According to usb_ep_set_halt()'s description,
__usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint
has any queue or data. Otherwise, this driver is possible to cause
just STALL without sending a short packet data on g_mass_storage driver,
and then a few resetting a device happens on a host side during
a usb enumaration.
Fixes: 2f98382dcd ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
had added a usbhsg_pipe_disable() calling into
__usbhsg_ep_set_halt_wedge() accidentally. But, this driver should
not call the usbhsg_pipe_disable() because the function discards
all queues. So, this patch removes it.
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=ciUl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: more changes for v5.3 merge window
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
usb: phy: phy-mxs-usb: add imx7ulp support
doc: dt-binding: mxs-usb-phy: add compatible for 7ulp
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb:cdns3 Add Cadence USB3 DRD Driver
usb:gadget Simplify usb_decode_get_set_descriptor function.
usb:gadget Patch simplify usb_decode_set_clear_feature function.
usb:gadget Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: dwc3: pci: add support for TigerLake Devices
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now the driver fixes the issue of the commit 482982062f ("usb:
gadget: renesas_usbhs: bugfix: don't modify platform data") by
using usbhs_mod_info.get_vbus, this patches uses the pointer
instead of copied value to avoid redundancy. Note that struct
renesas_usbhs_driver_param has to use copied value because
the driver has to set some members (e.g. buswait_bwait).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In device tree environment, the previous code allocates
renesas_usbhs_platform_info by using devm_kzalloc() and then copies
usbhs_of_data to the allocated memory. This reason is some values
(e.g. .platform_callback.get_vbus) are overwritten by the driver,
but the of_device_id.data is "const". Now the driver doesn't have
such a code, so this patch uses renesas_usbhs_platform_info on
of_device_id.data.
Note that the previous code set the pdev->dev.platform_data pointer
even if device tree environment, but the value is not used. So,
this patch also remove such a code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All platform related codes (rcar[23].c and rza{2}.c) has its own
.get_id function as "USBHS_GADGET". So, we can use a common
function for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c) to remove
usbhs_parse_dt(). So, this patch moves device tree properties
parsing to usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this can remove over 80 charactors in a line, this patch adds
struct device * declaration in usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c). So, to simplify
the source code, this patch adds a new flag has_new_pipe_configs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the dev_of_node macro instead of open coded
to be better.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now no one uses the type member so that this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To remove the type of renesas_usbhs_driver_param in the future, this
patch uses a specific flag "multi_clks".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The very old commit 482982062f ("usb: gadget: renesas_usbhs:
bugfix: don't modify platform data") changed to use copied whole
structures values to fix the "hung-up" issue. However, we also
can fix the issue if the driver copies the get_vbus function
pointer to the driver's value.
So, this patch adds get_vbus member into struct usbhs_mod_info and
use the pointer instead of struct renesas_usbhs_platform_callback.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, since other source code of this driver will use these
macros, this patch moves it to the header file.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notify_hotplug callback was supported in v3.10, but the last user
(armadillo800eva) was removed by the commit 1fa59bda21 ("ARM: shmobile:
Remove legacy board code for Armadillo-800 EVA"). So, this patch
removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the irq_vbus comments doesn't match with the current
implementation, this patch revises it. This patch also changes
new lines to reduce the source code lines.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid the error-proneness of calls to sizeof() in the memcpy,
this patch uses struct assignment instead of memcpy.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>---
This patch is based on Greg's linux-usb.git / usb-next branch.
Note that mod_host.c also has memcpy but we cannot use struct assignment
for it because the type of urb->setup_patcket is just "unsigned char *".
drivers/usb/renesas_usbhs/common.c | 13 ++++---------
1 file changed, 4 insertions(+), 9 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Controlling PWMEN/EXTLP (named as "has_otg") was supported in v3.2,
but the last user (kzm9g) was removed by the commit 30f8925a57
("ARM: shmobile: Remove legacy board code for KZM-A9-GT"). So, this
patch remove it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SUDMAC feature was supported in v3.10, but was never used by
any platform. So, this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/A2 is similar to the R-Car Gen3 with some small differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC have a CFIFO register that is byte addressable. This means
when the CFIFO access is set to 32-bit, you can write 8-bit values to
addresses CFIFO+0, CFIFO+1, CFIFO+2, CFIFO+3.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some SoC, CNEN must be set for USB Device mode operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move options from 'flags' field in private structure to param structure
where other options are already being kept.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a specific struct "usbhs_of_data" to add a new SoC
data easily instead of code basis in the future.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HS-USB found in RZ/G2E (a.k.a. r8a774c0) is very similar to the
one found in R-Car E3 (a.k.a. r8a77990), as it needs to release
the PLL reset by the UGCTRL register like R-Car E3, therefore add
r8a774c0 support in a similar fashion to what was done for the
r8a77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without CONFIG_PM, we get a new build warning here:
drivers/usb/renesas_usbhs/common.c:860:12: error: 'usbhsc_resume' defined but not used [-Werror=unused-function]
static int usbhsc_resume(struct device *dev)
^~~~~~~~~~~~~
drivers/usb/renesas_usbhs/common.c:844:12: error: 'usbhsc_suspend' defined but not used [-Werror=unused-function]
static int usbhsc_suspend(struct device *dev)
^~~~~~~~~~~~~~
Fixes: d54d334e75 ("usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ada211d03.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for legacy phys for rcar2 which hasn't been used with a
mainline kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy
usb-host.c platform init code"). Specifically, since that commit
usb_get_phy_dev() have always returned -ENODEV and consequently this
code has not been used.
Note that the legacy-phy API is still being used in gadget mode to bind
the peripheral controller.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the capability to support RZ/A1 SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds extcon notifier callback to set the mode of
host/peripheral by using extcon state (e.g phy-rcar-gen3-usb2) for
non-otg channel (e.g. R-Car D3).
[Fengguang Wu: fixed sparse warning]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: renesas_usbhs: usbhs_rcar3_notifier() can be static
Fixes: 3a7cce26122e ("usb: renesas_usbhs: add extcon notifier to set mode for non-otg channel")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usbhs_rcar3_power_and_pll_ctrl() will be used by non-otg channel
(e.g. R-Car D3) and the previous code has hardcoded as peripheral mode.
So, this patch sets the mode by using extcon state.
If the channel doesn't get any extcon devices, this driver's behavior
is the same as before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To cleanup the code, this patch adds a function to write the UGCTRL2
register.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch uses usbhs_pipe_clear_without_sequence() instead of
usbhsf_fifo_clear() because usbhsf_fifo_clear() may not clear the pipe
buffer completely. This patch also changes the clearing condition from
DMA only to both DMA and PIO.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds usbhs_pipe_clear_without_sequence() function.
The controller has the pipe buffer and the PIPEnCTR.ACLRM can clear
it completely. But, it's also clear the data sequence. So, the driver
needs to get the sequence before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
