This adds support for multigig copper SFP modules from RollBall/Hilink.
These modules have a specific way to access clause 45 registers of the
internal PHY.
We also need to wait at least 22 seconds after deasserting TX disable
before accessing the PHY. The code waits for 25 seconds just to be sure.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some multigig SFPs from RollBall and Hilink do not expose functional
MDIO access to the internal PHY of the SFP via I2C address 0x56
(although there seems to be read-only clause 22 access on this address).
Instead these SFPs PHY can be accessed via I2C via the SFP Enhanced
Digital Diagnostic Interface - I2C address 0x51. The SFP_PAGE has to be
selected to 3 and the password must be filled with 0xff bytes for this
PHY communication to work.
This extends the mdio-i2c driver to support this protocol by adding a
special parameter to mdio_i2c_alloc function via which this RollBall
protocol can be selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of configuring the I2C mdiobus when SFP driver is probed,
create/destroy the mdiobus before the PHY is probed for/after it is
released.
This way we can tell the mdio-i2c code which protocol to use for each
SFP transceiver.
Move the code that determines MDIO I2C protocol from
sfp_sm_probe_for_phy() to sfp_sm_mod_probe(), where most of the SFP ID
parsing is done. Don't allocate I2C bus if no PHY is expected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros SFP_QUIRK(), SFP_QUIRK_M() and SFP_QUIRK_F() for defining SFP
quirk table entries. Use them to deduplicate the code a little bit.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFPs may contain an internal PHY which may in some cases want to
connect with the host interface in 1000base-x/2500base-x mode.
Do not fail if such PHY is being attached in one of these PHY interface
modes.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the host interface configuration according to the capabilities of
the host if the host provided them. This is currently provided only when
connecting PHY that is inside a SFP.
The PHY supports several configurations of host communication:
- always communicate with host in 10gbase-r, even if copper speed is
lower (rate matching mode),
- the same as above but use xaui/rxaui instead of 10gbase-r,
- switch host SerDes mode between 10gbase-r, 5gbase-r, 2500base-x and
sgmii according to copper speed,
- the same as above but use xaui/rxaui instead of 10gbase-r.
This mode of host communication, called MACTYPE, is by default selected
by strapping pins, but it can be changed in software.
This adds support for selecting this mode according to which modes are
supported by the host.
This allows the kernel to:
- support SFP modules with 88X33X0 or 88E21X0 inside them
Note: we use mv3310_select_mactype() for both 88X3310 and 88X3340,
although 88X3340 does not support XAUI. This is not a problem because
88X3340 does not declare XAUI in it's supported_interfaces, and so this
function will never choose that MACTYPE.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ rebase, updated, also added support for 88E21X0 ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register definitions were defined with spaces used for indentation.
Change them to tabs.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the supported PHY interface types to phylib if the PHY we are
connecting is inside a SFP, so that the PHY driver can select an
appropriate host configuration mode for their interface according to
the host capabilities.
For example the Marvell 88X3310 PHY inside RollBall SFP modules
defaults to 10gbase-r mode on host's side, and the marvell10g
driver currently does not change this setting. But a host may not
support 10gbase-r. For example Turris Omnia only supports sgmii,
1000base-x and 2500base-x modes. The PHY can be configured to use
those modes, but in order for the PHY driver to do that, it needs
to know which modes are supported.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_sfp_config() now only deals with configuring the MAC for a
SFP containing a PHY. Rename it to be specific.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a MAC provides a phy_interface_t bitmap, use these bitmaps to
select the operating interface mode for optical SFP modules, rather
than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having the ability to validate all supported interface
modes or a single interface mode, introduce the ability to validate
a subset of supported modes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[ rebased on current net-next ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liu Jian says:
====================
Add helper functions to parse netlink msg of ip_tunnel
v1->v2: Move the implementation of the helper function to ip_tunnel_core.c
v2->v3: Change EXPORT_SYMBOL to EXPORT_SYMBOL_GPL
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip_tunnel_netlink_parms to parse netlink msg of ip_tunnel_parm.
Reduces duplicate code, no actual functional changes.
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip_tunnel_netlink_encap_parms to parse netlink msg of ip_tunnel_encap.
Reduces duplicate code, no actual functional changes.
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Refactor selftests to use an array of structs in xfrm_fill_key().
From Gautam Menghani.
2) Drop an unused argument from xfrm_policy_match.
