As only a subset of primary planes are FBC capable there's no need
to waste fences on all of them. So let's skip the fence if the plane
isn't even fbc capable.
In the future we might extend this to skip the fence even for FBC
capable planes if the crtc and/or plane state isn't suitable
for FBC.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221160235.11134-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently we pin a fence on every plane doing tiled scanout. The
number of planes we have available is fast apporaching the number
of fences so we really should stop wasting them. Only FBC needs
the fence on gen4+, so let's use fences only for the primary planes
on those platforms.
v2: drop the tiling check from plane_uses_fence() as the obj is
NULL during initial_plane_config() and we don't rally need the
check since i915_vma_pin_fence() does the check anyway
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221184807.577-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Some panels support limited range output (16-235) compared
to full range RGB values (0-255). Also userspace can control
the RGB range using "Broadcast RGB" property. Currently the
code to handle full range to limited range is broken. This
patch fixes the same by properly scaling down all the full
range co-efficients with limited range scaling factor.
v2: Fixed Ville's review comments.
v3: Changed input to const and used correct data types as
suggested by Ville
v4: Fixed some missing data type corrections.
Signed-off-by: Johnson Lin <johnson.lin@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1517327489-26128-1-git-send-email-uma.shankar@intel.com
It turns out that HSW has a register that tells us how many EUs are
disabled per half-slice (roughly a similar notion to subslice). We
didn't read those registers so far as most userspace drivers didn't
need those values prior to Gen8, but an internal library would like to
have access to this.
Since we already have the getparam interface, there is no harm in
exposing this.
v2: Rename bits value (Joonas)
v3: s/GEM_BUG_ON/MISSING_CASE/ (Joonas)
v4: s/GEM_BUG_ON/MISSING_CASE/ again... (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221204902.23084-1-lionel.g.landwerlin@intel.com
Show GEN11 specific interrupt registers in debugfs
v2: Update for POR changes. (Daniele Ceraolo Spurio)
v3: get runtime pm ref. unify common parts with gen8 (Daniele)
Cc: Ceraolo Spurio, Daniele <daniele.ceraolospurio@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220153755.13509-2-mika.kuoppala@linux.intel.com
This is the current PCI ID list in our documentation.
Let's leave the _gt#_ part out for now since our current documentation
is not 100% clear and we don't need this info now anyway.
v2: Use the new ICL_11 naming (Kelvin Gardiner).
v3: Latest IDs as per BSpec (Oscar).
v4: Make it compile (Paulo).
v5: Remove comments (Lucas).
v6: Multile rebases (Paulo).
v7: Rebase (Mika)
Reviewed-by: Anuj Phogat <anuj.phogat@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220153755.13509-1-mika.kuoppala@linux.intel.com
Print out the current request/context before doing the GEM_BUG_ON, so
that we can inspect the values in the ftrace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221152301.9178-1-chris@chris-wilson.co.uk
Load an empty ringbuffer for preemption, ignoring the lite-restore
workaround as we know the preempt context is always idle before preemption.
Note that after some digging by Michal Winiarski, we found that
RING_HEAD is no longer being updated (due to inhibiting context save
restore) so this patch is already in effect!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221133236.29402-1-chris@chris-wilson.co.uk
We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)
In short, the spatch:
@@
@@
- struct drm_i915_gem_request
+ struct i915_request
A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Noticed while reading some unrelated patches. Unfortunately Imre's
patch to add our early/late hooks predated the device_link
infrastructure by 2 years.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220132017.30719-1-daniel.vetter@ffwll.ch
Commit fe49789fab ("drm/i915: Deconstruct execute fence") re-arranged
the code and moved the i915_gem_request_execute tracepoint to before the
global seqno is assigned to the request.
