improve the common clock support code for MPC512x
- expand the CCM register set declaration with MPC5125 related registers
(which reside in the previously "reserved" area)
- tell the MPC5121, MPC5123, and MPC5125 SoC variants apart, and derive
the availability of components and their clocks from the detected SoC
(MBX, AXE, VIU, SPDIF, PATA, SATA, PCI, second FEC, second SDHC,
number of PSC components, type of NAND flash controller,
interpretation of the CPMF bitfield, PSC/CAN mux0 stage input clocks,
output clocks on SoC pins)
- add backwards compatibility (allow operation against a device tree
which lacks clock related specs) for MPC5125 FECs, too
telling SoC variants apart and adjusting the clock tree's generation
occurs at runtime, a common generic binary supports all of the chips
the MPC5125 approach to the NFC clock (one register with two counters
for the high and low periods of the clock) is not implemented, as there
are no users and there is no common implementation which supports this
kind of clock -- the new implementation would be unused and could not
get verified, so it shall wait until there is demand
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
the SDHC clock is derived from CSB with a fractional divider which can
address "quarters"; the implementation multiplies CSB by 4 and divides
it by the (integer) divider value
a bug in the clock domain synchronisation requires that only even
divider values get setup; we achieve this by
- multiplying CSB by 2 only instead of 4
- registering with CCF the divider's bit field without bit0
- the divider's lowest bit remains clear as this is the reset value
and later operations won't touch it
this change keeps fully utilizing common clock primitives (needs no
additional support logic, and avoids an excessive divider table) and
satisfies the hardware's constraint of only supporting even divider
values
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
adjust (expand on or move) a few comments,
add markers for easier navigation around helpers
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
this change removes workarounds which have become obsolete after
migration to common clock support has completed
- remove clkdev registration calls (compatibility clock item aliases)
after all peripheral drivers were adjusted for device tree based
clock lookup
- remove pre-enable workarounds after all peripheral drivers were
adjusted to acquire their respective clock items
workarounds for these clock items get removed: FEC (ethernet), I2C,
PSC (UART, SPI), PSC FIFO, USB, NFC (NAND flash), VIU (video capture),
BDLC (CAN), CAN MCLK, DIU (video output)
these clkdev registered names won't be provided any longer by the
MPC512x platform's clock driver: "psc%d_mclk", "mscan%d_mclk",
"usb%d_clk", "nfc_clk", "viu_clk", "sys_clk", "ref_clk"
the pre-enable workaround for PCI remains, but depends on the presence
of PCI related device tree nodes (disables the PCI clock in the absence
of PCI nodes, keeps the PCI clock enabled in the presence of nodes) --
moving clock acquisition into the peripheral driver isn't possible for
PCI because its initialization takes place before the platform clock
driver gets initialized, thus the clock provider isn't available then
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
adapt the DIU clock initialization to the COMMON_CLK approach:
device tree based clock lookup, prepare and unprepare for clocks,
work with frequencies not dividers, call the appropriate clk_*()
routines and don't access CCM registers
the "best clock" determination now completely relies on the
platform's clock driver to pick a frequency close to what the
caller requests, and merely checks whether the desired frequency
was met (fits the tolerance of the monitor)
this approach shall succeed upon first try in the usual case,
will test a few less desirable yet acceptable frequencies in
edge cases, and will fallback to "best effort" if none of the
previously tried frequencies pass the test
provide a fallback clock lookup approach in case the OF based clock
lookup for the DIU fails, this allows for successful operation in
the presence of an outdated device tree which lacks clock specs
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
transition to the common clock framework has completed and the PPC_CLOCK
is no longer available for the MPC512x platform, remove the now obsolete
code path of the mpc5xxx mscan driver which accessed clock control module
registers directly
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
implement a .get_clock() callback for the MPC512x platform which uses
the common clock infrastructure (eliminating direct access to the clock
control registers from within the CAN network driver), and provide the
corresponding .put_clock() callback to release resources after use
acquire both the clock items for register access ("ipg") as well as for
wire communication ("can")
keep the previous implementation of MPC512x support in place during
migration, this results in a readable diff of the change
this change is neutral to the MPC5200 platform
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the VIU driver
need no longer use the previous global "viu_clk" name, but should use
the "ipg" clock name specific to the OF node
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the NAND
flash driver need no longer use the previous global "nfc_clk" name,
but should use the "ipg" clock name specific to the OF node
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the component
index -- remove the "usb%d_clk" template, always use "ipg" instead
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
prepare and enable the FIFO clock upon PSC FIFO initialization,
check for and propagage errors when enabling the PSC FIFO clock,
disable and unprepare the FIFO clock upon PSC FIFO uninitialization
devm_{get,put}_clk() doesn't apply here, as the SoC provides a
single FIFO component which is shared among several PSC components,
thus the FIFO isn't associated with a device (while the PSCs are)
provide a fallback clock lookup approach in case the OF based clock
lookup for the PSC FIFO fails, this allows for successful operation in
the presence of an outdated device tree which lacks clock specs
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the "ipg" clock item for register access as well
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the 'ipg' clock item for register access as well