From Hongbin Wang.
3) Support collect metadata mode for xfrm interfaces.
From Eyal Birger.
4) Add netlink extack support to xfrm.
From Sabrina Dubroca.
Please note, there is a merge conflict in:
include/net/dst_metadata.h
between commit:
0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
from the net-next tree and commit:
5182a5d48c ("net: allow storing xfrm interface metadata in metadata_dst")
from the ipsec-next tree.
Can be solved as done in linux-next.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao says:
====================
refactor duplicate codes in bind_class hook function
All the bind_class callback duplicate the same logic, so we can refactor
them. First, ensure n arg not empty before call bind_class hook function.
Then, add tc_cls_bind_class() helper. Last, use tc_cls_bind_class() in
filter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All the bind_class callback duplicate the same logic, this patch
introduces tc_cls_bind_class() helper for common usage.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All bind_class callbacks are directly returned when n arg is empty.
Therefore, bind_class is invoked only when n arg is not empty.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 xsk updates part3 2022-09-30
The gist of this 4 part series is in this patchset's last patch
This series contains performance optimizations. XSK starts using the
batching allocator, and XSK data path gets separated from the regular
RX, allowing to drop some branches not relevant for non-XSK use cases.
Some minor optimizations for indirect calls and need_wakeup are also
included.
Other than that, this series adds a few features to the mlx5e
implementation of XSK:
1. XDP metadata support on XSK RQs.
2. RSS contexts support for XSK RQs.
3. Some other optimizations
4. Last but not least, change the queuing scheme, so that XSK RQs no longer
use higher indices, but replace the regular RQs.
Maxim Says:
==========
In the initial implementation of XSK in mlx5e, XSK RQs coexisted with
regular RQs in the same channel. The main idea was to allow RSS work the
same for regular traffic, without need to reconfigure RSS to exclude XSK
queues.
However, this scheme didn't prove to be beneficial, mainly because of
incompatibility with other vendors. Some tools don't properly support
using higher indices for XSK queues, some tools get confused with the
double amount of RQs exposed in sysfs. Some use cases are purely XSK,
and allocating the same amount of unused regular RQs is a waste of
resources.
This commit changes the queuing scheme to the standard one, where XSK
RQs replace regular RQs on the channels where XSK sockets are open. Two
RQs still exist in the channel to allow failsafe disable of XSK, but
only one is exposed at a time. The next commit will achieve the desired
memory save by flushing the buffers when the regular RQ is unused.
As the result of this transition:
1. It's possible to use RSS contexts over XSK RQs.
2. It's possible to dedicate all queues to XSK.
3. When XSK RQs coexist with regular RQs, the admin should make sure no
unwanted traffic goes into XSK RQs by either excluding them from RSS or
settings up the XDP program to return XDP_PASS for non-XSK traffic.
4. When using a mixed fleet of mlx5e devices and other netdevs, the same
configuration can be applied. If the application supports the fallback
to copy mode on unsupported drivers, it will work too.
==========
Part 4 will include some final xsk optimizations and minor improvements
part 1: https://lore.kernel.org/netdev/20220927203611.244301-1-saeed@kernel.org/
part 2: https://lore.kernel.org/netdev/20220929072156.93299-1-saeed@kernel.org/
====================
Link: https://lore.kernel.org/r/20220930162903.62262-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the initial implementation of XSK in mlx5e, XSK RQs coexisted with
regular RQs in the same channel. The main idea was to allow RSS work the
same for regular traffic, without need to reconfigure RSS to exclude XSK
queues.
However, this scheme didn't prove to be beneficial, mainly because of
incompatibility with other vendors. Some tools don't properly support
using higher indices for XSK queues, some tools get confused with the
double amount of RQs exposed in sysfs. Some use cases are purely XSK,
and allocating the same amount of unused regular RQs is a waste of
resources.
This commit changes the queuing scheme to the standard one, where XSK
RQs replace regular RQs on the channels where XSK sockets are open. Two
RQs still exist in the channel to allow failsafe disable of XSK, but
only one is exposed at a time. The next commit will achieve the desired
memory save by flushing the buffers when the regular RQ is unused.
As the result of this transition:
1. It's possible to use RSS contexts over XSK RQs.
2. It's possible to dedicate all queues to XSK.
3. When XSK RQs coexist with regular RQs, the admin should make sure no
unwanted traffic goes into XSK RQs by either excluding them from RSS or
settings up the XDP program to return XDP_PASS for non-XSK traffic.
