We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_umem_release() is called after ib_uverbs_close() sets context->closing,
then a process can get stuck in a D state, because the code boils down to
if (down_write_trylock(&mm->mmap_sem))
down_write(&mm->mmap_sem);
which is obviously a stupid instant deadlock. Fix the code so that we
only try to take the lock once.
This bug was introduced in commit f7c6a7b5 ("IB/uverbs: Export
ib_umem_get()/ib_umem_release() to modules") which fortunately never
made it into a release, and was reported by Pete Wyckoff <pw@osc.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After i915 chip, GMCH has no AGP port. Origin bridge driver in device
table will try to access illegal regs like APBASE, APSIZE, etc. This
may cause problem.
So mark them as NULL in the table, we won't load if no IGD got detect
and bridge has no AGP port.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
fix module_param mistake in it821x
ahci: fix PORTS_IMPL override
kerneldoc fix in libata
libata: more NONCQ devices
pata_it821x: (partially) fix DMA in RAID mode
PATA: Add the MCP73/77 support to PATA driver
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix parameter name from ata_dev_reread_id() in libata-core.c for kerneldoc.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More for the NCQ blacklist. One hitachi and one raptor. Other
members of these families of drives are already on the list, so no
surprises.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code intended to check DMA status was checking DMA command register.
Moreover firmware seems to "forget" to set DMA capable bit for the
slave device (at least in RAID mode but without ITE RAID volumes) so
check device ID for DMA capable bit when deciding whether to use DMA
and remove DMA status check completely.
Thanks to Pavol Simo for the bugreport and testing the initial fix.
This change unfortunately still doesn't fix DMA in RAID mode (which
works fine with IDE it821x) but Alan is working on the missing pieces
(pata_it821x vs libata EH issues).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rx traffic needs to be halted when the MTU is changed
to avoid a potential chip hang.
Reset/restore MAC filters around a MTU change.
Also fix the pause frames high materwark setting.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check all lanes for link status on direct XAUI cards.
Don't assume that direct XAUI always uses XGMAC 1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix netpoll handler to work with line interrupt, msi and msi-x.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
eth_type_trans() now sets skb->dev.
References to skb->dev should happen after it is called.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The spinlock irq flags should be a unsigned long to properly support 64 bit
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I happened to notice that a system with an NVidia NIC using the
forcedeth driver won't wake-on-LAN if the interface was in promiscuous
mode when you power off. By experiment, it looks like
the hardware needs to have NvRegPacketFilterFlags set to
NVREG_PFF_ALWAYS|NVREG_PFF_MYADDR (i.e., receive unicast packets to my
address) in order for WoL to work.
Jeff Garzik writes: "NVIDIA says the patch looks OK." I didn't venture
to insert a signed-off-by line with his name on it, though.
Signed-off-by: Tim Mann <mann@vmware.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The recent iucv rework patches re-introduced some unnecessary inlines.
Remove them again.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spinlock initializer cleanup in netiucv.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net/iucv/iucv.c creates the requirement for
iucv_path_connect not to be called from tasklet context anymore.
An extra checking is added in case of a failing netiucv_tx
to fulfil this requirement for netiucv.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use ccw_device_get_id() to get a device number
instead of parsing the ccw device's bus id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Packets Length in qdio header is broken when using
EDDP on Layer2 devices. This leads to skb_under_panic on receiver
system when running on z/VM GuestLAN devices.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ipv6_regen_rndid in net/ipv6/addrconf.c makes use of "write_lock_bh"
for its inet6_dev->lock. It may run in softirq-context.
qeth makes use of "read_lock" for the same inet6_dev->lock.
To avoid a potential deadlock situation, qeth should make use of
"read_lock_bh" for its usages of inet6_dev->lock.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While first recovery continues, the card issues
a STARTLAN command itself. In this case qeth
schedules another recovery. This second
recovery is cancelled because of an already running first recovery.
Stop first recovery in case of 0xe080.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For real HiperSockets the EBCDIC-ASCII conversion is not necessary.
This is only needed for z/VM GuestLAN devices.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modify carrier state determination for 802.3ad mode to comply
with section 43.3.9 of IEEE 802.3, which requires that "Links that are
not successful candidates for aggregation (e.g., links that are attached
to other devices that cannot perform aggregation or links that have been
manually configured to be non-aggregatable) are enabled to operate as
individual IEEE 802.3 links."
