The timestamps in ir-keytable -t output showed that the Xbox DVD
IR dongle decodes scancodes every 64ms. The last scancode of a
longer button press is decodes 64ms after the last-but-one which
indicates the decoder doesn't use a timeout but decodes on the last
edge of the signal.
267.042629: lirc protocol(unknown): scancode = 0xace
267.042665: event type EV_MSC(0x04): scancode = 0xace
267.042665: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.042665: event type EV_SYN(0x00).
267.106625: lirc protocol(unknown): scancode = 0xace
267.106643: event type EV_MSC(0x04): scancode = 0xace
267.106643: event type EV_SYN(0x00).
267.170623: lirc protocol(unknown): scancode = 0xace
267.170638: event type EV_MSC(0x04): scancode = 0xace
267.170638: event type EV_SYN(0x00).
267.234621: lirc protocol(unknown): scancode = 0xace
267.234636: event type EV_MSC(0x04): scancode = 0xace
267.234636: event type EV_SYN(0x00).
267.298623: lirc protocol(unknown): scancode = 0xace
267.298638: event type EV_MSC(0x04): scancode = 0xace
267.298638: event type EV_SYN(0x00).
267.543345: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.543345: event type EV_SYN(0x00).
267.570015: event type EV_KEY(0x01) key_up: KEY_1(0x0002)
267.570015: event type EV_SYN(0x00).
Add a protocol with the repeat value and set the timeout in the
driver to 10ms (to have a bit of headroom for delays) so the Xbox
DVD remote performs more responsive.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit f1a2e44a3a ("bpf: add queue and stack maps") introduced new BPF
helper functions:
- BPF_FUNC_map_push_elem
- BPF_FUNC_map_pop_elem
- BPF_FUNC_map_peek_elem
but they were made available only for network BPF programs. This patch
makes them available for tracepoint, cgroup and lirc programs.
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Cc: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use codespell to fix lots of typos over frontends.
Manually verified to avoid false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When an rc device is created, we do not know what key codes it will
support, since a new keymap might be loaded at some later point. So,
we set all keybit in the input device.
The uevent for the input device includes all the key codes, of which
there are now 768. This overflows the size of the uevent
(UEVENT_BUFFER_SIZE) and no event is generated.
Revert for now until we figure out a different solution.
This reverts commit fec225a043.
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Christian Holpert <christian@holpert.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Zotac RC2604323/01G and RC2604329/02BG remotes use the 32-bit
rc6 protocol and toggle bit 15 (0x8000) on repeated button presses,
like MCE remotes.
Add the customer code 0x80340000 to the 32-bit rc6 toggle
handling code to get proper scancodes and toggle reports.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: add support for RCMM infrared remote controls.
Signed-off-by: Patrick Lerda <patrick9876@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Some IR remotes have a directional pad or other pointer-like thing that
can be used as a mouse. Make it possible to decode these types of IR
protocols in BPF.
Cc: netdev@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
If userspace has an open file descriptor on the rc input device or lirc
device when rc_unregister_device() is called, then the rc close() is
never called.
This ensures that the receiver is turned off on the nuvoton-cir driver
during shutdown.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strcpy() function is being deprecated. Replace it by the
safer strscpy().
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Previously, the code would loop for each of the 40 bits. Now it will
branch for each edge in the IR, which will be much less.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The xbox dvd remote sends 24 bits, the first 12 bits are repeated
and inverted so only 12 bits are used. The upper 4 bits can be read
at offset 3. Ensure we pass this to rc-core and update the keymap
accordingly.
Tested-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Xbox DVD Movie Playback Kit is a USB dongle with an IR remote for the
Original Xbox.
Historically it has been supported by the out-of-tree lirc_xbox driver,
but this one has fallen out of favour and was just dropped from popular
Kodi (formerly XBMC) distributions.
This driver is heavily based on the ati_remote driver where all the
boilerplate was taken from - I was mostly just removing code.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The three following Hauppauge USB DVB devices have IR receivers, but
lacked the support in mceusb to enable it:
- WinTV-HVR-935C
- WinTV-HVR-955Q
- WinTV-HVR-975
Tested HVR-955Q and HVR-975 plus RC5 remote and irw, works as intended.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to create another input device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to create another input device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
libevdev (which is used by libinput) gets a list of keycodes from the
input device on creation. Any events with keycodes which are not in this
list are silently dropped. So, set all keycodes on device creation since
we do not know which will be used if the keymap changes.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Kathrein RCU-676 remote uses the 32-bit rc6 protocol and toggles
bit 15 (0x8000) on repeated button presses, like MCE remotes.
