v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the rcar-drif driver embeds it in the
rcar_drif_graph_ep structure. This causes memory corruption when the
notifier is destroyed at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The fwnode reference corresponding to the endpoint is leaked in an error
path of the rcar_drif_parse_subdevs() function. Fix it, and reorganize
fwnode reference handling in the function to release references early,
simplifying error paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP
mode with rcar-vin bridge noticed the capture worked fine for the first run
(with yavta), but for subsequent runs the bridge driver waited for the
frame to be captured. Debugging further noticed the data lines were
enabled/disabled in stream on/off callback and dumping the register
contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct
values, but yet frame capturing failed.
To get around this issue data lines are enabled in s_power callback.
(Also the sensor remains in power down mode if not streaming so power
consumption shouldn't be affected)
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for adding DVP configuration in s_power callback
move mipi configuration into separate function
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Keep the sensor in software power down mode and wake up only in
ov5640_set_stream_dvp() callback.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pr_info() was accidentally used to print the link frequencies whereas the
rest of the information is printed on debug level. Fix that by using
pr_debug() also for link frequencies.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Alan Chiang's e-mail address no longer works. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Update Copyright year to cover the previous changes and at the same time
address indentation issues.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are assignments inside the functions which are useless.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pcim_iomap_table() won't fail if previous pcim_iomap_regions() hasn't.
Since we check pcim_iomap_regions() for failure the check close to
pcim_iomap_table() is bogus and not needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's unclear why driver repeats the code from PCI core.
Drop it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We may use special helper macro to poll IO till condition or timeout
occurs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor cio2_buffer_done() to get rid of infinite loop by replacing it by
one with clear exit condition. This change also allows to check for an
error ahead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are few nice macros in pfn.h, some of which we may use here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's quite unlikely that another page size will be supported,
but in any case there is still an inconsistency between custom
page size definition and generic macros used in the driver.
Switch over to the generic PAGE_SIZE for sake of the consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This constant is used in several places in the code, define it
for better maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The code looks more nicer if we use:
while (i--)
instead:
for (i = i - 1; i >= 0; i--)
This would also allow making 'i' unsigned again.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When devm_ioremap_resource() fails, isp should be
freed just like other error paths in isp_probe.
Fixes: 8644cdf972 ("[media] omap3isp: Replace many MMIO regions by two")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Color Matching Descriptor has been present in USB cameras since
the original version of UVC, but it has never been fully exposed
in Linux.
This change informs V4L2 of all of the UVC colorspace parameters:
color primaries, transfer characteristics, and YCbCr encoding.
videodev2.h doesn't have values for all the possible UVC color settings,
so it is mapped as closely as possible.
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
bFrameIndex and bFormatIndex can be negotiated by the camera during
probing, resulting in the camera choosing a different format than
expected. v4l2 can already accommodate such changes, but the code was
not updating the proper fields.
Without such a change, v4l2 would potentially interpret the payload
incorrectly, causing corrupted output. This was happening on the
Elgato HD60 S+, which currently always renegotiates to format 1.
As an aside, the Elgato firmware is buggy and should not be renegotating,
but it is still a valid thing for the camera to do. Both macOS and Windows
will properly probe and read uncorrupted images from this camera.
With this change, both qv4l2 and chromium can now read uncorrupted video
from the Elgato HD60 S+.
[Add blank lines, remove periods at the of messages]
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UBSAN reports a shift-out-of-bounds warning in uvc_get_le_value(). The
report is correct, but the issue should be harmless as the computed
value isn't used when the shift is negative. This may however cause
incorrect behaviour if a negative shift could generate adverse side
effects (such as a trap on some architectures for instance).
Regardless of whether that may happen or not, silence the warning as a
full WARN backtrace isn't nice.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes the following coccinelle report:
drivers/media/usb/uvc/uvc_ctrl.c:1860:5-11:
ERROR: invalid reference to the index variable of the iterator on line 1854
by adding a boolean variable to check if the loop has found the
Found using - Coccinelle (http://coccinelle.lip6.fr)
[Replace cursor variable with bool found]
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is only 1 error exit in uvc_ctrl_add_info(), so using goto style
error handling is not necessary. Also the kfree(ctrl->uvc_data) on error
is not necessary, because the only error exit is for the kzalloc() of
ctrl->uvc_data failing.
