Datasheet specifies that at the end of calibration the SDMMC_CALCR_EN
bit will be cleared. No commands should be send before calibration is
done.
Fixes: dbdea70f71 ("mmc: sdhci-of-at91: fix CALCR register being rewritten")
Fixes: 727d836a37 ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210924082851.2132068-2-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Old SDHI instances have a default value for the reset register which
keeps it in reset state by default. So, when applying a hard reset we
need to manually leave the soft reset state as well. Later SDHI
instances have a different default value, the one we write manually now.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826082107.47299-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The fault injection function can set EVENT_DATA_ERROR but skip the
setting of ->data_status to an error status if it hits just after a data
over interrupt. This confuses the tasklet which can later end up
triggering the WARN_ON(host->cmd || ..) in dw_mci_request_end() since
dw_mci_data_complete() would return success.
Prevent the fault injection function from doing this since this is not a
real case, and ensure that the fault injection doesn't race with a real
error either.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 2b8ac062f3 ("mmc: dw_mmc: Add data CRC error injection")
Link: https://lore.kernel.org/r/20210825114213.7429-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge misc updates from Andrew Morton:
"173 patches.
Subsystems affected by this series: ia64, ocfs2, block, and mm (debug,
pagecache, gup, swap, shmem, memcg, selftests, pagemap, mremap,
bootmem, sparsemem, vmalloc, kasan, pagealloc, memory-failure,
hugetlb, userfaultfd, vmscan, compaction, mempolicy, memblock,
oom-kill, migration, ksm, percpu, vmstat, and madvise)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (173 commits)
mm/madvise: add MADV_WILLNEED to process_madvise()
mm/vmstat: remove unneeded return value
mm/vmstat: simplify the array size calculation
mm/vmstat: correct some wrong comments
mm/percpu,c: remove obsolete comments of pcpu_chunk_populated()
selftests: vm: add COW time test for KSM pages
selftests: vm: add KSM merging time test
mm: KSM: fix data type
selftests: vm: add KSM merging across nodes test
selftests: vm: add KSM zero page merging test
selftests: vm: add KSM unmerge test
selftests: vm: add KSM merge test
mm/migrate: correct kernel-doc notation
mm: wire up syscall process_mrelease
mm: introduce process_mrelease system call
memblock: make memblock_find_in_range method private
mm/mempolicy.c: use in_task() in mempolicy_slab_node()
mm/mempolicy: unify the create() func for bind/interleave/prefer-many policies
mm/mempolicy: advertise new MPOL_PREFERRED_MANY
mm/hugetlb: add support for mempolicy MPOL_PREFERRED_MANY
...
Pages passed to block drivers can be mapped page cache pages, so we must
use flush_dcache_page here instead of the more limited
flush_kernel_dcache_page that is intended for highmem pages only.
Link: https://lkml.kernel.org/r/20210712060928.4161649-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alex Shi <alexs@kernel.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "_kernel_dcache_page fixes and removal".
While looking to convert the block layer away from kmap_atomic towards
kmap_local_page and prefeably the helpers that abstract it away I noticed
that a few block drivers directly or implicitly call
flush_kernel_dcache_page before kunmapping a page that has been written
to.
flush_kernel_dcache_page is documented to to be used in such cases, but
flush_dcache_page is actually required when the page could be in the page
cache and mapped to userspace, which is pretty much always the case when
kmapping an arbitrary page. Unfortunately the documentation doesn't
exactly make that clear, which lead to this misused. And it turns out
that only the copy_strings / copy_string_kernel in the exec code were
actually correct users of flush_kernel_dcache_page, which is why I think
we should just remove it and eat the very minor overhead in exec rather
than confusing poor driver writers.
This patch (of 6):
MIPS now implements flush_kernel_dcache_page (as an alias to
flush_dcache_page).
Link: https://lkml.kernel.org/r/20210712060928.4161649-1-hch@lst.de
Link: https://lkml.kernel.org/r/20210712060928.4161649-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Guo Ren <guoren@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Rich Felker <dalias@libc.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Alex Shi <alexs@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups.