Add it's customer code 0x80460000 to the 32-bit rc6 toggle
handling code to get proper scancodes and toggle reports.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Since commit cafa0010cd ("Raise the minimum required gcc version to
4.6"), this is the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rc_proto field should list the exact variant used by the remote. This
does not change the decoder used, but helps with using keymaps for
transmit purposes.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add cgroup local storage for BPF programs, which provides a fast
accessible memory for storing various per-cgroup data like number
of transmitted packets, etc, from Roman.
2) Support bpf_get_socket_cookie() BPF helper in several more program
types that have a full socket available, from Andrey.
3) Significantly improve the performance of perf events which are
reported from BPF offload. Also convert a couple of BPF AF_XDP
samples overto use libbpf, both from Jakub.
4) seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header.
Adds this action now to the seg6local BPF interface, from Mathieu.
5) Do not mark dst register as unbounded in MOV64 instruction when
both src and dst register are the same, from Arthur.
6) Define u_smp_rmb() and u_smp_wmb() to their respective barrier
instructions on arm64 for the AF_XDP sample code, from Brian.
7) Convert the tcp_client.py and tcp_server.py BPF selftest scripts
over from Python 2 to Python 3, from Jeremy.
8) Enable BTF build flags to the BPF sample code Makefile, from Taeung.
9) Remove an unnecessary rcu_read_lock() in run_lwt_bpf(), from Taehee.
10) Several improvements to the README.rst from the BPF documentation
to make it more consistent with RST format, from Tobin.
11) Replace all occurrences of strerror() by calls to strerror_r()
in libbpf and fix a FORTIFY_SOURCE build error along with it,
from Thomas.
12) Fix a bug in bpftool's get_btf() function to correctly propagate
an error via PTR_ERR(), from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=TwSI
-----END PGP SIGNATURE-----
Merge tag 'media/v4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a deadlock regression at vsp1 driver
- some Remote Controller fixes related to the new BPF filter logic
added on it for Kernel 4.18.
* tag 'media/v4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: v4l: vsp1: Fix deadlock in VSPDL DRM pipelines
media: rc: read out of bounds if bpf reports high protocol number
media: bpf: ensure bpf program is freed on detach
media: rc: be less noisy when driver misbehaves
This patch converts bpf_prog_array from an array of prog pointers
to the array of struct bpf_prog_array_item elements.
This allows to save a cgroup storage pointer for each bpf program
efficiently attached to a cgroup.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The repeat period is read from a static array. If a keydown event is
reported from bpf with a high protocol number, we read out of bounds. This
is unlikely to end up with a reasonable repeat period at the best of times,
in which case no timely key up event is generated.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently we are leaking bpf programs when they are detached from the
lirc device; the refcount never reaches zero.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 48231f289e ("media: rc: drivers should produce alternate
pulse and space timing events"), on meson-ir we are regularly producing
errors. Reduce to warning level and only warn once to avoid flooding
the log.
A proper fix for meson-ir is going to be too large for v4.18.
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org # 4.17+
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the kernel is compiled with CONFIG_CGROUP_BPF not enabled, it is not
possible to attach, detach or query IR BPF programs to /dev/lircN devices,
making them impossible to use. For embedded devices, it should be possible
to use IR decoding without cgroups or CONFIG_CGROUP_BPF enabled.
This change requires some refactoring, since bpf_prog_{attach,detach,query}
functions are now always compiled, but their code paths for cgroups need
moving out. Rather than a #ifdef CONFIG_CGROUP_BPF in kernel/bpf/syscall.c,
moving them to kernel/bpf/cgroup.c and kernel/bpf/sockmap.c does not
require #ifdefs since that is already conditionally compiled.