Bug reported by Laurent Chavey <chavey@google.com>. This patch
is an updated version of his patch that changes the wording of
commentary and adds an update to the driver version.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch (based on a patch from Stephen Hemminger
<shemminger@linux-foundation.org>) removes use after free conditions in
the unregister path for the bonding master. Without this patch, an
operation of the form "echo -bond0 > /sys/class/net/bonding_masters"
would trigger a NULL pointer dereference in sysfs. I was not able to
induce the failure with the non-sysfs code path, but for consistency I
updated that code as well.
I also did some testing of the bonding /proc file being open
while the bond is being deleted, and didn't see any problems there.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It doesn't look like spidernet hardware can really checksum all protocols,
the code looks like it does IPV4 only. If so, it should use NETIF_F_IP_CSUM
instead of NETIF_F_HW_CSUM.
The driver doesn't need it's own get/set for ethtool tx csum, and it
should use the standard ethtool_op_get_link.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At some point, the transmit descriptor chain end interrupt (TXDCEINT)
was turned on. This is a mistake; and it damages small packet
transmit performance, as it results in a huge storm of interrupts.
Turn it off.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Although the previous patch resolved issues with hangs when the
RX ram full interrupt is encountered, there are still situations
where lots of RX ramfull interrupts arrive, resulting in a noisy
log in syslog. There is no need for this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The terminated RX ring will cause trouble during the RX ram full
conditions, leading to a hung driver, as the hardware can't find
the next descr. There is no real reason to terminate the RX ring;
it doesn't make the operation any smooother, and it does
require an extra sync. So don't do it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a rare deadlock that can occur when the kernel
is not able to empty out the RX ring quickly enough. Below follows
a detailed description of the bug and the fix.
As long as the OS can empty out the RX buffers at a rate faster than
the hardware can fill them, there is no problem. If, for some reason,
the OS fails to empty the RX ring fast enough, the hardware GDACTDPA
pointer will catch up to the head, notice the not-empty condition,
ad stop. However, RX packets may still continue arriving on the wire.
The spidernet chip can save some limited number of these in local RAM.
When this local ram fills up, the spider chip will issue an interrupt
indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit
will be set in GHIINT1STS). When te RX ram full condition occurs,
a certain bug/feature is triggered that has to be specially handled.
This section describes the special handling for this condition.
When the OS finally has a chance to run, it will empty out the RX ring.
In particular, it will clear the descriptor on which the hardware had
stopped. However, once the hardware has decided that a certain
descriptor is invalid, it will not restart at that descriptor; instead
it will restart at the next descr. This potentially will lead to a
deadlock condition, as the tail pointer will be pointing at this descr,
which, from the OS point of view, is empty; the OS will be waiting for
this descr to be filled. However, the hardware has skipped this descr,
and is filling the next descrs. Since the OS doesn't see this, there
is a potential deadlock, with the OS waiting for one descr to fill,
while the hardware is waiting for a differen set of descrs to become
empty.
A call to show_rx_chain() at this point indicates the nature of the
problem. A typical print when the network is hung shows the following:
net eth1: Spider RX RAM full, incoming packets might be discarded!
net eth1: Total number of descrs=256
net eth1: Chain tail located at descr=255
net eth1: Chain head is at 255
net eth1: HW curr desc (GDACTDPA) is at 0
net eth1: Have 1 descrs with stat=xa0800000
net eth1: HW next desc (GDACNEXTDA) is at 1
net eth1: Have 127 descrs with stat=x40800101
net eth1: Have 1 descrs with stat=x40800001
net eth1: Have 126 descrs with stat=x40800101
net eth1: Last 1 descrs with stat=xa0800000
Both the tail and head pointers are pointing at descr 255, which is
marked xa... which is "empty". Thus, from the OS point of view, there
is nothing to be done. In particular, there is the implicit assumption
that everything in front of the "empty" descr must surely also be empty,
as explained in the last section. The OS is waiting for descr 255 to
become non-empty, which, in this case, will never happen.
The HW pointer is at descr 0. This descr is marked 0x4.. or "full".