-----BEGIN PGP SIGNATURE-----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=RXpg
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Return a proper response in case of an ioctl error
- Issue HPI to interrupt BKOPS for eMMC if it timed out
- Avoid hogging the CPU while polling for busy
- Extend sd8787 pwrseq to support the wilc1000 SDIO
- Remove a couple of confusing warning messages
- Clarify comment for ->card_busy() host ops
MMC host:
- dw_mmc: Add data CRC error injection
- mmci: De-assert reset during ->probe()
- rtsx_pci: Fix long reads when clock is pre-scaled
- sdhci: Correct the tuning command handle for PIO mode
- sdhci-esdhc-imx: Improve support for auto tuning
- sdhci-msm: Add support for the sc7280
- sdhci-of-arasan: Don't auto tune for DDR50 mode for ZynqMP
- sdhci-of-arasan: Enable support for auto cmd12
- sdhci-of-arasan: Use 19MHz for SD default speed for ZynqMP for level shifter
- usdhi6rol0: Implement the ->card_busy() host ops
MEMSTICK:
- A couple of minor cleanups"
* tag 'mmc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: queue: Remove unused parameters(request_queue)
mmc: pwrseq: sd8787: fix compilation warning
mmc: core: Return correct emmc response in case of ioctl error
mmc: sdhci-esdhc-imx: Select the correct mode for auto tuning
mmc: sdhci-esdhc-imx: Remove redundant code for manual tuning
mmc: core: Issue HPI in case the BKOPS timed out
mmc: queue: Match the data type of max_segments
mmc: switch from 'pci_' to 'dma_' API
memstick: switch from 'pci_' to 'dma_' API
memstick: r592: Change the name of the 'pci_driver' structure to be consistent
mmc: pwrseq: add wilc1000_sdio dependency for pwrseq_sd8787
mmc: pwrseq: sd8787: add support for wilc1000
dt-bindings: mmc: Extend pwrseq-sd8787 binding for wilc1000
dt-bindings: mmc: fsl-imx-esdhc: change the pinctrl-names rule
dt-bindings: mmc: fsl-imx-esdhc: add a new compatible string
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L bindings
dt-bindings: mmc: renesas,sdhi: Fix dtbs-check warning
mmc: core: Update ->card_busy() callback comment
mmc: usdhi6rol0: Implement card_busy function
mmc: sdhci: Correct the tuning command handle for PIO mode
...
This reverts commit 419dd626e3.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e3 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In function mmc_exit_request, the request_queue structure(*q) is not used.
I remove the unnecessary code related to the request_queue structure.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210825074601.8881-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixed compilation warning "cast from pointer to integer of
different size [-Wpointer-to-int-cast]"
Fixes: b2832b96fc ("mmc: pwrseq: sd8787: add support for wilc1000")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210825081931.598934-1-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC hardware auto tuning circuit support check 1/4/8 data lines and cmd
line. Out of reset uSDHC, it default select check 4 data lines and do not
check cmd line. This is incorrect if we use 8 data lines. So need to config
the auto tuning mode according to current bus width.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1629285415-7495-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For manual tuning method, already call esdhc_prepare_tuning() config the
necessary registers, so remove the redundant code in esdhc_writew_le() for
SDHCI_HOST_CONTROL2.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1629285415-7495-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support generic alternative_gpt_sector() block device operation.
It calculates location of GPT entry for eMMC of NVIDIA Tegra Android
devices. Add new MMC_CAP2_ALT_GPT_TEGRA flag that enables scanning of
alternative GPT sector and add raw_boot_mult field to mmc_ext_csd
which allows to get size of the boot partitions that is needed for
the calculation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210820004536.15791-4-digetx@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the BKOPS timed out, the card is probably still busy in the
R1_STATE_PRG. Rather than continue as nothing has happened and hitting and
error for the next command being sent, let's try to abort the running BKOPS
by sending a HPI command to get back into R1_STATE_TRAN.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210817224208.153652-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Each function has a different data type for max_segments,
Modify to match unsigned short(host->max_segs).