4. When using a mixed fleet of mlx5e devices and other netdevs, the same
configuration can be applied. If the application supports the fallback
to copy mode on unsupported drivers, it will work too.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function to flush an RQ: clean up descriptors, release pages and
reset the RQ. This procedure is used by the recovery flow, and it will
also be used in a following commit to free some memory when switching a
channel to the XSK mode.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for XDP metadata on XSK RQs for cross-program
communication. The driver no longer calls xdp_set_data_meta_invalid and
copies the metadata to a newly allocated SKB on XDP_PASS.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_free_rx_mpwqe loops over all pages of a MPWQE, calling
mlx5e_page_release for ones that are not scheduled for XDP_TX or
XDP_REDIRECT; and mlx5e_page_release checks whether it's an XSK RQ or a
regular one for each page/XSK frame. This check can be moved outside the
loop to reduce the number of branches.
mlx5e_free_rx_wqe loops over all fragments, calling mlx5e_page_release
for the ones that are last in a page; and mlx5e_page_release checks
whether it's an XSK RQ or a regular one for each fragment. Using the
fact that XSK doesn't support multiple fragments, it can be optimized
for both XSK and regular usages:
1. Make an early check for XSK and call its deallocator directly, saving
3 branches (loop condition, frag->last_in_page and selection of
deallocator).
2. Call the regular deallocator directly in the non-XSK case, saving a
branch per fragment, except the first one.
After the changes, mlx5e_page_release is removed, as there are no
callers left.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_page_release calls the appropriate deallocator depending on
whether it's an XSK RQ or a regular one. Some flows that call this
function are not compatible with XSK, so they can call the non-XSK
deallocator directly to save a branch.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SHAMPO flow is not compatible with XSK, it can call the page pool
allocator directly to save a branch.
mlx5e_page_alloc is removed, as it's no longer used in any flow.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XSK provides a function to allocate frames in batches for more efficient
processing. This commit starts using this function on striding RQ and
creates an optimized flow for XSK. A side effect is an opportunity to
optimize the regular RX flow by dropping branching for XSK cases.
Performance improvement is up to 6.4% in the aligned mode and up to 7.5%
in the unaligned mode.
Aligned mode, 2048-byte frames: 12.9 Mpps -> 13.8 Mpps
Aligned mode, 4096-byte frames: 11.8 Mpps -> 12.5 Mpps
Unaligned mode, 2048-byte frames: 11.9 Mpps -> 12.8 Mpps
Unaligned mode, 3072-byte frames: 11.4 Mpps -> 12.1 Mpps
Unaligned mode, 4096-byte frames: 11.0 Mpps -> 11.2 Mpps
CPU: Intel(R) Xeon(R) Gold 6240 CPU @ 2.60GHz
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XSK provides a function to allocate frames in batches for more efficient
processing. This commit starts using this function on legacy RQ, adding
a special case for XSK. The new branch introduced basically replaces the
branch that was removed from the same place a few commits before.
A check is made that DMA sync is not needed, because the batching
allocator falls back to returning one frame when DMA sync is needed, and
this is best handled by the loop in the standard case.
Performance improvement is up to 8% in the aligned mode and up to 9% in
the unaligned mode.
Aligned mode, 2048-byte frames: 12.8 Mpps -> 13.5 Mpps
Aligned mode, 4096-byte frames: 11.5 Mpps -> 12.4 Mpps
Unaligned mode, 2048-byte frames: 12.2 Mpps -> 13.4 Mpps
Unaligned mode, 3072-byte frames: 11.6 Mpps -> 12.5 Mpps
Unaligned mode, 4096-byte frames: 11.2 Mpps -> 12.2 Mpps
CPU: Intel(R) Xeon(R) Gold 6240 CPU @ 2.60GHz
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocation of XSK frames on legacy RQ may be made more efficient with a
specialized routine that relies on certain assumptions, such as there is
only one fragment, allocation units (XSK frames) are not shared among
multiple packets. It reduces the number of branches both in the XSK code
and in the regular RQ, because with this approach there is only a single
check whether it's an XSK or regular RQ.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Legacy RQ WQEs are allocated in a loop in small batches (8 WQEs). As
partial batches are allowed, there is no point to have a loop in a loop,
so the outer loop is removed, and the batch size is increased up to the
total number of WQEs to allocate, still not smaller than 8.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit allowed allocating WQE batches in legacy RQ
partially, however, XSK still checks whether there are enough frames in
the fill ring. Remove this check to allow to allocate batches partially
also with XSK.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Legacy RQ allocates WQEs in batches. If the batch allocation fails, the
pages of the allocated part are released. This commit changes this
behavior to allow to use the pages that have been already allocated.
