with "apic=verbose" the print_IO_APIC() function tries to print
IRQ to pin mappings for every active irq. It assumes chip_data
is of type irq_cfg and may cause an oops if not.
As the print_IO_APIC() is called from a late_initcall other
chained irq chips may already be registered with custom
chip_data information, causing an oops. This is the case with
intel MID SoC devices with gpio demuxers registered as irq_chips.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
[ -v2: fixed build failure ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
lapic timer calibration can be combined with tsc in platform
specific calibration functions. if such calibration result is
obtained early, we can skip the redundant calibration loops.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
nr_legacy_irqs is set in probe_nr_irqs_gsi, we should not clear
it after that. Otherwise, the result is that MSI irqs will be
allocated from the wrong range for the systems without legacy
PIC.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Standardize on CONFIG_SPARSE_IRQ=y
x86, ioapic: Clean up ioapic/apic_id usage
x86, ioapic: Factor out print_IO_APIC() to only print one io apic
x86, ioapic: Print out irte with right ioapic index
x86, ioapic: Split up setup_ioapic_entry()
x86, ioapic: Pass struct irq_attr * to setup_ioapic_irq()
apic, i386/bigsmp: Fix false warnings regarding logical APIC ID mismatches
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
Sparseirq got introduced in v2.6.28 and Thomas did a huge cleanup
around v2.6.38 that eliminated basically all disadvantages
of it.
So we can remove non-sparseirq support now and simplify
our IRQ degrees of freedom a bit.
Suggested-and-acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4E95E21D.6090200@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While looking at the code, apic_id sometime is referred to index
of ioapic, but sometime is used for phys apic id. and some even
use apic for real apic id. It is very confusing.
So try to limit apic_id or ioapic_id to be real apic id for
ioapic, and use ioapic_idx for ioapic index in the array.
-v2: Suggested by Ingo, use ioapic_idx consistently, instead of ioapic
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542DC.3090509@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is getting too big after the interrupt remaping entries debug
print out was added.
Original print_IO_APIC() becomes print_IO_APICs().
New print_IO_APIC() will only print one ioapic's registers
As a side-effect this clean-up also made checkpatch.pl happier.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542D3.5000008@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo pointed out that setup_ioapic_entry() is way too big now.
Split the intr-remap code out into setup_ir_ioapic_entry().
Also pass struct io_apic_irq_attr * instead of 5 parameters
in those two functions.
At last in setup_ir_ioapic_entry() we don't need to panic.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542BB.4070807@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do not expand that struct, and just pass pointer to reduce the
number of parameters in related functions.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/4E9542B1.7050800@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just convert all the files that have an nmi handler to the new routines.
Most of it is straight forward conversion. A couple of places needed some
tweaking like kgdb which separates the debug notifier from the nmi handler
and mce removes a call to notify_die.
[Thanks to Ying for finding out the history behind that mce call
https://lkml.org/lkml/2010/5/27/114
And Boris responding that he would like to remove that call because of it
https://lkml.org/lkml/2011/9/21/163]
The things that get converted are the registeration/unregistration routines
and the nmi handler itself has its args changed along with code removal
to check which list it is on (most are on one NMI list except for kgdb
which has both an NMI routine and an NMI Unknown routine).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1317409584-23662-4-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These warnings (generally one per CPU) are a result of
initializing x86_cpu_to_logical_apicid while apic_default is
still in use, but the check in setup_local_APIC() being done
when apic_bigsmp was already used as an override in
default_setup_apic_routing():
Overriding APIC driver with bigsmp
Enabling APIC mode: Physflat. Using 5 I/O APICs
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
...
CPU 1 irqstacks, hard=f1c9a000 soft=f1c9c000
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 9e000
Initializing CPU#1
------------[ cut here ]------------
WARNING: at .../arch/x86/kernel/apic/apic.c:1239
setup_local_APIC+0x137/0x46b() Hardware name: ...
CPU1 logical APIC ID: 2 != 8
...
