If set active without increase the usage count of pm, the dont use
autosuspend function will call the suspend callback to close the two
clocks of spi because the usage count is reduced to -1.
This will cause the warning dump below when the defer-probe occurs.
[ 129.379701] ecspi2_root_clk already disabled
[ 129.384005] WARNING: CPU: 1 PID: 33 at drivers/clk/clk.c:952 clk_core_disable+0xa4/0xb0
So add the get noresume function before set active.
Fixes: 43b6bf406c spi: imx: fix runtime pm support for !CONFIG_PM
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20201124085247.18025-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201116202606.29888-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in callers(spi_imx_prepare_message and
spi_imx_remove), so we should fix it.
Fixes: 525c9e5a32 ("spi: imx: enable runtime pm support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102145835.4765-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
525c9e5a32 introduced pm_runtime support for the i.MX SPI driver. With
this pm_runtime is used to bring up the clocks initially. When CONFIG_PM
is disabled the clocks are no longer enabled and the driver doesn't work
anymore. Fix this by enabling the clocks in the probe function and
telling pm_runtime that the device is active using
pm_runtime_set_active().
Fixes: 525c9e5a32 spi: imx: enable runtime pm support
Tested-by: Christian Eggers <ceggers@arri.de> [tested for !CONFIG_PM only]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20201021104513.21560-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the SPI controller has has_dmamode = true and spi_bitbang_start() fails
in spi_imx_probe(), then the driver must release the DMA channels acquired
in spi_imx_sdma_init() by calling spi_imx_sdma_exit() in the fail path.
Fixes: f62caccd12 ("spi: spi-imx: add DMA support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Robin Gong <b38343@freescale.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20201005132229.513119-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200917202420.1914104-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point in printing a plain "probed" message on successful probe.
Just remove it and make the kernel log a bit less noisy.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200819123330.22880-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are cases that DMA is not used and the driver gracefully
falls back to PIO mode.
Do not treat it like an error message and move it to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200818223519.8737-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the two Freescale i.MX SPI drivers
Freescale i.MX (CONFIG_SPI_IMX) and Freescale i.MX LPSPI
(CONFIG_SPI_FSL_LPSPI) to use GPIO descriptors handled in
the SPI core for GPIO chip selects whether defined in
the device tree or a board file.
The reason why both are converted at the same time is
that they were both using the same platform data and
platform device population helpers when using
board files intertwining the code so this gives a cleaner
cut.
The platform device creation was passing a platform data
container from each boardfile down to the driver using
struct spi_imx_master from <linux/platform_data/spi-imx.h>,
but this was only conveying the number of chipselects and
an int * array of the chipselect GPIO numbers.
The imx27 and imx31 platforms had code passing the
now-unused platform data when creating the platform devices,
this has been repurposed to pass around GPIO descriptor
tables. The platform data struct that was just passing an
array of integers and number of chip selects for the GPIO
lines has been removed.
The number of chipselects used to be passed from the board
file, because this number also limits the number of native
chipselects that the platform can use. To deal with this we
just augment the i.MX (CONFIG_SPI_IMX) driver to support 3
chipselects if the platform does not define "num-cs" as a
device property (such as from the device tree). This covers
all the legacy boards as these use <= 3 native chip selects
(or GPIO lines, and in that case the number of chip selects
is determined by the core from the number of available
GPIO lines). Any new boards should use device tree, so
this is a reasonable simplification to cover all old
boards.
The LPSPI driver never assigned the number of chipselects
and thus always fall back to the core default of 1 chip
select if no GPIOs are defined in the device tree.
The Freescale i.MX driver was already partly utilizing
the SPI core to obtain the GPIO numbers from the device tree,
so this completes the transtion to let the core handle all
of it.
All board files and the core i.MX boardfile registration
code is augmented to account for these changes.
This has been compile-tested with the imx_v4_v5_defconfig
and the imx_v6_v7_defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Trent Piepho <tpiepho@impinj.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Link: https://lore.kernel.org/r/20200625200252.207614-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback pio feature in case dma transfer failed before start.
Besides, another whole pio transfer including setup_transfer will be
issued by spi core, no need to restore jobs like commit bcd8e7761e ("spi:
imx: fallback to PIO if dma setup failure").