Fixes: f4364dcfc8 ("media: rc: introduce BPF_PROG_LIRC_MODE2")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Here are the main updates for SoC support (besides DT additions) for ARM
32- and 64-bit platforms. The branch also contains defconfig updates to
turn on drivers and options as needed on the various platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products.
-----BEGIN PGP SIGNATURE-----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=S5wc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
-----BEGIN PGP SIGNATURE-----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=r/WP
-----END PGP SIGNATURE-----
Merge tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove of atomisp driver from staging, as nobody would have time to
dedicate huge efforts to fix all the problems there. Also, we have a
feeling that the driver may not even run the way it is.
- move Zoran driver to staging, in order to be either fixed to use VB2
and the proper media kAPIs or to be removed
- remove videobuf-dvb driver, with is unused for a while
- some V4L2 documentation fixes/improvements
- new sensor drivers: imx258 and ov7251
- a new driver was added to allow using I2C transparent drivers
- several improvements at the ddbridge driver
- several improvements at the ISDB pt1 driver, making it more coherent
with the DVB framework
- added a new platform driver for MIPI CSI-2 RX: cadence
- now, all media drivers can be compiled on x86 with COMPILE_TEST
- almost all media drivers now build on non-x86 architectures with
COMPILE_TEST
- lots of other random stuff: cleanups, support for new board models,
bug fixes, etc
* tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
media: omap2: fix compile-testing with FB_OMAP2=m
media: media/radio/Kconfig: add back RADIO_ISA
media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl()
media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
media: arch: sh: migor: Fix TW9910 PDN gpio
media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure
media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG
media: marvel-ccic: allow ccic and mmp drivers to coexist
media: uvcvideo: Prevent setting unavailable flags
media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges
media: dvb-frontends/stv0910: make TS speed configurable
media: ddbridge/mci: add identifiers to function definition arguments
media: ddbridge/mci: protect against out-of-bounds array access in stop()
media: rc: ensure input/lirc device can be opened after register
media: rc: nuvoton: Keep device enabled during reg init
media: rc: nuvoton: Keep track of users on CIR enable/disable
media: rc: nuvoton: Tweak the interrupt enabling dance
media: uvcvideo: Support realtek's UVC 1.5 device
media: uvcvideo: Fix driver reference counting
media: gspca_zc3xx: Enable short exposure times for OV7648
...
Add support for BPF_PROG_LIRC_MODE2. This type of BPF program can call
rc_keydown() to reported decoded IR scancodes, or rc_repeat() to report
that the last key should be repeated.
The bpf program can be attached to using the bpf(BPF_PROG_ATTACH) syscall;
the target_fd must be the /dev/lircN device.
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit cb84343fce ("media: lirc: do not call close() or open() on
unregistered devices") rc_open() will return -ENODEV if rcdev->registered
is false. Ensure this is set before we register the input device and the
lirc device, else we have a short window where the neither the lirc or
input device can be opened.
Fixes: cb84343fce ("media: lirc: do not call close() or open() on unregistered devices")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Doing writes when the device is disabled seems to be a NOOP.
For CIR device, we should enable it, initialize it, and then disable it
until it's opened. CIR_WAKE should always be enabled.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Core rc keeps track of the users - let's use it to tweak the code and
use the common code path on suspend/resume.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It appears that we need to enable CIR device before attempting to touch
some of the registers. Previously, this was not a big issue, since we
were rarely seeing nvt_close() getting called.
Unfortunately, since commit cb84343fce ("media: lirc: do not call close()
or open() on unregistered devices") the initial open() during probe from
rc_setup_rx_device() is no longer successful, which means that userspace
clients will actually end up calling nvt_open()/nvt_close(). Since
nvt_open() is broken, the device doesn't seem to work as expected.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199597
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The minimum possible timeout of ite-cir is 8 samples, which is
typically about 70us. The driver however changes the FIFO trigger
level from the hardware's default of 1 byte to 17 bytes, so the minimum
usable timeout value is 17 * 8 samples, which is typically about 1.2ms.
Tests showed that using timeouts down to 1.2ms actually work fine.
The current default timeout of 200ms is much longer than necessary and
the maximum timeout of 1s seems to have been chosen a bit arbitrarily.