We need to move the tracepoint a bit later so this information is once
again available.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: fe49789fab ("drm/i915: Deconstruct execute fence")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220104742.565-1-tvrtko.ursulin@linux.intel.com
Rather than trusting the cached value of plane_state->vma->fence to
imply whether the plane_state itself holds a reference on the
framebuffer's fence, use the information provided in the
plane_state->flags (PLANE_HAS_FENCE). Note that we still assume that FBC
is entirely bounded by the plane_state active life span; it's not clear
if that is a safe assumption.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-4-chris@chris-wilson.co.uk
Use the information about the fence state from the time of pinning to
determine if the fbdev writes are going through a fence. This avoids any
confusion in cases where the fence may appear or disappear unconnected
to the use by fbdev.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-3-chris@chris-wilson.co.uk
We cannot simply use !view as shorthand for all normal GGTT views as a
few callers will always populate a i915_ggtt_view struct and set the
type to NORMAL instead. So check for (!view || view->type == NORMAL)
inside i915_gem_object_ggtt_pin().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134208.24988-1-chris@chris-wilson.co.uk
i965 and g4x still have the pipe select bits in the plane control
registers, they're just hardcoded to select a specific pipe. However
plane C on i965 can still move between the pipes, thus we should
program the pipe select bits on i965 if we want to expose plane C
some day.
Since there is no harm in programming the bits on any plane on
i965/g4x let's just always set them. This will also make our
pre-computed register value match what the hardware register
would read, should we want to cross check the two.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-2-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
G4x cursor control registers still allow us to write to the pipe select
bits even though cursors are supposed to be fixed to a specific pipe.
Bspec tells us that we should only ever write 0 to these bits. Let's
follow that recommendation. On ilk+ the bits become hardwired to 0.
Also looks like ICL repurposes these bits for some other use, so
we had better stop setting them to bogus values there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Add some compile time assrts to the frontbuffer tracking to make sure
that we have enough bits per pipe to cover all the planes, and that we
have enough total bits to cover all the planes across all pipes.
We'll ignore any potential clash between the overlay bit and the
plane bits because that will allow us to keep using a total of 32
bits for the foreseeable future.
While at it change the macros to use BIT() and GENMASK(). The latter
gets rid of the hardcoded 0xff and thus means we can change the
number of bits per pipe by just changing
INTEL_FRONTBUFFER_BITS_PER_PIPE.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124183642.32549-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
During igt, we frequently call into the driver to reset both HW and
driver state (idling the device, waiting for it to become idle and
freeing off old objects) to ensure that we start each test/subtest/pass
from known state. This process incurs an RCU barrier or two to ensure
that any such pending frees are indeed flushed before we return.
However, unconditionally waiting on the RCU barrier adds needless delay
to many callers, which adds up to several seconds when repeated thousands
of times. We can skip the rcu_barrier() if by tracking how many outstanding
frees we have, we know there are none.
The same path is used along suspend, where we may be able to save the
unconditional RCU barrier.
To put it into perspective with a completely meaningless
microbenchmark, igt/gem_sync/idle is improved from 50ms to 30us on bdw.
v2: Remove the extra synchronize_rcu() inside i915_drop_caches_set()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219220631.25001-1-chris@chris-wilson.co.uk
clang spots
drivers/gpu/drm/i915/intel_pm.c:4655:6: warning: variable 'trans_min' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (INTEL_GEN(dev_priv) >= 10)
but fortunately for us we skip the function unless on a gen10+ device.
However, to keep the function generic in case we do want to re-enable it
for gen9 again, initialise trans_min to 0.
References: ca47667f52 ("drm/i915/gen10: Calculate and enable transition WM")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115105036.1094-3-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If we fail to unbind the vma (due to a signal on an active buffer that
needs to be moved for the next execbuf), then we need to clear the
persistent tracking state we setup for this execbuf.
