reported that the BPF JIT could potentially fill the entire module
space with BPF programs from unprivileged users which would prevent later
attempts to load normal kernel modules or privileged BPF programs, for
example. If JIT was enabled but unsuccessful to generate the image, then
before commit 290af86629 ("bpf: introduce BPF_JIT_ALWAYS_ON config")
we would always fall back to the BPF interpreter. Nowadays in the case
where the CONFIG_BPF_JIT_ALWAYS_ON could be set, then the load will abort
with a failure since the BPF interpreter was compiled out.
Add a global limit and enforce it for unprivileged users such that in case
of BPF interpreter compiled out we fail once the limit has been reached
or we fall back to BPF interpreter earlier w/o using module mem if latter
was compiled in. In a next step, fair share among unprivileged users can
be resolved in particular for the case where we would fail hard once limit
is reached.
Fixes: 290af86629 ("bpf: introduce BPF_JIT_ALWAYS_ON config")
Fixes: 0a14842f5a ("net: filter: Just In Time compiler for x86-64")
Co-Developed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jann Horn <jannh@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Given this seems to be quite fragile and can easily slip through the
cracks, lets make direct packet write more robust by requiring that
future program types which allow for such write must provide a prologue
callback. In case of XDP and sk_msg it's noop, thus add a generic noop
handler there. The latter starts out with NULL data/data_end unconditionally
when sg pages are shared.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit b39b5f411d ("bpf: add cg_skb_is_valid_access for
BPF_PROG_TYPE_CGROUP_SKB") added support for returning pkt pointers
for direct packet access. Given this program type is allowed for both
unprivileged and privileged users, we shouldn't allow unprivileged
ones to use it, e.g. besides others one reason would be to avoid any
potential speculation on the packet test itself, thus guard this for
root only.
Fixes: b39b5f411d ("bpf: add cg_skb_is_valid_access for BPF_PROG_TYPE_CGROUP_SKB")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an address, route or netconf dump request is sent for AF_UNSPEC, then
rtnl_dump_all is used to do the dump across all address families. If one
of the dumpit functions fails (e.g., invalid attributes in the dump
request) then rtnl_dump_all needs to propagate that error so the user
gets an appropriate response instead of just getting no data.
Fixes: effe679266 ("net: Enable kernel side filtering of route dumps")
Fixes: 5fcd266a9f ("net/ipv4: Add support for dumping addresses for a specific device")
Fixes: 6371a71f3a ("net/ipv6: Add support for dumping addresses for a specific device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Implement two new kind of BPF maps, that is, queue and stack
map along with new peek, push and pop operations, from Mauricio.
2) Add support for MSG_PEEK flag when redirecting into an ingress
psock sk_msg queue, and add a new helper bpf_msg_push_data() for
insert data into the message, from John.
3) Allow for BPF programs of type BPF_PROG_TYPE_CGROUP_SKB to use
direct packet access for __skb_buff, from Song.
4) Use more lightweight barriers for walking perf ring buffer for
libbpf and perf tool as well. Also, various fixes and improvements
from verifier side, from Daniel.
5) Add per-symbol visibility for DSO in libbpf and hide by default
global symbols such as netlink related functions, from Andrey.
6) Two improvements to nfp's BPF offload to check vNIC capabilities
in case prog is shared with multiple vNICs and to protect against
mis-initializing atomic counters, from Jakub.
7) Fix for bpftool to use 4 context mode for the nfp disassembler,
also from Jakub.
8) Fix a return value comparison in test_libbpf.sh and add several
bpftool improvements in bash completion, documentation of bpf fs
restrictions and batch mode summary print, from Quentin.
9) Fix a file resource leak in BPF selftest's load_kallsyms()
helper, from Peng.
10) Fix an unused variable warning in map_lookup_and_delete_elem(),
from Alexei.
11) Fix bpf_skb_adjust_room() signature in BPF UAPI helper doc,
from Nicolas.
12) Add missing executables to .gitignore in BPF selftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern's dump indexing bug fix in 'net' overlapped the
change of the function signature of inet6_fill_ifaddr() in
'net-next'. Trivially resolved.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8e326289e3.