So change the minimum timeout to the driver's limit of 17 * 8 samples
and bring timeout and maximum timeout in line with the settings
of many other receivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ir_raw_event_set_idle() sends a timeout event which is not needed, and
on startup no reset event is needed either.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drivers should never produce consecutive pulse or space raw events. Should
that occur, we would have bigger problems than this code is trying to
guard against.
Note that we already log an error should a driver misbehave.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report an error if this is not the case or any problem with the generated
raw events.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Any spaces events received after a reset or startup should be discarded,
so ensure the rc device is in idle mode.
This also makes it much easier to detect incorrect raw events, as we will
do in a following commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A mceusb device has been observed producing invalid irdata. Proactively
guard against this.
Suggested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the IR timeout is set on vid 1784 pid 0011, the device starts
behaving strangely.
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
-----BEGIN PGP SIGNATURE-----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=jYZ6
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
ti-sysc driver related changes for omap variants
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
* tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Show module information for suspend if DEBUG is enabled
bus: ti-sysc: Tag sdio and wdt with legacy mode for suspend
bus: ti-sysc: Detect UARTs for SYSC_QUIRK_LEGACY_IDLE quirk on omap4
bus: ti-sysc: Detect omap4 type timers for quirk
bus: ti-sysc: Add initial support for external resets
bus: ti-sysc: Improve suspend and resume handling
bus: ti-sysc: Tag some modules resource providers for noirq suspend
bus: ti-sysc: Add handling for clkctrl opt clocks
bus: ti-sysc: Make child clock alias handling more generic
bus: ti-sysc: Handle simple-bus for nested children
ARM: OMAP2+: Make display related init into device_initcall
ARM: OMAP2+: Initialize SoC PM later
ARM: OMAP2+: Only probe SDMA via ti-sysc if configured in dts
ARM: OMAP2+: Use signed value for sysc register offsets
ARM: OMAP2+: Allow using ti-sysc for system timers
ARM: OMAP2+: Drop unused pm-noop
Signed-off-by: Olof Johansson <olof@lixom.net>
The pnp header already provide enough stub to build those
drivers with COMPILE_TEST on non-x86 archs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The iMON PAD controller has a analog stick, which can be switched to
keyboard mode (cursor keys) or work as a crappy mouse.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The raw_register function exists to create input devices associated with
that IR protocol.
If the mce_kbd module is loaded, then every rc device will have mce_kbd
input devices, even if the protocol is not enabled. Change this to call
the register function to when the protocol is enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The usage of of_device_get_match_data() reduce the code size a bit.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Because I will be leaving Samsung soon, update my e-mail to the
etezian.org mail.
Cc: Andi Shyti <andi@etezian.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mceusb devices have a default timeout of 100ms, but this can be changed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last usb packet with IR data will end with 0x80 (MCE_IRDATA_TRAILER).
If we reset the decoder state at this point, IR decoding can fail.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MCE keyboard sends both key down and key up events. We have a timeout
handler mce_kbd_rx_timeout() in case the keyup event is never received;
however, this may race with new key down events from occurring.
The race is that key down scancode arrives and key down events are
generated. The timeout handler races this and generates key up events
straight afterwards. Since the keyboard generates scancodes every 100ms,
most likely the keys will be repeated 100ms later, and now we have new
key down events and the user sees duplicate key presses.
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is nothing to sync in this code path.
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MCE Remote sends a 0 scancode when keys are released. If this is not
received or decoded, then keys can get "stuck"; the keyup event is not
sent since the input_sync() is missing from the timeout handler.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If two keys are pressed, then both keys are encoded in the scancode. This
makes the mce keyboard more responsive.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mce keyboard repeats pressed keys every 100ms. If the IR timeout
is set to less than that, we send key up events before the repeat
arrives, so we have key up/key down for each IR repeat.
The keyboard ends any sequence with a 0 scancode, in which case all keys
are cleared so there is no need to run the timeout timer: it only exists
for the case that the final 0 was not received.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Each IR protocol has its own repeat period. We can minimise the keyup
timer to be the protocol period + IR timeout. This makes keys less
"sticky" and makes IR more reactive and nicer to use.