Since its already full, the hardware can do nothing more, and thus has
halted processing. Notice that descrs 0 through 254 are all marked
"full", while descr 254 and 255 are empty. (The "Last 1 descrs" is
descr 254, since tail was at 255.) Thus, the system is deadlocked,
and there can be no forward progress; the OS thinks there's nothing
to do, and the hardware has nowhere to put incoming data.
This bug/feature is worked around with the spider_net_resync_head_ptr()
routine. When the driver receives RX interrupts, but an examination
of the RX chain seems to show it is empty, then it is probable that
the hardware has skipped a descr or two (sometimes dozens under heavy
network conditions). The spider_net_resync_head_ptr() subroutine will
search the ring for the next full descr, and the driver will resume
operations there. Since this will leave "holes" in the ring, there
is also a spider_net_resync_tail_ptr() that will skip over such holes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Avoid kernel crash in mm/slab.c due to double-free of pointer.
If the ethernet interface is brought down while there is still
RX traffic in flight, the device shutdown routine can end up
trying to double-free an skb, leading to a crash in mm/slab.c
Avoid the double-free by nulling out the skb pointer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Only set client->iso_context if allocation was successful.
ieee1394: fix to ether1394_tx in ether1394.c
firewire: fix hang after card ejection
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure inline data segments don't cross a 64 byte boundary
IB/mlx4: Handle FW command interface rev 3
IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean()
IB/mlx4: Get rid of max_inline_data calculation
IB/mlx4: Handle new FW requirement for send request prefetching
IB/mlx4: Fix warning in rounding up queue sizes
IB/mlx4: Fix handling of wq->tail for send completions
This patch fixes an OOPS on cdev release for an fd where iso context
creation failed.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It's already annoying that they appear on x86 now -- that's for the 3button
emulation needed on x86 macs -- but at least don't make them default.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not directly related to x86, but I got tired of seeing these warnings on every
kconfig update when building on a non m68k box:
drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig
so it's always seen by Kconfig.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added members for volume number and real memory size to header information.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When compacting CQ entries, we need to set the correct value of the
ownership bit in case the value is different between the index we copy
the CQE from and the index we copy it to.
Found by Ronni Zimmerman of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The calculation of max_inline_data in set_kernel_sq_size() is bogus,
since it doesn't take into account the fact that inline segments may
not cross a 64-byte boundary, and hence multiple inline segments will
probably need to be used to post large inline sends.
We don't support inline sends for kernel QPs anyway, so there's no
point in doing this calculation anyway, since the field is just zeroed
out a little later. So just delete the bogus calculation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet. Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).
Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2. This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.
Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the routine acpi_ut_create_package_object(), if the
ACPI_ALLOCATE_ZEROED() fails then ACPI_FREE(package_desc) is called as
part of the cleanup. This should instead be
acpi_ut_remove_reference(package_desc) in order to remove the reference
acquired from acpi_ut_create_internal_object() [see the routine
acpi_ut_create_buffer_object() as an example of proper functionality].
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
if acpi_bus_get_device() returns NULL, print nothing
instead of "<NUL" in /proc/acpi/thermal_zone/*/trip_points
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
(As reported by linux@horizon.com)
Folding is done to minimize the theoretical possibility of systematic
weakness in the particular bits of the SHA1 hash output. The result of
this bug is that 16 out of 80 bits are un-folded. Without a major new
vulnerability being found in SHA1, this is harmless, but still worth
fixing.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: <linux@horizon.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If raid1/repair (which reads all block and fixes any differences it finds)
hits a read error, it doesn't reset the bio for writing before writing
correct data back, so the read error isn't fixed, and the device probably
gets a zero-length write which it might complain about.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ When resyncing a degraded raid10 which has more than 2 copies of each block,
garbage can get synced on top of good data.
2/ We round the wrong way in part of the device size calculation, which
can cause confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix section error (allyesconfig). The exit function is called from init,
so functions that are called by the exit function cannot be marked __exit.