Fixes: c7c6e46f91 ("drm/i915: Convert execbuf to use struct-of-array packing for critical fields")
Testcase: igt/gem_fenced_exec_thrash/no-spare-fences-busy*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219140144.24004-1-chris@chris-wilson.co.uk
The compiler is not automatically caching the i915->regs address inside
a register and emitting a load for every mmio access. For simple
functions like gen8_gt_irq_handler that are already using the raw
accessors, we can open-code them for substantial savings:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-83 (-83)
Function old new delta
gen8_gt_irq_handler 290 266 -24
gen8_gt_irq_ack 181 122 -59
Total: Before=954637, After=954554, chg -0.01%
v2: Add raw_reg_read/raw_reg_write.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219100926.16554-1-chris@chris-wilson.co.uk
Keep the master iir and use it to reduce the number of reads and writes
to the GT iir array, i.e. only the bits marked as set by the master iir
are valid inside GT iir array and will be handled during the interrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215073713.26985-1-chris@chris-wilson.co.uk
The in-lined comments for channel.port doesn't follow the syntax
described at kernel-doc document, causing the following warning:
$ ./scripts/kernel-doc -none drivers/gpu/drm/i915/intel_dpio_phy.c
drivers/gpu/drm/i915/intel_dpio_phy.c:154: warning: Function parameter or member 'channel.port' not described in 'bxt_ddi_phy_info'
While the best would be for the Kernel to deduce that from the
context, supporting it is not trivial. So, let's just stick with
the existing syntax.
[Jani: depends on "scripts: kernel-doc: support in-line comments on
nested structs/unions" to actually fix the warning.]
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9ba9ac773f4f9e60770bd9169b0e46ac974d858a.1518788761.git.mchehab@s-opensource.com
Hitting the failure path through check_digital_port_conflicts triggers:
================================================
WARNING: lock held when returning to user space!
4.16.0-rc1-CI-kasan_1+ #1 Tainted: G W
------------------------------------------------
kms_3d/1439 is leaving the kernel with locks still held!
1 lock held by kms_3d/1439:
#0: (drm_connector_list_iter){.+.+}, at: [<000000003745d183>] intel_atomic_check+0x1d9d/0x3ff0 [i915]
Rearrange the code to have a single exit path through the unlock.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215091425.42364-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We can't assert that the execlists are active before we set the flag. So
perform the assert after we are expected to have marked the execlists
active.
Fixes: 339ccd35b4 ("drm/i915: Assert that we always complete a submission to guc/execlists")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216153210.30551-1-chris@chris-wilson.co.uk
The continual resubmission model for execlists (and emulated over guc)
requires that we keep feeding requests into the HW in order to generate
more CS interrupts to drain the rest of the queue. Add a couple of
asserts to ensure that we don't skip a cycle and come to a grinding
halt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215162553.23348-1-chris@chris-wilson.co.uk
i915 is the only driver using those fields in the drm_gem_object
structure, so they only waste memory for all other drivers.
Move the fields into drm_i915_gem_object instead and patch the i915 code
with the following sed commands:
sed -i "s/obj->base.read_domains/obj->read_domains/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c
sed -i "s/obj->base.write_domain/obj->write_domain/g" drivers/gpu/drm/i915/*.c drivers/gpu/drm/i915/*/*.c
Change is only compile tested.
v2: move fields around as suggested by Chris.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216124338.9087-1-christian.koenig@amd.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Register Address for CNL_PORT_DW5_LN0_D is 0x162E54, but current code is
defining it as 0x162ED4. Similarly for CNL_PORT_DW7_LN0_D register address
is defined 0x162EDC instead of 0x162E5C, fix it.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage swing sequences.")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215095643.3844-2-mahesh1.kumar@intel.com
The frame counter may have got reset between disabling and enabling vblank
interrupts due to DMC putting the hardware to DC5/6 states if PSR was
active. The frame counter could also have stalled if PSR was active in case
there was no DMC. The frame counter resetting has a user visible impact
of screen freezes.
Make use of drm_vblank_restore() to compute missed vblanks for the duration
in which vblank interrupts were disabled and update the vblank counter with
this value as diff. There's no need to check if PSR was actually active in
the interrupt disabled duration, so simplify the check to a feature check.
Enabling vblank interrupts wakes up the hardware from DC5/6 and prevents it
from going back again as long as the there are pending interrupts. So, we
don't have to explicity disallow DC5/6 after enabling vblank interrupts to
keep the counter running.