Remove all the error handling cruft and simply do "return -ENOMEM" on
kzalloc() failure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
uvc_ctrl_add_info() calls uvc_ctrl_get_flags() which will override
the fixed-up flags set by uvc_ctrl_fixup_xu_info().
uvc_ctrl_init_xu_ctrl() already calls uvc_ctrl_get_flags() before
calling uvc_ctrl_add_info(), so the uvc_ctrl_get_flags() call in
uvc_ctrl_add_info() is not necessary for xu ctrls.
This commit moves the uvc_ctrl_get_flags() call for normal controls
from uvc_ctrl_add_info() to uvc_ctrl_init_ctrl(), so that we no longer
call uvc_ctrl_get_flags() twice for xu controls and so that we no longer
override the fixed-up flags set by uvc_ctrl_fixup_xu_info().
This fixes the xu motor controls not working properly on a Logitech
046d:08cc, and presumably also on the other Logitech models which have
a quirk for this in the uvc_ctrl_fixup_xu_info() function.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media controller core prints a warning when an entity is registered
without a function being set. This affects the uvcvideo driver, as the
warning was added without first addressing the issue in existing
drivers. The problem is harmless, but unnecessarily worries users. Fix
it by mapping UVC entity types to MC entity functions as accurately as
possible using the existing functions.
Fixes: b50bde4e47 ("[media] v4l2-subdev: use MEDIA_ENT_T_UNKNOWN for new subdevs")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add HEVC GUID and assotiate with HEVC pixel format so that frame
based format descriptors recognized by the UVC video driver.
Signed-off-by: Dmitry Buzdyk <dima.buzdyk@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The formula (2) is to convert from SOF to host clock,
it should be fix as
"TS = ((TS2 - TS1) * SOF + TS1 * SOF2 - TS2 * SOF1) / (SOF2 - SOF1)"
Signed-off-by: Jun Chen <jun.chen@vatics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix this warning:
vivid-core.c: In function 'vivid_create_devnodes':
vivid-core.c:1318:11: warning: unused variable 'i' [-Wunused-variable]
1318 | int ret, i;
| ^
and this error:
vivid-core.c: In function 'vivid_create_instance':
vivid-core.c:1885:47: error: 'cec_tx_bus_cnt' undeclared (first use in this function)
1885 | ret = vivid_create_devnodes(pdev, dev, inst, cec_tx_bus_cnt,
| ^~~~~~~~~~~~~~
vivid-core.c:1885:47: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into patchwork
Linux 5.9-rc4
* tag 'v5.9-rc4': (1001 commits)
Linux 5.9-rc4
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
...
If something fails after calling v4l2_device_register(),
it should call v4l2_device_put().
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to reduce even further the size of the big
vivid_create_instance() function, let's place the part of the
logic which creates the device nodes into a separate function.
With this and the past patches, those warnings finally
vanishes:
drivers/media/test-drivers/vivid/vivid-core.c: drivers/media/test-drivers/vivid/vivid-core.c:1189 vivid_create_instance() parse error: turning off implications after 60 seconds
drivers/media/test-drivers/vivid/vivid-core.c: drivers/media/test-drivers/vivid/vivid-core.c:1257 vivid_create_instance() parse error: __split_smt: function too hairy. Giving up after 303 seconds
The init code also seems more organized after breaking the long
function into a smaller set.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of placing everything inside vivid_create_instance(),
we can move the part which creates per-type video queues
into a separate function.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move such logic from vivid_create_instance(), as otherwise
smatch takes forever.
The vivid_create_instance() is still a too big for my taste.
So, further cleanups are still needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The vivid_create_instance() function is too harry. Smatch can't
process it, because it takes too long.