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
the setup before the change was
- arch/powerpc/Kconfig had the PPC_CLOCK option, off by default
- depending on the PPC_CLOCK option the arch/powerpc/kernel/clock.c file
was built, which implements the clk.h API but always returns -ENOSYS
unless a platform registers specific callbacks
- the MPC52xx platform selected PPC_CLOCK but did not register any
callbacks, thus all clk.h API calls keep resulting in -ENOSYS errors
(which is OK, all peripheral drivers deal with the situation)
- the MPC512x platform selected PPC_CLOCK and registered specific
callbacks implemented in arch/powerpc/platforms/512x/clock.c, thus
provided real support for the clock API
- no other powerpc platform did select PPC_CLOCK
the situation after the change is
- the MPC512x platform implements the COMMON_CLK interface, and thus the
PPC_CLOCK approach in arch/powerpc/platforms/512x/clock.c has become
obsolete
- the MPC52xx platform still lacks genuine support for the clk.h API
while this is not a change against the previous situation (the error
code returned from COMMON_CLK stubs differs but every call still
results in an error)
- with all references gone, the arch/powerpc/kernel/clock.c wrapper and
the PPC_CLOCK option have become obsolete, as did the clk_interface.h
header file
the switch from PPC_CLOCK to COMMON_CLK is done for all platforms within
the same commit such that multiplatform kernels (the combination of 512x
and 52xx within one executable) keep working
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
this addresses the client side of device tree based clock lookups
add clock specifiers to the mbx, nfc, mscan, sdhc, i2c, axe, diu, viu,
mdio, fec, usb, pata, psc, psc fifo, and pci nodes in the shared
mpc5121.dtsi include
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
extend the recently added COMMON_CLK platform support for MPC512x such
that it works with incomplete device tree data which lacks clock specs
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
[agust@denx.de: moved node macro definitions out of the function body]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
this change implements a clock driver for the MPC512x PowerPC platform
which follows the COMMON_CLK approach and uses common clock drivers
shared with other platforms
this driver implements the publicly announced set of clocks (those
listed in the dt-bindings header file), as well as generates additional
'struct clk' items where the SoC hardware cannot easily get mapped to
the common primitives (shared code) of the clock API, or requires
"intermediate clock nodes" to represent clocks that have both gates and
dividers
the previous PPC_CLOCK implementation is kept in place and remains
active for the moment, the newly introduced CCF clock driver will
receive additional support for backwards compatibility in a subsequent
patch before it gets enabled and will replace the PPC_CLOCK approach
some of the clock items get pre-enabled in the clock driver to not have
them automatically disabled by the underlying clock subsystem because of
their being unused -- this approach is desirable because
- some of the clocks are useful to have for diagnostics and information
despite their not getting claimed by any drivers (CPU, internal and
external RAM, internal busses, boot media)
- some of the clocks aren't claimed by their peripheral drivers yet,
either because of missing driver support or because device tree specs
aren't available yet (but the workarounds will get removed as the
drivers get adjusted and the device tree provides the clock specs)
clkdev registration provides "alias names" for few clock items
- to not break those peripheral drivers which encode their component
index into the name that is used for clock lookup (UART, SPI, USB)
- to not break those drivers which use names for the clock lookup which
were encoded in the previous PPC_CLOCK implementation (NFC, VIU, CAN)
this workaround will get removed as these drivers get adjusted after
device tree based clock lookup has become available
the COMMON_CLK implementation copes with device trees which lack an
oscillator node (backwards compat), the REF clock is then derived from
the IPS bus frequency and multiplier values fetched from hardware
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
this addresses the clock driver aka provider's side of clocks
- introduce a 'clocks' subtree with an 'osc' node for the crystal
or oscillator SoC input (fixed frequency)
- the 'clock@f00' clock-control-module node references the 'osc' for
its input, and is another provider for all the clocks which the
CCM component manages
- prepare for future references to clocks from peripheral nodes
by means of the <&clks ID> syntax and symbolic ID names which a
header file provides
- provide default values with 33MHz oscillator frequency in the
common include (the 66MHz IPS bus already was there), and add
override values for the ifm AC14xx board which deviates from
the reference design (25MHz xtal, 80MHz IPS bus)
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
introduce a dt-bindings/ header file for MPC512x clocks,
providing symbolic identifiers for those SoC clocks which
clients will reference from their device tree nodes
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Merge a pile of fixes that went into the "merge" branch (3.13-rc's) such
as Anton Little Endian fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The SLB save area is shared with the hypervisor and is defined
as big endian, so we need to byte swap on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the generic iommu backend code to use the
it_page_shift field to determine the iommu page size instead of
using hardcoded values.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a it_page_shift field to struct iommu_table and
initiliases it to 4K for all platforms.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the REDBOOT Kconfig parameter,
which was no longer used anywhere in the source code
and Makefiles.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With recent machine check patch series changes, The exception vectors
starting from 0x4300 are now overflowing with allyesconfig. Fix that by
moving machine_check_common and machine_check_handle_early code out of
that region to make enough room for exception vector area.