Fix this (for the time being, i.e. until
x86_32_early_logical_apicid() will get removed again, as Tejun
says ought to be possible) by overriding the previously stored
values at the point where the APIC driver gets overridden.
v2: Move this and the pre-existing override logic into
arch/x86/kernel/apic/bigsmp_32.c.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org> (2.6.39 and onwards)
Link: http://lkml.kernel.org/r/4E835D16020000780005844C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For older IO-APIC's, we were clearing the remote-IRR by changing
the RTE trigger mode to edge and then back to level. We wanted
to mask the RTE during this process, so we were essentially
doing mask+edge and then to unmask+level.
As part of the commit ca64c47cec,
we moved this EOI process earlier where the IO-APIC RTE is
masked. So we were wrongly unmasking it in the eoi_ioapic_irq().
So change the remote-IRR clear sequence in eoi_ioapic_irq() to
mask + edge and then restore the previous RTE entry which will
restore the mask status as well as the level trigger.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Rafael Wysocki <rjw@novell.com>
Cc: lchiquitto@novell.com
Cc: jbeulich@novell.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110825190657.210286410@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the kdump scenario mentioned below, we can have a case where
the device using level triggered interrupt will not generate any
interrupts in the kdump kernel.
1. IO-APIC sends a level triggered interrupt to the CPU's local APIC.
2. Kernel crashed before the CPU services this interrupt, leaving
the remote-IRR in the IO-APIC set.
3. kdump kernel boot sequence does clear_IO_APIC() as part of IO-APIC
initialization. But this fails to reset remote-IRR bit of the
IO-APIC RTE as the remote-IRR bit is read-only.
4. Device using that level triggered entry can't generate any
more interrupts because of the remote-IRR bit.
In clear_IO_APIC_pin(), check if the remote-IRR bit is set and if
so do an explicit attempt to clear it (by doing EOI write on
modern io-apic's and changing trigger mode to edge/level on
older io-apic's). Also before doing the explicit EOI to the
io-apic, ensure that the trigger mode is indeed set to level.
This will enable the explicit EOI to the io-apic to reset the
remote-IRR bit.
Tested-by: Leonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=701686
Cc: Rafael Wysocki <rjw@novell.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: jbeulich@novell.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110825190657.157502602@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On the platforms which are x2apic and interrupt-remapping
capable, Linux kernel is enabling x2apic even if the BIOS
doesn't. This is to take advantage of the features that x2apic
brings in.
Some of the OEM platforms are running into issues because of
this, as their bios is not x2apic aware. For example, this was
resulting in interrupt migration issues on one of the platforms.
Also if the BIOS SMI handling uses APIC interface to send SMI's,
then the BIOS need to be aware of x2apic mode that OS has
enabled.
On some of these platforms, BIOS doesn't have a HW mechanism to
turnoff the x2apic feature to prevent OS from enabling it.
To resolve this mess, recent changes to the VT-d2 specification:
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
includes a mechanism that provides BIOS a way to request system
software to opt out of enabling x2apic mode.
Look at the x2apic optout flag in the DMAR tables before
enabling the x2apic mode in the platform. Also print a warning
that we have disabled x2apic based on the BIOS request.
Kernel boot parameter "intremap=no_x2apic_optout" can be used to
override the BIOS x2apic optout request.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.171766616@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Delete the 10 msec delay between the INIT and SIPI when starting
slave cpus. I can find no requirement for this delay. BIOS also
has similar code sequences without the delay.