This patch results in unnecessary netlink notification when one
tries to delete a neigh entry already in NUD_FAILED state. Found
this with a buggy app that tries to delete a NUD_FAILED entry
repeatedly. While the notification issue can be fixed with more
checks, adding more complexity here seems unnecessary. Also,
recent tests with other changes in the neighbour code have
shown that the INCOMPLETE and PROBE checks are good enough for
the original issue.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows user to push data into a msg using sk_msg program types.
The format is as follows,
bpf_msg_push_data(msg, offset, len, flags)
this will insert 'len' bytes at offset 'offset'. For example to
prepend 10 bytes at the front of the message the user can,
bpf_msg_push_data(msg, 0, 10, 0);
This will invalidate data bounds so BPF user will have to then recheck
data bounds after calling this. After this the msg size will have been
updated and the user is free to write into the added bytes. We allow
any offset/len as long as it is within the (data, data_end) range.
However, a copy will be required if the ring is full and its possible
for the helper to fail with ENOMEM or EINVAL errors which need to be
handled by the BPF program.
This can be used similar to XDP metadata to pass data between sk_msg
layer and lower layers.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We've been getting checksum errors involving small UDP packets, usually
59B packets with 1 extra non-zero padding byte. netdev_rx_csum_fault()
has been complaining that HW is providing bad checksums. Turns out the
problem is in pskb_trim_rcsum_slow(), introduced in commit 88078d98d1
("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends").
The source of the problem is that when the bytes we are trimming start
at an odd address, as in the case of the 1 padding byte above,
skb_checksum() returns a byte-swapped value. We cannot just combine this
with skb->csum using csum_sub(). We need to use csum_block_sub() here
that takes into account the parity of the start address and handles the
swapping.
Matches existing code in __skb_postpull_rcsum() and esp_remove_trailer().
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before using the psock returned by sk_psock_get() when adding it to a
sockmap we need to ensure it is actually a sockmap based psock.
Previously we were only checking this after incrementing the reference
counter which was an error. This resulted in a slab-out-of-bounds
error when the psock was not actually a sockmap type.
This moves the check up so the reference counter is only used
if it is a sockmap psock.
Eric reported the following KASAN BUG,
BUG: KASAN: slab-out-of-bounds in atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
BUG: KASAN: slab-out-of-bounds in refcount_inc_not_zero_checked+0x97/0x2f0 lib/refcount.c:120
Read of size 4 at addr ffff88019548be58 by task syz-executor4/22387
CPU: 1 PID: 22387 Comm: syz-executor4 Not tainted 4.19.0-rc7+ #264
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
kasan_check_read+0x11/0x20 mm/kasan/kasan.c:272
atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
refcount_inc_not_zero_checked+0x97/0x2f0 lib/refcount.c:120
sk_psock_get include/linux/skmsg.h:379 [inline]
sock_map_link.isra.6+0x41f/0xe30 net/core/sock_map.c:178
sock_hash_update_common+0x19b/0x11e0 net/core/sock_map.c:669
sock_hash_update_elem+0x306/0x470 net/core/sock_map.c:738
map_update_elem+0x819/0xdf0 kernel/bpf/syscall.c:818
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF programs of BPF_PROG_TYPE_CGROUP_SKB need to access headers in the
skb. This patch enables direct access of skb for these programs.
Two helper functions bpf_compute_and_save_data_end() and
bpf_restore_data_end() are introduced. There are used in
__cgroup_bpf_run_filter_skb(), to compute proper data_end for the
BPF program, and restore original data afterwards.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Queue/stack maps implement a FIFO/LIFO data storage for ebpf programs.
These maps support peek, pop and push operations that are exposed to eBPF
programs through the new bpf_map[peek/pop/push] helpers. Those operations
are exposed to userspace applications through the already existing
syscalls in the following way:
BPF_MAP_LOOKUP_ELEM -> peek
BPF_MAP_LOOKUP_AND_DELETE_ELEM -> pop
BPF_MAP_UPDATE_ELEM -> push
Queue/stack maps are implemented using a buffer, tail and head indexes,
hence BPF_F_NO_PREALLOC is not supported.