WARNING: drivers/built-in.o(.text+0xe5bc6): Section mismatch: reference to .exit.
text: (between 'toshiba_acpi_exit' and 'hci_raw')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore tty locked ioctl handler which was replaced with
an unlocked ioctl handler in hung_up_tty_fops by the patch:
commit e10cc1df1d
Author: Paul Fulghum <paulkf@microgate.com>
Date: Thu May 10 22:22:50 2007 -0700
tty: add compat_ioctl
This was reported in:
[Bug 8473] New: Oops: 0010 [1] SMP
The bug is caused by switching to hung_up_tty_fops in do_tty_hangup. An
ioctl call can be waiting on BLK after testing for existence of the locked
ioctl handler in the normal tty fops, but before calling the locked ioctl
handler. If a hangup occurs at that point, the locked ioctl fop is NULL
and an oops occurs.
(akpm: we can remove my debugging code from do_ioctl() now, but it'll be OK to
do that for 2.6.23)
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9b01bd5b28 introduced a
compat_ioctl handler for RADEON_SETPARAM, the sole purpose of which was
to handle the fact that on i386, alignof(uint64_t)==4.
Unfortunately, this handler was installed for _all_ 64-bit
architectures, instead of only x86_64 and ia64. And thus it breaks
32-bit compatibility on every other arch, where 64-bit integers are
aligned to 8 bytes in 32-bit mode just the same as in 64-bit mode.
Arnd has a cunning plan to use 'compat_u64' with appropriate alignment
attributes according to the 32-bit ABI, but for now let's just make the
compat_radeon_cp_setparam routine entirely disappear on 64-bit machines
whose 32-bit compat support isn't for i386. It would be a no-op with
compat_u64 anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a problem that occurs when packets cannot be sent across
the ieee1394 bus and we return NETDEV_TX_BUSY in the net driver "hard start
xmit" routine ether1394_tx. When we return NETDEV_TX_BUSY the stack will
call ether1394_tx again with the same skb. So we need to restore the header
to look like it did before we munged it for xmit over ieee1394.
[Stefan Richter: changed whitespace, deleted a local variable]
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
generic_ide_resume() should check if dev->driver is not NULL before applying
to_ide_driver() to it. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin SMC91X ethernet supporting driver: SMC91C111 LEDs are note drived in the kernel like in uboot
Blackfin SPI driver: fix bug SPI DMA incomplete transmission
Blackfin SPI driver: tweak spi cleanup function to match newer kernel changes
Blackfin RTC drivers: update MAINTAINERS information
Blackfin serial driver: decouple PARODD and CMSPAR checking from PARENB
Blackfin serial driver: actually implement the break_ctl() function
Blackfin serial driver: ignore framing and parity errors
Blackfin serial driver: hook up our UARTs STP bit with userspaces CMSPAR
Blackfin arch: move HI/LO macros into blackfin.h and punt the rest of macros.h as it includes VDSP macros we never use
Blackfin arch: redo our linker script a bit
Blackfin arch: make sure we initialize our L1 Data B section properly based on the linked kernel
Blackfin arch: fix bug can not wakeup from sleep via push buttons
Blackfin arch: add support for Alon Bar-Lev's dynamic kernel command-line
Blackfin arch: add missing gpio.h header to fix compiling in some pm configurations
Blackfin arch: As Mike pointed out range goes form m..MAX_BLACKFIN_GPIO -1
Blackfin arch: fix spelling typo in output
Blackfin arch: try to split up functions like this into smaller units according to LKML review
Blackfin arch: add proper ENDPROC()
Blackfin arch: move more of our startup code to .init so it can be freed once we are up and running
Blackfin arch: unify differences between our diff head.S files -- no functional changes
...
The lazy fpu changes did not take into account that some vmexit handlers
can sleep. Move loading the guest state into the inner loop so that it
can be reloaded if necessary, and move loading the host state into
vmx_vcpu_put() so it can be performed whenever we relinquish the vcpu.