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-3-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fallback to PIO in case dma setup failed. For example, sdma firmware not
updated but ERR009165 workaroud added in kernel.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-imx.c:1233:2-17: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-imx.c:1235:2-17: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 71abd29057 ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer. In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.
However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.
Change it to empty the FIFO and throw away the data. Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.
There is another issue, which affects master mode when switching from
DMA to PIO. There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner. I don't know
why this data is unexpectedly in the FIFO. It's likely there is a
different bug or erratum responsible for that. But regardless of that,
I think this is proper fix the for bug at hand here.
Fixes: 71abd29057 ("spi: imx: Add support for SPI Slave mode")
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the boolean module parameter "use_dma" to control the use of DMA by
the driver. There are about two dozen other drivers with a "use_dma"
parameter of some sort.
DMA may allow faster and more efficient transfers than using PIO, but it
also adds overhead for small transfers.
High speed receive operations may be less likely to have issues with
FIFO overflow when using DMA than when using PIO.
The eCSPI appears to insert a 4 bit pause after each word in DMA mode,
not done in PIO mode, which can make DMA transfers 50% slower than PIO.
In some cases DMA may be a net win while in others PIO might be. It
depends on the application. So allow DMA to be enabled or disabled at
the driver level. The default will be to have it enabled when possible.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data's member variable just caches the transfer's speed_hz
member. All users of the former now have access directly to the latter.
So fix them to use the uncached value and remove the cache.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The config callback is called once per transfer while some things can (and
should) be done on a per message manner. To have unambiguous naming in the
end include "transfer" in the callback's name and rename the
implementations accordingly. Also pass the driver struct and transfer
which allows further simplifications in the following patch.
There is no change in behavior intended here.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change fixes some random style issues that I noticed while debugging
the driver: Remove some double spaces, use tabs for indention instead
of spaces if possible, fix comment style.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The relevant difference between prepare_message and config is that the
former is run before the CS signal is asserted. So the polarity of the
CLK line must be configured in prepare_message as an edge generated by
config might already result in a latch of the MOSI line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is just preparatory work which allows to move some initialisation
that currently is done in the per transfer hook .config to an earlier
point in time in the next few patches. There is no change in behaviour
introduced by this patch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.
This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.
With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).
The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.
With this method, the read_u32 field is no longer necessary, and is
removed.
This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_imx_can_dma function computes the watermark level so that
the transfer will fit in exactly N bursts (without a remainder).
The smallest watermark level possible being one FIFO entry per burst, we
can't never have a case where the transfer size isn't divsiible by 1.
Remove the extra check for the wml being different than 0.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.
This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.
This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.
This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.
With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some fields in struct spi_imx_data are assigned a different value twice
in a row, in spi_imx_setupxfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now i.MX SPI controller can work in Slave mode.
Update MODULE_DESCRIPTION to "SPI Controller driver".
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since clocks are disabled except during message transfer clocks
are also disabled when spi_imx_remove gets called. Accessing
registers leads to a freeeze at least on a i.MX 6ULL. Enable
clocks before disabling accessing the MXC_CSPICTRL register.
Fixes: 9e556dcc55 ("spi: spi-imx: only enable the clocks when we start to transfer a message")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the array is not present, assume all chip selects are native. This
is the standard behavior for SPI masters configured via the device
tree and the behavior of this driver as well when it is configured via
device tree.
This reduces platform data vs DT differences and allows most of the
platform data based boards to remove their chip select arrays.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done. Add this
to the failure path.
Note that spi_bitbang_start() has to be called before requesting GPIOs
because the GPIO data in the spi master is populated when the master is
registed, and that doesn't happen until spi_bitbang_start() is called.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver will fail to load if no gpio chip selects are specified,
this patch changes this so that it no longer fails.
It's possible to use all native chip selects, in which case there is
no reason to have a gpio chip select array. This is what happens if
the *optional* device tree property "cs-gpios" is omitted.
The spi core already checks for the absence of gpio chip selects in
the master and assigns any slaves the gpio_cs value of -ENOENT.
Also have the driver respect the standard SPI device tree property "num-cs"
to allow setting the number of chip selects without using cs-gpios.