This feature was previously attempted in commit d57ea877af ("media: rc:
per-protocol repeat period"), but that did not take the IR timeout into
account, and had to be reverted.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the kernel now modifies the timeout, make it possible to retrieve
the current value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The longer the IR timeout, the longer the rc device waits until delivering
the trailing space. So, by reducing this timeout, we reduce the delay for
the last scancode to be delivered.
Note that the lirc daemon disables all protocols, in which case we revert
back to the default value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On the raspberry pi, we might have two lirc devices; one for sending and
one for receiving. This change makes it much more apparent which one
is which.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/rc/st_rc.c:110 st_rc_rx_interrupt() warn: this loop depends on readl() succeeding
If something goes wrong at readl(), the logic will stay there
inside an IRQ code forever. This is not the nicest thing to
do :-)
So, add a timeout there, preventing staying inside the IRQ
for more than 10ms.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Looks like these functions don't do anything in the mainline kernel so
we can just drop it.
Note that we must now also remove ir-rx51 pdata as it relies on the dummy
platform data that does not do anything. And ir-rx51 is calling a pdata
callback that doesn't do anything without checking if it exists first.
For configuring device specific minimal latencies, the interface to use
is pm_qos_add_request(). For an example, see what was done in commit
9834ffd1ec ("ASoC: omap-mcbsp: Add PM QoS support for McBSP to prevent
glitches"). I've added some comments to ir-rx51 so people using it can
add pm_qos support and test it.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----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=bzhS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a23a ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.
This reverts commit f41003a23a.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.
This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG IR device driver. The hardware is also present on MIPS SoCs so
the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Sean Young <sean@mess.org>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-media@vger.kernel.org
Cc: linux-metag@vger.kernel.org
There is a possible race condition between the IR timeout being generated
from the timer, and new IR arriving. This could result in the timeout
being added to the kfifo after new IR arrives. On top of that, there is
concurrent write access to the kfifo from ir_raw_event_store_edge() and
the timer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit a60d64b15c ("media: lirc: lirc interface should not be
a raw decoder"), the message in the documentation is incorrect as the
module name is rc_core, not lirc_dev. Since the message is not useful,
just make the message debug and remove it from the documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code gets the start time before copying the IR from
userspace (could cause page faults) and encoding IR. This means
that the gap calculation could be off.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Calculate the pulse rather than having a few preset values.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return code of clk_prepare_enable() is ignored in many places.
The patch adds error handling for all of them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I usually update my config with make oldconfig and pressing return,
trusting that whoever updates Kconfig sets sensible defaults.
But my recent kernels ended up with all kinds of IR decoders
built in that are not used by anything because they are all
marked with default y.
default y should only be set for something that prevents
booting on common systems, never for some random weirdo
driver feature like this.
Remove all the "default y" in drivers/media/rc/Kconfig
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The rc5 protocol does not have a leading pulse or space, but we encode
the first bit using a single leading pulse. For other protocols, the
leading pulse or space does not represent any bit. So, don't remove the
first bit if a leading pulse is present.
Cc: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IR rc6 encoder sends the header using manchester encoding using 0
bits, which causes the following:
UBSAN: Undefined behaviour in drivers/media/rc/rc-ir-raw.c:247:6
shift exponent 4294967295 is too large for 64-bit type 'long long unsigned int'
So, allow the leader code to send a pulse and space and remove the unused
pulse_space_start field.
Cc: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 9b6192589b ("media: lirc: implement scancode sending"),
and commit de142c3241 ("media: lirc: implement reading scancode")
the lirc features ioctl for raw IR devices advertises two modes for
sending and receiving.
The lirc daemon now fails to detect a raw IR device, both for transmit
and receive.
To fix this, do not advertise the scancode mode in the lirc features
for raw IR devices (however do keep it for scancode devices). The mode
can still be used via the LIRC_SET_{REC,SEND}_MODE ioctl.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit a60d64b15c ("media: lirc: lirc interface should not be
a raw decoder"), there is no lirc_dev module any more. On Ubuntu 16.10,
the /etc/init.d/lirc startup script attempts to load the lirc_dev module.
Since this module does not exist any more, this script fails. Add an alias
so the correct module is loaded.
Fixes: a60d64b15c ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current error exit path if ir_raw_encode_scancode fails is via the
label out_kfree which kfree's an uninitialized pointer txbuf. Fix this
by exiting via a new exit path that does not kfree txbuf. Also exit
via this new exit path for a failed allocation of txbuf to avoid a
redundant kfree on a NULL pointer (to save a bunch of CPU cycles).