The detection part is an important piece of it. As such, there
are even comments before and after such block.
So, it makes sense to just move it to a separate function.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OwNa
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a compilation fix issue with ti-vpe on arm 32 bits
- two Kconfig fixes for imx214 and max9286 drivers
- a kernel information leak at v4l2-core on time32 compat ioctls
- some fixes at rc core unbind logic
- a fix at mceusb driver for it to not use GFP_ATOMIC
- fixes at cedrus and vicodec drivers at the control handling logic
- a fix at gpio-ir-tx to avoid disabling interruts on a spinlock
* tag 'media/v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mceusb: Avoid GFP_ATOMIC where it is not needed
media: gpio-ir-tx: spinlock is not needed to disable interrupts
media: rc: do not access device via sysfs after rc_unregister_device()
media: rc: uevent sysfs file races with rc_unregister_device()
media: max9286: Depend on OF_GPIO
media: i2c: imx214: select V4L2_FWNODE
media: cedrus: Add missing v4l2_ctrl_request_hdl_put()
media: vicodec: add missing v4l2_ctrl_request_hdl_put()
media: media/v4l2-core: Fix kernel-infoleak in video_put_user()
media: ti-vpe: cal: Fix compilation on 32-bit ARM
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Both TT-connect S2-3600 and Pinnacle PCTV Sat HDTV are using
Intersil ISL6423 as LNB voltage regulator. This makes
TT-connect S2-3650 CI the only device which uses STM LNBP22 regulator
which is currently used for all devices driven by pctv452e driver.
This patch fixes this by creating an exception for TT-connect S2-3650 CI
to continue to use STM LNBP22 while all others now using correct ISL6423
driver which makes DiSEqC/EN50494 comands which involve voltage changes
now working on the other devices (which didn't work before).
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following versioncheck warning:
drivers/media/dvb-frontends/mxl5xx.c:30:1: unused including
<linux/version.h>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/pci/saa7134//saa7134-tvaudio.c:686 saa_dsp_writel() warn: should 'reg << 2' be a 64 bit type?
On a 64-bits Kernel, the shift might be bigger than 32 bits.
In real, this should never happen, but let's shut up the warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of calling printk(), use pr_foo() macros.
While here, do some cleanup at the printed messages, as some
has __func__, while others have the module name (sometimes
spelled as "ttusb_dvb").
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:311 ttusb_boot_dsp() error: doing dma on the stack (b)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:321 ttusb_boot_dsp() error: doing dma on the stack (b)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:330 ttusb_boot_dsp() error: doing dma on the stack (b)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:351 ttusb_set_channel() error: doing dma on the stack (b)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:361 ttusb_del_channel() error: doing dma on the stack (b)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:412 ttusb_init_controller() error: doing dma on the stack (b0)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:416 ttusb_init_controller() error: doing dma on the stack (b1)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:422 ttusb_init_controller() error: doing dma on the stack (b2)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:425 ttusb_init_controller() error: doing dma on the stack (b3)
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:430 ttusb_init_controller() error: doing dma on the stack (get_version)
This driver still uses the USB stack for DMA transfers,
which is broken for a long time. I almost dropped this driver,
as there's a high chance that nobody is using it with upstream
Kernels, as we didn't receive any bug reports.
As fixing this won't be hard, I ended opting to fix.
While here, I dropped an ugly hack that implemented read via
a separate function that was just doing a memcpy().
It should be noticed that, during the init phase, there's
a "b4" register that were never initialized, as its buffer
were used just to store the results of "b3" initialization.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/pci/saa7134/saa7134-alsa.c:267 saa7134_alsa_dma_init() warn: should 'nr_pages << 12' be a 64 bit type?
the number of patches should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/pci/cx88/cx88-alsa.c:286 cx88_alsa_dma_init() warn: should 'nr_pages << 12' be a 64 bit type?
the number of patches should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media//pci/cx23885/cx23885-alsa.c:83 cx23885_alsa_dma_init() warn: should 'nr_pages << 12' be a 64 bit type?
the number of patches should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/pci/cx25821/cx25821-alsa.c:146 cx25821_alsa_dma_init() warn: should 'nr_pages << 12' be a 64 bit type?
the number of patches should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/v4l2-core/videobuf-dma-sg.c:245 videobuf_dma_init_kernel() warn: should 'nr_pages << 12' be a 64 bit type?