As opposite to other maps, queue and stack do not use RCU for protecting
maps values, the bpf_map[peek/pop] have a ARG_PTR_TO_UNINIT_MAP_VALUE
argument that is a pointer to a memory zone where to save the value of a
map. Basically the same as ARG_PTR_TO_UNINIT_MEM, but the size has not
be passed as an extra argument.
Our main motivation for implementing queue/stack maps was to keep track
of a pool of elements, like network ports in a SNAT, however we forsee
other use cases, like for exampling saving last N kernel events in a map
and then analysing from userspace.
Signed-off-by: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6fe9487892.
It is causing more serious regressions than the RCU warning
it is fixing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_pacing_rate has beed introduced as a u32 field in 2013,
effectively limiting per flow pacing to 34Gbit.
We believe it is time to allow TCP to pace high speed flows
on 64bit hosts, as we now can reach 100Gbit on one TCP flow.
This patch adds no cost for 32bit kernels.
The tcpi_pacing_rate and tcpi_max_pacing_rate were already
exported as 64bit, so iproute2/ss command require no changes.
Unfortunately the SO_MAX_PACING_RATE socket option will stay
32bit and we will need to add a new option to let applications
control high pacing rates.
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 1787144 10.246.9.76:49992 10.246.9.77:36741
timer:(on,003ms,0) ino:91863 sk:2 <->
skmem:(r0,rb540000,t66440,tb2363904,f605944,w1822984,o0,bl0,d0)
ts sack bbr wscale:8,8 rto:201 rtt:0.057/0.006 mss:1448
rcvmss:536 advmss:1448
cwnd:138 ssthresh:178 bytes_acked:256699822585 segs_out:177279177
segs_in:3916318 data_segs_out:177279175
bbr:(bw:31276.8Mbps,mrtt:0,pacing_gain:1.25,cwnd_gain:2)
send 28045.5Mbps lastrcv:73333
pacing_rate 38705.0Mbps delivery_rate 22997.6Mbps
busy:73333ms unacked:135 retrans:0/157 rcv_space:14480
notsent:2085120 minrtt:0.013
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.
This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.
Fixes: f38d138a7d ("net/ethtool: support set coalesce per queue")
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_get_rxnfc(), the eth command 'cmd' is compared against
'ETHTOOL_GRXFH' to see whether it is necessary to adjust the variable
'info_size'. Then the whole structure of 'info' is copied from the
user-space buffer 'useraddr' with 'info_size' bytes. In the following
execution, 'info' may be copied again from the buffer 'useraddr' depending
on the 'cmd' and the 'info.flow_type'. However, after these two copies,
there is no check between 'cmd' and 'info.cmd'. In fact, 'cmd' is also
copied from the buffer 'useraddr' in dev_ethtool(), which is the caller
function of ethtool_get_rxnfc(). Given that 'useraddr' is in the user
space, a malicious user can race to change the eth command in the buffer
between these copies. By doing so, the attacker can supply inconsistent
data and cause undefined behavior because in the following execution 'info'
will be passed to ops->get_rxnfc().
This patch adds a necessary check on 'info.cmd' and 'cmd' to confirm that
they are still same after the two copies in ethtool_get_rxnfc(). Otherwise,
an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6acc9b432e ("bpf: Add helper to retrieve socket in BPF")
mistakenly passed the destination port in network byte-order to the IPv6
TCP/UDP socket lookup functions, which meant that BPF writers would need
to either manually swap the byte-order of this field or otherwise IPv6
sockets could not be located via this helper.
Fix the issue by swapping the byte-order appropriately in the helper.
This also makes the API more consistent with the IPv4 version.