Detected by: CoverityScan, CID#1463070 ("Uninitialized pointer read")
Fixes: f81a8158d4 ("media: lirc: release lock before sleep")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no reason to hold the lock while we wait for the IR to transmit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is code existed for when drivers would send less than the whole
buffer; no driver does this any more, so this is redundant. Drivers
should return -EINVAL if they cannot send the entire buffer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If memdup_user() fails, txbuf will be an error pointer and passed
to kfree.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The TX loop is more complex than it should. Simplify it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semantics for lirc IR transmit with raw IR is that the write call
should block until the IR is transmitted. Some drivers have no idea
when this actually is (e.g. mceusb), so there is a wait.
This is useful for userspace, as it might want to send a IR button press,
a gap of a predefined number of milliseconds, and then send a repeat
message.
It turns out that for transmitting scancodes this feature is even more
useful, as user space has no idea how long the IR is. So, maintain
the existing semantics for IR scancode transmit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 9c7fd60e951d ("media: rc: Replace timeval with ktime_t in
imon.c"), the function tv2int() is no longer used. Remove it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Another device with the 0xffdc device id, this one with 0x26 in the
config byte. Its an iMON Inside + iMON IR. It does respond to rc-6,
but seems to produce random garbage rather than a scancode.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The agreed format is to use /* */ comments inside header
files. Unfortunately, I ended by using // on a few ones.
Reported-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c9 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Another device with the 0xffdc device id, this one with 0x30 in the
config byte. Its an iMON VFD + iMON IR (it does not understand rc6).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pnp_irq() function returns -1 if an error occurs.
pnp_irq() error checking for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch changes the 32-bit time type (timeval) to the 64-bit one
(ktime_t), since 32-bit time types will break in the year 2038.
I use ktime_t instead of all uses of timeval in imon.c
This patch also changes do_gettimeofday() to ktime_get() accordingly,
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval, and the other reason is that ktime_get() uses
the monotonic clock.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once rc_unregister_device() has been called, no driver function
should be called.
This prevents some nasty race conditions with an ioctl calls
driver functions when the driver specific data has been freed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible for lircd to read from a lirc chardev, and not
keep it busy.
Note that this changes the default for timeout reports to on. lircd
already enables timeout reports when it opens a lirc device, leaving
them on until the next reboot.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This removes the need for include/media/lirc.h, which just includes
the uapi file.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since removing the lirc kapi, ir-lirc-codec.c only contains lirc fops
so the file name is no longer correct. By moving its content into
lirc_dev.c the ugly extern struct lirc_fops is not longer needed,
and everything lirc related is in one file.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the lirc interface supports scancodes, RC scancode devices
can also have a lirc device. The only receiving feature they will have
enabled is LIRC_CAN_REC_SCANCODE.
Note that CEC devices have no lirc device, since they can be controlled
from their /dev/cecN chardev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc device should get lirc repeats whether there is a keymap
match or not.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
rc-core has replaced the lirc kapi many years ago, and now with the last
driver ported to rc-core, we can finally remove it.
Note this has no effect on userspace.
All future IR drivers should use the rc-core api.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the generic kernel lirc api with ones which use rc-core, further
reducing the lirc_dev members.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If a lirc chardev is held open after a device is unplugged, rc_close()
will be called after rc_unregister_device(). The driver is not expecting
any calls at this point, and the iguanair driver causes an oops in
this scenario.
rc_open() can be called when the device is removed too, by calling open
on the chardev whilst the device is being removed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is done to further remove the lirc kernel api. Ensure that every
fops checks for this.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the only mode lirc devices can handle is raw IR, handle this
in a plain kfifo.
Remove lirc_buffer since this is no longer needed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Calculate lirc features when necessary, and add LIRC_{S,G}ET_REC_MODE
cases to ir_lirc_ioctl.
This makes lirc_dev_fop_ioctl() unnecessary since all cases are
already handled by ir_lirc_ioctl().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For some IR protocols, some scancode values not valid, i.e. they're part
of a different protocol variant.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Ensure we reject an attempt to transmit invalid scancodes.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc user interface exists as a raw decoder, which does not make
much sense for transmit-only devices.
