The PHY type defines are no longer used in the PCIe, UFS and USB QMP
drivers so drop the corresponding include.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221111094239.11547-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the start and pwrdn-ctrl abstractions which are no longer needed
since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-18-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It typically takes between one and two milliseconds for the PHY to
become ready after starting it. Increase the tight 3--10 us polling
period to the more reasonable 51--200 us.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012085002.24099-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY ready and status polling by dropping the configuration
masks which are no longer needed since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power-down delay was included in the first version of the QMP driver
for MSM8996 as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant configuration
options while increasing the unnecessarily low timer slack somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MSM8996 QMP PCIe PHY driver no longer uses the "in-layout"
configuration macro to configure registers that are typically accessed
using "regs_layout" arrays (e.g. QPHY_START_CTRL) so drop this unused
feature.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Regulator core already logs an error message in case requesting a
regulator fails so drop the mostly redundant error message from probe.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This driver uses v2 registers only so drop the unnecessary
POWER_DOWN_CONTROL override.
Note that this register is already hard-coded when powering on the PHY.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221017065013.19647-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All QMP drivers but the MSM8996 and combo ones handle exactly one PHY
and the corresponding memory resources are not per-lane, but per PHY.
Update the obsolete comments.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221017065013.19647-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220924070300.25080-3-yuancan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The nlanes configuration parameter is really the number of PHYs provided
by this QMP block on MSM8996. Rename it accordingly.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220920073826.20811-14-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the removed mode field from the struct qmp_phy kernel doc.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220920073826.20811-9-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Only the combo QMP driver needs a forward declaration of struct qmp_phy.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220920073826.20811-8-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The configuration PHY type is no longer used since the QMP driver split
so drop it from the configuration.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220920073826.20811-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MSM8996 QMP PHY driver does not use the PCS_MISC IO region (and
neither do the DT binding specify it) so remove the corresponding code
from the driver.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220916102340.11520-8-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220916102340.11520-4-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver function prefix has gotten unnecessarily long and hurts
readability.
Shorten "qcom_qmp_phy_" to "qmp_" (which likely stands for "Qualcomm
Multi PHY" or similar anyway).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220907110728.19092-15-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the secondary register initialisation tables which aren't used by
this driver.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220907110728.19092-14-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drivers should in general not log anything during unless there are
errors.
Drop the pointless registration info message from the QMP drivers.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220907110728.19092-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the unused and incomplete runtime PM implementation, which was
only used by USB PHYs before splitting the QMP driver.
Note that the runtime PM was never disabled (and state restored) on
driver unbind.
This effectively reverts commit ac0d239936 ("phy: qcom-qmp: Add
support for runtime PM").
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220907110728.19092-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The lane reset is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the reset name.
Update driver to support the new binding where the "lane" reset name has
been deprecated by instead requesting the reset by index.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220830112923.3725-30-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pipe clock is defined in the "lane" node so there's no need to keep
adding a redundant lane-number suffix to the clock name.
Update driver to support the new binding where the pipe clock name has
been deprecated by instead requesting the clock by index.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220830112923.3725-29-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Other PHYs tables directly reference QPHY_PLL_LOCK_CHK_DLY_TIME register
without using reglayout. Define corresponding register to be used by
msm8996 PHY tables and use it directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220705094320.1313312-29-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Other PHYs tables directly reference FLL registers without using
reglayout. Define corresponding registers to be used by msm8996 PHY
tables and use them directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220705094320.1313312-28-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the obsolete pipe clock handling which was used to treat the pipe
clock as optional for types other than PCIe and USB and which is no
longer needed since splitting the PHY driver.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220623113314.29761-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace init/exit ops with power_on/power_off which should be used for
the PCIe PHYs to fix PHY initialization.
Fixes: f575ac2d64 ("phy: qcom-qmp-pcie-msm8996: drop support for non-PCIe PHY types")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220610185542.3662484-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch qcom-qmp-pcie-msm8996 driver to use reset_control_bulk_assert /
_deassert functions rather than hardcoding the loops in the driver
itself.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-30-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove the conditionals and options that are not used by the MSM8996
PCIe PHY device. Hardcode has_lane_rst and has_phy_com_ctrl as this is
the case for this PHY.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-22-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop remaining support for PHY types other than PCIe.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-17-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Change all symbol names to start with qcom_qmp_phy_pcie_msm8996_ rather
than old qcom_qmp_phy_.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-10-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop support for all compatibles from the new qmp-pcie driver except the
qcom,msm8996-qmp-pcie-phy. This PHY differs from the rest of PCIe PHYs,
so it warrants a separate device driver.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In order to split and cleanup the single monstrous QMP PHY driver,
create blind copies of the current file. They will be used for:
- PCIe (and a separate msm8996 PCIe PHY driver)
- UFS
- USB
- Combo DP + USB
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org> # UFS, PCIe and USB on SC8180X
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220607213203.2819885-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