Signed-off-by: Avi Kivity <avi@qumranet.com>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: fix radeon setparam on 32/64 bit systems.
drm/i915: Add support for the G33, Q33, and Q35 chipsets.
i915: add new pciids for 945GME, 965GME/GLE
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (30 commits)
[PARISC] remove global_ack_eiem
[PARISC] Fix kernel panic in check_ivt
[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls
[PARISC] be more defensive in process.c::get_wchan
[PARISC] fix "reduce size of task_struct on 64-bit machines" fallout
[PARISC] fix null ptr deref in unwind.c
[PARISC] fix trivial spelling nit in asm/linkage.h
[PARISC] remove remnants of parisc-specific softirq code
[PARISC] fix section mismatch in smp.c
[PARISC] fix "ENTRY" macro redefinition
[PARISC] Wire up utimensat/signalfd/timerfd/eventfd syscalls
[PARISC] fix section mismatch in superio serial drivers
[PARISC] fix section mismatch in parisc eisa driver
[PARISC] fix section mismatches in arch/parisc/kernel
[PARISC] fix section mismatch in ccio-dma
[PARISC] fix section mismatch in parisc STI video drivers
[PARISC] fix section mismatch in parport_gsc
[PARISC] fix lasi_82596 build
[PARISC] Build fixes for power.c
[PARISC] kobject is embedded in subsys, not kset
...
This patch trys to fix device probe in two cases. First we should
correctly detect device if integrated graphics device is not enabled
or exists, like an add-in card is plugged. Second on some type of intel
GMCH, it might have multiple graphic chip models, like 945GME case, so
we should be sure the detect works through the whole table.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6] addrconf: Fix IPv6 on tuntap tunnels
[TCP]: Add missing break to TCP option parsing code
[SCTP] Don't disable PMTU discovery when mtu is small
[SCTP] Flag a pmtu change request
[SCTP] Update pmtu handling to be similar to tcp
[SCTP] Fix leak in sctp_getsockopt_local_addrs when copy_to_user fails
[SCTP]: Allow unspecified port in sctp_bindx()
[SCTP]: Correctly set daddr for IPv6 sockets during peeloff
[TCP]: Set initial_ssthresh default to zero in Cubic and BIC.
[TCP]: Fix left_out setting during FRTO
[TCP]: Disable TSO if MD5SIG is enabled.
[PPP_MPPE]: Fix "osize too small" check.
[PATCH] mac80211: Don't stop tx queue on master device while scanning.
[PATCH] mac80211: fix debugfs tx power reduction output
[PATCH] cfg80211: fix signed macaddress in sysfs
[IrDA]: f-timer reloading when sending rejected frames.
[IrDA]: Fix Rx/Tx path race.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: move input-polldev to drivers/input
Input: i8042 - add ULI EV4873 to noloop list
Input: i8042 - add ASUS P65UP5 to the noloop list
Input: usbtouchscreen - fix fallout caused by move from drivers/usb
esp_reset_cleanup() does everything necessary except clear
the flag, so we never exit resetting state.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ignoring OMAP_MMC_STAT_CARD_ERR, treating it as if the command
completed correctly.
Signed-off-by: Ragner Magalhaes <ragner.magalhaes@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
To work around deficiences in Kconfig that allows to "select"
a symbol without automatically selecting all dependencies for
that symbol move input-polldev from drivers/input/misc to
drivers/input thus removing extra dependency on CONFIG_INPUT_MISC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since Myri-10G boards may also run in Myrinet mode instead of Ethernet,
add a message when we detect that the link partner is not running in the
right mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Limit the number of recoveries from a NIC hw watchdog reset to 1 by default.
It enables detection of defective NICs immediately since these memory parity
errors are expected to happen very rarely (less than once per century*NIC).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit d52df4a35a.
This patch attempted to fix e100 for non-cache coherent memory
architectures by using the cb style code that eepro100 had and using
the EL and s bits from the RFD list. Unfortunately the hardware
doesn't work exactly like this and therefore this patch actually
breaks e100. Reverting the change brings it back to the previously
known good state for 2.6.22. The pending rewrite in progress to this
code can then be safely merged later.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent mppe_decompress() from generating "osize too small" errors when
checking for output buffer size. When receiving a packet of mru size the
output buffer for decrypted data is 1 byte too small since
mppe_decompress() tries to account for possible PFC, however later in code
it is assumed no PFC.
Adjusting the check prevented these errors from occurring.
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With firmware 5.220.11.p5, this allows to specify the anycast addresses the
device will listen to.
The anycast address range is C0:27:C0:27:C0:XX where XX goes from 00 to 1F (or
0 to 31 in dec). The value to write on anycast_mask will specify which
addresses the device listens to. Bits in a 32 bit int are numbered from 0
(least significative bit) to 31. A specific address ending in YY will be
listened to if bit YY in the value is set to one.