In addition, we want to have lirc char devices for devices which do not
use raw IR, i.e. scancode only devices.
Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of
each other, so they've been merged into one module rc-core to avoid
circular dependencies.
Since ir-lirc-codec no longer exists as separate codec module, there is no
need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When sending scancodes, load the encoder if we need it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the lirc device supports it, set the carrier for the protocol.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This introduces a new lirc mode: scancode. Any device which can send raw IR
can now also send scancodes.
int main()
{
int mode, fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_SEND_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode = {
.scancode = 0x1e3d,
.rc_proto = RC_PROTO_RC5,
};
write(fd, &scancode, sizeof(scancode));
close(fd);
}
The other fields of lirc_scancode must be set to 0.
Note that toggle (rc5, rc6) and repeats (nec) are not implemented. Nor is
there a method for holding down a key for a period.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
LIRCCODE is a lirc mode where a driver produces driver-dependent
codes for receive and transmit. No driver uses this any more. The
LIRC_GET_LENGTH ioctl was used for this mode only.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on the several
RC keymap files I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to identify GPL v2, as this is the
minimal license requirement for those modles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit d57ea877af ("media: rc: per-protocol repeat period"), most
IR protocols have a lower keyup timeout. This causes problems on the
ite-cir, which has default IR timeout of 200ms.
Since the IR decoders read the trailing space, with a IR timeout of 200ms,
the last keydown will have at least a delay of 200ms. This is more than
the protocol timeout of e.g. rc-6 (which is 164ms). As a result the last
IR will be interpreted as a new keydown event, and we get two keypresses.
Revert the protocol timeout to 250ms, except for cec which needs a timeout
of 550ms.
Fixes: d57ea877af ("media: rc: per-protocol repeat period")
Cc: <stable@vger.kernel.org> # 4.14
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several parameters there that are named wrong, as
reported by those warnings:
drivers/media/rc/ir-sharp-decoder.c:47: warning: No description found for parameter 'ev'
drivers/media/rc/ir-sharp-decoder.c:47: warning: Excess function parameter 'duration' description in 'ir_sharp_decode'
drivers/media/rc/ir-sanyo-decoder.c:56: warning: No description found for parameter 'ev'
drivers/media/rc/ir-sanyo-decoder.c:56: warning: Excess function parameter 'duration' description in 'ir_sanyo_decode'
drivers/media/rc/ir-xmp-decoder.c:43: warning: No description found for parameter 'ev'
drivers/media/rc/ir-xmp-decoder.c:43: warning: Excess function parameter 'duration' description in 'ir_xmp_decode'
drivers/media/rc/ir-jvc-decoder.c:47: warning: No description found for parameter 'ev'
drivers/media/rc/ir-jvc-decoder.c:47: warning: Excess function parameter 'duration' description in 'ir_jvc_decode'
drivers/media/rc/ir-lirc-codec.c:34: warning: No description found for parameter 'dev'
drivers/media/rc/ir-lirc-codec.c:34: warning: No description found for parameter 'ev'
drivers/media/rc/ir-lirc-codec.c:34: warning: Excess function parameter 'input_dev' description in 'ir_lirc_decode'
drivers/media/rc/ir-lirc-codec.c:34: warning: Excess function parameter 'duration' description in 'ir_lirc_decode'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function documentation here doesn't follow kernel-doc,
as parameters aren't documented. So, stop abusing on
"/**" markups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some parameters aren't correctly identified, as noticed by
those warnings:
drivers/media/rc/ir-nec-decoder.c:49: warning: No description found for parameter 'ev'
drivers/media/rc/ir-nec-decoder.c:49: warning: Excess function parameter 'duration' description in 'ir_nec_decode'