This change is not applicable to CHV, as enabling interrupts does not
prevent the hardware from activating PSR.
v2: Added comments(Rodrigo) and rewrote commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-10-dhinakaran.pandiyan@intel.com
The HW frame counter can get reset if device enters a low power state after
vblank interrupts were disabled. This messes up any following vblank count
update as a negative diff (huge unsigned diff) is calculated from the HW
frame counter change. We cannot ignore negative diffs altogther as there
could be legitimate wrap arounds. So, allow drivers to update vblank->count
with missed vblanks for the time interrupts were disabled. This is similar
to _crtc_vblank_on() except that vblanks interrupts are not enabled at the
end as this function is expected to be called from the driver
_enable_vblank() vfunc.
v2: drm_crtc_vblank_restore should take crtc as arg. (Chris)
Add docs and sprinkle some asserts.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-9-dhinakaran.pandiyan@intel.com
Updating vblank counts requires register reads and these reads may not
return meaningful values if the device was in a low power state after
vblank interrupts were last disabled. So, update the count only if vblank
interrupts are enabled. Secondly, this means the registers should be read
before disabling vblank interrupts.
v2: Don't check vblank->enabled outside it's lock (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-8-dhinakaran.pandiyan@intel.com
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64.
The flip ioctl receives a 32-bit target sequence from user space and is
compared against the current sequence from drm_crtc_vblank_count(). So,
typecast return from drm_crtc_vblank_count() explicitly to add clarity.
__drm_crtcs_state.last_vblank_count however only ever stores the value from
drm_crtc_vblank_count() and can be upgraded to u64.
Cc: Keith Packard <keithp@keithp.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-7-dhinakaran.pandiyan@intel.com
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this
down to u32 either fixes a potential problem or serves to add clarity in
case the implicit typecasting was already correct.
Cc: Keith Packard <keithp@keithp.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-6-dhinakaran.pandiyan@intel.com
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this down
to u32 either fixes a potential problem or serves to add clarity in case
the implicit typecasting was already correct.
Cc: Keith Packard <keithp@keithp.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-5-dhinakaran.pandiyan@intel.com
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this down
to u32 either fixes a potential problem or serves to add clarity in case
the typecasting was implicitly done.
Cc: Keith Packard <keithp@keithp.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com> for both this patch
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-4-dhinakaran.pandiyan@intel.com
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64, store all the bits
without truncating. There is no need to type cast this value down to
32-bits.
Cc: Keith Packard <keithp@keithp.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-3-dhinakaran.pandiyan@intel.com
drm_vblank_count() has an u32 type returning what is a 64-bit vblank count.
The effect of this is when drm_wait_vblank_ioctl() tries to widen the user
space requested vblank sequence using this clipped 32-bit count(when the
value is >= 2^32) as reference, the requested sequence remains a 32-bit
value and gets queued like that. However, the code that checks if the
requested sequence has passed compares this against the 64-bit vblank
count.
With drm_vblank_count() returning all bits of the vblank count, update
drm_crtc_accurate_vblank_count() so that drm_crtc_arm_vblank_event() queues
the correct sequence. Otherwise, this leads to prolonged waits for a vblank
sequence when the current count is >=2^32.
Finally, fix drm_wait_one_vblank() too.
v2: Commit message fix (Keith)
Squash commits (Rodrigo)
Fixes: 570e86963a ("drm: Widen vblank count to 64-bits [v3]")
Cc: Keith Packard <keithp@keithp.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-1-dhinakaran.pandiyan@intel.com
Fix inconsistent IS_ERR and PTR_ERR in shrink_boom.
The proper pointer to use is _explode_ instead of _purge_.
This issue was detected with the help of Coccinelle.
Fixes: fe215c8bc4 ("drm/i915/selftests: add missing gtt shrinker test")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214211234.GA22341@embeddedgus
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than deriving the platform_mask from the
intel_device_static_info->platform at runtime, pre-fill it in the static
data.
v2: Undefine macros at end of their scope
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215081930.11477-3-chris@chris-wilson.co.uk