* unsigned short max_segs; /* see blk_queue_max_segments */
1) Return type : unsigned int
static unsigned int mmc_get_max_segments(struct mmc_host *host)
{
return host->can_dma_map_merge ? MMC_DMA_MAP_MERGE_SEGMENTS :
host->max_segs;
}
2) Parameter type : int
mmc_alloc_sg(mmc_get_max_segments(host), gfp);
-> static struct scatterlist *mmc_alloc_sg(int sg_len, gfp_t gfp)
3) Parameter type : unsigned short
blk_queue_max_segments(mq->queue, mmc_get_max_segments(host));
-> void blk_queue_max_segments(struct request_queue *q,
unsigned short max_segments)
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20210824073934.19727-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add new compatible for wilc1000 devices and specify the delay in .data
member of struct of_device_id. WILC1000, WILC3000 devices needs a minimum
of 5ms delay b/w reset and power lines.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210820092803.78523-3-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching card voltage to UHS voltage the mmc framework tries to
check the card busy signal, meaning the card pulling DAT0 line low,
before the switch is made. Drivers that does not implement the card_busy
function will manage to do the switch anyway, but the framework will
print a warning about not being able to verify the voltage signal.
Implement card_busy function.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20210816142314.1168-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci use PIO mode, and use mmc_send_tuning() to send the tuning
command, system will stuck because of the storm irq of sdhci. For PIO mode,
use mmc_send_tuning(), it will trigger buffer_read_ready interrupt and data
transfer complete interrupt. In current code logic, it will directly
return in sdhci_data_irq, can not call the sdhci_transfer_pio(). So the
buffer_read_ready interrupt storm happen. So for standard tuning method,
need to exclude this case.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628858041-1911-1-git-send-email-haibo.chen@nxp.com
[Ulf: Dropped redundant parenthesis in an expression]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor renesas_sdhi_probe() to avoid increasing numbers of
sdhi_quirks_match[] entry when we add other stable SoCs like
r8a779m*.
Note that the sdhi_quirks_match[] is only needed on
renesas_sdhi_internal_dmac.c so that of_data of
renesas_sdhi_sys_dmac.c keeps as-is.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210729103234.480743-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures at least if external TI SDMA is ever configured for sdhci.
For other external DMA cases, this is probably not currently an issue but
is still good to fix though.
Fixes: 18e762e3b7 ("mmc: sdhci: add support for using external DMA devices")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210810081644.19353-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Qcom SD controller defines the usage of 0xF in data
timeout counter register (0x2E) which is actually a reserved
bit as per specification. This would result in maximum of 21.26 secs
timeout value.
Some SDcard taking more time than 2.67secs (timeout value corresponding
to 0xE) and with that observed data timeout errors.
So increasing the timeout value to max possible timeout.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-3-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce max_timeout_count variable in the sdhci_host structure
and use in timeout calculation. By default its set to 0xE
(max timeout register value as per SDHC spec). But at the same time
vendors drivers can update it if they support different max timeout
register value than 0xE.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-2-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Print out the contents of the offending tuples when we do print them.
This can make it easier to debug, since these tuples are not exposed to
userspace anywhere else. We are limited to 64 bytes, so keep printing
out the full length in case the tuple is truncated.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-2-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.
Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Skip printing a retune error when we scan for a removed card because we
then expect a failed command.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210630041658.7574-1-wsa+renesas@sang-engineering.com
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the i.MX conversion to a DT-only platform, the mmc-esdhc-imx.h
header file is no longer used outside the driver, so move its content
to the sdhci-esdhc-imx driver and remove the header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210719193413.3792615-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Infinite loops are hard to read and understand because of
hidden main loop condition. Simplify such one in mmc_spi_skip().
Using schedule() to schedule (and be friendly to others)
is discouraged and cond_resched() should be used instead.
Hence, replace schedule() with cond_resched() at the same
time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210623101731.87885-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we find a reset handle when probing the MMCI block,
make sure the reset is de-asserted. It could happen that
a hardware has reset asserted at boot.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210630102408.3543024-1-linus.walleij@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095734.3046-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'of_property_read_variable_u32_array' function returns number
of elements read on success. This patch updates the condition
check in the driver to overwrite the tap values from DT if exist.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-8-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify the data type of the clk_phase array to u32 to make it compatible
with the argument requirement of "of_property_read_variable_u32_array".
Addresses-coverity: ("incompatible_param")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-7-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