Fixes this build error reportes by Stephen:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:958: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:959: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:983: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:984: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1003: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1013: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1014: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1015: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1016: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1017: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:1018: Error: attempt to move .org backwards
[Moved the code further down as it introduced link errors due to too long
relative branches to the masked interrupts handlers from the exception
prologs. Also removed the useless feature section --BenH
]
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 5c0484e25e ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25e ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the USB controller's pin muxing is not setup
correctly and causes a kernel panic upon system startup, so
disable the USB1 device tree node in the MPC5125 tower board
dts file.
The USB controller is connected to an USB3320 ULPI transceiver
and the device tree should receive an update to reflect correct
dependencies and required initialization data before the USB1
node can get re-enabled.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
the 'soc' node in the MPC5125 "tower" board .dts has an '#interrupt-cells'
property although this node is not an interrupt controller
remove this erroneously placed property because starting with v3.13-rc1
lookup and resolution of 'interrupts' specs for peripherals gets misled
(tries to use the 'soc' as the interrupt parent which fails), emits
'no irq domain found' WARN() messages and breaks the boot process
[ best viewed with 'git diff -U5' to have DT node names in the context ]
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We are passing pointers to the firmware for reads, we need to properly
convert the result as OPAL is always BE.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
opal_xscom_read uses a pointer to return the data so we need
to byteswap it on LE builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A couple more device tree properties that need byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MSI code is miscalculating quotas in little endian mode.
Add required byteswaps to fix this.
Before we claimed a quota of 65536, after the patch we
see the correct value of 256.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to byteswap ibm,pcie-link-speed-stats.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The NVRAM code has a number of endian issues. I noticed a very
confused error log count:
RTAS: 100663330 -------- RTAS event begin --------
100663330 == 0x06000022. 0x6 LE error logs and 0x22 BE error logs.
The pstore code has similar issues - if we write an oops in one
endian and attempt to read it in another we get junk.
Make both of these formats big endian, and byteswap as required.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cpu_to_core_id() is missing a byteswap:
cat /sys/devices/system/cpu/cpu63/topology/core_id
201326592
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During on LE boot we see:
Partition configured for 1073741824 cpus, operating system maximum is 2048.
Clearly missing a byteswap here.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a bug in using ptrace to access FPRs via PTRACE_PEEKUSR /
PTRACE_POKEUSR. In effect, trying to access any of the FPRs always
really accesses FPR0, which does seriously break debugging :-)
The problem seems to have been introduced by commit 3ad26e5c44
(Merge branch 'for-kvm' into next).
[ It is indeed a merge conflict between Paul's FPU/VSX state rework
and my LE patches - Anton ]
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current logic sets the kdump base to min of 2G or ppc64_rma_size/2.
On PowerNV kernel the first memory block 'memory@0' can be very large,
equal to the DIMM size with ppc64_rma_size value capped to 1G. Hence on
PowerNV, kdump base is set to 512M resulting kdump to fail while allocating
paca array. This is because, paca need its memory from RMA region capped
at 256M (see allocate_pacas()).
This patch lowers the kdump base cap to 128M so that kdump kernel can
successfully get memory below 256M for paca allocation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have recently found out that no iommu_groups could be found under
/sys/ on a P8. That prevents PCI passthrough from working.
During my investigation, I found out there seems to be a missing
iommu_register_group for PHB3. The following patch seems to fix the
problem. After applying it, I see iommu_groups under
/sys/kernel/iommu_groups/, and can also bind vfio-pci to an adapter,
which gives me a device at /dev/vfio/.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bestcomm driver has been moved to drivers/dma, so to select
this driver by default additionally CONFIG_DMADEVICES has to be
enabled. Currently it is not enabled in the config despite existing
CONFIG_PPC_BESTCOMM=y in the config files. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At least some distros expect it these days; turn it on. Also, random
churn from doing a savedefconfig for the first time in a year or so.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