Examples:
0x00000000 : do not listen to any anycast address
0xFFFFFFFF : listen to every anycast address from :00 to :1F
0x00000013 : listen to anycast addresses :00, :01 and :04
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids channel mismatch between driver and firmware in case we change
channel while associated to an AP.
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing max(1, foo) where foo is u32 generates a warning, because 1 is a
signed constant. Fix this by using 1U instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cast the increment added to wq->tail when send completions are
processed to u16 to avoid using wrong values caused by standard
integer promotions.
The same bug was fixed in libmlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The box does not implement AUX LOOP command properly and so we
can't test for AUX IRQ delivery so blacklist it via DMI and
assume that AUX port is present.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This board does not raise AUX IRQ in response to AUX LOOP command
which interferes with our test for proper AUX IRQ wiring. Put it
in the blacklist and assume mouse is present.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
During the move from drivers/usb/input into drivers/input/touchscreen
Kconfig variables were shuffled a bit to use a new namespace
(CONFIG_TOUCHSCREEN) while usbtouchscreen was still using old ones.
Also noticed by Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure RQ allocation is always valid
RDMA/cma: Fix initialization of next_port
IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
mlx4_core: Don't set MTT address in dMPT entries with PA set
mlx4_core: Check firmware command interface revision
IB/mthca, mlx4_core: Fix typo in comment
mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
mlx4_core: Initialize ctx_list and ctx_lock earlier
mlx4_core: Fix CQ context layout
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] intel_agp: Add support for G33, Q33 and Q35 chipsets
[AGPGART] intel_agp: add support for 945GME
[AGPGART] intel_agp: add support for 965GME/GLE
[AGPGART] intel_agp: use table for device probe
[AGPGART] intel_agp: cleanup intel private data
* 'linus-plus-plus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: limit post SRST nsect/lbal wait to ~100ms
libata: force PIO on IOMEGA ZIP 250 ATAPI
libata passthru: update cached device paramters
libata passthru: always enforce correct DEV bit
libata passthru: map UDMA protocols
libata passthru: support PIO multi commands
libata passthru: update protocol numbers
libata: Correct abuse of language
libata-core/sff: Fix multiple assumptions about DMA
ahci: Add MCP73/MCP77 support to AHCI driver
libata: fix hw_sata_spd_limit initialization
libata: print device model and firmware revision for ATAPI devices
libata: fix probe time irq printouts
libata: disable NCQ for HITACHI HTS541680J9SA00/SB21C7EP
remove unused variable in pata_isapnp
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: Add the MCP73/77 support to PATA driver
Add the PATA controller device ID to pci_ids.h for MCP73/MCP77.
hpt366: disallow Ultra133 for HPT374
ide: generic IDE PCI driver, add another device exception
ide: HPA detect from resume
it821x: RAID mode fixes
serverworks: fix CSB6 tuning logic
serverworks: remove crappy code
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: don't call switch on old cards
mmc: fix broken if clause
au1xmmc: Replace C code with call to ARRAY_SIZE() macro.
mmc-atmel: remove linux/mmc/protocol.h dependencies
Kill mixed case function names from scan.c/scan.h.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace WLAN_802_11_SSID with direct 'ssid' and 'ssid_len' members
like ieee80211. In the process, remove private libertas_escape_essid
and depend on the ieee80211 implementation of escape_essid instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Byte-swapping length fields and then passing them to memcpy() considered
harmful.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we finally get connectivity. For a while, before something else dies...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now it at least manages to load the firmware.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate wireless handlers of mshX and ethX. ethX remains as before.
For mshX, it has been disabled set/get essid, wap and set mode. Get mode always
returns "Repeater" and by now we use the Nickname to show if the mesh is active
("Mesh") or not (empty). The rest remains as before.
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some wording and blinding table command options, clarify argument list for
fwt_add and fwt_list, simplify fwt_list_route
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix WPA so it works up through the supplicant 4-Way handshake process.
Doesn't successfully pass traffic yet; may be problems installing
the GTK to the firmware.