After this change, we need to be careful about indexing rq->wqe.frags[].
The WQ size is a power of two that divides by wqe_bulk (8), and the old
code used whole bulks, which allowed to use indices [8*K; 8*K+7] without
overflowing. Now that the bulks may be partial, the range can start at
any location (not only at 8*K), so we need to wrap them around to avoid
out-of-bounds array access.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old calculation of wqe_index_mask may give false positives, i.e.
request bulking of pairs of WQEs when not strictly needed, for example,
when the first fragment size is equal to the PAGE_SIZE, bulking is not
needed, even if the number of fragments is odd.
Make the calculation more exact to cut false positives.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When fragments of different WQEs share the same page, mlx5e_post_rx_wqes
must wait until the old WQE stops using the page, only then the new WQE
can allocate the new page. Essentially, it means that if WQE index i is
still in use, the allocation must stop before `i % bulk`, where bulk is
the number of WQEs that may share the same page.
As bulk is always a power of two, `i % bulk = i & (bulk - 1)`, and the
new wqe_index_mask field will be equal to `bulk - 1`.
At the same time, wqe_bulk remains for optimization purposes and stores
`max(bulk, 8)`, which allows to skip the allocation until we have at
least 8 WQEs free.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MLX5E_CHANNEL_STATE_XSK flag checked in mlx5e_xsk_wakeup indicates
that XSK queues are open, but not necessarily activated. This check is
not very useful, because:
0. Both XSK setup and netdev state transitions take the same state_lock
mutex, so they can't happen at the same time.
1. If the netdev is up, xsk_is_bound can return true only when
MLX5E_CHANNEL_STATE_XSK is set on the corresponding channel.
mlx5e_xsk_wakeup is only called when xsk_is_bound is true.
2. If the XSK socket is bound, and the netdev is going up or down,
mlx5e_xsk_wakeup can take one of two branches, depending on the return
value of napi_if_scheduled_mark_missed:
2.1. True means one of two things: either NAPI was enabled at this
point, which means MLX5E_CHANNEL_STATE_XSK was also set; or NAPI was
disabled, and nothing really happened.
2.2. False means that NAPI was enabled by this point, which also implies
MLX5E_CHANNEL_STATE_XSK was set. Additionally, mlx5e_xsk_wakeup contains
a following check for MLX5E_SQ_STATE_ENABLED on async_icosq, and this
flag implies MLX5E_CHANNEL_STATE_XSK too on XSK channels.
As checking this flag doesn't cut any flows, remove the check.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_xsk_wakeup triggers an IRQ by posting a NOP to async_icosq, taking
a spinlock to protect from concurrent access. There is already a
function that does the same: mlx5e_trigger_napi_icosq. Use this function
in mlx5e_xsk_wakeup.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman says:
====================
nfp: support FEC mode reporting and auto-neg
this series adds support for the following features to the nfp driver:
* Patch 1/5: Support active FEC mode
* Patch 2/5: Don't halt driver on non-fatal error when interacting with fw
* Patch 3/5: Treat port independence as a firmware rather than port property
* Patch 4/5: Support link auto negotiation
* Patch 5/5: Support restart of link auto negotiation
====================
Link: https://lore.kernel.org/r/20220929085832.622510-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support restart of link auto-negotiation.
This may be initiated using:
# ethtool -r <intf>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the auto negotiation capability if it's supported
in management firmware, and advertise it if it's enabled.
Changing port speed is not allowed when autoneg is enabled.
The ethtool <intf> command displays the auto-neg capability:
# ethtool enp1s0np0
Settings for enp1s0np0:
Supported ports: [ FIBRE ]
Supported link modes: Not reported
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Supported FEC modes: None RS BASER
Advertised link modes: Not reported
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: None RS BASER
Speed: 25000Mb/s
Duplex: Full
Auto-negotiation: on
Port: FIBRE
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Considering that whether application firmware is indifferent to
port speed is a firmware property instead of port property, now use
a new rtsym to get the property instead of parsing per-port tlv caps.