CC: Mark Brown <broonie@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 974488e4ce ("spi: imx: Fix failure path leak on GPIO request
error"), spi_bitbang_start() was moved later in the probe sequence. But
this doesn't work, as spi_bitbang_start() has to be called before
requesting GPIOs because the GPIO data in the spi master is populated when
the master is registed, and that doesn't happen until spi_bitbang_start()
is called. The default only works if one uses one CS.
So add a failure path call to spi_bitbang_stop() to fix the leak.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done.
Fix this by moving spi_bitbang_start() to after the code that requets
GPIOs. The GPIOs are dev managed and don't need explicit cleanup.
Since spi_bitbang_start() is now the last operation, it doesn't need
to be cleaned up in the failure path.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously i.MX SPI controller only works in Master mode.
This patch adds support to i.MX51, i.MX53 and i.MX6 ECSPI
controller to work also in Slave mode.
Currently SPI Slave mode support patch has the following limitations:
1. The stale data in RXFIFO will be dropped when the Slave does any new
transfer.
2. One transfer can be finished only after all transfer->len data been
transferred to master device
3. Slave device only accepts transfer->len data. Any data longer than this
from master device will be dropped. Any data shorter than this from
master will cause SPI to stuck due to mentioned HW limitation 2.
4. Only PIO transfer is supported in Slave mode.
5. Dynamic burst size adjust isn't supported in Slave mode.
Following HW limitation applies:
1. ECSPI has a HW issue when works in Slave mode, after 64
words written to TXFIFO, even TXFIFO becomes empty,
ECSPI_TXDATA keeps shift out the last word data,
so we have to disable ECSPI when in slave mode after the
transfer completes
2. Due to Freescale errata ERR003775 "eCSPI: Burst completion by Chip
Select (SS) signal in Slave mode is not functional" burst size must
be set exactly to the size of the transfer. This limit SPI transaction
with maximum 2^12 bits. This errata affects i.MX53 and i.MX6 ECSPI
controllers.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commonly used mechanism of specifying the hardware or native
chip-select on an SPI device in devicetree (that is "cs-gpios = <0>")
does not result in the native chip-select being configured for use.
So external SPI devices that require use of the native chip-select
will not work.
You can successfully specify native chip-selects if using a platform
setup by specifying the cs-gpio as negative offset by 32. And that
works correctly. You cannot use the same method in devicetree.
The logic in the spi-imx.c driver during probe uses core spi function
of_spi_register_master() in spi.c to parse the "cs-gpios" devicetree tag.
For valid GPIO values that will be recorded for use, all other entries in
the cs_gpios list will be set to -ENOENT. So entries like "<0>" will be
set to -ENOENT in the cs_gpios list.
When the SPI device registers are setup the code will use the GPIO
listed in the cs_gpios list for the desired chip-select. If the cs_gpio
is less then 0 then it is intended to be for a native chip-select, and
its cs_gpio value is added to 32 to get the chipselect number to use.
Problem is that with devicetree this can only ever be -ENOENT (which
is -2), and that alone results in an invalid chip-select number. But also
doesn't allow selection of the native chip-select at all.
To fix, if the cs_gpio specified for this spi device is not a
valid GPIO then use the "chip_select" (that is the native chip-select
number) for hardware setup.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added dynamic burst code produces a harmless warning
on big-endian configurations:
drivers/spi/spi-imx.c: In function 'spi_imx_buf_rx_swap_u32':
drivers/spi/spi-imx.c:284:15: error: unused variable 'bytes_per_word' [-Werror=unused-variable]
unsigned int bytes_per_word;
^~~~~~~~~~~~~~
drivers/spi/spi-imx.c: In function 'spi_imx_buf_tx_swap_u32':
drivers/spi/spi-imx.c:319:15: error: unused variable 'bytes_per_word' [-Werror=unused-variable]
unsigned int bytes_per_word;
This adds another #ifdef around the variable declaration matching
the one on the use.
Fixes: 1673c81d94 ("spi: imx: dynamic burst length adjust for PIO mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
previously burst length (BURST_LENGTH) is always set to equal
to bits_per_word, causes a 10us gap between each word in
transfer, which significantly affects performance.
This patch uses 32 bits transfer to simulate lower bits transfer,
and adjusts burst length runtimely to use biggeest burst length
as possible to reduce the gaps in transfer for PIO mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To run spi-loopback-tests on HW without modifications, we need to
disable Chip Select. This should avoid surprising side effects for SPI devices
by testing patterns.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