- RSN needs to be enabled before the association command is sent
- Use keys from the association request not the adapter structure
- cmd_act_mac_strict_protection_enable != IW_AUTH_DROP_UNENCRYPTED
- Fix network filtering logic in is_network_compatible() WPA helpers
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Any time the driver gets new scan results, even from partial scans,
it should send the scan event to userspace.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously if a fixed channel was specified along with an SSID,
the channel request would be ignored during the association
process. Instead, when searching for an adhoc or infrastructure
network to join, allow filtering results based on channel so
that the driver doesn't pick a BSS on a different channel than
requested.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inadvertently removed on a previous commit; causes the first
adhoc start to fail if a channel has not been set or no
other association has been made.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update signal quality before the locked scan result translation loop,
because calling libertas_prepare_and_send_command() with the
'waitforrsp' option grabs adapter->lock in the command return processing,
leading to the deadlock.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the leave debug print gets triggered when necessary.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
adapter->lock should released after unlocking adapter->driver_lock to
balance the order in which they were locked at the top of the function.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS to associate with (in either Infrastructure or IBSS join
operations) is now stored in _one_ place in the association request (the
bss member), not two places as before (pattemptedbss and
curbssparams->bssdescriptor).
Association requests are passed to the necessary association functions
to (a) give them access to the bss member and (b) ensure that
association/join/start setup uses settings from the request, not the
current adapter settings (which may not be valid for the requested
settings).
Because the 'bss' member of the association request is used now, the
command return functions from associate and adhoc join/start need access
to the in-progress association request to update curbssparams when
everything is done. The association worker moves the request from
pending to in-progress for the duration of the association attempt.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle channel changes through the deferred association framework
rather than directly. Fixes errors when setting channels along
with other parameters like mode and SSID.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry_safe, to protect against list_del().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not clear the scan list except under specific conditions, such as
when (a) user-requested, or (b) joining/starting an adhoc network.
Furthermore, only clear entries which match the SSID or BSSID of the
request, not the whole scan list.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- use a linked list for scan results
- age scan results
- pass bss_descriptors around instead of indexes into the scan table
- lock access to the scan results
- stop returning EAGAIN from SIOCGIWSCAN handler
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updated commands fwt_add and fwt_list, bt_list.
New commands: bt_get_invert, bt_set_invert, to invert the blinding table,
i.e., receive only frames from nodes listed in the BT.
This patch needs/is needed for firmware 5.220.9.p11.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch along with the previous commands update one, is necessary for
mesh and fwt ioctls to work properly with firmware version 5.220.10.p0
and later.
Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas_activate_card() doesn't create the netdev, and shouldn't
free it on error. The caller of libertas_activate_card() is
responsible for cleaning up errors from libertas_add_card(),
not libertas_activate_card().
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Start to normalize bss_descriptor with ieee80211_network so we can
eventually replace bss_descriptor more easily.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move usage of SET_NETDEV_DEV into common code since it has nothing
to do with bus-specific devices. Also fixes a bug where the mesh
device was getting SET_NETDEV_DEV called after register_netdevice,
resulting in no 'device' link in /sys/class/net/mshX/.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed kernel oops on module/card removal (using dongles)
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually, this patch removev wlan_dev_t totally and puts the used variables
of it directly into wlan_private. That reduces one level of indirection and
looks a little bit simpler. It's now "priv->card" and not
"priv->wlan_dev.card" and "priv->dev" instead of "priv->wlan_dev.netdev"
Changed two occurences of "((wlan_private *) dev->priv)->wlan_dev.netdev"
into "dev", because I didn't see the point in doing pointer-ping-pong.
The variables "ioport", "upld_rcv" and "upld_type" where unused. They have
been removed.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, it's "libertas" by default, but that is overwritten in
if_usb.c/if_bootcmd.c and in if_cs.c.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, we had a fixed array of 5 elements where we remembered all
initialized devices. This has been changed to use a "struct list_head"
organization, which is IMHO cleaner.
Also renamed usb_cardp to cardp, as in the reset of the code.
Renamed reset_device() to if_usb_reset_device() like many other functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* add CONFIG_LIBERTAS to Kconfig
* remove global variable libertas_fw_name, the USB module might want to
use a different default FW name than the CF module, so libertas_fw_name
is now local to if_usb.c
* exported some symbols as GPL
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also removes some useless "extern" declarations from function declaration.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This functions makes all libertas_sbi_XXX functions static to the
if_usb.c file and renames them to if_usb_XXXX(). The get called from
other places of the source code via priv->hw_XXXX().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch wakes up the mesh device *instead* of the wlan device
when coming out of scan. We need to wake up both of them.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added transmission failures to mesh statistics.