Fixes: 6acc9b432e ("bpf: Add helper to retrieve socket in BPF")
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This is a more complete fix than d71019b54b ("net: core: Fix build
with CONFIG_IPV6=m"), so that IPv6 sockets may be looked up if the IPv6
module is loaded (not just if it's compiled in).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Convert kTLS over to make use of sk_msg interface for plaintext and
encrypted scattergather data, so it reuses all the sk_msg helpers
and data structure which later on in a second step enables to glue
this to BPF.
This also allows to remove quite a bit of open coded helpers which
are covered by the sk_msg API. Recent changes in kTLs 80ece6a03a
("tls: Remove redundant vars from tls record structure") and
4e6d47206c ("tls: Add support for inplace records encryption")
changed the data path handling a bit; while we've kept the latter
optimization intact, we had to undo the former change to better
fit the sk_msg model, hence the sg_aead_in and sg_aead_out have
been brought back and are linked into the sk_msg sgs. Now the kTLS
record contains a msg_plaintext and msg_encrypted sk_msg each.
In the original code, the zerocopy_from_iter() has been used out
of TX but also RX path. For the strparser skb-based RX path,
we've left the zerocopy_from_iter() in decrypt_internal() mostly
untouched, meaning it has been moved into tls_setup_from_iter()
with charging logic removed (as not used from RX). Given RX path
is not based on sk_msg objects, we haven't pursued setting up a
dummy sk_msg to call into sk_msg_zerocopy_from_iter(), but it
could be an option to prusue in a later step.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a generic sk_msg layer, and convert current sockmap and later
kTLS over to make use of it. While sk_buff handles network packet
representation from netdevice up to socket, sk_msg handles data
representation from application to socket layer.
This means that sk_msg framework spans across ULP users in the
kernel, and enables features such as introspection or filtering
of data with the help of BPF programs that operate on this data
structure.
Latter becomes in particular useful for kTLS where data encryption
is deferred into the kernel, and as such enabling the kernel to
perform L7 introspection and policy based on BPF for TLS connections
where the record is being encrypted after BPF has run and came to
a verdict. In order to get there, first step is to transform open
coding of scatter-gather list handling into a common core framework
that subsystems can use.
The code itself has been split and refactored into three bigger
pieces: i) the generic sk_msg API which deals with managing the
scatter gather ring, providing helpers for walking and mangling,
transferring application data from user space into it, and preparing
it for BPF pre/post-processing, ii) the plain sock map itself
where sockets can be attached to or detached from; these bits
are independent of i) which can now be used also without sock
map, and iii) the integration with plain TCP as one protocol
to be used for processing L7 application data (later this could
e.g. also be extended to other protocols like UDP). The semantics
are the same with the old sock map code and therefore no change
of user facing behavior or APIs. While pursuing this work it
also helped finding a number of bugs in the old sockmap code
that we've fixed already in earlier commits. The test_sockmap
kselftest suite passes through fine as well.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Dan Carpenter reports:
The patch 6acc9b432e: "bpf: Add helper to retrieve socket in BPF"
from Oct 2, 2018, leads to the following Smatch complaint:
net/core/filter.c:4893 bpf_sk_lookup()
error: we previously assumed 'skb->dev' could be null (see line 4885)
Fix this issue by checking skb->dev before using it.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLM_F_DUMP_PROPER_HDR netlink flag was replaced by a setsockopt.
Update the comment in rtnl_stats_dump.
Fixes: 841891ec0c ("rtnetlink: Update rtnl_stats_dump for strict data checking")
Reported-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting of local variable ifm to after the message parsing in
valid_fdb_dump_legacy. Avoid potential future use of unchecked variable.
Fixes: 8dfbda19a2 ("rtnetlink: Move input checking for rtnl_fdb_dump to helper")
Reported-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink string param buffer is allocated at the size of
DEVLINK_PARAM_MAX_STRING_VALUE. Add helper function which makes sure
this size is not exceeded.
Renamed DEVLINK_PARAM_MAX_STRING_VALUE to
__DEVLINK_PARAM_MAX_STRING_VALUE to emphasize that it should be used by
devlink only. The driver should use the helper function instead to
verify it doesn't exceed the allowed length.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