drivers/media/rc/ir-nec-decoder.c:189: warning: Excess function parameter 'raw' description in 'ir_nec_scancode_to_raw'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleanup those warnings:
drivers/media/rc/rc-ir-raw.c:141: warning: No description found for parameter 'ev'
drivers/media/rc/rc-ir-raw.c:141: warning: Excess function parameter 'type' description in 'ir_raw_event_store_with_filter'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Needed to suppress the following warnings:
drivers/media/rc/img-ir/img-ir-hw.c:351: warning: No description found for parameter 'reg_timings'
drivers/media/rc/img-ir/img-ir-hw.c:351: warning: Excess function parameter 'timings' description in 'img_ir_decoder_convert'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Building the driver with gcc 7.2.1 and:
make ARCH=i386 CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y W=1 CHECK='' M=drivers/media
now produces a lot of warnings:
drivers/media/rc/rc-main.c:278: warning: No description found for parameter 'new_keycode'
drivers/media/rc/rc-main.c:278: warning: Excess function parameter 'keycode' description in 'ir_update_mapping'
drivers/media/rc/rc-main.c:387: warning: No description found for parameter 'ke'
drivers/media/rc/rc-main.c:387: warning: No description found for parameter 'old_keycode'
drivers/media/rc/rc-main.c:387: warning: Excess function parameter 'scancode' description in 'ir_setkeycode'
drivers/media/rc/rc-main.c:387: warning: Excess function parameter 'keycode' description in 'ir_setkeycode'
drivers/media/rc/rc-main.c:433: warning: Excess function parameter 'to' description in 'ir_setkeytable'
drivers/media/rc/rc-main.c:506: warning: No description found for parameter 'ke'
drivers/media/rc/rc-main.c:506: warning: Excess function parameter 'scancode' description in 'ir_getkeycode'
drivers/media/rc/rc-main.c:506: warning: Excess function parameter 'keycode' description in 'ir_getkeycode'
drivers/media/rc/rc-main.c:634: warning: No description found for parameter 't'
drivers/media/rc/rc-main.c:634: warning: Excess function parameter 'cookie' description in 'ir_timer_keyup'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaG1X1AAoJEHm+PkMAQRiGLcMH/iZ0K7obuuqVZCs1j0EeBTHB
WTy+uhIND+7Zrdz+UXM9xcisyzSHKbrIqOzXygXNqoYPGqqQF+o2grw8xoSftxPG
/Pashmda3gF+GTxpNJ5ZXjNoGlWJ/egiZZKTilJ1oBHAgSpTvK/e9KGY0zgimOEy
KAQUYzydtxKrXl72/ybX64FiJNmTu13PFD5uWvMsxfQstbyLhPU8B2XgoNSSe2TA
lxYPIt5P3X+5EjfdrhmEYqANjqyHp2cWBOGkocqyfYbXlJKfhmNu/Ar61yz21LXd
M+vk7vkEZ7QWaHjtPS4M3noBqu3PIy6JPxYgZ+huBIxlK0BF5RSwSTfVMfrV4y0=
=cZ6Z
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rc1' into patchwork
Linux 4.15-rc1
* tag 'v4.15-rc1': (12179 commits)
Linux 4.15-rc1
ARM: BUG if jumping to usermode address in kernel mode
m68k/macboing: Fix missed timer callback assignment
afs: remove redundant assignment of dvnode to itself
afs: cell: Remove unnecessary code in afs_lookup_cell
afs: Fix signal handling in some file ops
afs: Fix some dentry handling in dir ops and missing key_puts
afs: Make afs_write_begin() avoid writing to a page that's being stored
sched/debug: Fix task state recording/printout
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
ipvlan: Fix insufficient skb linear check for ipv6 icmp
ipvlan: Fix insufficient skb linear check for arp
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
...
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Without this test, sir_ir clumsy claims resources for a device which
does not exist.
The 0-day kernel test robot reports the following errors (in a loop):
sir_ir sir_ir.0: Trapped in interrupt
genirq: Flags mismatch irq 4. 00000000 (ttyS0) vs. 00000000 (sir_ir)
When sir_ir is loaded with the default io and irq, the following happens:
- sir_ir claims irq 4
- user space opens /dev/ttyS0
- in serial8250_do_startup(), some setup is done for ttyS0, which causes
irq 4 to fire (in THRE test)
- sir_ir does not realise it was not for it, and spins until the "trapped
in interrupt"
- now serial driver calls setup_irq() and fails and we get the
"Flags mismatch" error.
There is no port present at 0x3e8 so simply check for the presence of a
port, as suggested by Linus.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