The printk should not be using %d for the number of pages.
After looking better, the real problem here is that the
number of pages should be long int.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/rc/serial_ir.c:550 serial_ir_probe() warn: should '8 << ioshift' be a 64 bit type?
the "8" constant should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The usage of castings and float point when checking for
the setup based at the symbol_rate cause those warnings
with smatch:
drivers/media/dvb-frontends/tda10021.c:153 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:155 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:157 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:159 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
While the code should work with gcc, as it will evaluate the
values into a constant before compiling, other compilers
could do otherwise. So, get rid of float pointing math on it,
avoiding the need of doing typecasts.
While here, cleanup some coding style issues at the related
code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sparse warns about this symbol:
drivers/media/platform/qcom/venus/hfi_venus.c:133:5: warning: symbol 'venus_fw_debug' was not declared. Should it be static?
Because hfi_venus.c doesn't include a header file with the
extern. So, move it to core.h, with is included by both
hfi_venus.c and dbgfs.c.
This way, if something changes with it, warnings or errors
will be produced.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/radio/wl128x/fmdrv_common.c:736 fm_irq_handle_rdsdata_getcmd_resp() warn: potential spectre issue 'rds_fmt.data.groupdatabuff.buff>
Address it by using array_index_nospec().
While here, reorder the linux/ includes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While smatch reports an issue there:
drivers/media/pci/ttpci/av7110_v4l.c:163 ves1820_set_tv_freq() warn: unsigned 'freq' is never less than zero.
drivers/media/pci/ttpci/av7110_v4l.c:165 ves1820_set_tv_freq() warn: unsigned 'freq' is never less than zero.
The logic is actually fine. Yet, removing the typecast
shuts up smatch and makes the code more readable.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As pointed by smatch:
drivers/media/tuners/qt1010.c:239 qt1010_init_meas1() error: uninitialized symbol 'val2'.
drivers/media/tuners/qt1010.c:273 qt1010_init_meas2() error: uninitialized symbol 'val'.
The logic is ok, but it is hard for static analyzers
to parse it, as it depends on a value read in the middle
of a loop.
Also, it takes a while for humans to verify.
Re-write the first function to use a more direct way.
At the second one, I opted to just initialize the read var,
in order to shut up the report.
While here, address a few coding style issues at the
function code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The original logic had an integer to unsigned integer
conversion, plus a float-point math. While gcc should be
able to do the match at compile time, other compilers might
not do the same. Also, those produce the following warnings
with static code analyzers:
drivers/media/dvb-frontends/tda10086.c:300 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:303 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:306 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:309 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:312 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:315 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:318 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:321 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:324 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:327 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
Change the logic to declare the reference constant as unsigned
and to not use float point math.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here we introduce debug prefixes for dev_dbg groups by level of
importance - Venus{Low,Med,High,FW} Enabling the particular level
will be done by dynamic debug.
For example to enable debug messages with low level:
echo 'format "VenusLow" +p' > debugfs/dynamic_debug/control
If you want to enable all levels:
echo 'format "Venus" +p' > debugfs/dynamic_debug/control
All the features which dynamic debugging provide are preserved.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This will be useful when debugging specific issues related to
firmware HFI interface.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the standard menu control for frame skip mode in the MFC
driver. The legacy private menu control is kept for backward
compatibility.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds support for frame-skip-mode standard v4l2 control in
encoder driver. The control is implemented based on the
combination of client selected bitrate-mode and frame-skip-mode.
