since it fails the virt_to_page() translation check with DEBUG_VIRTUAL
enabled.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Samsung DB-P70 somehow botched the first ICH9 SATA port. The board
doesn't expose the first port but somehow SStatus reports link online
while failing SRST protocol leading to repeated probe failures and
thus long boot delay.
Because the BIOS doesn't carry any identifying DMI information, the
port can't be blacklisted safely. Fortunately, the controller does
have subsystem vendor and ID set. It's unclear whether the subsystem
IDs are used only for the board but it can be safely worked around by
disabling SIDPR access and just using SRST works around the problem.
Even when the workaround is triggered on an unaffected board the only
side effect will be missing SCR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Jang <josephjang@gmail.com>
Reported-by: Jonghyon Sohn <mrsohn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata keeps a shadow copy of the ATA CTL register (which is write only),
and only writes to the hardware when the required value doesn't match
the shadow. However this copy wasn't being maintained when performing
reset functions. This could cause problems for the first operation after
a reset when the correct value might not be written to the CTL register.
This problem was observed when hotplugging a drive: the identify command
was being issued with interrupts enabled, when they should have been
disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a (rare) race condition in mv_interrupt() when using MSI.
The value of hpriv->main_irq_mask_addr can change on on the fly,
and without this patch we could end up writing back a stale copy
to the hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*netif_rx_* functions is obsolete and removed in newer kernels so
we need to use corresponding *napi_* functions instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For legacy applications stv0899 performs search only first time after insmod
due to not set DVBFE_ALGO_SEARCH_AGAIN bit
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> posted a patch series
to linux-pci to fix a wrong assumption about pci_bus->self==NULL for
all PCI host bus controllers. While PARISC platforms to not behave
this way, I prefer to have the code consistent across architectures.
The following patch replaces pci_bus->self with pci_bus->parent when
used as a test to check for "root bus controller".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Add braces around the macro arguments, else for example
"shl %r1, 5-3, %r2" would not expand to what you would assume.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix compile warnings:
drivers/scsi/zalon.c: In function `zalon_probe':
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_driver_string' from incompatible pointer type
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_name' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix those compile warnings:
uaccess.h:244: warning: `struct pt_regs' declared inside parameter list
uaccess.h:244: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
commit 11c3b5c3e0
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
- convert a few "if (xx) BUG();" to BUG_ON(xx)
- remove a few printk()s, as we get a backtrace with BUG_ON() anyway
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski noticed that the end condition for the loop in
bitmap_find_free_region() is wrong, and the "return if error" was also
using the wrong conditional that would only trigger if the bitmap was an
exact multiple of the allocation size, which is not necessarily the case
with dma_alloc_from_coherent().
Such a failure would end up in bitmap_find_free_region() accessing
beyond the end of the bitmap.
Reported-by: Guennadi Liakhovetski <lg@denx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A long time ago, xs->base is allocated a 4K size and all the contents
in the bucket are copied to the it. Now we use ocfs2_xattr_bucket to
abstract xattr bucket and xs->base is initialized to the start of the
bu_bhs[0]. So xs->base + offset will overflow when the value root is
stored outside the first block.
Then why we can survive the xattr test by now? It is because we always
read the bucket contiguously now and kernel mm allocate continguous
memory for us. We are lucky, but we should fix it. So just get the
right value root as other callers do.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
We need to use le32_to_cpu to test rec->e_cpos in
ocfs2_dinode_insert_check.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Replace max_inline_data with max_inline_data_with_xattr
to ensure it correct when xattr inlined.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
If this is a new directory with inline data, we choose to
reserve the entire inline area for directory contents and
force an external xattr block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: remove unused -r option for module-init-tool depmod
kbuild: fix 'make rpm' when CONFIG_LOCALVERSION_AUTO=y and using SCM tree
kbuild: fix mkspec to cleanup RPM_BUILD_ROOT
kbuild: fix C libary confusion in unifdef.c due to getline()
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: mm_cpumask for accessing the struct mm_struct's cpu_vm_mask.
cpumask: tsk_cpumask for accessing the struct task_struct's cpus_allowed.
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (f75375s) Remove unnecessary and confusing initialization
hwmon: (it87) Properly decode -128 degrees C temperature
hwmon: (lm90) Document support for the MAX6648/6692 chips
hwmon: (abituguru3) Fix I/O error handling
Trivial patch to fix bad links in the ext2 and ext3 documentation.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes-20090312' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci:
PCIe: portdrv: call pci_disable_device during remove
pci: Fix typo in message while disabling HT MSI mapping
pci: don't disable too many HT MSI mapping
powerpc/pseries: The RPA PCI hotplug driver depends on EEH
PCIe: AER: during disable, check subordinate before walking
PCI: Add PCI quirk to disable L0s ASPM state for 82575 and 82598
STag zero is a special STag that allows consumers to access any bus
address without registering memory. The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system). Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.
The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.
Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a report of a data corruption
http://lkml.org/lkml/2008/11/14/121. There is a script included to
reproduce the problem.
During testing, I encountered a number of strange things with ext3, so I
tried ext2 to attempt to reduce complexity of the problem. I found that
fsstress would quickly hang in wait_on_inode, waiting for I_LOCK to be
cleared, even though instrumentation showed that unlock_new_inode had
already been called for that inode. This points to memory scribble, or
synchronisation problme.
i_state of I_NEW inodes is not protected by inode_lock because other
processes are not supposed to touch them until I_LOCK (and I_NEW) is
cleared. Adding WARN_ON(inode->i_state & I_NEW) to sites where we modify
i_state revealed that generic_sync_sb_inodes is picking up new inodes from
the inode lists and passing them to __writeback_single_inode without
waiting for I_NEW. Subsequently modifying i_state causes corruption. In
my case it would look like this:
CPU0 CPU1
unlock_new_inode() __sync_single_inode()
reg <- inode->i_state
reg -> reg & ~(I_LOCK|I_NEW) reg <- inode->i_state
reg -> inode->i_state reg -> reg | I_SYNC
reg -> inode->i_state
Non-atomic RMW on CPU1 overwrites CPU0 store and sets I_LOCK|I_NEW again.
Fix for this is rather than wait for I_NEW inodes, just skip over them:
inodes concurrently being created are not subject to data integrity
operations, and should not significantly contribute to dirty memory
either.
After this change, I'm unable to reproduce any of the added warnings or
hangs after ~1hour of running. Previously, the new warnings would start
immediately and hang would happen in under 5 minutes.
I'm also testing on ext3 now, and so far no problems there either. I
don't know whether this fixes the problem reported above, but it fixes a
real problem for me.
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even when page reclaim is under mem_cgroup, # of scan page is determined by
status of global LRU. Fix that.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device. As a result, we end up with no backlight device at all.
We should instead disable it if there is an ACPI device, as the other
laptop drivers do. This regression was introduced in febf2d9 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").
Each laptop driver with backlight support got a similar change around
febf2d9. The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change. The regression is also in
2.6.28.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