With this change, relevant code is moved to `nfp_main` layer.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's not a fatal error when setting `hwinfo` into management firmware
fails, no need to halt the whole driver initialization process.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The latest management firmware can now report the active FEC
mode. Adapt driver accordingly so that user can get the active
FEC mode by running command:
# ethtool --show-fec <intf>
Also correct use of `fec` field.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since three patchsets "add tc-testing test cases", "refactor duplicate
codes in the tc cls walk function", and "refactor duplicate codes in the
qdisc class walk function" are merged to net-next tree, the list of
supported features needs to be updated in config file.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20220929041909.83913-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reset line is supposed to be "active low" (it even says so in the
description), but examples incorrectly show it as "active high"
(likely because original examples use 0 which is technically "active
high" but in practice often "don't care" if the driver is using legacy
gpio API, as this one does).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/YzX+nzJolxAKmt+z@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko says:
====================
devlink: sanitize per-port region creation/destruction
Currently the only user of per-port devlink regions is DSA. All drivers
that use regions register them before devlink registration. For DSA,
this was not possible as the internals of struct devlink_port needed for
region creation are initialized during port registration.
This introduced a mismatch in creation flow of devlink and devlink port
regions. As you can see, it causes the DSA driver to make the port
init/exit flow a bit cumbersome.
Fix this by introducing port_init/fini() which could be optionally
called by drivers like DSA, to prepare struct devlink_port to be used
for region creation purposes before devlink port register is called.
Tested by Vladimir on his setup.
====================
Link: https://lore.kernel.org/r/20220929072902.2986539-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since dsa_port_devlink_setup() and dsa_port_devlink_teardown() are
already called from code paths which only execute once per port (due to
the existing bool dp->setup), keeping another dp->devlink_port_setup is
redundant, because we can already manage to balance the calls properly
(and not call teardown when setup was never called, or call setup twice,
or things like that).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 3122433eb5 ("net: dsa: Register devlink ports before calling DSA driver setup()")
moved devlink port setup to be done early before driver setup()
was called. That is no longer needed, so move the devlink port
initialization back to dsa_port_setup(), as the first thing done there.
Note there is no longer needed to reinit port as unused if
dsa_port_setup() fails, as it unregisters the devlink port instance on
the error path.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a desire to simplify the dsa_port registration path with
devlink, and this involves reworking a bit how user ports which fail to
connect to their PHY (because it's missing) get reinitialized as UNUSED
devlink ports.
The desire is for the change to look something like this; basically
dsa_port_setup() has failed, we just change dp->type and call
dsa_port_setup() again.
-/* Destroy the current devlink port, and create a new one which has the UNUSED
- * flavour.
- */
-static int dsa_port_reinit_as_unused(struct dsa_port *dp)
+static int dsa_port_setup_as_unused(struct dsa_port *dp)
{
- dsa_port_devlink_teardown(dp);
dp->type = DSA_PORT_TYPE_UNUSED;
- return dsa_port_devlink_setup(dp);
+ return dsa_port_setup(dp);
}
For an UNUSED port, dsa_port_setup() mostly only calls dsa_port_devlink_setup()
anyway, so we could get away with calling just that. But if we call the
full blown dsa_port_setup(dp) (which will be needed to properly set
dp->setup = true), the callee will have the tendency to go through this
code block too, and call dsa_port_disable(dp):
switch (dp->type) {
case DSA_PORT_TYPE_UNUSED:
dsa_port_disable(dp);
break;
That is not very good, because dsa_port_disable() has this hidden inside
of it:
if (dp->pl)
phylink_stop(dp->pl);
Fact is, we are not prepared to handle a call to dsa_port_disable() with
a struct dsa_port that came from a previous (and failed) call to
dsa_port_setup(). We do not clean up dp->pl, and this will make the
second call to dsa_port_setup() call phylink_stop() on a dangling dp->pl
pointer.
Solve this by creating an API for phylink destruction which is symmetric
to the phylink creation, and never leave dp->pl set to anything except
NULL or a valid phylink structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move port_setup() op to be called before devlink_port_register() and
port_teardown() after devlink_port_unregister().
Note it makes sense to move this alongside the rest of the devlink port
code, the reinit() function also gets much nicer, as clearly the fact that
port_setup()->devlink_port_region_create() was called in dsa_port_setup
did not fit the flow.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