Once The client selected bitrate-mode (constant or variable) and
the frame-skip-mode is not disabled we set variable framerate for
rate controller.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds encoders standard v4l2 control for frame-skip. The control
is a copy of a custom encoder control so that other v4l2 encoder
drivers can use it.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds implementation of V4L2_CID_MPEG_VIDEO_CONSTANT_QUALITY v4l
control when the bitrate mode is CQ.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When V4L2_CID_MPEG_VIDEO_BITRATE_MODE value is
V4L2_MPEG_VIDEO_BITRATE_MODE_CQ, encoder will produce
constant quality output indicated by
V4L2_CID_MPEG_VIDEO_CONSTANT_QUALITY control value.
Encoder will choose appropriate quantization parameter
and bitrate to produce requested frame quality level.
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the recovery mechanism is using two hfi functions
to destroy and create interface queues. For the purpose of
recovery we don't need to free and allocate the memory used
for interface message queues, that's why we introduce new
function which just reinit the queues. Also this will give
to the recovery procedure one less reason to fail (if for
some reason we couldn't allocate memory).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After power domains and clock restructuring the recovery for
sdm845 and v4 did not work properly. Fix that by reworking the
recovery function and the sequence.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the hfi_parser has been called only once during driver
probe. To prepare the parser function to be called multiple times
from recovery we need to initialize few variables which are used
during parsing time.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On dragonboard-410c (apq8016) with HFI_VERSION_1XX, the reported
framerate is in unit of 1/65535 fps (for fine grained control).
So the current reported supported frame intervals is wrong (max
is 1/65535 fps), leading to encoding issues or format negotiation
failures with gstreamer.
Fix that by setting the framerate denominator to coherent value
based on the the framerate factor.
The factor is not always the same, e.g. with db820c (apq8096) HFI
reports framerate in fps unit. So only apply that for HFI_VERSION_1XX.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are few list handling issues while adding and deleting
node in the registered buf list in the driver.
1. list addition - buffer added into the list during buf_init
while not deleted during cleanup.
2. list deletion - In capture streamoff, the list was reinitialized.
As a result, if any node was present in the list, it would
lead to issue while cleaning up that node during buf_cleanup.
Corresponding call traces below:
[ 165.751014] Call trace:
[ 165.753541] __list_add_valid+0x58/0x88
[ 165.757532] venus_helper_vb2_buf_init+0x74/0xa8 [venus_core]
[ 165.763450] vdec_buf_init+0x34/0xb4 [venus_dec]
[ 165.768271] __buf_prepare+0x598/0x8a0 [videobuf2_common]
[ 165.773820] vb2_core_qbuf+0xb4/0x334 [videobuf2_common]
[ 165.779298] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 165.784053] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 165.789067] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 165.794624] v4l_qbuf+0x48/0x58
[ 1797.556001] Call trace:
[ 1797.558516] __list_del_entry_valid+0x88/0x9c
[ 1797.562989] vdec_buf_cleanup+0x54/0x228 [venus_dec]
[ 1797.568088] __buf_prepare+0x270/0x8a0 [videobuf2_common]
[ 1797.573625] vb2_core_qbuf+0xb4/0x338 [videobuf2_common]
[ 1797.579082] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 1797.583830] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 1797.588843] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 1797.594389] v4l_qbuf+0x48/0x58
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The H.264 specification requires in section 7.4.3 "Slice header semantics",
that the following values shall be the same in all slice headers:
pic_parameter_set_id
frame_num
field_pic_flag
bottom_field_flag
idr_pic_id
pic_order_cnt_lsb
delta_pic_order_cnt_bottom
delta_pic_order_cnt[ 0 ]
delta_pic_order_cnt[ 1 ]
sp_for_switch_flag
slice_group_change_cycle
These bitstream fields are part of the slice header, and therefore
passed redundantly on each slice. The purpose of the redundancy
is to make the codec fault-tolerant in network scenarios.
This is of course not needed to be reflected in the V4L2 controls,
given the bitstream has already been parsed by applications.
Therefore, move the redundant fields to the per-frame decode
parameters control (DECODE_PARAMS).