Removing the delay reduces boot time by 40 sec. Every bit helps.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20110805140900.GA6774@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-detect-hyper-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hyper: Change hypervisor detection order
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix DNA exception during check_fpu()
* 'x86-kexec-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kexec, x86: Fix incorrect jump back address if not preserving context
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, config: Introduce an INTEL_MID configuration
* 'x86-quirks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, quirks: Use pci_dev->revision
* 'x86-tsc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: tsc: Remove unneeded DMI-based blacklisting
* 'x86-smpboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, boot: Wait for boot cpu to show up if nr_cpus limit is about to hit
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ioapic: Print IR_IO_APIC_route_entry when IR is enabled
x86, ioapic: Print IRTE when IR is enabled
x86, x2apic: Preserve high 32-bits of IA32_APIC_BASE MSR
x86, ioapic: Also print Dest field
x86, ioapic: Format clean up for IOAPIC output
x86: print APIC data a little later during boot
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
When "apic=debug" is used as a boot parameter, Linux prints the IOAPIC routing
entries in "dmesg". Below is output from IOAPIC whose apic_id is 8:
# dmesg | grep "routing entry"
IOAPIC[8]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
IOAPIC[8]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
IOAPIC[8]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0)
...
Similarly, when IR (interrupt remapping) is enabled, and the IRTE
(interrupt remapping table entry) is set up we should display it.
After the fix:
# dmesg | grep IRTE
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:31 Dest:00000000 SID:00F1 SQ:0 SVT:1)
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:30 Dest:00000000 SID:00F1 SQ:0 SVT:1)
IOAPIC[8]: Set IRTE entry (P:1 FPD:0 Dst_Mode:0 Redir_hint:1 Trig_Mode:0 Dlvry_Mode:0 Avail:0 Vector:33 Dest:00000000 SID:00F1 SQ:0 SVT:1)
...
The IRTE is defined in Sec 9.5 of the Intel VT-d Specification.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110712211704.2939.71291.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The code in setup_ioapic_irq() determines the Destination Field,
so why not also include it in the debug printk output that gets
displayed when the boot parameter "apic=debug" is used.
Before the change, "dmesg" will show:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) ...
After the change, you will see:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) ...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184603.2734.91071.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When IOAPIC data is displayed in "dmesg" with the help of the
boot parameter "apic=debug" certain values are not formatted
correctly wrt their size.
In the "dmesg" snippet below, note that the output for "max
redirection entries", and "IO APIC version" which are each
defined to be just 8-bits long are displayed as 2 bytes in
length. Similarly, "Dst" under the "IRQ redirection table"
should only be 8-bits long.
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 000 1 0 0 0 0 0 0 00
01 000 0 0 0 0 0 0 0 31
02 000 0 0 0 0 0 0 0 30
03 000 1 0 0 0 0 0 0 33
...
...
Do some formatting clean up, so you will see output like below:
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 17
....... : PRQ implemented: 0
....... : IO APIC version: 20
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 00 1 0 0 0 0 0 0 00
01 00 0 0 0 0 0 0 0 31
02 00 0 0 0 0 0 0 0 30
03 00 1 0 0 0 0 0 0 33
...
...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184557.2734.61830.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
nr_cpus allows one to specify number of possible cpus in the system.
Current assumption seems to be that first cpu to show up is boot cpu
and this assumption will be broken in kdump scenario where we can be
booting on a non boot cpu with nr_cpus=1.
It might happen that first cpu we parse is not the cpu we boot on and
later we ignore boot cpu. Though code later seems to recognize this
anomaly and forcibly sets boot cpu in physical cpu map with following
warning.
if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) {
printk(KERN_WARNING
"weird, boot CPU (#%d) not listed by the BIOS.\n",
hard_smp_processor_id());
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
This patch waits for boot cpu to show up and starts ignoring the cpus
once we have hit (nr_cpus - 1) number of cpus. So effectively we are
reserving one slot out of nr_cpus for boot cpu explicitly.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20110708171926.GF2930@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Compare only lower 32 bits of framebuffer map offsets
drm/i915: Don't leak in i915_gem_shmem_pread_slow()
drm/radeon/kms: do bounds checking for 3D_LOAD_VBPNTR and bump array limit
drm/radeon/kms: fix mac g5 quirk
x86/uv/x2apic: update for change in pci bridge handling.