Removed whitespace before newlines.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements proper transmission flow control on mshX.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split wlan_add_card() into a part that just setups kernel parameters and
into the function libertas_activate_card(), which will implizitly use
hardware functions by the started thread.
This allows us later to do something like this:
priv = libertas_add_card();
priv->hw_command_to_host = if_usb_command_to_host;
priv->hw_xxxx = if_usb_xxxx;
priv->hw_yyyy = if_usb_yyyy;
wlan_activate_card()
and of course the CF driver can set it's own functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reset_device() logic is only needed for USB devices, not for CF
devices.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* a newline was missing
* changed %32s to '%s', no need to right justify the ESSID
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not really needed, because we can call wlan_remove_card() with
wlan_private* anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD
Also fixed a missing ":" in lbs_deb_enter()
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.
Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For me it looks cleaner, because it removes one level of indirection.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEV_NAME_LEN is already defined in defs.h and that is sufficient.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove filename from debug output because it's way too long.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renames wlan_association_worker into libertas_association_worker
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.
This gives time to the firmware so it can go back to the association
channel and keep the connection alive.
Fixes http://dev.laptop.org/ticket/841
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
as the termios info does not stipulate that the former are dependent on the latter
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
if we get a break signal, we want to ignore framing and parity errors
because those will always be set (by nature of the signal)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
After SRST, libata used to wait for nsect/lbal to be set to 1/1 for
the slave device. However, some ATAPI devices don't set nsect/lbal
after SRST and the wait itself isn't too useful as we're gonna wait
for !BSY right after that anyway.
Before reset-seq update, nsect/lbal wait failure used to be ignored
and caused 30sec delay during detection. After reset-seq, all
timeouts are considered error conditions making libata fail to detect
such ATAPI devices.
This patch limits nsect/lbal wait to around 100ms. This should give
acceptable behavior to such ATAPI devices while not disturbing the
heavily used code path too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IOMEGA ZIP 250 ATAPI claims MWDMA0 support but fails SETXFERMODE if
asked to configure itself to MWDMA0. Force PIO.
This fixes bugzilla bug#8497.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Calvin Walton <calvin.walton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These require that the status page be referenced by a pointer in GTT, rather
than phsyical memory. So, we have the X Server allocate that memory and tell
us the address, instead.
Signed-off-by: Dave Airlie <airlied@linux.ie>
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hw_sata_spd_limit used to be incorrectly initialized to zero instead
of UINT_MAX if SPD is zero in SControl register. This breaks PHY
speed down. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For ATA/CFA devices, libata prints out the device model and firmware revision.
Do the same for ATAPI devices.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers don't seem to fill out the host->irq field, resulting in the
wrong (no) irq being reported at probe time. For example, sil24 on my system:
ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
Since they're allocated and set up in ata_host_activate(), just save
them away there.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch has removed unused variable in pata_ispnp.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace invisible character with a space.
The diff looks like this on my terminal:
- <A0>Choose this option if you're using a host-to-host cable
- <A0>with one of these chips.
+ Choose this option if you're using a host-to-host cable
+ with one of these chips.
Reported by: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for configuring RGMII-ID (RGMII with internal delay) mode on the
88e1111 and 88e1145. Ucc_geth on MPC8360EMDS(the main user of ucc_geth)
is broken after changed to use phylib. It is fixed by adding this
internal delay.
Also renamed 88e1111s -> 88e1111 (no references to an 88e1111s part were
found), and fixed some whitespace.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a possible kernel panic due to not checking the vlan group
when processing received VLAN packets and a malfunction in VLAN/hypervisor
registration.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Add NETXEN prefixes to macros to clean them up.
This is a cleanup patch which adds NETXEN prefix to some stand
alone macro names.
These posed compile errors when NetXen driver was backported to 2.6.9
on PPC architecture as macros like USER_START are defined in file
arch/ppc64/mm/hash_utils.c
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Acked-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