Field 'pic_parameter_set_id' is simply removed in this case,
because the PPS control must currently contain the active PPS.
Syntax elements dec_ref_pic_marking() and those related
to pic order count, remain invariant as well, and therefore,
the fields dec_ref_pic_marking_bit_size and pic_order_cnt_bit_size
are also common to all slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
DPB entry PicNum maximum value is 2*MaxFrameNum for interlaced
content (field_pic_flag=1).
As specified, MaxFrameNum is 2^(log2_max_frame_num_minus4 + 4)
and log2_max_frame_num_minus4 is in the range of 0 to 12,
which means pic_num should be a 32-bit field.
The v4l2_h264_dpb_entry struct needs to be padded to avoid a hole,
which might be also useful to allow future uAPI extensions.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As discussed recently, the current interface for the
Decoded Picture Buffer is not enough to properly
support field coding.
This commit introduces enough semantics to support
frame and field coding, and to signal how DPB entries
are "used for reference".
Reserved fields will be added by a follow-up commit.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The prediction weight parameters are only required under
certain conditions, which depend on slice header parameters.
As specified in section 7.3.3 Slice header syntax, the prediction
weight table is present if:
((weighted_pred_flag && (slice_type == P || slice_type == SP)) || \
(weighted_bipred_idc == 1 && slice_type == B))
Given its size, it makes sense to move this table to its control,
so applications can avoid passing it if the slice doesn't specify it.
Before this change struct v4l2_ctrl_h264_slice_params was 960 bytes.
With this change, it's 188 bytes and struct v4l2_ctrl_h264_pred_weight
is 772 bytes.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The unit of exposure value is different from other OmniVision sensors,
driver will divide by 2 before set register, the exposure range exposed
by v4l2 ctrl to user should be same as others, so the calculation for
the maximum exposure value in current driver need be fixed.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis reports this error
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the error return from the call to max9286_read is masked
with 0xf0 so the following check for a negative error return is
never true. Fix this by checking for an error first, then masking
the return value for subsequent conflink_mask checking.
Addresses-Coverity: ("Logically dead code")
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Although the code is correct and doing the right thing, the clock diagram
showed the wrong register for the bit divider, which had me doubting the
understanding of the tree. Fix this to avoid doubts in the future.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OTP data was not ready after registered as nvmem device, it is
risky as the nvmem read may happen once the device exists, this patch
get the OTP data ready before registering the nvmem device. OTP data
missing should not break the normal camera sensor probe, so use a
warning instead of an error message.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vidioc_streamoff can be called multiple times from userspace, but we
should only call media_pipeline_stop when we're actually setup.
This became more noticeable after commit 2a2599c663 ("[media] media:
entity: Catch unbalanced media_pipeline_stop calls") was merged as it
added a WARN for unbalanced calls to media_pipeline_stop.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is no longer used since the conversion to DT
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a no-op as it is never set and is a remnant from non-DT days
that can be safely removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some devices, there may be multiple camera sensors attached
to the same port. Make sure we probe all of them, not just the
first one.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of keeping a local copy of how many sensors we've probed
(which may not even properly represent the number of sensors
probed if we have a port without a sensor), use the global
num_sensors counter that has the actual number used.
This will also make it easier to add support for multiple sensors
being connected to the same port.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ee7160e57c ("[media] s5p-fimc: Add support for JPEG capture")
added support for JPEG capture, but missed setting a register when the
parallel port was used rather than the CSIS device.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit bae4500399 ("[media] exynos4-is: Add missing entity function
initialization") tried to suppress the warnings such as
s5p-fimc-md camera: Entity type for entity FIMC.0 was not initialized!
However, this missed setting for the subdev. Set it now to avoid the
ugly warnings on boot.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Not all devices use the CSIS device, some may use the FIMC directly in
which case the CSIS device isn't registered. This leads to a nullptr
exception when starting the stream as the CSIS device is always
referenced. Instead, if getting the CSIS device fails, try getting the
FIMC directly to check if we are using the subdev API
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