alpha, drm: Remove obsolete Alpha support in MGA DRM code
alpha/drm: Cleanup Alpha support in DRM generic code
savage: remove unnecessary if statement
drm/radeon: fix GUI idle IH debug statements
drm/radeon/kms: check modes against max pixel clock
drm: fix fbs in DRM_IOCTL_MODE_GETRESOURCES ioctl
When I added 3448a19da4
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are multiple declarations of global_clock_event in header files
specific to particular clock event implementations. Consolidate them
in <asm/time.h> and make sure all users include that header.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Venkatesh Pallipadi (Venki) <venki@google.com>
Link: http://lkml.kernel.org/r/20110601180610.762763451@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds support for a new version of the SGI UV hub
chip. The hub chip is the node controller that connects multiple
blades into a larger coherent SSI.
For the most part, UV2 is compatible with UV1. The majority of
the changes are in the addresses of MMRs and in a few cases, the
contents of MMRs. These changes are the result in changes in the
system topology such as node configuration, processor types,
maximum nodes, physical address sizes, etc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110511175028.GA18006@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In mask/restore_ioapic_entries() we should be restoring ioapic
entries when ioapics[apic].saved_registers is not NULL.
Fix the typo and address the resume hang regression reported by
Linus.
This was not found sooner because the systems where these
changes were tested on kept the IO-APIC entries intact over
resume.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1306259131.7171.7.camel@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Include module.h header in apic_flat_64.c
x86, apic: Make apic drivers static
x86, apic: Clean up bigsmp apic selection code
x86, apic: Use .apicdrivers section for the apic drivers list
x86, apic: Introduce .apicdrivers section to find the list of apic drivers
x86, x2apic: Move the common bits to x2apic.h
x86, x2apic: Minimize IPI register writes using cluster groups
x86, x2apic: Track the x2apic cluster sibling map
x86, x2apic: Remove duplicate code for IPI mask routines
x86, apic: Use probe routines to simplify apic selection
x86, ioapic: Consolidate mp_ioapic_routing[] into 'struct ioapic'
x86, ioapic: Consolidate gsi routing info into 'struct ioapic'
x86, ioapic: Consolidate mp_ioapics[] into 'struct ioapic'
x86, ioapic: Consolidate ioapic_saved_data[] into 'struct ioapic'
x86, ioapic: Add struct ioapic
x86, ioapic: Remove duplicate code for saving/restoring RTEs
x86, ioapic: Use ioapic_saved_data while enabling intr-remapping
x86, ioapic: Allocate ioapic_saved_data early
x86, ioapic: Fix potential resume deadlock
apic_flat_64.c needs to include module.h because it uses
EXPORT_SYMBOL_GPL().
This fixes these warnings on some !SMP randconfigs:
arch/x86/kernel/apic/apic_flat_64.c:31: warning: data definition has no type or storage class
arch/x86/kernel/apic/apic_flat_64.c:31: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/x86/kernel/apic/apic_flat_64.c:31: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20110523104300.dd532a99.randy.dunlap@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before the conversion of the NMI watchdog to perf event, the
watchdog timeout was 5 seconds. Now it is 60 seconds. For my
particular application, netbooks, 5 seconds was a better
timeout. With a short timeout, we catch faults earlier and are
able to send back a panic. With a 60 second timeout, the user is
unlikely to wait and will instead hit the power button, causing
us to lose the panic info.
This change configures the NMI period to watchdog_thresh and
sets the softlockup_thresh to watchdog_thresh * 2. In addition,
watchdog_thresh was reduced to 10 seconds as suggested by Ingo
Molnar.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1306127423-3347-4-git-send-email-msb@chromium.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071642.GF22305@elte.hu>
This will pave the way for each apic driver to be self-contained
and eliminate the need for apic_probe[].
Order in which apic drivers are listed in the .apicdrivers
section is important, as this determines the apic probe order.
And this is enforced by the ordering of apic driver files in the
Makefile and the macros apic_driver()/apic_drivers().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: gorcunov@openvz.org
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110521005526.068775085@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
